artemis can't answer calls! - P3300, MDA Compact III General

Hi I have had this phone for just over a month and sometimes when it rings I can press a key to answer it but sometimes it will not respond. I have tried using both hard keys and the screen buttons but it won't answer the call! Sometimes it then launches co pilot instead! I have tried a soft reset but it has not worked. It is on o2 and I have tried thier data support but they are USELESS!!! all they offered was to send it off for repair (which will take two weeks!) any advice greatfully recieved.

Do a hard reset - look in the manual or wiki on how to. Something has got corrupted and this is the best way to fix. Backup you data and pim first.

Software conflict for artemis using co pilot
Hi, i tried taking out the sd card and removing the co pilot software from the phone. I then tried ringing the phone. It worked fine so I have reinstalled the co pilot and will see if it works OK over the next few days. Has anyone else had this problem and if so what causes it? cause I want to stop it happening again. Is it corruption or software conflict?

Related

My new xdaIIs locks up about 5 to 10 times a day.

I just had to have my old xdaII replaced with the XDAIIS. Im not sure this is a good thing. I felt a better replacement would have been the XDAIIi , but the insurance wouldn't go for it. After getting it, I found it to be better than expected. I didn't like the keyboard feature at first and still havn't used it. I can say it does have a pretty blue lighted keypad, which I will probably never use.
What I don't like is the fact it locks up 5 to 10 times a day and has to be reset.. There seems to be no reson for this. I do use the old xdaII case, which might come in contact with some of the buttons ( not sure) probably not. I have ordered a new hard case that is made for this pda, in hopes this will solve the problem.
Has anyone else had this lockup problem???
Dave
David Vinyard said:
I just had to have my old xdaII replaced with the XDAIIS.
<snip>
Has anyone else had this lockup problem???
Dave
Click to expand...
Click to collapse
Have you loaded any other apps or today screen plugins etc?
Is it a vanilla device that is just locking up?
You'll get lots of people teeling you it's the O2 software - but mine works fine with it running.
I had exactly the same problem. The device would usually hang while I was using Wi-Fi or GPRS, and I'd have to reset at least 3 or 4 times a day.
The o2 active software constantly monitors the status of these types of connections, and is most likely the culprit. Believe me, you are much better off without it.
After removing the o2 software I've not had to reset device at all. Just disable the o2aui today plugin by unticking the item in the Today settings dialog. You'll also need to delete the shortcut called Connections in the \Windows\StartUp folder.
Let us know if this helps with the lock-ups.
-no1
how to remove the O2 software.
thanks very much

Help, soft reset when the phone does not work at times

:? my qtek9090 phone since ive got it about 4 months ago, i noticed that the phone sometimes does not work properly. Sometimes the other person on the other line cant hear me, nor at times as well i cant hear the other person on the other line. I have to soft reset the phone always when this happens. Is this natural?
P.S. I love this phone but sometimes its annoying. :evil:
Welcome along - the Blue Angel does this - rather than a full reset turn the BT On then OFF and you will find the audio works next time you need it - pain but far quicker than a reset - The new O2 ROM download does seem to cure this problem I have run the O2XDAIIs for five days with no lockups since loading the new ROM so perhaps they have sorted this out - Mike
Thanks
Thanks mate, i guess ill have to live with it. I like this phone as it is very useful to my work and studies. Though a pain in the ass when going out with friends on parties. :wink:
:?: (My problem is im in orange, and not an O2 customer, do you think it would work?)
i'm using o2 rom on a pda2k, no problems :lol:
i'm using O² asian ROM on my MDA III works fine...

Replacement Vodafone V1620 problem

This is my second V1620 in about three weeks: the first replacement was after about nine months because the SD card slot stopped working. The replacement suffered severe touchscreen drifting and needed alignment every five minutes so they swapped it for me.
No complaints about Blue Angels or Vodafone: here's my problem. I use SPB Backup and am very careful about this to restore my system so that TomTom continues working OK. However after restoring my system today I find that TT (Navigator 5.21) is now coming up with a different device ID than before so my continuity is broken.
Does anybody know why this would be? I have checked the ROM version and there is no change there, although I am in desperation about to flash using the same version. I have no logical reason to this but I am clutching at straws!
All suggestions gratefully received, and many thanks in anticipation.
Jonathan
Strange.. My Vodafone v1620 has a deviceid of PH20B2, check if yours is like this, using GetDeviceData
Thanks xan, that is quite correct. The thing is that every pocket PC generates an unique system ID every time you do a hard reset. This is stored in software and can be overwritten by restoring a backup. In this way programs that are keyed to that ID such as TomTom will continue working even after a hard reset. If you do not take a complete backup, using Activesync or any other tool, then you would find that they stop working which is the situation in which I find myself now.
The strange thing is that I have made hard resets and restores many times over the months without a problem, hence my appeal for help!
Do you know where this id is stored?
No idea, I'm afraid. All I know is that if you make a full restore then it reverts. I believe that it may be referred to as System ID or SID as under W2K and WXP.

8525 freezes, soft reset, then "No GSM"

Recurring 8525 problem since upgrading to WM6 ROM (AT&T version). The phone will freeze completely (clock doesn't advance, screen and buttons and keyboard don't accept input, display freezes at on or off). When restarted by soft reset, the phone will frequently come back up with no GSM. When that happens, sometimes if I remove the battery and leave the phone off for a few hours then GSM will come back and will work for a while and then lock up again.
When it comes back with GSM service all of the network logon info for GPRS, my Wi-Fi networks with their auth info is gone.
Also email accounts are gone from the account picker and can't be re-created with the same names even though they have completely disappeared. I assume the settings are still in the registry but accounts just aren't showing. One account still shows on the Today screen, but isn't in the account picker.
A hard reset "fixes" things for a while. I've experimented with only installing a few of the most necessary 3rd party apps, without finding any "smoking gun" program that's causing problems. I've also re-seated the SIM card multiple times. I'm thinking it might be a hardware problem.
Today I flashed the radio to 1.54 and it has worked for a couple of hours without needing to be reset.
I'd be interested to hear what possible diagnostic paths I should look at before I call AT&T and begin the rigmarole required by tech support. Anyone with a very similar situation?
Thanks in advance.
I'm having the same problem. I was thinking of going to AT&T to get a new SIM, thinking that was the problem. Any solution yet?
-Pete
I started having the same problem with mine last week.
Sometimes it locks up, sometimes it gets stuck at the windows logo durring boot, always displays no gsm rom on boot.
Take a look at the how to unbrick thread. no gsm rom msg is one of the types of brick.
I installed hard spl ( already had it actually ). Flashed os, but it didn't help. Flashed GSM and no gsm msg went away. The phone is still acting strangely.
remember, just because the rom came from your carrier DOESNT mean that it doesnt have problems. Alot of people seem to have problems with upgraded rom versions from their carrier and end up either downgrading to previous rom or flashing cooked roms. try the previous rom or another cooked rom and see if that fixes the problem before blaming the hardware. It will save you a major headache trying to troubleshoot something that is working perfectly....
Please remember to do a bit of reading and hard spl your device before going off and bricking your Hermes. 10 minutes of reading might prevent hours, days or weeks of hair pulling, nail biting insanity to find the answer. Cheers.
hello people,
I have my SVP M3100, original from orange spain - but CID unlock to work with portuguese carrier, now I live and work in Hereford UK, and I use a sim from Three and other from Lebara the three sim is to have net on my pc and the lebara sim is to make low cost international call, and i switch many times the sim's to make calls and to have internet, now i have the same problem that you have, i try to upload the HTC original rom that have IPL. BOOTLOADER, SPLASH SCREENS EXTROM GSM, but lock at 12% I try upload ongly radio rom and the same a think that somekind of hardware problem caused by to many sims switch, if any body have one solution please tell me
Sometimes it locks up, sometimes it gets stuck at the windows logo durring boot, always displays no gsm rom on boot."
Same thing happened to me. Tried to reflash original ATT ROM , Radio Only, OS only. Gonna send it for the repair. Phone is not under warranty anymore hope that the price of repair will be less than price of new phone.
BTW, is there any way to remove Hard SPL from the phone?
how much was the price of repair?
Try changing you radio to a new one. i have had the same problems in the past with different radio roms and rom versions. so i am using radio 1.54.30.10 with pdavet roms and have had no isuue.
Ray_jai said:
how much was the price of repair?
Click to expand...
Click to collapse
Got my phone back fixed. They charged me for shipping only $19
only $19!?
What if I don't have ATT anymore?
do you know?
i had the same issue check for my previous posts i think no GSM is a common error there is method flashing himalaya rom on hermes to erase GSM sector.
if you cant find the link PM me .
i hope it solves your problem.
tracylynnt said:
Recurring 8525 problem since upgrading to WM6 ROM (AT&T version). The phone will freeze completely (clock doesn't advance, screen and buttons and keyboard don't accept input, display freezes at on or off). When restarted by soft reset, the phone will frequently come back up with no GSM. When that happens, sometimes if I remove the battery and leave the phone off for a few hours then GSM will come back and will work for a while and then lock up again.
When it comes back with GSM service all of the network logon info for GPRS, my Wi-Fi networks with their auth info is gone.
Also email accounts are gone from the account picker and can't be re-created with the same names even though they have completely disappeared. I assume the settings are still in the registry but accounts just aren't showing. One account still shows on the Today screen, but isn't in the account picker.
A hard reset "fixes" things for a while. I've experimented with only installing a few of the most necessary 3rd party apps, without finding any "smoking gun" program that's causing problems. I've also re-seated the SIM card multiple times. I'm thinking it might be a hardware problem.
Today I flashed the radio to 1.54 and it has worked for a couple of hours without needing to be reset.
I'd be interested to hear what possible diagnostic paths I should look at before I call AT&T and begin the rigmarole required by tech support. Anyone with a very similar situation?
Thanks in advance.
Click to expand...
Click to collapse
I've got exact the same symtoms. No GSM, network and auth settings gone, opera registration lost etc. It started a few days a go, in the beginning I had a working GSM most of the time, but it became less and less and now it doesn't have service at all anymore.
Currently device information shows:
ROM version: K's Rom v1.21
ROM date: 10/03/07
Radio version: NONE
Protocol version: NONE
Model No.: HERM300
IMEI: <empty>
Does anyone know a permanent solution?
I have the SAME PROBLEM!
I was about to get radio to work 3 days ago, and now the radio says none.
it's like the radio removed itself.
ok this doesn't make sense, I used the hima rom to remove the radio.
and now the radio is back! wtf?
Hm I tried everything but I can't seem to reflash the radio. About every version I try hangs at 0%. Sometimes when I flash from SD card it hangs at arount 10%.
Tried different SPL versions as well
Damn you radio!!!
BTW, I have no idea what they did to my phone there, but after returning from the AT&T Repair center the Call timer was zeroed and Device ID is now different from what it was before in Skyscape software
Any solutions yet? Im having the same issues.
The reason why Active Sync restarts
For many people the Workaround "not a hack or registry at all" does not work is because of a event based notification that runs the program anytime the time changes. Since your phone updates from the cell tower, it updates the time alot even if by mere seconds well this update runs activesync. Get yourself MemMaid
run it in advanced mode then Jump to Databases then select Notification Queue you will see a list of 3 types of Queues; Time Based, Classic Time Based, and Event based. Go to the event based queue, you should see at the end of this list 3 listing for repllog.exe with the active sync icon. Click on them individualy and read what shows up in the window below put a check mark next to the listing that describes the event as "apprunaftertimechange" it is normaly the last one on list
Also make sure there is no repllog.exe listed in any other queue for a time based event. Leave the other instances of repllog.exe since you still want your device to sync when its connected to the computer. Once you select all events that desribe running repllog.exe after a time change or at a certian time and date press the delete button.
This worked for me on my 8125 and the tilt and if i would of figured this out before i had ATT replace my 8525 i probably would of not got the tilt but lol they gave me tilt free cause all the problems i had with 8525.
let me know if this works for you guys that still see activesync running after the fake server WORKAROUND.
This should work
memmaid is not free but i think its free to try and if all you do with it is fix this problem then great or find a way to register it cause it does help has cool tricks and tweaks
Wow, still no real fixes for this problem, bummer
running memmaid work
running memmaid works and fixes the random start of activesync and once the random start of activesync is fixed the device will not lock up because of activesync this not to say if some other program you may have installed locking you up as well

help, need a creative hard reset procedure or something

I've read the wiki and faqs beforehand. Now, with that out of the way here's my issue. I need to either hard reset or reinstall a new rom on my t-mobile branded dash. Here's the constraints
1) left soft key doesn't work, but all other buttons do.
2) I can't activesync and I've never synced the phone to a computer before.
That's it.
I recently posted a couple questions because the phone got oil damage and wouldn't start up. Well... i fixed that, but for some reason when booted up, it automatically locked the keys. I would normally click left soft key and * , but of course... left soft key doesnt work. Therefore, a traditional hard reset won't work, and if it could, well... i'd just unlock my keys right. Since this was my mothers phone, i never needed to sync it and I tried syncing a few minutes ago and get nothing. That's probably because the phone is locked.
The phone is carrier unlocked and runs on att network.
Common guys... need your help on this one. Either a way to unlock to keys or a way to hard reset would be good... as long as the hard reset doesn't result in a fresh os that starts up with keys locked.
Look below and download the new 6.1 Rom and then navigate here on how to set up the rom. http://forum.xda-developers.com/showthread.php?t=415225
Follow those instructions and it will work for you.
well thanks, but step 1 is not possible. In my original post, i mentioned that i can't sync because 1) the phone has never been synced before and 2) my comp, which already has activesync installed for my hermes, doesn't recognize the device in the usb port.
Yeah dude, can't even run the sda unlocker man. It asks to connect my phone. Whats up on an old school sd rom install.. oh yeah, that violates the first law.
So, there seem to be two rules. No left soft key and no activesync. HELP?
im me if you think you can help
[email protected]
remote hard reset
ATT says that they can remotely do a hard reset from their corporate fortress of pain and suffering. I will allow them to rape my data stream in an effort to free my soul of the keylock demons. I will have plenty of holy water... so don't you worry.
Maybe try a program like my mobiler or True Connect Pro. You could possibly put the cabs on your SD mini card and control your mobile thru your pc and clear your storage to hard reset. Your probably still going to need active sync but do your research just to be sure.
Honestly I think your phone is fubar. If you spilled some oil inside it and buttons are not working it's only a matter of time where more problems will occur.
Good Luck
your right... it had a good 2 week run after the oil spill. Now, even though yesterday it was charging and starting fine, today it wont charge or start. Oh well... i give up.. anyone need a new battery?

Categories

Resources