i have a orange m3100 version of the hermes.
recently i flashed it with schaps 3.54b rom
now i can't use my wifi router/network @ home nor another wifi router/network @ work.
in fact i'm well connected, i'm sure of this because from another computer of the networks, i can ping the (static) ip of my hermes. i tried changing and changing again my ip and tested it.
but the hermes cant go on internet.
i use the right gateway and DNS in each case but no surf in pocket ie.
any solutions or other tests i can do?
in french if possible since i and my rom are in french.
thank you.
update : i made some tests :
it is nos a dns problem : i put the right gateway and dns on the smartphone but i cant get a website by typing its ip in pocket ie adress bar (other browsers dont work better) and i cant even access my router admin interface.
when i'm trying wifi with static ip or dhcp on my m3100, i can ping its ip from another computer of my networks and the smartphone responds ok, and i can see its mac adress in the connected clients on my router config screen. But the smartphone can't ping anyone.
i asked a friend who told me that the proxy (192.168.10.100 :8080 ) used for the connection to orangeworld in gprs/edge is also used when i try to connect via wifi and that is why it cant connect nowhere because my personal network is configured differently and without a proxy.
if i delete the proxy my connections will cost me more when i use gprs.
if i configure my router like this (192.168.10.xxx) with a proxy on 8080 it could work but only on my network and not @ my workplace or somewhere else where network params will be different.
any ideas or solutions ?
wow ! so many people trying to help :/
well i found a temporary solution to my problem, probably not the best one but the best i can do by myself so if someone wants to help : thank you
it was actually a proxy problem.
i looked in the registry and found a key where the proxy adress was detailed : 192.168.10.100:8080
i have exported this value as "proxon.reg"
then i modified the value by deleting its content and i exported the empty value as "proxoff.reg"
now i have my "proxy switch".
before activating the wifi and starting ie, i lauch "proxoff.reg" which clean the registry for the proxy data and magic : ie connects fine.
and when i want tu surf via my provider orange, i desactivate the wifi and launch "proxon.reg" which restore the correct proxy data to the registry. and i can surf on gprs/edge.
all this is fine when i switch off the phone functions in the comm manager.
but now i need someone to tell me how i can automatize this for the wifi and edge connections because if the wifi signal gets too weak, i dont want my phone to switch to the gsm when the proxy is desactivated.
i hope you can understand my english.
please help.
In the last version of BatteryStatus (http://forum.xda-developers.com/showthread.php?t=270751) you can find,among the others stuffs, the "Disable Proxy for WiFi" option (see the Tools tab)... Maybe more simple than "regg-in" on and off? I'm ok with it, try and see if it's ok for you also...
Bye!
hey kamaal i just downloaded the batterstatus program but im not seeing the "Disable Proxy for WiFi" option in the Tools tab
***edit:
sorry i downloaded the extended version beta and it was there
Related
im trying to get an internet connection through my wifi connection. i have done search's and lots of people seem to be asking the same question but nobody has the answer.
at the moment i can access my c: using an application called Resco explorer. but i can not connect to the internet. im not sure what setting i should have on the wifi manger and on my pc. im also using AOL as my isp.
PLS PLS help :lol:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
looks like a no then
I got mine working but setting my wireless network adapter to connect to "Work".
Under Settings>Connections>Tasks>Manage existing connections>Proxy Settings> check the "This network connects to the internet" box
then
Under Settings>Connections>Advanced>Select Networks> "Programs that automatically connect to the internet should connect using:" to "My Work Network" (and the same with one for private network)
Also in your active sync settings, make sure your connection settings allow network (Ethernet) and RAS connections.
From previous research around this, i'm pretty sure you can only use the internet pass through under "WORK" settings only.
*thought i'd better register and contribute as i've gained a fair bit from this forum.
no good anyother ideas. i have searched through hundreds of threads and still no go
help pls
Make sure you have "Enable Netbios over TCP/IP" checked in your TCP/IP Advanced settings.
i have done this on both my wifi network and my isp network.
still not working
Have you checked if you're getting an IP address from your Wireless Router's DHCP server? Also DNS settings and Gateway address should be there.
You can check this easily by using vxUtil (free )
these are my settings:
tiacxwln1 - tiacxwln compatible wireless
Ip address 192.168.0.2
subnet mask 255.255.255.0
default gateway 192.168.0.1
primary DNS 192.168.0.1
secondary dns
primary wins
seconfdary wins
DHCPs server 192.168.0.1
under serial usb
IP address 192.168.55.101
subnet mask 255.255.255.0
default gateway 192.168.55.100
primary DNS 127.0.0.1
Getting this error when I tried to allow my broadband connection to share with my wifi connection. If I unplug the wifi connection and try and share with another network I don’t get any errors.
Internet connection sharing (ics) cannot be enabled due to IP address conflict on the network. ICS requires the host be configured to use 192.168.0.1 please ensure that no other client on the network is configured to use 192.168.0.1
hmmm ... ever had the same problem. all devices are able to connect to the same router except mine sx66.
then i change the router's channel to '1' .. tada .. now everyone is connected. it might sounds silly, but it worked for me.
try changing your ap wireless channel.
Re: does NE1 have the answer to wifi not connecting to the n
robboy said:
Edit:
also i can not connect to activesync (version 3.8.0) via wifi. maybe if i was able to connect to this the internet would work as it does when its docked??????
Click to expand...
Click to collapse
i found the problem with activesync 3.8 and 4.0 somehow, so i reverted back to 3.7, now wifi can sync.
afaik, connecting to internet has nothing to do with activesync. its a direct connection to wifi router. use work location and check the proxy settings if u hv any? (at home i use connect to internet without proxy, at work i use connect to internet with proxy).
Also, for Activsync with wifi, make sure that the WINS server address is that of yr PC u want to sync with.
Hi,
I'm experiencing a weird problem and please let me know if it's only my problem or there is some work around for it.
My phone is SX66 upgraded to 1.40 ROM + 1.13 Radio stack
I can connect Wifi fine whenever I have some phone signal (at work). Whenever I go home where the phone signal is weak then the WIFI couldn't get connected (I believe I set up my home network correctly as I've been using it for so long and configure it for several computer/laptop in house). The network could detect the AP with the SSID but I just couldn't connect to it even I'm sitting right next to the AP.
ROM 1.40
Radio: 1.13
MDD
Are you sure it isn't connecting? What has led you to this conclusion?
Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
If you're sure you're just not connecting however, things to check are;
WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
Interference - Wireless A/V Senders and digital cordless phones are common culprits for RFI. 802.11x APs support multiple channels (most default to channel 11), and you can change these in case of interference. Once again, if you have other WiFi gear already connected with good, strong signals, you can probably discount this one.
Sorry if this is all elementary to you - I don't know how technical you are.
Thanks for your reply.
> Are you sure it isn't connecting? What has led you to this conclusion?
Yes, I've check wireless status on the phone. "Connected to the network", and the AP with DHCP on showed the status of an IP has been allocate to the SX66 mac address. However I dont' really believe it then I check the "Adater", it said network available, and the WIFI icon just didnot show any traffic.
> Is it possible that it is connecting, but that you just can't browse the internet, in which case check your connection proxy settings. If your work uses a proxy server and you've enabled the pass-through setting in ActiveSync, your network connection may be configured with your work proxy server.
I've experience once with the internet connection via Active Sync so I disable the passthrough. Both home and work doesn't have proxy server so I selected not to have any on the phone.
> WEP/WPA Encryption - If you're using it and have other wireless devices on your network, you no doubt know what to do. If not, say so & I can help you.
At work, I have 128 WEP and the connection works fine with the key. At home, I open my network but using MAC filtering to protect it. I have problem with the open network one at home. Perhaps, I will try to setup WEP at home and see if it can work.
The only thing I'm not really clear is the difference between setting "WPA" and "WPA-PSK" from the phone.
> DHCP - Does your router/AP support Auto-IP Addressing? Is it enabled? If not, you'll have to configure the WiFi card with a static IP within the same subnet as your router. Ask if you need help.
Yes, DHCP enable as I don't want to change it back and forth when traveling.
> MAC Filtering - Are you blocking unauthorised MAC Addresses (on your router/ap)?
I do it and I already opened the network and then captured the MAC address into the AP memory. (that's why I think it's connected but will check).
> Interference -
Not really, I'm 6' away from the AP and I don't have any cordless device in my computer room.
> Sorry if this is all elementary to you - I don't know how technical you
are.
No problem, I'd like to learn more about this PDA. The concept is about the same with PC, but the tools to debug is not there. I can't use tracert/traceroute, ifconfig or ping broadcast to really know if I'm the network.
Once again, thanks a lot.
Okay, well it sounds like you're on the right track & know what you're doing.
A useful troubleshooting tool, which gives you tracert, ping, whios, ipconfig and a host of other tools is "vxUtil", which is freeware. I'd give you a URL for downloading it, but I'm on my iMate now (sipping coffee by the Yarra in a Melbourne Cafe - oh what a techno-wanker am I!), but search these forums or Google it and you'll find it.
Now, regarding the proxy thing... These PPCs are a little tricky with their internet settings, and I had to create a different 'connect using...' connection profile, if that makes sense. The important setting within the profile, which is under the Proxy tab, from memory, is "This network connects to the internet".
Now for some reason, if you don't enter in a proxy server here, that check-box doesn't stay checked when you ok your way out. So what I've had to do is go into the advanced area & enter anything in the "wap" proxy, then ok out.
Strange, but it seems to work. Although I always leave my "Private network" on "My Work Network", I can now browse the 'Net through the WiFi AP/Router.
Download vxUtil & see if you can ping your AP, then go from there.
I've worked around the problem by using static IP address instead of depending on DHCP. Thanks to Hitchhiker software. I noticed that it was trying to obtain IP address from DHCP but failed. (The very same DHCP work wells for the rest of my network). Anyway, I will use Hitchhiker to switch IP back and forth if necessary.
Thanks a lot!
MDD
Great to hear you found the problem - well done.
Hi!
I haven't seen any application that can do this after some time looking for it, and I think it may well be the case with some of us.... let me explain..
When at home, I can have a WIFI connection to my home ADSL which needs a 'clean configuration'.. ie.. DHCP address and NO PROXY.
But, when at the office, I can also get the address thru DHCP, but I need to configure a proxy to be able to connect to Internet....
Plus, at some of the sites I work in, I need not only a different proxy, but a 'manually' configured address.
Well, the question... Is there any application that can help with the switching of environements, based, for instance, in the SID of the access point available?
I've seen apps such as CommMgrPro that can 'switch' profiles based on the pohone cell-id (which could also be fine to define your location), but you can only 'switch ON and OFF the WIFI (or any other) connection, but in no case can I manage the proxy (BTW this is a difficult setting to handle even manually!)
Thanks
Prof
http://forum.xda-developers.com/showthread.php?t=355936
Hi
This is a nice program.
But I cant download from your website.
But my Site is online
Here is the link:
http://blog.renestein.net/Wifi+Profiles+For+Windows+Mobile+English+Version.aspx
wow fixes my samsugn gt i8000 wifi problem thanks a lot
take a look at here:
http://forum.xda-developers.com/showthread.php?t=690963
hey i am currently running Schap's 4.01 and the internet and mms and email are all working but my problem comes with the phone using WIFI to connect to the internet, i connect and all to the router but i am not able to browse the internet, i am also using tmobiles proxy to connect to the internet. how can i fix this?
i think i have almost the same problem with orange france proxy : no problem browsing via phone but no browsing possible via wifi, even if connected, and i'm connected to my wifi network : i can see [email protected] of my hermes is visible in my router admin screen. others can ping me, i can ping others and my router . but no browsing possible.
my (dirty) solution : i made 2 regs, one for disabling (delete) the orange proxy data in the registry, and the other for re enabling the proxy adress.
i launch the first "proxyoff".reg before i use wifi and launch the 2° one "proxyon.reg" when i quit wifi browsing.
but i'm sure there is a better way to do, so if someone gets it....
hey kaiser can you upload those proxyoff and on registry files for me?
i don't know how to include an attachment here so i give you the content of my "proxyoff.reg" :
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\\Comm\ConnMgr\Providers\{EF097F4C-DC4B-4c98-8FF6-AEF805DC0E8E}\HTTP-{FF445A54-ADF8-4FAB-86B7-E31482BEE8BE}]
"Proxy"=""
"ConnectionGUID"="{F7E5622E-1BAD-C180-6119-F93AE16AA2B0}"
"ExtraInfo"=""
"Override"=""
"Username"=""
"Enable"=dword:00000001
"Type"=dword:00000001
"DestId"="{436EF144-B4FB-4863-A041-8F905A62C572}"
"SrcId"="{FF445A54-ADF8-4FAB-86B7-E31482BEE8BE}"
and here is the content of my "proxyon.reg" :
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\\Comm\ConnMgr\Providers\{EF097F4C-DC4B-4c98-8FF6-AEF805DC0E8E}\HTTP-{FF445A54-ADF8-4FAB-86B7-E31482BEE8BE}]
"Proxy"="192.168.10.100:8080"
"ConnectionGUID"="{F7E5622E-1BAD-C180-6119-F93AE16AA2B0}"
"ExtraInfo"=""
"Override"=""
"Username"=""
"Enable"=dword:00000001
"Type"=dword:00000001
"DestId"="{436EF144-B4FB-4863-A041-8F905A62C572}"
"SrcId"="{FF445A54-ADF8-4FAB-86B7-E31482BEE8BE}"
it was on the previous schaps rom i used , i have not used them on my actual 4.01 yet but it shoud make no difference. and the proxy @ is for orange france.
Since few days my dataconnection gets lost, when I try to use it. For example when I start Messenger and try to login, TP2 connects then it says Dataconnection is not available check your connection settings. After several attempts it connects stays stable for one or two minutes then again connection breaks down. I also tryed to reset the data connection via connection-wizard, nothing helps. I think something in the registry is messed up...
I don't want to do a hardreset and install all the programs again. Does someone have a good advice for me?
My Rhodium is the same situation. I am a Japanese, and mopera of Docomo is used.
[Understand now]
Cellular Line IP address & Default Gateway is same.
Primary DNS & Secondary DNS is active. I receive PING.
I can't receive PING form other site (mail server etc).
I did hardreset. But my Rhodium is not connect to Internet.
It investigates for a while. If you have good idea, then advice to me.
Same here with MTS Serbia.
I check data connection settings and all adjustment are same like automatic configuration setup but i cant get back data connections.
Hello every one.
I have understood the cause of this problem.
Perhaps, every one set WiFi's DNS server at manual.
If it's possible, set DHCP. Then DNS server is active and you can get e-mail and you can access to Internet.
I think this problem is WM network access process.
I will not use DHCP. I research other process for GPRS.
Thanks msaf, your advice resolve my problem!
I set WiFi's DNS server at manual and when i set on default i got gprs connection again
Hi,
This is an unusual problem as the wireless network card shouldn't have anything to do with GPRS!! Anyway, it seems having automatic DNS for wifi does solve the problem of GPRS but my Wifi connection will not work unless I specify the DNS manually. Therefore, it is a hassle to change between these 2 options whenever I need to change between WIFI and GPRS.
Any way to fix this once and for all??