Related
It might be very simple to all you educated guys, but I am sure there are a few more like me that are a bit baffled by some of the threads on here.
What would be REALLY nice would be a 'simple' step-by-step guide to installing wm6 on our devices, and what we need to download to achieve it, eg "you need this for MDACIII, and this for O2 Orbit"
Obviously anyone trying it runs the risk of buggering up their phone, but that's their own fault.
Any volunteers?
stunno said:
It might be very simple to all you educated guys, but I am sure there are a few more like me that are a bit baffled by some of the threads on here.
What would be REALLY nice would be a 'simple' step-by-step guide to installing wm6 on our devices, and what we need to download to achieve it, eg "you need this for MDACIII, and this for O2 Orbit"
Obviously anyone trying it runs the risk of buggering up their phone, but that's their own fault.
Any volunteers?
Click to expand...
Click to collapse
having asked the same question myself here goes.
Download USPL and follow the instructions. they are very clear.
Download
extract
connect phone with minimum 50% battery
soft reset and once started up fully run the app by clicking on Rom Update utility
follow the process through once finished your device will restart.
once restarted you then can flash the rom of your choice
I used Black and Blue again ran the update utility and bingo.
dont forget that all data on your device will be lost so make sure you have back up of contacts etc in outlook on pc.
Finaly make sure you have Activesync 4.5
enjoy
AS STATED ALTHOUGH THIS WORKS YOU ALL DO IT AT YOUR OWN RISK
Id just like to know really is that how many people have done it without unlocking the device for o2 orbit uk. i have one and am not really willing to try it unless i know there are people out there that have tried it and it worked.
as there is no rom install file from o2 for this, there is no way bacj and bricked phone is the only way forward. id like not to brick my phone as i need it daily.
so, has anyone with a locked o2 device upgraded to WM6 successfully and which rom did you use if it worked.?
joey jojo said:
Id just like to know really is that how many people have done it without unlocking the device for o2 orbit uk. i have one and am not really willing to try it unless i know there are people out there that have tried it and it worked.
as there is no rom install file from o2 for this, there is no way bacj and bricked phone is the only way forward. id like not to brick my phone as i need it daily.
so, has anyone with a locked o2 device upgraded to WM6 successfully and which rom did you use if it worked.?
Click to expand...
Click to collapse
i have o2 uk orbit and all is well
pof said:
I created update package for this ROM in NBH format, so no risk of bricking when flashing it, just unzip & run RomUpgradeUtility.exe
Download here:
ARTE_WWE_WM6.zip
NOTE: Before flashing you need to have Artemis USPL on your device.
Click to expand...
Click to collapse
Taken from Bepe's thread about the modified o2 German update. Basically you need to use the Artemis USPL program and then use the first link to install which I did successfully on a CID locked phone.
Thanks guys, but, unfortunately, the uspl thing does not work on my pc
Along with a few others I get the 'black screen' on my mdac3 then activesync disconnects and the rom loader throws up an error
Luckily my mdac3 survives through a soft reset
I think the idiots guide is not quite there yet
hi..
i have O2 uk orbit.. which is still locked, i fully charged the battery, completed a hard reset of the phone used the pof Artemis Update SPL (USPL) v.01 upgrade (wow what a brain box he is!) just in case it failed, so i could you use any NBH file to get you orbit to work again if i failed. Then used Bepe's WM6 os.nb file renamed it to windows.nb downloaded ATRE.zip unzipped the ARTE.zip file placed the windows.nb into the same directory, don't forget to edit UpgradeRom.bat file 0x3900000 to 0x3500000 with in the ATRE directory and copied and installed EnableRapi.cab to the phone. Reset it the phone and then started the UpgradeRom.bat! 12 mins later upgrade complete. Hard restart the phone.. Chewing nails by now... all went well did a soft reset of the phone before the O2 ExtROM autorun starts..
sorted, and did half way though a night shift at 3 am.. not bad at all!
crushuk said:
hi..
i have O2 uk orbit.. which is still locked, i fully charged the battery, completed a hard reset of the phone used the pof Artemis Update SPL (USPL) v.01 upgrade (wow what a brain box he is!) just in case it failed, so i could you use any NBH file to get you orbit to work again if i failed. Then used Bepe's WM6 os.nb file renamed it to windows.nb downloaded ATRE.zip unzipped the ARTE.zip file placed the windows.nb into the same directory, don't forget to edit UpgradeRom.bat file 0x3900000 to 0x3500000 with in the ATRE directory and copied and installed EnableRapi.cab to the phone. Reset it the phone and then started the UpgradeRom.bat! 12 mins later upgrade complete. Hard restart the phone.. Chewing nails by now... all went well did a soft reset of the phone before the O2 ExtROM autorun starts..
sorted, and did half way though a night shift at 3 am.. not bad at all!
Click to expand...
Click to collapse
Confused... is it really necessary to take all these steps? I thought that the only thing required is to run Pof's tool USPL, and after that run Romupdateutility.exe from the package in .nbh format (the link is just a few messages above yours). Please correct me when I'm wrong.
step by step guide
stunno said:
Any volunteers?
Click to expand...
Click to collapse
OK, I volunteered... This is a detailed list of steps how I installed a new ROM on my MDA Compact III (CID locked, at least I think so). It worked without any errors or problems. I used PDAVIET Black&Blue v2.0. It was my first flash on my Artemis, so I more than understand your need for step-by-step guide
1. download the file Artemis_USPL.zip
2. unpack into the folder c:\USPL
3. download the file ARTEMIS_Black_Blue_v2.zip
4. unpack into the folder c:\ROM
5. soft reset your phone and have it charged over 50% (I have it fully charged)
6. wait until the system starts on your Artemis
7. turn on flight mode (probably not necessary, but I wanted to minimize any risks)
8. connect your Artemis to PC with a USB cable
9. wait until ActiveSync icon in your tray (lower right corner of your windows desktop) turns from gray to green. If you connect your Artemis for the first time to PC, you do not need to set up synchronization, just click "cancel" on the first screen of "Synchronization Setup Wizard"
10. while ActiveSync icon is green, run c:\USPL\start_uspl.exe
11. a DOS screen will pop up with the text "Initializing: 0.." in the bottom indicating probably seconds from the start (it stopped around 70 in my case after about 1.5 min)
12. DOS screen disappears and PDA Phone ROM update utility pops up
13. at the same time, your Artemis turns blank (orange/green LED turns off as well)
14. tick the check box next to " I understand..." and then click Next
15. tick the check box next to " I completed..." and then click Next
16. a box saying "Verifying information on your PDA..." pops up
17. on the next screen click Update button
18. next screen says "Upgrade to ... image version 9.99" - click Next
19. Next screen says "You are now ready to update..." - click Next, a window with a blue progress bar appears with a text "Updating ROM image..", it quickly runs to 100%
20. next screen says "Congratulations! ..." - click Finish
21. your phone turns on and boots into your old system, however it should be CID unlocked now
22. your Active Sync should reestablish and icon turns green again
23. do not touch anything (phone or USB cable) and run C:\ROM\ROMUpdateUtility.exe (make sure activesync icon is green)
24. PDA Phone ROM Update utility window appears, tick the check box next to " I understand..." and then click Next
25. tick the check box next to " I completed..." and then click Next
26. a box saying "Verifying information on your PDA..." pops up
27. on next screen click Update button (says "Current information...")
28. next screen says "Upgrade to ... image version BnB2.0" - click Next
29. Next screen says "You are now ready to update..." - click Next
30. a window with a blue progress bar appears with a text "Updating ROM image..", your Artemis will have light gray screen with blue progress bar showing the progress of flashing - do not touch anything and wait (it took 2-3 minutes on my 3 years old PC)
31. next screen says "Congratulations! ..." - click Finish
32. your Artemis turns on and starts booting, you can disconnect it from PC now
33. the boot screen remains the same (T-Mobile in my case), so do not panic!! it is normal
34. wait until calibrate the screen appears, calibrate, choose time zone and you are ready to use your new OS
35. let me know if this manual was clear enough, whether it helped you and please suggest potential changes for improvement
Take care,
Dzim
i've just succesfully flashed my dutch CID-LOCKED MDA Compact 3 with this method, so i'd say it's reasonably fool-proof
A couple of questions before i take the plunge - if my t-mobile cmda iii is already CID unlocked, can i just go straight to the update rom part.
Also, is there any way of dumping my standard t-mobile rom first off? I'm having trouble trying to use itsutils due to the app lock.
Cheers Dzim!
Your instructions worked perfectly.
One very happy complete idiot here!
Furbious said:
A couple of questions before i take the plunge - if my t-mobile cmda iii is already CID unlocked, can i just go straight to the update rom part.
Also, is there any way of dumping my standard t-mobile rom first off? I'm having trouble trying to use itsutils due to the app lock.
Click to expand...
Click to collapse
There is a TMobile rom on here somewhere already, I just cant find it at the moment
My Compact 3 it’s death now. After pres voice commander button MDA start only to the boot loader. Can’t run complete system.
Pleas tell me. How can I write the new rom with WM5 or WM6 ?
OOPS! Working well apart from the "cant save word documents" bug!!
Just an update - to use the v1 or v2 black and blue, even though it is unlocked, you still need to use the supercid util.
Otherwise you get the rom update getting to 3% before crashing out to say the rom is corrupted.
I've now converted 2 other tmobile compact mda IIIs successfully, wm6 is much quicker
Yes, with my Compact was exactly as You say. Now is death. What I can do now to repair it.
big thanks to Dzim, used the idiots guide and now on wm6 =D
cheers!
PS: first post
Hi! Nemesis, try to connect your HTC to your pc in bootloader mode.
Lauch start_uspl.exe in USPL folder. Follow instruction on post N°9 by DZIM.
After USPL your HTC should reboot (maybe in bootloader mode only).
Launch the ROMUpdateUtility.exe in Black&Blue ROM v2 and follow instruction.
Thanks gguyaz
Pleas tell me.
Could I doing this upgrade with Windows Vista on my PC?
Hello Everyone. I Am Trying To Istall The Official Wm06 But The Bootloader Does Not Respond. Any Sagestions Pls
U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.
Twiggerdingo said:
U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.
Click to expand...
Click to collapse
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .
robinbatman said:
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .
Click to expand...
Click to collapse
Ok, let me see if i understand u correctly, your specs give me no new questions they look ok. U have WM5 and want to run a program (from your work) which needs WM6 (wont run on WM5). HTC told you about the official WM6 update. This wont flash as activesync crashes, right?
With an official Rom you will not need to unlock the CID/SPL with USPL. But this goes only when you stick to your current language. i.e. a german WM5 is not allowed to be flashed into english. To do this you will need to USPL-unlock it 1st.
If the language is the same, it should work. Best is to do a hard reset 1st (2 soft buttons and soft reset, wait and press green/send.) Afterwards hook it on the PC (activesync want to start a newe partnership, click cancel, so u will be connected as guest).
Start the rom upgrade. Activesync should close and bootloader on the ppc will be started. This is a screen with many colours/stripes, which is normal but looks very bad and different from normal bootup.
Then the flashing will start, the screen on the ppc will turn white/grey and a scale will show you the percentage of the flashingprocess (similar to the screen of the pc). Wait patentiently and do not toch the ppc or disconnect (or expect a bricked device).
At the end, the ppc will reboot and take a while (longer then normal bootup) to initiate the boot for the 1st time.
If this wont work, then try to extract the upload file, put the ppc in boatloader mode, connect to pc and start the romupdateutility.exe directly.
Good Luck!
hi,
i've flashed my HTC P3300 and it was done successfully (using USPL) but the language was Spanish, i searched a lot how to change it to english since i dont understand a word of it.
through one of the forums, i was told to set the SysLang = 1032 in registry to get the english language, i done so, now, the phone is stuck in Welcome (WM6.1) screen and nothing is happening, not even responding to power key.
I tried hard reset, it doesn't work, i tried entering to bootloader, it also doesn't work, also, i am not able to connect it to PC since i guess its not completed up.
Just got stuck with a brick, can you help please. Really needed!!!!!!
Thanks
Maybe flashing ROM from memory card may help. Search Artemis wiki for micro card ROM flashing.
Hello, I guess I'm having the same problem...tried to flash but something went wong and now I have my htc p3300 blocked with the multicolor screen. It does not work, so I don't understand how I could start flashing rom by memory card. Could you be a little bit more detailed? Thanks in advance
Hi guys.
I was using the installed the FInixNOver 3.0.1 ROM onto my SPV M700 and it was great. I've had it for about 2 weeks without any problems.
Last night I looked at my phone, only to realise that it was completley dead. This didnt shock me to much because the battery was running low, and i decided to let it die completley before recharging it again.
I charged my phone overnight and switched it on this morning, but the phone would freeze at the 'FInixNOver' splash screen (the numbers at the bottom of the screen would appear overlaying the splash, but the phone wouldnt go pass this point).
The only way to turn off the phone from this state is to eject the battery. I have tried removing the sim card, turning it back on in as many ways as possible but to no avail. I am able to get to the TriColor test screen (im running IPL-0.50 / SPL-1.30.Olipro) but with all the custom roms available, they all use the ROMUpdateUtility which requires the phone to have established an activesync connection initially (but this would mean my phone would have to be 'on completley' - so this is catch 22.)
For the record, my phone/battery died while my wired handsfree was attached (dunno if thats of any interest to anyone or the rom baker).
But it looks like the only way i'll be able to flash my phone is by finding a way to install the .nbh file without using the RUU method. Because I can put my phone into test mode manually.... any help or guidence would be very much appriciated.
Thanks.
Ok can you get it into bootloader? power/camera buttons and reset?
sorry didnt read fully.
right get your device into bootloader first,
then open active sync (are you using xp)
then open connection settings and disable usb connection,
put your device into bootloader mode, then run any rom upgrade, i prefer the WM6.1 pdaviets from HERE (Username: PDAVIET / Password: pdaviet)
Your pda does not need active sync with ruu's, so no catch 22. if you turn off usb connection in active sync, you can still run ruu and it will be recognised, unless you are using vista, where you need to change your HTC SYNC drivers.
Thanks for your quick response...
Yes I can get into boot loader using the power and camera buttons (or holding the power and camera buttons when resetting the phone)...
When the phone is in boot loader mode, active sync doesnt even detect the phone anyway, but nevertheless, I have followed your instructions and disabled the USB Connection. (BTW, yes i am using XP)
The phone is still in boot loader mode, so now i try and execute the ROMUpdateUtility.exe and go through the steps, at the 1st step i tick the tickbox and click next, and the 2nd step i tick the tickbox and click next. (this step says DO NOT enter the bootloader manually? - but i have havent i?) anyway, when i click next, it says... "Verifying the information on your Trinity... Please Wait..." for about 10 seconds, and then i get a message "ERROR [260] : CONNECTION"
What am i doing wrong?
Huumm.. why dont you flash your phone throw the sd card??
Read this link:
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
try to flash your phone with some official rom and after that flash it with any other you want!
manos_23 said:
try to flash your phone with some official rom and after that flash it with any other you want!
Click to expand...
Click to collapse
I would recommend this option above, to be safe, i usually get them error messages when the battery is below 50% or sometimes i try it again and it works. it does state do not manually enter bootloader but i always do it this way.
also make sure active sync is not still running in taskmanager under the alais: wcescomm.exe and WCESMGR.exe, end them both.
I've just tried using an official ROM, but the problem still occurs with the 'connecting'. It doesnt seem that the computer picks up a connection to the phone whatsoever.
Should i be concerned that at the bottom of the bootloader screen it says "serial", is this correct?
Im starting to get annoyed now.
Bye,
the bottom of the sreen mast say "usb" not serial.
it seems there is a problem, if it states serial. as it should say usb. try THIS
Seems like the problem was that my USB lead was loose and made a bad connection, hence why the bootloader showed 'serial' and not 'usb'... as soon as i wiggled it and heard the 'connection noise' in windows, i knew i was good to go, and so using the RUU worked fine to reupdate my phones ROM.
Thanks for your help.
My only question is that why did it happen in the first plave?
WIZZKID - I just saw your post here now. I have to tell you that I also saw "SERIAL" at the bottom of the bootloader screen and not "USB". As I said I returned it to get another phone but maybe I will try something else for now instead of a P3600i. I will monitor your thread to see how it turns out for your phone, because it seems that we have the same problem.
if you see "serial" instead "usb" your problem is in the usb cable, usb port from your computer or in the usb connector from your trinity!!!!!
I was having the same problem that you have!! my problem was from my usb from mine trinity!! see if the conector is at good conditions !!!
Well as some of you may know, I got my Trinity replaced for sticking at the WM splash screen after a few days. This second one - I have had it ONE night - and the same thing has happened with incomplete booting. This time I have been trying all night to flash the phone to an official ROM, but I cannot do it (apparently) because I can't establish a connection via ActiveSync. When I stick the data cable in while in bootloader I see SERIAL replaced by USB and when I try the flash I get a "270" error (cannot connect to phone) and the phone re-boots to the sticking plash screen. What should I do now?
ladies and gentlemen...
we've got a lot of mixed messages in this thread.. please make sure you're posting the right thing. no need to disable USB when manually going in to bootloader to flash (at least in xp).. Also, you can ignore the part of the RUU that says 'do not manually enter bootloader' (you should really read the guide on my site)
foxuniform- can you please give some details..
1) are you running xp or vista
2) have you flashed hard-spl? if so what version?
in the mean time, try a couple of things.. first, flash hard-spl (even if you already have it, but from the sound of it i think you don't have it on your device).. if that works, try to flash an official ROM. Can also try to use splxploit, then flash hard-spl, and then flash official ROM (there's a guide on my site if you're unsure)
please post your results
*edit*
here are the steps for SD card upgrade, but i HIGHLY recommend flashing Hard-spl first..
try to do it from SD card. how?
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract (http://www.cabextract.org.uk/) .
Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
When flashing completes soft-reset your device.
Make sure your SD has FAT32 and has no label. There have been reports that if SD has a label the bootloader can not access the TRINIMG.nbh
racerx_ I have carefully read your response and suggestions, and thanks for your expertise input on the matter. I am fairly new to this stuff so read below carefully as you may find errors in the way I tried to go about doing what I was hoping to accomplish.
First let me answer your questions. I am running Windows XP. The phone is in it's completely natural state in that I have not flashed it in any way. The ROM I was TRYING to flash to the phone while it was not starting properly (this is where I manually entered bootloader) is an official ROM from the HTC website (please note everyone that when I registered my P3600i on the HTC website it came up as the Dopod 810). Anyway, that never worked. ActiveSync never detected the phone (and I guess that's the reason I could not do anything as far as flashing goes). I HARD-RESET my P3600i and it booted normally. I re-installed all the stuff I had on it, from memory card to various .cab files, and the phone is working beautifully thus far. I will report if anything funny happens again.
I have to ask you racerx_, if I CAN flash hard-SPL on the P3600i according to the lovely guide on www.trinityguides.info. I have been of the opinion that things don't work for the P3600i as they did for the P3600, and that has been echoed by many P3600i users on this forum who are ready and waiting to try out some cooked ROMs (myself included).
For the sake of record, my phone is running rom version 3.00.707.17 and radio version 1.46.00.11. I patiently await your response.
woaaahhh..
i didn't notice the 'i' in your previous post... yeah, as far as i know, these ROMs are not flashable on your p3600i.. sorry..
**correct me if i'm wrong somebody**
Yeah I kinda thought that would be your response. By the way - do you think that this phenomenon of sticking at the Windows Mobile splash screen (both the P3600 and P3600i models apparently) has anything to do with something users do with the devices, or you figure it's an inherent software glitch of some sort? I am wondering if I should try a different model or hold on to my P3600i? Hope it's not something that'll happen again - I fly for a living and it's not gonna be good to have the thing screw up on me away from base - I really count on it for everything from casual keeping in touch on Messenger to viewing my work schedule. I love the Trinity though - it's one of my all-time favourite HTC phones.
hmm... i don't think its inherent in the Trinity.. (not a hardware issue.. in my opinion)
its been a while since i followed the posts on it, but always seems to be software related.. sometimes ROM-specific problem. Personally, i've probably flashed as many ROMs as anyone and the only time i ever encountered problems was with the official HTC WM6 ha.. go figure.. I think ppl did find that hard resets before and after flashing are helpful as well..
i love my trinity, and there's not much else on the market to make me want to trade it in (is it just me, or have pda's kind of stopped getting cooler).. i'd stick with it..
I'm running Vista and when I wanted to run the bootloader upgrade on my Dash I kept getting this message error. Error 260. anybody find any way around it? I've tried to manually set th ephone into bootloader mode, same result. help!! PS the error is supposed to mean "port already open" or "open port error" I'd really appreciate any help!
erro 260 - fixed
switches to my wife's laptop that had XP on and it worked like a charm. I'd be glad to assist anybody in the process od de-branding their Dash. Removing the ugly T-mobile paint logo on the unit was easy too.
ERROR 260
Sorry for thislong story....
OK, I've been on looking around the site for a while. I installed the WM6 Beta. I was looking for two days for the WM5 ROM only because I want the little things to work. Finally found it. But now every time I try to flash my phone ack to WM5 bI keep getting the 260 connection error. The readme only says to restart the comp and phone and try again. I have literally, no joke, done this 12 times in the last 2 hours, hoping maybe it will go. All the phone does is go to the green, blue, and red screen and stays there. Then the comp says it gets the error. I know it's connected because Sync Center syncs, I can look through the phone, install apps from my comp, etc. Also I tried doing the 'Update only' rom for version 1.11 or so, and it starts to go but then says its the wrong version RUU. Has anyone had this problem before? Flashing to WM6 did this once and then worked after.
I'm running Vista Premium, stock sync cable, Microsoft Sync Center for vista. All this is the sameas when I flashed to WM6.
There goes another 3 attempts, trying to change timing, reinstalling Sync Center, etc.
Decided to try it on my XP desktop, and for some reason, first time it worked. Maybe Vista didn't like it? Who knows..
Mladito Vista!!
Hi there,
I have the same little problem here!!!! I have a laptop with Vista (garbage)... so i´ll try on a laptop running XP...thank you for posting this, it was a big help..i let you know how it turns out... see you around
WM5 to WM6 --> Problems at 3%
Hi all,
I've errors upgrading my phone to WM6.
I Can open the Wizard (it`s a generic to S620/S621), but in 3% i`ve an error.
I think thats my phone has a blocked CID.
How can i unlock this? i`ve tryed with tools to unlock, but without success...
Regards,
Emerson
Hello,
Welcome to the forum.
Your problem is that your phone is CID-Locked. Hence, you'd need to use a paid service to unlock it. I personally used the following service which provides instant unlocking:
http://www.gsmliberty.net/shop/htc-excalibur-instant-remote-unlock-p-1452.html
I used a credit card, it's 39.99 $ - I was done unlocking and upgrading to Windows Mobile 6 in about 15-20 minutes.
Good Luck !
P.S:
Steps to install WM6
- First CID/SIM Unlock using GSM Liberty
- Flash Bootloader
- Install WM6 ROM (It will take some time for it to load so give it about 5-10 mins. it does get stuck at the boot screen for sometime but eventually it'll load)
- Install Office/Audio Manager
- Application Unlock your phone using SDA Application Unlocker
- Install the necessary software/tweak/hacks
there you go, if you have any questions, feel free to ask. also, if you use the search function, everything's available here.
Good Luck !
Here's the following links you require
1) Flash Bootloader
ftp://xda:[email protected]
2)here's the WM6 ROM:
http://files-upload.com/files/472108....90_Ship.ex e
here's office for those who want it:
http://rapidshare.com/files/31706137/Office.WM6.zip
here's Htc Audio Manager for those who want it:
http://forum.xda-developers.com/atta...1&d=1183909664
Ps. I better like German flash, it's smaller due to fewer language packs, and contains English, here: http://files-upload.com/files/472422....90_Ship.exe
thanks to jsp_m for the links.
Hi,
I`ve problems because my IMEI is from Brazil...
And in the site accept only 15 digits IMEI..
My imei is: 35*************02 (17 Digits IMEI)
Thanks,
Emerson
hey,
that's not a problem. everyone has 17 digits, don't include the last 2 digits when you type in your IMEI so for example
11111111111111102
just include the first 15 and submit and you'll get an unlock link in your e-mail, follow that link, scroll down to the page to download dashunlock software and download the .UNL file for your IMEI and then make sure ur phone is connected to active sync and it's green, open the dash-unlock program and then hit enter then it'll ask for the .UNL file, locate it and open it and your good to go - your phone will be unlocked then soft reset it or i think it's automatic and everything's set.
good luck !
p.s: in other words, don't include 02 when you type in your IMEI.
HTC Audio Manager
http://forum.xda-developers.com/showpost.php?p=1355010&postcount=5
Thanks!
I'll Try NOW and let all know...
Regards,
Emerson
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
tatarezende said:
Arrghhh!!
My phone still give the message:
Invalid Model ID [244]....
And now? i`ve payed 40 bucks for an unlock software....
Thanks,
Regards,
Click to expand...
Click to collapse
Emerson;
Read the second post from luckybandit on this thread. That´s exactly what to do to get rid of the "invalid model" issue. Download the bootloader, flash the phone, flash the new ROM and be patient.
My excalibur is also from South America, and worked OK. If you have any doubt just let it know to this thread.
Boa sorte!
Hi,
I`ve problems with the link of Boot loader....
Anyone can send the full URL?
Thanks,
Regards,
Emerson
Hello,
I'm sorry about the links not working, here - i've attached the bootloader for you. here's what you do
1) Run bootloader (attached file)
2) Run the WM6 WWE ROM
3) Run SDA Application Unlock
4) Install Office/Microsoft Voice Command/HTC Audio Manager
5) Install Tweaks/Hacks
here's a site that has some applications and tweaks:
http://mobile.surrealnetworks.com/DashApps.htm
and search this forum, there's tons of information, hacks - etc.
Good Luck !
oh by the way, did you unlock your phone properly?
1) Download unlock software
2) Download .UNL file specifically for your IMEI
3) Connect phone to computer and make sure the activesync's icon has turned green
4) Run unlock software
5) When unlock software asks for .UNL file, browse for it, choose it
6) That's it ! It should say Unlocking done and it'll reboot
Your phone is now Sim & Cid Unlocked. If you have more questions, feel free to ask. just do what i said first then post.
Good Luck ! Hope to see everything working for u...
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
tatarezende said:
Hi again...
Now i`ve the Error 260 message everytime my phone boots in "Flash mode" (3 color screen)....
Follow my configuration in this screen:
Excalibur Wi-Fi RUU
ONBL 1.15.0000
Excalibur
SPL 1.15.0000
Excalibur IU
ERROR [260] - No connection
Click to expand...
Click to collapse
Hi,
Are you using Windows Xp? Cause I've gotten that error a couple of times too but it was in Vista. Try Xp if you're using Vista.
Hi!!
DONE with XP.... but now i`m affraid!! The "Green Screen" with nem OS apparently locked... this is normal? at least 3/4 minutos in the same screen.. both "patches" are applyed sucefully....
Is there anything else to do now?
Hi there!
I am in serious need of help with my iPAQ hx2490. Yesterday, I tried to do the
official HP ROM Update. Everything went well, up to about a point when the RUU told me that there is a connection problem with my device.
The update went to just about half way through, and I didn't touch anything, I just left the device in it's cradle.
Anyway, my problem now is, that the device won't start the OS, I can't get past the HP welcome screen. The loading bar fires up, and completes it's way to the right, but after that: NOTHING!
I have tried soft, hard and clean reset, without any help. When I do a clean reset, the display shows "Formattin PS", and the loading bar reaches the right. But after that: NOTHING again!
I tried flashing everything again, from WM 2005 first and second edition, even WM 2003. The result is always the same.
I can get it into Pre-Bootloader, normal E-Bootloader. I do get a "USB Connected" message, and I do get the following "USB" message on the screen.
Now here's the odd thing (and I do hope that all you experts are dying to solve this mystery!): when I do the update again, at either 84,1% or sometimes 85,1%, the iPAQ shuts down, and starts again. But this doesn't stop the RUU from continuing!!
I've tried everything I can, I read all the infos in the forums concerning iPAQ problems, but they're mostly concerning entering bootloader, which is NOT my problem.
Money ahead: I'll donate 10€ to the person who is able to solve this riddle!!
The money can go to either this website or the person's own PayPal account.
oh I forgot: I did try ChrisMRulz bootloader method, but I wouldn't work for me. I managed as far as the MTTY program firing up, and I do get a WCEUSB prompt, but can't enter any commands, and the nbf file doesn't get uploaded!
PROBLEM SOLVED!! Sorry.....
Can you tell us how?
Maybe it will be helpful for others that have similar problems in future.
Sure, I can do that:
I managed to flash the official International English ROM Update to my german hx2490 iPAQ. I just used the trick that you have to start the correct HPRUU.exe for your country-specific device, but just before you hit the last "Update" button, you change the .nbf file with the one you want to flash.
But you have to rename it to according filename the HPRUU.exe originally loaded,
if you don't rename it, the update utility will crash.
By doing so, I was able to flash the above mentioned ROM to my device, and after that I just flashed my country-specific ROM.
Now I'm back and running WM5.
If further explanation is needed, I'll gladly help out someone with the same problem.