Greetings -- I've upgraded to BT 3900 for Motorola HS850 hands-free, which works, although with static.
Now, I got i-tech Clip, and it worked as a hands-free as well. But read on.
I wanted to try it as high-quality audio setup, so I got the profiles -- although for build 3500 -- off the ftp. It did show that profile, but quickly failed to dicover the service on i-tech. As I deleted the hands-free profile, I try to get at least that back. Alas! Now it doesn't connect to hands-free i-tech either.
I've tried: installing 3500, 160.600, -- still discovery fails. What's the rollback procedure to get 3900 with its profiles back?
Braver, I also have Clip S35 from i-Tech. It works so fine with my Xda II (Widcomm Stack + Handsfree Profile and A2DP)
Did you try to reset your Clip S35 and try to pair it together again?
How did you get the A2DP profile? I've installed the profiles for build 3500 from the ftp, it added high-quality audio (is it _the_ A2DP?). I had BT 3900 by then, then reinstalled various versions after i-tech could not be found the second time.
Is it OK to install the extra profiles for build 3500 with 3900?
And, when you do get an audio profile and a hands-free one, how you differentiate -- say, you listen to music and receive a call?
Sorry braver, I misunderstood ...
What I've is :-
1. O2 Xda II
2. O2 Xda II Mini
3. i-Tech BlueCON
4. i-Tech Clip S35
5. IBM X31 (My Laptop)
And I played with them like this:-
(O2 Xda II Mini + IBM X31 + i-Tech BlueCON + i-Tech Clip S35)
I pair my Mini with Clip S35 with the Handsfree Profile. I also connect my BlueCON to my X31 (plug the audio jack of BlueCON to the audio output jack of X31) and pair my Clip S35 with BlueCON.
When I listen the music from my X31. My X31 send the audio output to BlueCON and BlueCON stream the audio data to Clip S35. So I can hear the music.
And when I have the incoming call on my Mini. My Mini connect to my Clip S35 so my Clip S35 stop the music from BlueCON and go to Handsfree Profile Mode. After the hang up the phone line, Clip S35 start the music again automatically.
==================================
For BA, I've seen from the forum but it's Thai language:-
http://www.pdamobiz.com/show_news.asp?NewsID=41062&PN=1
They said that they installed PDA2K_BroadcomCorp_BTUpdate.cab from xda-developers.com like you did and every was so fine.
Please try to check and let me know if there's what I can help.
(Also, don't forget, PIN for Clip S35 is 8888. It's not 0000)
I.tech S35 paired with WM2003 SE with Widcomm 1.6.0600
Guys, help.
I have a WM2003 SE unit with Widcomm 1.6.0600 stack and I just acquired an I-tech S35. I have the following things working:
1. Mp3 over bluetooth using Windows Media Player 9 and the high quality stereo profile.
2. Headset connection for outgoing calls.
I have the following problems:
1. with the mp3, I get interference or what I assume is interference. if I move around too much, the sound becomes choppy.
2. with the headset, I can't receive incoming call. when the call comes in, it doesn't get directed to my S35 even when it's linked via headset mode. I have to answer the phone directly from my XDA2. I tried linking the S35 with a Nokia 6600 and the incoming call is redirected perfectly well into the S35.
3. I can't get the S35 to work in "buzzer" mode, even when I pair it with a Nokia 6600.
4. I've tried calling out and the person I call always says that my call is very unclear.
Does anyone else have problems like this or has been able to resolve these problems? I could use the help or I'd be forced to sell this unit since it's practically useless to me with particularly with the second problem.
Thanks and best regards...
Winston
Hi wsabido168,
1. with the mp3, I get interference or what I assume is interference. if I move around too much, the sound becomes choppy.
Ave*: I don't think that I have the interference problem but the sound is not come out smoothly. I hear the noise like you cooking the pop corn around every 15 seconds per time. You should try to contact to the shop that you bought it and ask them to try with another one.
2. with the headset, I can't receive incoming call. when the call comes in, it doesn't get directed to my S35 even when it's linked via headset mode. I have to answer the phone directly from my XDA2. I tried linking the S35 with a Nokia 6600 and the incoming call is redirected perfectly well into the S35.
Ave*: Mine is not. I can receive the incoming call from S35. I feel like there's something wrong with your XDA II.
3. I can't get the S35 to work in "buzzer" mode, even when I pair it with a Nokia 6600.
Ave*: You can turn it on and off. Please check from the manual. It said that you need to press the button (I can't remember which one) to on and off the buzzer mode. (This problem may relate with your 2nd question, I just guest)
4. I've tried calling out and the person I call always says that my call is very unclear.
Ave*: This question may relate with the 1st question. Mine is clearly (I asked from the other side)
Hi Ave, first of all, thanks for the information.
May I ask what software you have on your system? for example, what bluetooth stack you're using and what version of the OS? Maybe I can reflash my OS to whatever you're using to get it to work properly.
Thanks and best regards...
wsabido168, you're welcome ... I've 2 of XDA.
The first on is my XDA II:-
ROM: 2.06.00 WWE
RADIO: 1.18.00
ExtROM: - (Big Storage)
Bluetooth Stack: Widcomm Bluetooth Stack 1.5.0.2000
The secound one is my XDA II Mini:-
ROM: 1.12.00 WWE
RADIO: 1.13.00
ExtROM: 1.12.119 WWE
Bluetooth Stack: Microsoft Bluetooth Stack
questions:
1. with the XDAII running Bluetooth Stack 1.5.0.2000, where'd you get the Bluetooth Stack 1.5.0.2000? how do I download and from where it?
2. when you're using Bluetooth Stack 1.5.0.2000, can your XDAII receive calls and automatically redirect it to your i-tech S35 even when you're playing mp3s?
3. with Bluetooth Stack 1.5.0.2000, do you have the profile for "high quality audio" with which to use the mp3s over bluetooth?
Thanks and best regards...
Winston
Answer 1
Read from here:
http://forum.xda-developers.com/viewtopic.php?t=17186&highlight=bluetooth+headset+high+quality
Widcomm 1.5.0.2000 File:
http://forum.xda-developers.com/download.php?id=2379
Registry File:
http://forum.xda-developers.com/download.php?id=2378
See here for the picture:
http://www.pdamobiz.com/forum/forum_posts.asp?TID=39555&PN=1&TPN=1
Answer 2
I think the answer is No,
XDA II has the Microsoft Bluetooth Stack installed from the manufacturing. It has Headset Profile but no A2DP (High Quality Audio) available. But if you want to have A2DP on XDA II, you need to install the Widcomm Bluetooth Stack.
The stack from Widcomm has A2DP and can be run on XDA II (but not work on XDA II Mini)
After you install the stack from Widcomm, you'll be able to listen MP3 using Clip S35, but if you want to use your Clip S35 to answer a call, you have to stop the Widcomm Stack and start the Microsoft Stack instead.
Microsoft Stack and Widcomm Stack can be run on XDA II but not the same time.
Answer 3
Yes, Widcomm 1.5.0.2000 has A2DP See Answer 1 for more detail.
Will it work on WM5?
I haven't try it yet but I don't think that it will work on WM5. I'm not so sure, still need someone in this forum to answer for us.
Do you know?, i-Tech has a A2DP software for Symbian OS. It's BluePlayer which I used to try on Nokia 6600. It's really cool because you will be able to listen to the music with high quality audio, also you can answer the phone call with this Clip S35 too.
I used to contact to them to asked for the A2DP software for my Magician. But the answer was they didn't have a plan to do it yet.
Has anyone managed to get Widcomm A2DP working with the headset profile?
wamatt said:
Has anyone managed to get Widcomm A2DP working with the headset profile?
Click to expand...
Click to collapse
On WM2003SE or WM5? With the former, I've used the A2DP profile with Zonet ZUB8100 stereo BT headphones to listen to MP3s. Works pretty well; no static until I get 5-10 meters from the SX66.
Haven't installed WM5 yet, and I don't intend to in the near future.
Hey guys,
Thanks to all the information from you guys, I have gotten it to work (A2DP and bluetooth with my S-35 headset and XDAII (installed with WM2003SE) but still have a problem with the fact that the Broadcom does NOT permit received calls to be redirected to the headset therefore giving it less functionality than if I were using a Nokia cellphone with this headset.
If anyone has a fix to this problem, please let me know.
Thanks and best regards...
Winston
Winston, I took a long time to search on the internet but nobody could give me the information to fix it.
Somebody said that the problem of Headset Profile from Widcomm Bluetooth Stack and Xda II is about the Audio Gateway and Wave Driver. The Wavedev.dll didn't redirect the audio output to Handfree Profile of Widcomm Bluetooth Stack. This is all that I know about.
Anyway, nice to talk to you. Feel free to let me know if there's somethings that I can help or what we can share.
Ave*
ok. thanks again Ave.
3waygeek said:
wamatt said:
Has anyone managed to get Widcomm A2DP working with the headset profile?
Click to expand...
Click to collapse
On WM2003SE or WM5? With the former, I've used the A2DP profile with Zonet ZUB8100 stereo BT headphones to listen to MP3s. Works pretty well; no static until I get 5-10 meters from the SX66.
Haven't installed WM5 yet, and I don't intend to in the near future.
Click to expand...
Click to collapse
I'm on WM2003 Rom 1.40 with WMP10. I can get A2DP working as well, however headset doesnt work properly then (IE can't take calls on the headphones).
Also another annoying problem is that WMP10 turns off after 5 minutes (ie screen goes blank), this interrupts the A2DP session, and I have to reconnect.
is there somebody here tried software like BTaudio, BTToggle, bluemusic, or something else (if any)??
i tried all those software to my BA with win 2003se but all weren't working, and after i upgrade to wm5 (helmi with new bluetootoh stack) still not working. but actually those software working with other pda with wm5 (like xv6700 and i730)
note: there's no problem with stereo headset like i-tech r-35 and jabra BT620s
but i my mono bluetooth (jabra bt110) working also, because its small and using standart battery a3
thanks for any help
Qprett
I've tried with Bluecast, it works on my Qtek 2020i which uses WM2003 SE
http://www.simplesmartphone.com/BlueCast/
I recently purchased an AT&T Tilt (TYTN II phone) with Windows 6.1 Dutty Series... since my motorola KRZR took a dump on me....Quite an upgrade...I am trying to use the Motorola H700 Headset from my KRZR on to my HTC, I can get the headset located in the device menu but I cant get the HTC to pair up with the headset on a continual basis. I am also having an issue connecting to a Bluetooth GPS Antenna. I can locate it it just the same as the headset but it wont pair to the HTC nor ask an authorization code.
Is this a bluetooth glitch? Can I somehow reload the driver for the bluetooth? Perhaps I am doing something wrong but I never had a problem linking bluetooth devices before.....
On a separate note....I tried doing an activesync via bluetooth on my Dell Laptop and it again can be located on both ends but I can get any services to work on either side...
Help?
I have just received a new HTC TyTN II on Orange that has the same problem. My old one (windows mobile 6.0) had no problem with my Motorola H12, but the new one (Windows Mobile 6.1) can't keep the pairing, and I have to turn Bluetooth on an off to get the connection. Always have to enter the passcode.
Version data is:
CE OS 5.2.19212 (Build 19212.1.0.3)
Processor: MSM7200-400MHz
ROM version 1.65.16.25
G 25.83.40.02H
D 3.28.00.00
Any help /advice much appreciated!
O.
Pyper,
i don't know how it is on the H700, but on the BlueAnt Z9, you have to hold down the power switch until the LED on the headset blinks red very rapidly, when it does this, the headset is in pairing mode. then you can pair the phone with the headset. try something like this with the H700. if you can, find out how to get the H700 into pairing mode before you try to pair it up.
hope that helps!
Pyper70 said:
I recently purchased an AT&T Tilt (TYTN II phone) with Windows 6.1 Dutty Series... since my motorola KRZR took a dump on me....Quite an upgrade...I am trying to use the Motorola H700 Headset from my KRZR on to my HTC, I can get the headset located in the device menu but I cant get the HTC to pair up with the headset on a continual basis. I am also having an issue connecting to a Bluetooth GPS Antenna. I can locate it it just the same as the headset but it wont pair to the HTC nor ask an authorization code.
Is this a bluetooth glitch? Can I somehow reload the driver for the bluetooth? Perhaps I am doing something wrong but I never had a problem linking bluetooth devices before.....
On a separate note....I tried doing an activesync via bluetooth on my Dell Laptop and it again can be located on both ends but I can get any services to work on either side...
Help?
Click to expand...
Click to collapse
I've been having issues with my HTC TyTNII with the official 6.1 ROM and the Jabra BT500V headset. The pairing is automatic in WM6.1. The bluetooth causes the phone to be sluggish and causes call drops if the call's picked up within 3 rings or the call's picked up before it rings on the phone (Yes, Jabra rings first before the phone does). I've escalated this issue to HTC SEA Support and they've advised me to disable Bluetooth and test which I did for the past 3 months :|
I have 3 Jabra headsets (BT250, BT500, BT500V) and all are having the same issue with this ROM. I'm quite skeptical to buy another brand just for testing purposes. Do anyone else face the same issue? HTC SEA has fixes available specific for Jabra / Samsung headsets on Touch Cruise but strangely not on TyTN II
Finds BlueAnt S3 but won't pair
My BlueAnt ST3 pairs fast with a Motorola Razr V3xx but the HTC with WM6 Professional, finds the ST3, prompts for the password (0000) but always fails. On the Razr, I touched the enter key but on the HTC it only beeps. I tried the O.K. key too. The message I am getting after touching "Next" says invalid password or connection. Yes, Bluetooth is turned on and the ST3 as well.
Any ideas anyone?
Hello:
Some time ago I bought an unbranded HTC KAISER with WM6.1:
rom version: 3.29.422.1 WWE
rom date: 05/20/08
radio version: 1.65.20.29
protocal version: 25.88.40.04H
BT VERSION: 2.0/2.0+EDR
BT ADDRESS: 00:17:E8:2E:9F:A1
Anyway, I'm still having bluetooth issues with the unit. The BT works great with BlueAnt Z5i on streaming and music listening but I can't get it to work on phone calls, incoming or outgoing. No sound in the headset nor out of the Mic. Same problem with new Jawbone on calls and a Motorola HS860. Before I waste any more money I thought I'd ask about possile regedits etc. to correct this problem? Or perhaps I should consider new Roms?
Ben lurking here and reading and re-reading and getting more confused..anyone have suggestions or can point me to a probable solution?
Thanks for Listening
I finally got it to pair with BlueAnt ST3 and Motorola T305
BlueAnt ST3: I had to delete the ST3 connection, and get the ST3 in "pairing mode" then have the phone search for bluetooth devices. Doing this I got the password screen and entered the 0000. Driving around testing this, it was not as good as the Motorola Razr V3xx. Not always answering, dropped calls ect.
Motorola BT Speaker: I just received a Motorola T305 BT speaker, same process to get it paired. No voice activated call function yet. Just the two beeps, one indicating it is ready for a command and then it beeps again, and clicks out. The ST3 would talk to you and ask for confirmation.
What I have learned so far, the trick is to get the speaker phone in the pairing mode, so the Kaiser phone will prompt for password.
I am going to sell the Kaiser and buy the HTC touch HD and hope for better bluetooth functionality and reliability.
Hmmm... Actually I have no problem pairing any of the BT items I mentioned, just the handsfree doesn't work in all. Thanks for the reply...
Need a help to make T7373RUS works with bluetooth mono handsfree.
Actually it works with, but does not the whole functionality, one thing is missing - it's a voice dialing via pressing call button on BT handsfree. OK, I know T7373 (non USA) does not have any voice dialing, but this is a WM, well I set up VITO VoiceDialer and it works perfect. But there is a problem - my bluetooth handsfree don't launch it. I've tryed to use wired handsfree it works perfect. What is a point, why such perfect phone cannot does that any nokia or SE phone does like a piece of cake.
Please help, this is really sad thing need to be fixed, can some one to figure out how to solve this?
May be anyone know USA version of Tp2 uses the same bluetooth stack?
May be some parts of USA version software is possible to integrate into my TP2?
Does anybody use Bluetooth handsfree with HTC TouchPro2????
I don't know if this is the correct board, but here it goes..
I just bought Nokia BH-111 (http://nokia.ly/ACiqj6) bluetooth stereo headset and I can't pair it with my Omnia 7. Works fine with Nokia 5230 phone, so it's not a problem with the headset. The phone does not even detect the headset, it keeps showing "searching" and nothing happens.
This is what nokia product page says about compatibility:
"All phones, music players and other devices that support Bluetooth v. 2.1 + EDR, Handsfree Profile 1.5 and Headset Profile 1.0"
This microsoft support article ( http://support.microsoft.com/kb/2449475 ) has this to say abozt supported profiles:
Advanced Audio Distribution Profile (A2DP 1.2)
Audio/Video Remote Control Profile (AVRCP 1.3)
Hands Free Profile (HFP 1.5)
Headset Profile (HSP 1.1)
Phone Book Access Profile (PBAP 1.1)
+ v2.1 with EDR
So as you can see, WP supports EVERY one of those profiles and standards. What's the problem than?
Does your Omnia find other devices?
Omnias are notoriously bad for having faulty Bluetooth. My first one stopped working properly. Replacement is fine.
In the Omnia 7 section there are quite a few people who've reported it.
Thanks for the reply.
It seems that the issue is with WIFI and Bluetooth working together. After i turned wifi off, Omnia was able to find the headset. The playback is a little patchy, and rewind/fast forward does not work. Is this a reason enough to ask for a replacement? Does the warranty cover it?
EDIT: sorry i posted here, i thought it was WP software related, plus Omnia boards are almost empty.