Related
Hello everyone.
I have just bought my Hermes (AT&T 8525) after one year of planing so. It came with WM5. I downloaded some of the ROMSs, radio and bootloaders commented here. I tried reading all the vast infromation in this forum and the wiki, but still having a problem.
THE PROBLEM IS AS FOLLOW:
When I start the flashing process, using HTC_TyTN_WWE_3[1].54.255.3_6275_1.48.00.10_108.exe or RUU_Hermes_CINGULAR_WWE_3.1.57.502.1_6275_1.48.00.00_108
... everything goes well, until the progress bar appears in my PC. When it appears, ActiveSync in my PC closes and my Hermes goes to stand by (the lcd goes off) so I cannot complete the installation process.
The phone works pretty well and I'm really amazed for all its capabilities. But still, I'm stucked with wm5.
Why do you think this happened?
PS: I flashed the radio (1.51.00.10) and bootloader (HARD SPL v7). My ROM version is 2.15.502.3. I use "ActiveStink" to sync my files without problems.
Any advice will be more than welcome!!
I'm no expert but that appears to be normal behaviour!
ActiveSync is only used at the start of the process. After a few files have been transfered, Activesync is closed and a different link is established. If you just leave it for a short while longer, a progress bar should appear on the Hermes too.
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
todd_jg said:
Yes, ActiveSync will disconnect. The RUU takes over the connection. Have you let it sit - sometimes it takes a minute for the progress bar to move.
Have you consulted www.mrvanx.org for help on the flashing?
Click to expand...
Click to collapse
I'm having the same problem - always have. The message tells me that I'm disconnected and that I should check my USB connect etc. I left that box up there for about 15 minutes. Now I've closed the box and have waited several minutes with no activity. This is pretty aggravating. Thanks for any help.
try turning off your antivirus aplication. thats work for me flashing my tytn to wm6.
I've done everything.... I guess
Hi...
Yes, I consulted the www.mrvanx.org, excellent tutorials.
I flashed without problem the radio and bootloader. The progress bar started to "progress" and everything was fine. The only problem I have is flashing the WM6.
I don't remember where, but I readed that flashing the bootloader "Hard SLP v7" causes my HTC not to accept any Oficial WM6 ROM. The article said that I only had the chance to flash a coocked or modified ROMs. Is this true?
If not... what else can it be? I also closed all my applicacations including the antivirus, goback, disabled the internet connection, the logictec mouse center, etc. and nothing, the same as Chicoh happens to me.
"Error 260: Connection... check the USB cable bla bla bla."
Should I restart in safe mode to do the flashing?
Should I try to install a modified ROM?
Have in mind I've tried three different official ROMs: WWE, Cingular and spanish.
Thanks to all the comunity!!!
Saludos desde México!!
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
liquidsilver said:
Greetings -
I had a similar problem and couldn't get the thing get going. My solution was to load it from the SD card. This worked flawlessly.
Click to expand...
Click to collapse
I'm trying that as we speak. I have a good feeling about this. I'm a little concerned that I didn't think of it though. Makes perfect sense - Skip the middle man.
UPDATE: Crap. No luck. Thanks all the same though. I'm not giving up.
What OS are you using, xp or vista? My vista 'top had the same problem wouldnt flash for the longest time and i had to use my xp.
However, it does work now. Not entirely sure why.
Now I had success!!!
Hello my friends.
It seems that the article I readed days ago detailing that after flashing the Hard SPL v7, I could only install a modified ROM, not an official one from HTC or Cingular.
I downloaded Black Satin and installed it without any troubles. The entire process lasted only 3 minutes!!!
I wanted to have an official ROM, don't ask me why, and never tried the "other" ROMs that are actually excellent!!! some apps that were on WM5 are not in WM6, which is kind of sad, but if there's something that I love of WM Smartphones is that I can download and install whatever I want or develop it if it doesn't exist!!!
By the way, I use Windows XP Pro.
Thanks for all the support!!!
PS: Before flashing the Hard SPL v7, I tried installing the cingular WM6, but didn't make it. That's why I readed almost all the pages and threads here in xda-developers and found that flashing a new bootloader was a very good idea. The rest of the story is known by you.
Step 1 hard reset.
step 2 connect and sync
step 3 run USPL from standalone, O2 Premium 2.0 Full or Artemis Touch 3.01 full
ALL fail.
get black screen with linux icon green wrighting then it goes black.
actuve sync icon goes white.
Only way to restart is take the battery off and reboot.
Any help
Using a 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 2.67.90
OS 3.4.0.0 i think.
thanks James.
Make sure your battery is over 50%!
Mine did this a couple of times... do a hard reset, then uspl.
TangerineTractor said:
Make sure your battery is over 50%!
Mine did this a couple of times... do a hard reset, then uspl.
Click to expand...
Click to collapse
Batt FULL
done 2 hard resets ?
done it 3 or 4 times ?
Exactly same problem here. Screen goes white, loses activesync connection and never comes back. I do then get the Windows 'Found New Hardwarde' screen, so am thinking this is more to do with the XP setup. Will try at home later!
Using a WM6 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 02.67.90
OS 3.4.0.0
fleggsy said:
Exactly same problem here. Screen goes white, loses activesync connection and never comes back. I do then get the Windows 'Found New Hardwarde' screen, so am thinking this is more to do with the XP setup. Will try at home later!
Using a WM6 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 02.67.90
OS 3.4.0.0
Click to expand...
Click to collapse
At least im ont alone or
gingerr6 said:
Step 1 hard reset.
step 2 connect and sync
step 3 run USPL from standalone, O2 Premium 2.0 Full or Artemis Touch 3.01 full
ALL fail.
get black screen with linux icon green wrighting then it goes black.
actuve sync icon goes white.
Only way to restart is take the battery off and reboot.
Any help
Using a 02 xda Orbit.
IPL 3.04.0001
SPL 3.04.0000
GSM 2.67.90
OS 3.4.0.0 i think.
thanks James.
Click to expand...
Click to collapse
Hi gingerr6 and fleggsy,
I had a similar problem with the USPL program.
My work around was to use one of the USPL'S included in the many rom's posted here on XDA-Developers, so I used the artemis vanilla 2.01 supplied USPL and it works fine.
I have removed only 1 files to cut down on the file size, i.e I removed the artemis_vanilla_2.01_WWE.nbh main file (53.960Mb).
Use this only to USPL your device, it wont flash the vanilla 2.01 rom as the file is removed.
Hope this helps you both.
Just run "STEP 1 - activesync then uspl cid unlocking.bat"
http://rapidshare.com/files/89152338/Artvan2_uspl.zip
NOTES:
1-Make sure you remove your memory and sim card before flashing.
2-Make sure your PDA is fully charged.
3-Make sure that active sync (or windows mobile device centre in Vista) see's your PDA first.
remove the memory card and try again.
gadjet said:
Hi gingerr6 and fleggsy,
I had a similar problem with the USPL program.
My work around was to use one of the USPL'S included in the many rom's posted here on XDA-Developers, so I used the artemis vanilla 2.01 supplied USPL and it works fine.
I have removed only 1 files to cut down on the file size, i.e I removed the artemis_vanilla_2.01_WWE.nbh main file (53.960Mb).
Use this only to USPL your device, it wont flash the vanilla 2.01 rom as the file is removed.
Hope this helps you both.
Just run "STEP 1 - activesync then uspl cid unlocking.bat"
http://rapidshare.com/files/89152338/Artvan2_uspl.zip
NOTES:
1-Make sure you remove your memory and sim card before flashing.
2-Make sure your PDA is fully charged.
3-Make sure that active sync (or windows mobile device centre in Vista) see's your PDA first.
Click to expand...
Click to collapse
Have not removed my sim so i will try that.
will dowload and try the attached file, thanks
right PDA?
i have the 02 xda orbit.
i take it the is the right forum and it is a HTC Artemis ?
just checkin LOL.?
gingerr6 said:
i have the 02 xda orbit.
i take it the is the right forum and it is a HTC Artemis ?
just checkin LOL.?
Click to expand...
Click to collapse
Yes the device is know by many names, take a look here for all the details you require.
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis
gadjet said:
Yes the device is know by many names, take a look here for all the details you require.
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis
Click to expand...
Click to collapse
FANTASTIC thanks.
gingerr6 said:
Have not removed my sim so i will try that.
will dowload and try the attached file, thanks
Click to expand...
Click to collapse
NOPE !!!!! followed ALL advise still not working ?
I must be doint something wrong ?
James.
Gadjet / mr.valacky - thanks for your time guys, but I'm afraid I still have to side with gingerr6. The problem is the same on all machines. The screen goes white and the active sync connection gets lost.
Have tried without sim and memory cards on my work PC running Win XP and my home PC running Win XP. Also tried on my Vista laptop but understand that there may be other issues there with Windows Mobile Device Center.
There is only 4mb of space on the phone currently, but would this matter if it's gonna get wiped anyway?
Haven't tried your artemis vanilla 2.01 yet Gadjet, plan to today when I get a few minutes.
Cheers!
See attached
have followed all information
even changed then usb cable.
this where i get to see attached.
is this right and if so how long should it take ?
also what happens after this does it load windows back up and then you flash from there or do you flash from this screen ?
Many thanks James.
In my limited (not fully working) experience James, it stays like your screenshot for approx 5 seconds, and then the whole screen goes white and this is where I lose activesync. It may go blue at this stage apparently (which is also ok) but as long as you have your activesync connection you can then proceed with the flash of the USPL and then the ROM of your choice.
fleggsy said:
In my limited (not fully working) experience James, it stays like your screenshot for approx 5 seconds, and then the whole screen goes white and this is where I lose activesync. It may go blue at this stage apparently (which is also ok) but as long as you have your activesync connection you can then proceed with the flash of the USPL and then the ROM of your choice.
Click to expand...
Click to collapse
YERRRRRRRRRRRR !!!!!
done it
mine went black, and lost active sysn icon but you carry on and flash with rom 9.99 or something will update to 100 VERY quickley.
then it restarts and you will see the SPL has changed to 1.1.000.000 or something, then once in windows active sysn and flash the rom .
mine is working GREAT , all be it only up fot 2 mins
Gadjet, tried the vanilla uspl too and this has exactly the same results for me. Oh well, just have to keep factory O2 WM6!
fleggsy said:
Gadjet, tried the vanilla uspl too and this has exactly the same results for me. Oh well, just have to keep factory O2 WM6!
Click to expand...
Click to collapse
Hi gingerr6 and fleggsy.
I have had that happen to me loads, and my only way was to hard reset and try again.
Hold down the 2 top hardware keys and press soft reset button. (Contact & Calender buttons)
Last night it happened while flashing the a new rom.
Hope this helps..
gingerr6 said:
YERRRRRRRRRRRR !!!!!
done it
mine went black, and lost active sysn icon but you carry on and flash with rom 9.99 or something will update to 100 VERY quickley.
then it restarts and you will see the SPL has changed to 1.1.000.000 or something, then once in windows active sysn and flash the rom .
mine is working GREAT , all be it only up fot 2 mins
Click to expand...
Click to collapse
Congratulations gingerr6. I tried just going on but without an activesync connection, it tells me it cannot connect to my phone.
fleggsy said:
Congratulations gingerr6. I tried just going on but without an active sync connection, it tells me it cannot connect to my phone.
Click to expand...
Click to collapse
take out memory and sim do hard reset sync and try and use start_uspl.exe
not STEP 1 - active sync then uspl cid unlocking.bat in Artemis vanilla 4.01
thats how i did it
don't worry if the sync logo goes white or disappears just carry on the 1 st step to change the SPL after it restarts you will see it on boot up but it will boot into your old ORIGINAL rom.
now run step 2 this will update the rom
I am very frustrated with my HTC Touch Diamond as I am trying to update it to Hard-SPL yet when it's plugged into the computer (with active sync running) and I follow all the directions very closely, I go to update the phone and it doesn't show any activity on the phone, the progress bar on my computer screen shows 0%, then it eventually pops up with a message saying Error 202. This is a connection error, yet I am positive that the phone is plugged into the computer. Please HELP!
Hello, Did you run SSPL first? You can only flash hard spl when sspl is active it is a black screen.
I have a Telus HTC Touch, does that make a difference on whether or not this will work?
your diamond is cdma. these only work with gsm.
so by the word 'these' in the last post, you mean that the Rom updates won't work?
I don't think SPL has to do anything with CDMA or GSM. Some ROMs have an option in the phone settings to choose either GSM or CDMA.
ryanseyz: Make sure you have a factory ROM ready before trying the cooked ones here so when things happen unexpectedly, you always have a choice. Next, there are 2 versions of SPL here, try both. Make sure you install EnableRAPI.cab and CertSPCS.cab installed on your device.
Regards,
Carty..
anyone has a solution for this yet? I'm experiancing the same problem with my Touch Pro, can't seem to get it to work.
I installed both files like mentioned above but still give error 202.
The funny thing is it does recognize the current version of my rom (stock).
Greetings,
Phyrax
Phyrax said:
anyone has a solution for this yet? I'm experiancing the same problem with my Touch Pro, can't seem to get it to work.
I installed both files like mentioned above but still give error 202.
The funny thing is it does recognize the current version of my rom (stock).
Greetings,
Phyrax
Click to expand...
Click to collapse
The same here with my mda compact iv. I've tried all versions of the RUU of hardSPL with no result (error 202). When I update the official rom of t-mobile (1.93) with the RUU, there isn't a connection problem and everything goes well.
My device is not simlocked, but i suspect it has a security lock or something like that.
Hello, I have the same problem with a HTC Diamond : error 202 and everything is connected, hotsynched, etc.
Did anyone find a solution ?
anyone??? im having the same problem..
I'm having this issue as well, any solutions?
The same problem
I have a HTC Touch Diamond and have the same problem.
I don't know what i have to do to fix this problem.
I have got the same problem. Add I have problem with align screen, so I can't run any cab on device. Looking for any advice..
i have a htc mda basic ....same problem...any solution...please help....
I'm not sure, but if i'm not wrong i had the same 202 error code last time i tried to reflash original (stock) spl, for warranty reasons. I solved the problem flashing stock spl (from hspl 1.93 olinex) with the phone conencted to activesync: run sspl-manual.exe from the device (previously copy sspl-manual on the device): the phone will go to black screen; than run the normal romupdateutility.exe from pc, and follow ordinary instructions.
Hope this could help.
Dudubai said:
I'm not sure, but if i'm not wrong i had the same 202 error code last time i tried to reflash original (stock) spl, for warranty reasons. I solved the problem flashing stock spl (from hspl 1.93 olinex) with the phone conencted to activesync: run sspl-manual.exe from the device (previously copy sspl-manual on the device): the phone will go to black screen; than run the normal romupdateutility.exe from pc, and follow ordinary instructions.
Hope this could help.
Click to expand...
Click to collapse
Thank's..., this solution work for me...!!!
For me too !!! working now !
Thanks it work!
Thanks !!! It works !!!
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
ETUMON said:
PLEASE ASSIST: I'VE RECENTLY UPGRADED MY CINGULAR/ATT 8525 HERMES UNIT TO WINMOB6 AND NOW CAN'T GET PAST THE INITIAL WINDOWS MOBILE SCREEN WHERE IT SAYS "TAP THE SCREEN TO SET UP YOUR WINDOWS MOBILE BASED DEVICE." (THE TOUCHSCREEN SEEMS TO BE DISABLED) ALSO, NOW ACTIVESYNC WILL NOT CONNECT TO THE DEVICE. I'M AT A LOSS AS TO WHAT ELSE TO DO (TRIED HARD RESET SEVERAL TIMES WITH SAME RESULT). IF SOMEONE COULD POINT ME IN THE RIGHT DIRECTION - I'D SURE APPRECIATE IT.
Click to expand...
Click to collapse
hmm no need to scream.
Push the OK on left and power on right, and stick stylus in all at the same time. Re run the exe file while it is plugged in to active sync, and see. Which WM6 did you use?
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
ETUMON said:
Sorry I'm new at this. I used WM6.1. Which exe file do you want me to re-run. ActiveSync is offline....I can't get it to connect to the unit. Thanks for your assistance.
Click to expand...
Click to collapse
Ok, since you're on ATT I suggest you follow my instruction above, get into tricolour screen (bootloader), and download this
from the post above you will get the shipped ATT rom. Don't worry if activesync is saying is not connected, just run the file. You will then get back to a WM6.
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
ETUMON said:
The phone originally came with WM5 and I was upgrading to mess around with the thing. I'm at the tricoloured screen and now downloading the files from RapidShare. Will this get me back to WM5 or to the upgrade. If there is a way, I like to try the HardSPL flash I've been reading about today - will this work on either WM version? Txs & Rgds.
Click to expand...
Click to collapse
After you have flashed this WM6.0 you really need to flash hard SPL first, I thought you would have done that already.
Really please read this first before you brick your phone.
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
ETUMON said:
No that's the thing. I'm just finding out how I went about this all wrong and maybe shouldn't have been messing this in the first place. Anyhow, my bootloader screen reads like this:
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
Click to expand...
Click to collapse
Well follow mrvanx guide, that's all I had to get on with few months ago.
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
ETUMON said:
Many thanks for the advice. So just to be clear I should first run the file I downloaded from RapidShare to get me back to a working WM version, then follow mrvanx guide to flash Hard SPL or viceversa...
Click to expand...
Click to collapse
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Still Stuck
zocster said:
I have not tried to hardspl a non working phone sorry so I have no experience with that. Give it a go first, and report back.
Click to expand...
Click to collapse
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
ETUMON said:
Nope, didn't work. Here's the report:
ERROR [260]: UPDATE ERROR
The update utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
Is there another way to establish comunication with the PDA other than through ActiveSync? Somekind of emulator box or binary software???
Click to expand...
Click to collapse
hmm weird, so have you got .net framework installed on your PC? try it again one more time while in bootloader, plug the phone to USB as long as you can hear the 'ding' sound you should be OK. I have 'bricked' my phone a few times and this always work. What are you trying to flash? the hardspl or the ROM?
Yes, today I upgraded to .net framework 3.5 when ActiveSync failed Microsoft Error took me to their website and offered me the option. I had been running 2.x .net framework and never had a problem would also use same ActiveSync with my old Axim X30.
Yes, I can hear the 'ding' sound and I was trying to run the file RUUWrapper.exe (Hermes ROM Upgrade w/ the option Force using SSPL).
well that shows the other way around doesn't work, so you need to get your phone to a working WM6 state, how is your download going from rapidshare? get it to boot loader mode again and flash that exe file.
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
ETUMON said:
Just completed that route - I ran the PDA Phone ROM Update Utility 3.12.3.7 - the process took about 10 minutes to go through 100%, then it restarted and stayed at the Window Mobile screen for little over minute (crossing my fingers), but then just showed the same message "Tap the screen to set up your Window Mobile based device." Please let me know if you have other avenues to try – It’s close to 4am here in Miami, but I'm not sleeping. I’m really glad you are able to assist with this mess – thanks a lot!
Click to expand...
Click to collapse
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
zocster said:
so did you follow it through? and it didn't fix it? you have some bad blocks?
Unfortunately, you need to have some sleep, and read these when you wake up
http://forum.xda-developers.com/showthread.php?t=296722
http://forum.xda-developers.com/showthread.php?t=369434
Click to expand...
Click to collapse
what does bad blocks mean?
Okay, looks like I've got a Type 2c Brick Situation in my hands.... I think I will take your advice and get some rest and tackle this again later on. I really appreciate your assistance - will you be around again later?
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
ETUMON said:
Okay good day, I'm back on the trail. Found shipped ROM on WIKI for HERMES in the following thread - http://forum.xda-developers.com/showthread.php?t=277664
Downloading now...According to pof(moderator) it's a "new rom from the still unreleased Cingular 8525: HTC Hermes (HERM100) branded from U.S. Operator Cingular"
My only question then would be that this appears to be made for WM5 and I performed the WM6 upgrade which is what got me into this mess in the first place - so will there be any conflicts or issues I should now about? I'm about to go ahead with it - if anyone is out there and thinks otherwise, please advise soonest. Thx & rgds, Ed
Click to expand...
Click to collapse
Sounds good man!! Flash it!! oem WM6 roms usually fix allot of issues.. Don't be scared everyone else is busy flashing WM6.1 roms all the time now!
Thanks for the words of support <joshkoss>! Just attempted several times to flash the Shipped ROM I found from <pof> (PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0) and keep getting ‘ERROR[260]: UPDATE ERROR’ message. While instead I went back again to flashing the ROM that <zocster> suggested last night (PDA Phone ROM Update Utility 3.12.3.7) and it does go through the entire 10 minute process until it shows 100% completion both on the PDA and on the PC and then tells me congratulations….etc. I even flashed it twice back-to-back as I read to do in one of the threads – but just keep getting back to the dreaded Window Mobile screen with the same message "Tap the screen to set up your Window Mobile based device."
My next question is this: Why does the PDA Phone ROM Update Utility 3.12.3.7 connect to the PDA, but the PDA Phone ROM Update Utility - R:31300 D:51000 U:31101 P:0 (which I read is the Shipped ROM that I need to get the PDA back to) gives me an error message. Obviously, there is a connection since I’m able to get a 100% completion on the other ROM??? Please kindly advise…..
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
I had what sound like the same problem yesterday.
my post is over at ppcgeeks.
"I disconnected but I did not see the phone exit bootloader mode and reset itself.
....
What should I do from here?
Reboot phone, soft reset, hard reset? - go have fun?
....
I did a couple soft resets and have been playing around with it,
I guess I upgraded right... but it was weird there at the end, instructions not the clearest to me, i guess."
mine seems to be working fine, except the weather thing.
shows
in the About section my phone reads
WM 6.1 Pro
CE OS 5.2.21041
Device Information reads
ROM version 1.05.Alltel
Radio version 3.42.30
PRL Version 30008
PRI version 2.02_011
I was kinda scared to do another hard reset b/c I had already changed a bunch of settings.
Sorry if this doesn't help you too much,
but it is nice to know I'm not the only one with this issue
.
Hmm sounds like a similar problem. But I thought it wasn't unlocked unless we saw 2.31.coke somewhere in the device information.
As far as I know, hard reset did not hurt the phone. I tried installing that unlocker 4 times then went with the original HTC rom and it still turned out just like before. It installed the rom fine
Yeah I am still concerned about how it wont go through the exitbl step...
moonwoo said:
Hey guys I know this is not the unlocking thread but I tried posting on the thread made by "coke" with no response. So I thought I'd do it here. So here's the story
I have a Sprint Vogue and I was really getting tired of the slow HTC WM 6.1 and all the buttons that I could not modify on the cube (which is useless cuz I dont use any of the them). So I decided to try out a new rom with 6.1 and touchflo 2D.
I went to the ppcgeeks forum to unlock the phone, followed the instructions, read and reread the posts. Finally decided to give it a go. Everything went smoothly until the last step (exitbl) of coke 2.31. It kept telling me to disable USB on activesync and then the program would just shut down! ?? And yes I did disable the USB option for the activesync before that step. I looked under the device information and realized that nothing has changed interms of the ROM. So I tried it again and again (4 times). Then I just reinstalled the HTC 6.1 rom with the 3.42.30 radio... So any ideas on why this may be happening? I promise I followed all the steps
My second question is, in your opinions, what is the most reliable, stable and fast Touch 6.1 rom? Let me know if you have an opinion.
Thanks so much in advance, any help would be appreciated.
Click to expand...
Click to collapse
Yeah, the directions can be a bit confusing over there on that thread
Basically here are the steps
Download the 2.31 unlocker
Download the ROM you want to use (my personal preference is this one for a TF2D style or this one for a WinMO 6.5 style interface that has TF2D included to switch back and for - both very stable, fast and clean and the thread is very active for help (especially if your on Verizon or Bell which can have issues)
from there, use WinRAR to extract each file into separate folders
then Put your phone in bootloader mode (press and hold power+camera+stylus in reset until 3-color screen comes up)
At this point at the bottom of the screen it will say Serial, plug it into the USB cable or cradle and it should change to USB
Start the exe in the 2.31 and follow the directions (you may get some errors about sleep4.exe just click on OK as it keeps occuring its a XP/Windows7 64 bit issue if that is what your using)
At the point where it tell you to disconect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
once complete, reboot, allow it to do its thing then reboot and go back into bootloader again during reboot you should see coke 2.31 in the upper left if so your ready to go
plug it into your USB/Cradle again and then go into the ROM folder you extracted the ROM into
Once the screen on your phone says USB again go to the folder and double click on the RomUpdateUtility.exe file and follow the directions again, it may take some time so be paitent
once the phone flashes and reboots, let it run and do its thing to the and reboot itself then (and here is an important step for stability) once it starts up do a hard reset (red+green+stylus in reset hole) hit the enter button (center of D-Pad) it will reflash the phone and then red key (send) when prompted
then go thought the setup again, this time you can actually set things up as your keeping them this time and once things are done and your at the start screen on your phone power off (not reset) the phone and then start it up again - seems doing it this way takes care of alot of little issues that will come up before they can happen
Depending on your carrier be sure to have one of the DCD Carrier Cabs as well especially for the 6.5 ROM as it is a generic ROM and some have reported needing to run the DCD Carrier Cab for the service they use to get on the internet and use GPS and the like
Hope that clears up things a bit LOL
Detroit Doug
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
moonwoo said:
Doug, when I go into the bootloader it DOES say SPL-2.31.Coke. Does that mean that it is all set? Also this time, it still asked me to disable active sync at this time (at the exitbl step) do you have to run that step to complete the unlock?
This is what my bootloader image says
VOGU100 NFG
SPL-2.31.CoKe
CPLD-3
Let me know if I need to run the exitbl or if I am set to load the rom. Thanks so much for your help!
Click to expand...
Click to collapse
Your all set to flash if in bootloader it says as your phone does SPL-2.31.CoKe
you all unlocked and ready to go ... just put your phone in bootloader mode then connect the phone to your PC "serial" will change to "USB" and then run the RomUpdateUtility.exe file and follow along with the bouncing ball, do the watusi, wipe hands on pants - whatever helps you pass the time
but follow the steps as outlined above with the hard-resets and power-offs and the like, believe me its better to solve the issues before they occur than wait and have to start over
Detroit Doug
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
moonwoo said:
Doug, it worked like a charm. I did not know that the last step of the unlocker was not required. I installed 6.1 with Touchflo 2D. Looks and feels .. wow. it's the coolest thing I've seen. I've followed all your step including a hard reset before I started using it. So far the speed is impressive.
Couple more questions for you since you are an expert at this.
1. If I reload the factory default ROM, will it reset everything back to normal and can I keep reverting back and forth between different ROMs without any consequences?
2. It (the NFSFAN's 6.1 rom) seems to use less Storage memory (137 free vs HTC's ~100 free) but much more Program memory (59 free vs. ~80 in HTC's) than the HTC default. Any ideas or concerns about this?
All in all thanks so much! Hopefully as I learn more and more I will be able to contribute things too. You are right. This is so cool and highly addictive!!
Take care~ BTW I am in Lansing Go State!
Click to expand...
Click to collapse
Glad it worked, and Ill try to answer you concerns
1 -Now that it is unlocked go ahead and swap ROMs all you want to, the tricky part is the stock ROM, flashing back to stock can and will revert your radio (if youve upgraded it) and ca cause issues with the unlocker, but a simple run of the unlocker 2.31 again can correct it
2 - NFSFAN like other Chefs have ways of moving data/programs around when they cook up these ROMs utilizing whatever kitchen program they personally prefer that being the case how they data/programs get pushed about can create the speediness you now see in your phone by freeing up the RAM for apps and the like and pushing programs off to the side optimizing how the device should have been setup from the start
As for that, Ive been using his ROMs as well as some others for quite some time and have had little to no issues with how he places the progs and data so I wouldnt worry about it
Yeah, Live in Las Vegas now - but Michigan will ALWAYS be home Go Red Wings !!!!
Detroit Doug
Thanks Doug, for all your information. Your answers were great! Hopefully I wont need too much more help in the future. i'm learning~
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
hibbiejibbie3 said:
Don't mean to go off on a little tangent, but I find this post really helpful and was wondering if you, Doug, or someone else could provide a link to this 2.31 unlocker or whatever it is. Thanks in advance.
Click to expand...
Click to collapse
http://forum.ppcgeeks.com/showthread.php?t=20370
Detroit Doug
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
Check your PM over at PPCGeeks
Detroit Doug
Reddog80p said:
Having trouble unlocking my xv6900. I'm using 2.31 unlocker. I have the phone in bootloader mode and when I connect the usb it goes from serial to usb. I run the RUU from the unlockers self extracted folder but it get an error message. I'm pretty positive its just something im not doing correctly. Any help appreciated.
Another thing I noticed the RUU will not detect my current version if I am in bootloder mode. If I run the RUU with active sync on it will detect my current version but when it puts my phone into bootloader mode to update it, it disconnects my active sync connection.
Click to expand...
Click to collapse
From Detroit_Doug
At the point where it tell you to disconnect, unplug the phone from the USB cable and wait (count to 10 or something) then plug it back in, it should have went from USB to SERIAL and now back to USB at that point go ahead and hit any key on your PC and it should continue along
Maybe wait longer if you can,
I reckon some pc take longer to fully recognize[process] the disconnect and reconnect procedure.
example: disconnect > wait 20-30 seconds > reconnect > wait 20-30 seconds > then continue
I had that same issue and waiting longer during this process helped
.
I can't even get to that point. With active sync on as soon as I start the unlocker RUU it gets the info from my phone and shows the current rom 3.14.605.1 ....I click update and it shows 2.31 unlocker I hit next and then the install status bar comes up on my desktop and my phone goes into bootloader mode and the active sync connection drops and I get the 262 connection error. If I start the RUU with my phone in bootloader usb mode already it does not detect my current rom and I click next. click next to 2.31 unlocker, and it goes through the same steps and I get the same error. Is there anything I have to do to my phone prior to running the RUU. My phone is a verizon xv6900 running wm 6.1 rom 3.14.605.1 with radio 3.37.78
I have the same problem with my new sprint touch. I get error 262 at 0%, did they change something in these new phone that won't allow us to unlock?
Rom is 3.03.651.4
radio 3.42.30
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
I ended up having to re-run the .041 unlocker and then the 2.31 unlocker and it ended up working for me. I'm not sure why I had to because I Had the same bootloader info prior to running the 2.31 unlocker in the first place. The 6.5 rom and gps rom has been working flawlessly for a week now, the only thing I had to do was call up VZW (*8889) the guy answered "account investigations" LOL I told him I had to hard reset and my phone wouldn't authenticate and he asked me to call back from another line. I told him that I had no landline and he said thats fine I can override it just call back right away whenever you get to another phone. That was on friday and I have not called back but I've been able to text, make and receive calls so I don't think I will unless I have to.
gooney said:
I think I got it, what I did was not to extract the vogue_unlocker_MFG_2.31.exe file but to run it. I had activesync set up and connected, then just ran the unlocker, don't extract it. It will shut off activesnyc and put my phone in to the 3 color screen, form there, just follow the directions. Also I didn't have to run the exitbl step as my phone auttomatically exit and restarted.
Click to expand...
Click to collapse
thank you! i did that and it worked for me.
yeah, it says right in the directions over there to just run the exe it will create a temp folder and run the RUU itself from there
Extracting it and running it will always cause issues
also - Ignore the sleep4.exe or whatever if you encounter it - it is a legacy exe that is called that isnt used anymore, wont affect the unlocking just hit OK through it
Detroit Doug