Related
I upgraded...so I thought to this version...
Rom Version 4.01.16 eng
Rom Date 02/04/01
Radio Version 4.21.00
Protocol version 32s54 now I cant get into bootloader, cant use the phone, or internet on my SX-56...nor can I boot by flashing....What Have I done wrong should I just use it as a paper weight? Remeber If I press the power button and soft reset to just goes back to the Tmobile screen an continue to boot as a normal Alt-Ctrl-delete. I have tried xdairt and himayla..cant get it to work...
someone plz guide me through this I want my pda!!!!
Try the option fix-bootloader from the XDATools.
Then you should be able to enter the bootloader, and reflash your device...
HTH
Stefan
after XDA1 ugrade to 4.01.16 not able to do up/downgrade !
Have upgraded my XDA1 to ROM-version 4.01.16 Eng.
Now I wanted to install a different version, but I failed.
The PDA is working so far, but I can't upgrade/downgrade anymore.
When I use OSImageTool, there is a connection error displayed in the black command window:
ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host. error getting connection type.
Can somebody please help me ?
Re: after XDA1 ugrade to 4.01.16 not able to do up/downgrade
Stefan_PDA said:
Have upgraded my XDA1 to ROM-version 4.01.16 Eng.
Now I wanted to install a different version, but I failed.
The PDA is working so far, but I can't upgrade/downgrade anymore.
When I use OSImageTool, there is a connection error displayed in the black command window:
ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host. error getting connection type.
Can somebody please help me ?
Click to expand...
Click to collapse
There are many postings concerning this problem.....
You have to flash via SD-Card....
HTH
Stefan
Cant get into bootloader via pressing pwr botton and soft reset. I've have also hard reset the device and i still get nothing
Have you tried the fix-bootloader option from the xda-Tools?
Stefan
yes...but all i get is tthe command prompt...and i click yes is there something else i must do...tried edit2003 but still nothing
Cannot execute
Cannot execute "C:\DOCUME~1\Ovynten\LOCALS~1\Temp\Rar$EX00.203\RSUpgrade.exe"
wHAT THE [email protected]#$ DOES THIS MEANS? If uI could only understand this maybe I could get mt PDA working again.
Please help
I can't seem to get my Jasjar flashed. I dont know what I'm doing wrong.
Piesang said:
Please help
I can't seem to get my Jasjar flashed. I dont know what I'm doing wrong.
Click to expand...
Click to collapse
Read this thread first, especially the first post. You can skip step 1 and 2 as long as you have the 11 files on the list. Here: http://forum.xda-developers.com/showthread.php?t=269118
cktlcmd said:
Read this thread first, especially the first post. You can skip step 1 and 2 as long as you have the 11 files on the list. Here: http://forum.xda-developers.com/showthread.php?t=269118
Click to expand...
Click to collapse
Thanks m8
I'll have a look at it. I appreciate the help.
I must be stupid becaue I'm not getting it right. I keep on getting "Connection Error"
Please help.
maybe this will work for you
hello,
i too have problems with flashing roms. i have bootloader 1.01 and it ignores whether the device is connected via usb or not - it will simply display 'Serial' or 'USB' no matter whether i disconnect or connect the device. however i have found out that to be able to flash your device one must in such case:
1) enter the bootloader mode (flash+power+reset) repeatedly until you will see both 'USB' on the device screen and 'USB' as a connection option in mtty. it might help trying with both disconnected and connected device while entering the bootloader mode. this is the worst part.
2) once you see 'USB' as a connection option in mtty, choose it and connect. Press ENTER, 'USB> ' prompt should be displayed, type 'set 14 0' and press ENTER. close mtty
3) enter the device into the bootloader mode again. this step is needed, without it the flashing application will timeout.
4) now you should be able to flash it.
hth, fuf.
Try reading this thread: http://forum.xda-developers.com/showthread.php?t=285299
I think you have the same problem where the computer can't recognize the Universal. The solution is in there too.
cktlcmd said:
Try reading this thread: http://forum.xda-developers.com/showthread.php?t=285299
I think you have the same problem where the computer can't recognize the Universal. The solution is in there too.
Click to expand...
Click to collapse
Thanks m8
At last I got it right. I'm first trying the Helmi 3.3 Rom. Will try the Latest Jasjar Rom later.
I get a error when my Jasjar boots.
sddaemon.exe cannot be opened.
What is this?
Broken Radio ROM blocks official O2 rom, MaUpgradeUt_noID.exe fails "error 114"....
Hello
I hope someone here is able to help me.
I have spent the whole of the last 48 hours (no sleep) trying to fix my O2 XDA Exec. I *believe* that I have tried everything suggested on this forum and on Buzz's site but there is just so much on here now that I may well have missed something.
History:
Over the last few months, my phone has gradually got more inconsistent - dropping calls, refusing to answer calls, losing signal and so on. On Jan 1st, I turned it on and it had lost all my settings - Opera reg code, Wifi encryption, O2 net settings, etc.
I spent the last week with sometimes having network, sometimes not. Finally it just gave up altogether. In Settings>System>Device Info, "Radio Version", "Protocol version" and "IMEI" are all completely blank. When booting, the red text states "No GSM".
Reading around this site it appeared that I should be able to reinstall the radio ROM from the official O2 download however this errored with the Incorrect Country Code error. I have carried out full hard resets and still cannot get any Radio ROM visible. I assume that the lack of IMEI is affecting the official O2 downloads?
Since then, I have tried most variations on this site of ROM installs using MaUpgradeUt_noID.exe suggested in the wiki (with and without entering mtty code: "set 14 0").
Full three-part ROM and radio-only ROM install attempts all fail with the Error 114 "Radio Rom Update Error" (the radio ROM is always attempted first).
The only success I have seen was an update of Bootloader from 1.00 to 1.01 which worked completely perfectly and proved that the PC can indeed connect to the XDA when it feels like it.
After two days of earning no money ( I am self-employed) and no money to spend on support, I wonder if anybody has another suggestion for me?
In case it helps: ROM version: 1.30.107 WWE, ROM date: 04/11/06, ExtROM version: 1.30.162 WWE
All advice welcome
Thanks
Leapy
extract everything from the exe and do an upgrade without the radio.nbf
did you read what he said? its the radio that's bad and needs replacing
i don't know, sorry
poussin69 said:
extract everything from the exe and do an upgrade without the radio.nbf
Click to expand...
Click to collapse
I am now totally confused.
I know there was a smiley at the end of your comment, I just can't work out if you are being funny or astute (or both?). Can you explain how reinstalling the non-radio ROMs will help? Would that restore the IMEI?
TIA
Leapy
Midget_1990 said:
i don't know, sorry
Click to expand...
Click to collapse
Thanks for responding anyway. At least I am not crying alone in the wilderness.
It would be terrific to find a fix, though.
Try to flash the radio from Buzz's unlocker with MaUpgrade_NoID.exe
http://www.buzzdev.net/index.php?option=com_content&task=view&id=78&Itemid=1
pof said:
Try to flash the radio from Buzz's unlocker with MaUpgrade_NoID.exe
Click to expand...
Click to collapse
Thank you for the suggestion, I just tried as you proposed. "Error 114 - Radio ROM Update Error" *sob*!
It's a real shame. It's actually the ideal phone for my needs.
Leapy
1. Disable Activesync (connection settings -> uncheck "allow USB connections").
2. Put universal in bootloader mode
3. Connect device to computer using USB cable.
4. Start HHD Usb monitor (trial version is OK).
5. File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
6. In the upper part there are two tabs: basic and complete. Click on "Complete".
7. Click on MaUpgrade_NoID.exe and start the radio flashing process, if everything went fine you should see all the USB traffic output on USB monitor window.
8. When radio upgrade fails, click on Edit -> Export and Save as type "ANSI Text files".
9. Save the text file and zip it.
10. Attach the output here or upload it to ftp if it's too big.
Only with this we can see exactly why it fails
Good luck!
http://forum.xda-developers.com/showthread.php?p=994444#post994444
first as recomended i disabled usb from activesync
then downloaded mtty 1.42
connected the usb and started mtty
chose usb
white screen.....
typed set 14 0...
some gibrish on the screen....
ran the rom update....but it informed me that the rom is not for my device...
typed task 0 in mtty (not sure bout the command but its on page 2 of the forum)
ran the update....nothing same error....
now i saw that my universals screen was blank....
removed the battery....and then restarted my universal....
this might help you...
rtask 0/1/3/4
pof said:
1. Disable Activesync (connection settings -> uncheck "allow USB connections").
2. Put universal in bootloader mode
3. Connect device to computer using USB cable.
4. Start HHD Usb monitor (trial version is OK).
5. File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
6. In the upper part there are two tabs: basic and complete. Click on "Complete".
7. Click on MaUpgrade_NoID.exe and start the radio flashing process, if everything went fine you should see all the USB traffic output on USB monitor window.
8. When radio upgrade fails, click on Edit -> Export and Save as type "ANSI Text files".
9. Save the text file and zip it.
10. Attach the output here or upload it to ftp if it's too big.
Only with this we can see exactly why it fails
Good luck!
Click to expand...
Click to collapse
Thank you. I think I did everything exactly as you instructed.
Please find attached the zipped log file.
I would welcome your advice.
Leapy
Radio is corrupted, and device cannot check SecLevel (wait interpreter timeout), it returns default seclevel=FF (unprivileged) and correct CID (O2___001), however when switching to radio bootloader to upgrade the radio, device doesn't answer to any 'rerase' command, that's why the utility gives out flashing after receiving no response to 3 "rerase 0 10000" commands.
Probably this is a bit "crazy", but if it is your last chance... try the following commands in mtty, and try to upgrade the radio again after this:
Code:
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
Don't do it if you can fix your device by any other means (warranty, service centre, etc...) because I'm not sure if it will work or not
Error 114: Radio Rom Update Error
WOW I have the same problem.....
but this commands for mtty...did nothing to my problem.
ERROR 114: RADIO ROM UPDATE ERROR
I don't know if that helps you....on my PDA it says Upgrade Radio Stack Please Wait...
I have the perfect phone....but it is not a phone anymore...and I go crazy.
Is there any way to update the radio rom from SD card??
Please Help
posted reply to incorrect post - cannot delete post - ignore. Please see next post.
pof said:
Radio is corrupted, and device cannot check SecLevel (wait interpreter timeout), it returns default seclevel=FF (unprivileged) and correct CID (O2___001), however when switching to radio bootloader to upgrade the radio, device doesn't answer to any 'rerase' command, that's why the utility gives out flashing after receiving no response to 3 "rerase 0 10000" commands.
Probably this is a bit "crazy", but if it is your last chance... try the following commands in mtty, and try to upgrade the radio again after this:
Code:
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
Don't do it if you can fix your device by any other means (warranty, service centre, etc...) because I'm not sure if it will work or not
Click to expand...
Click to collapse
Well, I too am a little "crazy" so I did as you suggest.
I tried to put Buzz's "unlock" radio v 0.0.0.0 ROM on using MaUpgradeUt_noID.exe. And guess what, it fails again but with a different error!
Error 150: ROM UPGRADE UTILITY ERROR. "This rom upgrade utility is not designed for your device. Please get proper ROM Upgrade Utility and try again!"
I attach the USB Monitor log if it proves any use?
I will try and use the official O2 ROMs and see how that goes.
Thanks again for your assistance, I truly appreciate it.
Leapy
To Leapy...
How did this problem started to you??
I have been using this phone for 1 week, after that I changed my SIM card with another one called MAGIC-SIM card, (programmable) with 8 SIM numbers.
After that day ALL the **** started!!!!!
I had problems during my dialing the number on phonepad...
when I was trying to make a call... it hang up.
After some soft reset...it didn't ask me for PIN.
After a hard reset.... on boot screen it said NO GSM
and then on antenna icon on the top of the screen the antenna had a little x on the right side.
Then the known problem ERROR 114: RADIO ROM UPDATE ERROR
I can update any rom I want but not the Radio ROM
leapy said:
I will try and use the official O2 ROMs and see how that goes.
Click to expand...
Click to collapse
well, I tried the O2 update and just got the generic "CID" error - twice. So I guess I am no nearer fixing this issue...
All advice welcome.
Leapy
leapy said:
Well, I too am a little "crazy" so I did as you suggest.
[...]
I attach the USB Monitor log if it proves any use?
Click to expand...
Click to collapse
Sorry but the capture was from the erase commands... not from the failed radio flash... please try to flash 0.0.0.0 radio again and attach the right capture... also make sure activesync is not running when starting the radio upgrade, and if it fails once, run MaUpgradeUtility twice without disconnecting the device from USB.
my friend got the exact same problem with his EXEC, and send it back to O2, they charge him apprx USD500 for mainboard replacement.....(fiuhh.....)
pof said:
Sorry but the capture was from the erase commands... not from the failed radio flash... please try to flash 0.0.0.0 radio again and attach the right capture... also make sure activesync is not running when starting the radio upgrade, and if it fails once, run MaUpgradeUtility twice without disconnecting the device from USB.
Click to expand...
Click to collapse
Thanks for your continued assistance.
I tried twice with the 0.0.0.0 radio ROM and this time the error has reverted to Error 114 again. With both these attempts, I noticed that the displayed "currently installed" ROM versions were blank - previously I saw the actual on-board version numbers. Not sure if that indicates anything?
Capture logs attached:
leapy said:
Not sure if that indicates anything?
Click to expand...
Click to collapse
That indicates you previously had activesync enabled and now don't.
Exactly same error as before, radio bootloader is not responding when the RUU sends 'rinfo' and 'rerase' commands to it, then the RUU gives up trying.
You can backup the radio ROM from another device with "d2s 60000000 00800000", and theoretically you should be able to load it into yours by using "L" command... but I'm not experienced with universal bootloader and can't say for sure if this will work and the right commands to do it... so please wait until someone reads this and can help you more than me, or research by yourself if you have the time to do it
i wonder if anyone could help me with my problem!
i can't upgrade / Install RADIO ROM (any) in my UNIVERSAL. what happens is that it doesn't starts and when rebooting it says NO GSM where the versions are mentioned in red.
my universal goes in the bootloader mode properly and the update or RADIO ROM Starts; but it stays on 0% and doesn't move ahead. after a while and error comes ERROR 114. Can't update RADIO ROM.
This all happened when i was trying to downgrade my radio rom from 1.14.01 to 1.13.00 this morning and it stopped at 66% with giving this messege.. cannot upgrade radio rom... since then i am unable to re-install radio rom. However i am able to install WIN CE ROM and EXT ROM but not radio ROM.
can you guys help me somehow?
farehmani.
farehmani said:
i wonder if anyone could help me with my problem!
i can't upgrade / Install RADIO ROM (any) in my UNIVERSAL. what happens is that it doesn't starts and when rebooting it says NO GSM where the versions are mentioned in red.
my universal goes in the bootloader mode properly and the update or RADIO ROM Starts; but it stays on 0% and doesn't move ahead. after a while and error comes ERROR 114. Can't update RADIO ROM.
This all happened when i was trying to downgrade my radio rom from 1.14.01 to 1.13.00 this morning and it stopped at 66% with giving this messege.. cannot upgrade radio rom... since then i am unable to re-install radio rom. However i am able to install WIN CE ROM and EXT ROM but not radio ROM.
can you guys help me somehow?
farehmani.
Click to expand...
Click to collapse
Radio rom upgrades are definately more reliable with the original cable. I have read somewhere in these forum that the mode of radio ROM upgrade is different from other ROMs (CE and Ext rom) this is the reason why it takes more time than the CE rom although the later is much larger in size. I suggest you try again if possible on a different PC. For some strange reason I can upgrade my Radio ROM only in my office PC.
d_ranade said:
Radio rom upgrades are definately more reliable with the original cable. I have read somewhere in these forum that the mode of radio ROM upgrade is different from other ROMs (CE and Ext rom) this is the reason why it takes more time than the CE rom although the later is much larger in size. I suggest you try again if possible on a different PC. For some strange reason I can upgrade my Radio ROM only in my office PC.
Click to expand...
Click to collapse
i have tried on 3 different computers but it doesn't work. also with original cable too. it is definately a software problem as no physical damage was made to my device. there must be something that fixes it.
still while upgrading Error 114. (UNABLE TO UPDATE RADIO ROM)
i wish i could find any help with this...
Farehmani
farehmani said:
i have tried on 3 different computers but it doesn't work. also with original cable too. it is definately a software problem as no physical damage was made to my device. there must be something that fixes it.
still while upgrading Error 114. (UNABLE TO UPDATE RADIO ROM)
i wish i could find any help with this...
Farehmani
Click to expand...
Click to collapse
Have you tried putting the unit into Bootloader before you start the upgrade - I find that more reliable?
apd said:
Have you tried putting the unit into Bootloader before you start the upgrade - I find that more reliable?
Click to expand...
Click to collapse
I too find that upgrade in Bootloader is more reliable.
To let you into a little secret.. I ALWAYS flash now in Bootloader mode.. I have only had a couple of "bad flashes" but all of them were direct from a running OS...
I have sent you a pm, that should solve your issue. Please check your pm's...
Take care,
-Jwrightmcps
farehmani said:
i wonder if anyone could help me with my problem!
i can't upgrade / Install RADIO ROM (any) in my UNIVERSAL. what happens is that it doesn't starts and when rebooting it says NO GSM where the versions are mentioned in red.
my universal goes in the bootloader mode properly and the update or RADIO ROM Starts; but it stays on 0% and doesn't move ahead. after a while and error comes ERROR 114. Can't update RADIO ROM.
This all happened when i was trying to downgrade my radio rom from 1.14.01 to 1.13.00 this morning and it stopped at 66% with giving this messege.. cannot upgrade radio rom... since then i am unable to re-install radio rom. However i am able to install WIN CE ROM and EXT ROM but not radio ROM.
can you guys help me somehow?
farehmani.
Click to expand...
Click to collapse
apd said:
Have you tried putting the unit into Bootloader before you start the upgrade - I find that more reliable?
Click to expand...
Click to collapse
yes... i have never tried to flash anything while being in the os. always switch my device to the bootloader first. I have BootLoader 1.01
Please help!!
apd said:
Have you tried putting the unit into Bootloader before you start the upgrade - I find that more reliable?
Click to expand...
Click to collapse
How to put the PPC in Bootloader (Qtek900)?
myname70 said:
How to put the PPC in Bootloader (Qtek900)?
Click to expand...
Click to collapse
Read the wiki - the answers are in there.
apd said:
Read the wiki - the answers are in there.
Click to expand...
Click to collapse
the problem is still there....
i have tried circumvent bootloader password too... and getting error like Win32 Error, Cannot read from the specified device when HEX of password is placed on the memory field of WinDbg.
Tried Another solution for NO GSM but no luck !!
okay here goes; your quoted link had point#5 for no GSM when booting so i followed it as given below.
Pls. see the comments in (( )) for how i conduct these steps and what value is returned.
[[[[--->
Problem 5: Device shows NO GSM when booting (( I'm having this problem ))
1) The radio stack is screwed, you don't get GSM signal and the phone says unknown SIM status
2) Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)
Here is how to fix it:
1)Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections". (( Done! ))
2)Put your Hermes (( Universal )) in bootloader mode
3) Connect device to computer using USB cable. (( Done with Original Cable ))
4) Open mtty.exe and select USB port, then connect.
Hit enter twice, you will see the "USB>" prompt. (( Okay but i usually get the USB> prompt with single hit of Enter ))
Type the following commands (do not copy paste!!!) (( I type them ))
USB> password 0000000000000000 (( Returns: HTCSPass1.CMˆËHTCEUSB> ))
USB> set 1e 1 (( Returns: USB> ))
USB> erase a0040000 c80000 (( Returns: HTCST ÚÈÒHTCEUSB> ))
USB> erase a0cc0000 c80000 ((Returns: HTCST ÚÈÒHTCEUSB> ))
USB> erase a1940000 640000 (( Returns: HTCST ÚÈÒHTCEUSB> ))
USB> set 1e 0 ((Returns: USB> ))
(( Then i close the window of MTTY and proceed to step 5 ))
5) Reset your phone and put it back in bootloader mode (( Here i take my Universal off the usb cable, soft reset it with the stylus and without letting it to boot i switch it into the bootloader mode again and get "Serial & v1.01" on the screen's header and footer ))
6) If your bootloader version is different than 1.04 then Flash Bootloader version 1.04 (( I simply ignore this step as this could be for Hermes users only not for UNIVERSAL Users - Pls. correct me if i'm wrong ))
7) Flash the patched radio used to simunlock the Hermes (( I do it with HTC_Uni_Unlock_v1 it has radio version 0.00.00 BUT still it gets stuck at 0% and after sometime gives the same error 114. Cannot Update Radio ROM ))
Your phone should be alive again (( Its Not ))
<---]]]]
i don't think i'm doing anything wrong here... just the step 5 of bootLoader Update to 1.04...
what comes in your mind ???
i'm desperately missing my pda. its begun to hurt now... please help me rescue my baybee....
farehmani
farehmani said:
i don't think i'm doing anything wrong here... just the step 5 of bootLoader Update to 1.04...
what comes in your mind ???
i'm desperately missing my pda. its begun to hurt now... please help me rescue my baybee....
farehmani
Click to expand...
Click to collapse
Don't worry, mate, you're almost there...
Don't worry about the bootloader version, that is just for the Hermes (Universal will be 1.01 or under for G3, 2.1 for G4). If it's under 1.01 it would be worth upgrading to 1.01 which you can find on the ftp.
SpyderTracks said:
Don't worry, mate, you're almost there...
Don't worry about the bootloader version, that is just for the Hermes (Universal will be 1.01 or under for G3, 2.1 for G4). If it's under 1.01 it would be worth upgrading to 1.01 which you can find on the ftp.
Click to expand...
Click to collapse
glad to know about my being almost there... still i wonder whats keeping me away from retaining my device...
i have already got BootLoader 1.01...
what other method should i apply to get it working again?????
I have the same problem, but not in Universal, but apache, jwright help me.
i have the same problem can smeone help
Try this
"Type "task 28 55aa" and hit enter.
This will restore the DOC partition to its original layout and delete all data
including the ROM!
Once finished you must use the "Original OEM ROM" (i.e. JASJAR WWE
1.30.76) that is made for your device and update with it (CE,Extended
and Radio).
Also if your device bootloader version is lower than "v 1.01" you should
update that first (before installing the OEM ROM, but NOT before "Task
28 55aa").
After this is complete you may then use your device again.
Please let me know how things work out for you...
Take care,
-Jwrightmcps"
It solve me...
i am having the same problem with exec it shows me no gsm and when i go to the device information it does not shows the radio ver and my phone imei is 0 can someoe please tell me how do i solve the problem i had read this tread but not understand it can someone please explane me how do i solve the problem
shedragon said:
"Type "task 28 55aa" and hit enter.
This will restore the DOC partition to its original layout and delete all data
including the ROM!
Once finished you must use the "Original OEM ROM" (i.e. JASJAR WWE
1.30.76) that is made for your device and update with it (CE,Extended
and Radio).
Also if your device bootloader version is lower than "v 1.01" you should
update that first (before installing the OEM ROM, but NOT before "Task
28 55aa").
After this is complete you may then use your device again.
Please let me know how things work out for you...
Take care,
-Jwrightmcps"
It solve me...
Click to expand...
Click to collapse
thanx for your suggestion!
i had tried this already... but the problem is beyon this...
i discussed with pof and he said that somehow i screwed up with the qualcomm chip where the radio bootload resides. so it needs replacement.
anyways... thanx budd... i appreciate your support too...
regards...
my hermes having this problem also ((
hi all,
I am trying to make the radio work again using this procedure:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
but I got a problem and I'd like if someone can help me.
The problem is that I start mtty, I connect the phone in bootloader, I put USB and the I hit twice enter, but the prompt is always CMD>, doesn't change in USB>; I tried many times hitting enter twice, but nothing changes.
How can I do it?
thankyou
Mick
Don't work that's not a problem its just the version of mtty you are using, it should still work.
i am going crazy...I am tring the guide step by step, but when I try tu update radio,it get stuck.
I am with NO GSM and NO IMEI in this moment.
please
help me
(maybe on msn messenger or skype this way I can tell my problems directly)
in Mtty try typing:
task 32
you should get level = 0 to say your device is SuperCID if not you could try the SDcard Method http://forum.xda-developers.com/showthread.php?t=293651&highlight=task+32
thank you markafreeman,
I followed your instruction and I vas able to get level = 0,
but the problem is still that I have Cmd> prompt instead USB.
(can it be a driver problems??)
anyway, I wrote as the guide says:
Cmd> password BsaD5SeoA
Cmd> set 1e 1
Cmd> erase a0040000 c80000
Cmd> erase a0cc0000 c80000
Cmd> erase a1940000 640000
Cmd> set 1e 0
I closed the mtty, restart the PDA on the bootloader again (HERM100, IPL-1.04 Spl-2.10.Olipro) and I sent the official old ROM RUU_Hermes_QTEK_ITA_2.11.258.1_102_6275_1.38.00.10_108_Ship, it starts but get stuck at 13% and then I got on the pc error 262, upgrading error!
I tried twice and it stops always at 13%
UP!!please...somebody give me hope !
I'd probably try the SDcard method I posted earlier at that point.
On some versions of MTTY it shows CMD on some it shows USB, nothing to worry about.
thank you markafreeman:
I tried to do that, but when it start to write radio,it just stops.
thank you drummer10630:
I didn't see any changes in the phones,also if I try with Cmd> prompt
when I go to install RADIO,it stops
Hmmm the other thing I've seen people suggesting with connection problems is on the hermes go to settings and usb to pc and untick the advanceed netowrk option.
mickscores said:
hi all,
I am trying to make the radio work again using this procedure:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
but I got a problem and I'd like if someone can help me.
The problem is that I start mtty, I connect the phone in bootloader, I put USB and the I hit twice enter, but the prompt is always CMD>, doesn't change in USB>; I tried many times hitting enter twice, but nothing changes.
How can I do it?
thankyou
Mick
Click to expand...
Click to collapse
task 28 55aa
then flash again!
Thank you yyyuanye,
I tried your command, it told me that something was formatted, then I tried to re-flash form SD card, but it stops when it's flashing the RADIO.
if you got any idea form me...please...I will be waiting for it.
the Mtty communicate with my Herm because it replies with the coomands Cmd> info, so now it's not a mtty problem anymore.
I don't know, but maybe, in mtty there is a command that erase everything on the radio and make it ready for a new installation.