WiFi not connecting after Dutty WM6 upgrade - 8525, TyTN, MDA Vario II, JasJam ROM Development

Hi All...
My 1st post,, a shame it is about a problem.
Anyway, after examining the 4 WM6 versions currently available I went for the Dutty upgrade.
I followed the Hermes guide to the letter, & EVERYTHING seems to have updated perfectly.
Including my radio firmware being 1.41 now.... WM6 seems to be running like a dream aw well.
However, when i go to connect to my local wifi router, despite it SEEING the ssid, & signal strength & saying it is available etc.... It even starts to initiate.... (my tytn picking up the SSID & channel num etc. ) But it fails to connect (i.e. getting an IP address) & throws up a timeout error.
BTW, my wifi zone has NO security applied to make it easy to connect to - ALL my home PC's etc are all connected & working fine.
Before i upgraded (older radio firmware & WM5) the tytn DID connect.
Strangely enough - Sitting in another room, my Tytn can find another open Wifi router from my neighbour - who also has no security.... when i select this router - the Tytn DOES CONNECT!!! - & I can brouse the net via HIT Wifi - So it does work?????
So what could it be? - something to do with the radio firmware? WM6 maybe? or something subtle with my router settings that didn't pose a problem before, but do now??? - My Router is a D-Link DI-524 - And has been perfect & trouble free for all devices connecting to it for nearly a year.
Anyone have any ideas?
Cheers
Hype

Reset the D-Link, I had A D-Link and had simmilar problems with my notebooks, a simple reset of both devices would solve the problem, I now use a NetGear 802.11g router with no problems ever.

Interestingly, I've just downgraded the Radio Firmware from the 1.41 to 1.40 & It does now want to connect... but still a bit hit & miss.....
As i said above, before any of the upgrades, the Wifi DID work & connect quickly... so this is suggesting that it is the newer Radio Roms that is causing the incompatibility.
Dutty's WM6 is FAB!! - I recommend it highly - In fact more so than the Black 2.5!!!
Hype

Find out what channel and frequency youre neigbours router is and switch youre D-Link to those specs. Basiclly try conecting youre device to it and monitor what channel and frequency it connects to.

Related

Wifi Keeps Breaking!

Hello...
I had Wifi working perfectly on my MDAIII for a very brief period. But it hasn't worked since!
Only by putting the phone into Bootloader mode and starting from scratch brings it back.
It says that it is connected to my network OK. There is very good signal strength. But it only seems to connect once and never again (Internet Explorer says it can't find the page)
I also can't connect to a Wifi point at my local coffee shop, so I know it's not my equipment.
I have tried fixing the IP address but this doesn't work too.
This is really annoying as that was the main reason for getting the damn phone! :evil:
The Wifi unit is a Belkin 54g F5D7630-4A running the latest firmware.
My MDAIII is:
ROM Version: 1.22.00 WWE
ROM Date: 10/22/04
Radio Version: 1.06.00
Protocol Version: 1337.38
ExtROM Version: 1.22.162 WWE
Thank you.
help!!!
hai
i am also having disconection prob with my spv 2000. it conects to the AP (mine is USR9106) and if i try to access any large files from my network the whole system fails.. ie the wireless connection goes off after some time it comes up. tried with different AP but comes with the same prob... some one please help :roll:
I have the same problems with an XDA IIs on a belkin, draytek and bufalo AP. Its not the AP its bugs in the Blue Angel.
Perhaps they will fix it eventually. In the meantime you just have to presevere.
Switching wifi off then on usually fixes, otherwise going into the available networks, I see that its says 'connected' on a network thats 10 miles away, tapping connect for the local network fixes. In many cases, I end up soft resetting.
There are also issues with wifi and DHCP, though I have only seen this twice, it was connected via wifi, but IP config on the wifi adapter showed the last GPRS IP that the unit had!! (GPRS was disconnected).
Nigel
This problem seems to appear after the Bluetooth patch was applied (it doesn't matter whether Bluetooth is on or not).
Turning Wi-Fi off and on again fixes the problem, but it's rather annoying.
My IIs connected to my Netgear unit using WPA without any problems, took a minute to get IP (DHCP).
My problem is that if the device powers off (like pressing button) it disconnects the WiFi, is this the same for you?

Wireless issue - WM6 black edition

Looks like there's some wireless issues here -
I have a Dlink DI-524 b/g router, set to WEP with a small key.
Running WM5 - wireless fine.
Running WM6 Black edition 1.2 - Can see access point, says key is wrong.
Running WM6 Black edition 2.0 - Can see access point, says key is wrong.
Running WM6 XDA live... .20 - fine
Pretty sure XDA live .10 was fine as well, but that was a few weeks back now .
Tried all the settings available, WEP,WPA,WPA2,Hex keys, Ascii keys, no encryption at all..... no go. Can see the AP fine..... takes about 30 seconds before coming back with an incorrect key error.
Anyone else see this?
Sorry dude, Im using WEP 64bit key and works a treat (reception sucks in the loft though)
hmmmmm.
I've tried 64/128 bit keys and everything... perhaps its an issue with wm6/router software. What model AP are you using?
Just tried mine and it works flawlessly...
Maybe try and reset the router/wap?
Been there, done that as well
It's a bit of a puzzle.
It's strange that one flavour of WM6 works and not another. I might have to do a bit of scratching about in the registries/dll's of both and see if there's anything different.
But it's not too critical, as long as one version of WM6 works for me
WPA PSK TKIP running fine here......
No problems with WPA-PSK using TKIP on D-Link DSL-G604T.
Also fine here...
I am using the back 2.0 right now and I have no issue at all.
My settings are:
WPA2 AES RADIUS on a Dlink 2100 AP
from now on... can you please post all issues with Black 2.0 here
Wellll.... I was going to post there, but I was unsure if it was just a WM black issue or a larger one involving other flavours. I did a search before posting and there were hints of similar wireless issues with other roms and other people.
And I've found some sort of solution -
Flashed it back to WM black, finally managed to get it to connect with wpa-2 with an pre-shared AES key. After that, all connection modes work - open/wep/wps.
Will check the registry settings and see if there's anything obviously different now than from the default install.
Funny I was having a similar problem, but it was with WM 6 Black Edition V1.2.
My phone was not finding one of my wireless routers, even when I was standing right beside it, but it would connect to my other one fine. They are both identical and are setup identically, so I dont know why this was happening. It only happened with Black 1.2, XML, and LVSW were fine.
I just now flashed Black V.2 and everything is running fine again.
Very strange... it seems to be the opposite of what happened to you.
What type of router?
I have a router at my office - MN-700 by Microsoft - that causes this problem with all versions of WM6. You will have to reboot both your cable/dsl modem and router and all will be fine. All will be fine until you re-connect your phone via your USB cable and re-sync. After that, you'll be back in the same boat and have to reboot the modem and router.
I have two routers at home - one by dlink and one by linksys - and neither have ever exhibited similar behavior. Therefore, I think it more a router (perhaps firewall?) problem, than a problem with WM6.
I'm now $.02 in the hole....
J
Guy_Incognito said:
Looks like there's some wireless issues here -
I have a Dlink DI-524 b/g router, set to WEP with a small key.
Running WM5 - wireless fine.
Running WM6 Black edition 1.2 - Can see access point, says key is wrong.
Running WM6 Black edition 2.0 - Can see access point, says key is wrong.
Running WM6 XDA live... .20 - fine
Pretty sure XDA live .10 was fine as well, but that was a few weeks back now .
Tried all the settings available, WEP,WPA,WPA2,Hex keys, Ascii keys, no encryption at all..... no go. Can see the AP fine..... takes about 30 seconds before coming back with an incorrect key error.
Anyone else see this?
Click to expand...
Click to collapse
you can
Start->Settings->Connections(Tab)->Wireless LAN ->Power Mode->Best Performance
The Setting is Maybe fine.
There's loads of us happily wifi-ing with Black V2.
I look after hundreds of clients wireless networks... and you may not be surprised to learn that 99.9% of wep problems where it says "incorrect key" are caused by...wait for it... an incorrect key!
Don't cut and paste the key. TYpe it in manually.
However - other options:
Do you have mac filtering enabled on router?
Have you set your device to ask for a specific IP address?
Have you set the device to max performance?
Finally... change the SSID of your home network. All the mucking about you have done may have left some residual mess in the device registry and it is getting confused.
also before typing just check in a word if you are typing the key correct... maybe theres a problem with your hw keyboard... and you don't know it...
qwertz <-> qwerty <-> ??????
IronManDS said:
I have a router at my office - MN-700 by Microsoft - that causes this problem with all versions of WM6. You will have to reboot both your cable/dsl modem and router and all will be fine. All will be fine until you re-connect your phone via your USB cable and re-sync. After that, you'll be back in the same boat and have to reboot the modem and router.
I have two routers at home - one by dlink and one by linksys - and neither have ever exhibited similar behavior. Therefore, I think it more a router (perhaps firewall?) problem, than a problem with WM6.
I'm now $.02 in the hole....
J
Click to expand...
Click to collapse
hmm...i recently upgraded from WM5 to WM6 LVSW0326 ROM and faced this same problem...same setup, same router, same WEP and it worked for a while ...then it died. Refused to connect.
i am sure the WEP is correct as i have the same key on my other wireless devices... and know what is even more interesting? i disable WEP and my device connects ok!
so i know it is not the router or the wifi protion of my hermes, more like the ROM is not sending the network key properly...even after asking for it several times!
anyone has a cab for just the wifi portion?
edit: never had this issue with WM5 even with WEP enabled!
I HAVE THE SAME PROBLEM...
i tried to post my problem in the 1.2 and 2.0 forums, but no one could help ....
i found a weird round about way to make this work every once in a while...
i would go to my network adapters > IEEE wifi adapter > change the specific ip to one that i knew it would work from my router...
this would make it connect, but woudln't work right....
so then when i change it back to "use server-assigned IP"... it would pick up the right address from my router and work .... and all would be fine.... but then when i turned off wifi and tried again, it would fail again.
a problem i see is when it's trying to detect my network, the IP address in the grayed-out box reads (fe80::209:2dff:feef) but when it would work correctly, it would have a normal IP address....
maybe there's something in the writing to the wifi that's different in america???
philpwong said:
you can
Start->Settings->Connections(Tab)->Wireless LAN ->Power Mode->Best Performance
The Setting is Maybe fine.
Click to expand...
Click to collapse
It's work! Thanks!
I did try "This is hidden network" and all the others' suggestions! This is the simpliest and workable method!
Thx again! I can surf by wireless Lan again!
I wonder if MS have seriously reduced the power output on the wireless when its set to BEST BATTERY. It seems a) its set to that by default rather than in the middle and b) quite a few people are having problems with their wifi.
I have Belkin N1 router and it connected fine first time even on low power - and on BEST PERFORMANCE I pick up more of my neighbours SSID's than I used to with WM5
I've had most of the problems listed here.
The new LVSW now has this problem also but Vanilla works fine for me, old LVSW's, XDA Live. Upon changing the protocol the router uses I could connect on the first attempt, subsequent attempts would not work.
I have no trouble with the works router.
This seems to be something other than Microsoft, maybe worth asking LVSW what he did differently on his latest.

Slingplayer Mobile Issue w/Official WM 6 AT&T?

Up until the official AT&T release of WM6 I have been able to use Slingplayer Mobile on my 8525 (both WiFi and over the AT&T network). I recently updated to VP3g's latest. I am able to work fine over local WiFi, but not over the AT&T network. My thoughts are the it's part of the AT&T crack down on MediaMax users (which I am). I don't use it that much over the network, but was wondering if anyone else has this issue since upgrading to the 'official' release.
I have read on other forums that other users are having the same issue. Basically, when working over the network, I get to the 'Starting' and notice that the indicator goes from H to 3G after a few seconds...and then the message pops up.
Everything else seems to work fine, tho I don't have as much program space (20 MB vs 27 MB) as I did on VP3g's 3.0 version.
mac_fan said:
Up until the official AT&T release of WM6 I have been able to use Slingplayer Mobile on my 8525 (both WiFi and over the AT&T network). I recently updated to VP3g's latest. I am able to work fine over local WiFi, but not over the AT&T network. My thoughts are the it's part of the AT&T crack down on MediaMax users (which I am). I don't use it that much over the network, but was wondering if anyone else has this issue since upgrading to the 'official' release.
I have read on other forums that other users are having the same issue. Basically, when working over the network, I get to the 'Starting' and notice that the indicator goes from H to 3G after a few seconds...and then the message pops up.
Everything else seems to work fine, tho I don't have as much program space (20 MB vs 27 MB) as I did on VP3g's 3.0 version.
Click to expand...
Click to collapse
I use slingplayer with vp3g's newest rom. works no problem.
I have MediaMax too. wap.cingular works fine.
Run the disable proxy cab and try it then...
And make sure that your My ISP is set to wap.cingular with [email protected] pw. (for the mediamax workaround without using the MediaNet connection(which I believe has a built in proxy)).
But try the disable proxy...
Thank you for the response. I did try the disable proxy with no change in the result (it installs successfully, but Sling does not work).
I was not implying that it was anything to do with VP3G's version of the new OS...I'm sure it's something that I forgot to do.
I was thinking it might have to do with a recent upgrade from DSL Ultra to Xtreme (where you have a dedicated IP address)...so today I performed the Slingplayer internet access setup again. Tried to access via the AT&T network with the same results...
Locating
Connecting
Starting...
Starting...
Then after about 5 to 10 seconds it goes from H to 3G and and back to H and I get the SlingPlayer popup that says 'Cannot continue streaming due to weak connection. Please try again later.'
I have 3 bars, so I don't think it's the signal...I wonder if something needs to be setup on the DSL modem now that it has a dedicated IP address...
Thank you again for any suggestions.
mac_fan said:
Thank you for the response. I did try the disable proxy with no change in the result (it installs successfully, but Sling does not work).
I was not implying that it was anything to do with VP3G's version of the new OS...I'm sure it's something that I forgot to do.
I was thinking it might have to do with a recent upgrade from DSL Ultra to Xtreme (where you have a dedicated IP address)...so today I performed the Slingplayer internet access setup again. Tried to access via the AT&T network with the same results...
Locating
Connecting
Starting...
Starting...
Then after about 5 to 10 seconds it goes from H to 3G and and back to H and I get the SlingPlayer popup that says 'Cannot continue streaming due to weak connection. Please try again later.'
I have 3 bars, so I don't think it's the signal...I wonder if something needs to be setup on the DSL modem now that it has a dedicated IP address...
Thank you again for any suggestions.
Click to expand...
Click to collapse
Having a static IP should not change your upload speed on DSL. It does however mean that you don't have to enter the million digit finder id for the slingbox anymore, just put in your static ip with the proper port.
Have you always been in the same place when this happened? Always at home perhaps? or work? I'm thinking that it might be a tower issue....hmmm
You of course can use PIE and get on the internet no prob right?
Two bars of signal should be fine, I've gotten it to work on one bar of EDGE before (awful quality, and choppy) so it should work great with that strength..,,,
OK. Try this. From your house try to get on (from the 8525) and see if
1) Network lights on slinglink flash(if you have one)
2) Red lights on the slingbox come on/flash (red network should flash I believe; red led on the "u" should come on if connected
Sounds like you are connecting to the box, but losing connection after the handshake.
Go to www.dslreports.com and do an uplink speed test from your home network. Gotta rule out everything....
Hope this helps.
I had the same problem, but upgraded my slingbox to the next build and it is working again. I'm using a PC, and when I loaded slingbox on my pc it said a new version is available.
I've found someone with the same problem!!
My XDA orbit with WM6 slings fine within my home wifi network but doesn't work anywhere else over gprs or wifi.
Interestingly, it works fine outside my home if I share a wifi connection with my laptop but if the phone connects itself, I get the locating, then streaming then weak connection.
I guess it's an issue with the wifi connection on the phone but quite why it works on my home network but not anywhere else in the world is a mystery!
I have the latest software for slingbox.
All help gratefully received
Jon
Which Slingbox Mobile version are you using? Version 1.2 does not work on WM6 (unless you run the patch floating around here) and version 1.5 does.
Very strange
Very strange. Mine works fine with the ATT WM6 Rom. I have cable so I DNS. Every once in a while i get the issue you are talking about but I just soft reset and then the I connect no problem. In case you want to narrow it down...I use the following:
Slingbox Classic
Time Warner Cable
8525 with WM6 and slingplayer version 1.5
I have verified that the issue occurs whether I'm near home or 60 miles away, in either case going through the AT&T network. I do see the light come on my slingbox pro when the PDA says Starting. I've checked and I have the lastest versions for windows, mac, and mobile. I'm wondering if there is some issue with my router as I do remember having to reboot that a few weeks ago (you can see that I don't use the mobile version that much, but of course now I miss it).
I'll check on the router and let you all know. I did have 4 bars today when testing from home...and as I said it works fine via my home WiFi.
Thank you all for the support, it has been great!
Works fine for me w/ Vp3g 3.62
I have a standard vp3g rom w/ 1.54 radio. My Slingbox pro works fine w/ a 3G connection, but no so good w/ Edge (no surprise there.) I'm even running a wireless ethernet bridge to it - not hardwired. I can't explain why you are having any issues, but do confirm you have the latest ROMs on all your networking equipment, including the slingbox and your Router. Good luck.
Still no joy...wondering if I should re-install the OS...I installed Sling Player Mobile again, removed, then re-installed because I noticed that it wasn't listed under the program list via add/remove programs...I suspected that there was something with the last install...
I re-installed ActiveSync 4.5 on my PC because it was acting funny (would disconnect from my PDA with no message sometimes) that seems to be fine now...
I checked my router...it has a passthru setting for my Slingbox IP address and std port.
My DSL modem has IP Passthru to my router...
My only thought is to re-install the OS which has been a pain because I have Garmin Mobile 10 and have been reloading the maps each time so that they are available...I'll copy the garmin folder from My Device to my desktop, maybe that will remove this necessity...
Any more ideas let me know...
Thank you,
Tim
I ran the mobile speed test on DSL reports, at 400k it said 633/512/437 kbs, earlier in the day it said the file was too small. At 1 MB I got 574/454/499 kbs, earlier in the day it was 791 kbs.
I'm in south Florida, I'm using:
ROM version: vp3G 3.62.3
ROM date: 10/11/07
Radio version: 1.50.00.00
Protocol version: 32.83.7020.20H
SlingPlayer Mobile 1.5.0.98
SlingPlayer is loaded on 2GB storage card. It was working with vp3G 3.60...and 1.50.00.00.
I reloaded the OS and with just sling player loaded on internal...still no joy.
I reset the DSL modem to factory settings and enabled IP Passthru for my router, no joy.
I even set my slingbox in the DMZ, no joy.
I'm wondering if it's something to do with my radio..1.50?
I have another option...besides DSL I have cable and may try connecting the sling box through that...
Any other ideas?
I've verified setup for internet viewing via my PC...
Just an idea... Try orb.com.
I stream my video via a connection to cable on my PC via Orb.
Mike
Interesting findings this weekend. As mentioned previously, I have internet access via cable modem and DSL Xtreme. I moved the slingbox, pc, and router over to my cable modem. Setup everything so that the PC could see the Sling locally and it works fine. When I try to configure for remote viewing, it does not work! I manually configured the router and still no Joy.
I then put the router and slingbox on the DSL LAN and reset the router to defaults (no port forwarding, etc.) Configure everything to work locally, then setup remote network viewing...sling setup thinks all is fine. I check the router...nothing has changed, no port forwarding entries, etc. So I manually configure.
I hook my pc up to the cable modem directly, get internet access and attempt to connect to the sling. It connects almost immediately and then sits on Optimizing for about a minute without any bars or activity going on within the viewer.
I'm wondering if this is a problem with my router...I can run speed tests with multi megabyte files without any issues...
My router is a d-link wbr1310..which used to work...but I guess it's possible that my problem has been discovered...any thoughts?
BTW, I down graded my radio to 1.48 prior to doing all of this and that didn't make any difference which led me to do all of the following for problem isolation.
Thanks for any thoughts...
Tim

Artemis WiFi and Belkin N1 Router

@ all,
it might sound a bit surprising, but I dont get my new artemis ( i now own one with wifi !, my hero didnt!),
working with the wireless of my belkin n1 router!
everytime i enter the mac adress into the router, wlan stops alltogether! ( do i need to enter the mac adress?)
entering the normal wpa-psk passwords into wm6.1 vanilla or b&b5, the connection constantly changes between available, but not connecting, and unavailable... even when sitting right next to the router!
any ideas?
help highly appreciated!
greetz
thormdac
news:
got it working for now-- changed wlan channel in rpouter to channel11, which is preset in wm6.1!
is that how its done?
Update:
most of the times the router just kills the wlan function all in all once i try to connect with the artemis!
Need to reboot router to get it running again!
Where am i going wrong?
p.s. no, i aint a novice
I've got the same roblem mate. Not got a clue what to do ?
Had the same issue with a Belkin N router yesterday. Solution I dumped it went down to Maplins and got a Netgear. Plugin and I was away.
Had flashed the rom serveral times (Win 5, 6, 6.1 some of the cooked roms) nothing worked was thinking it was a hardware failure.
Dont' appear to matter how you set the belkin nothing works.
Thou oddly my Exec connects with it just fine.
Azriaphale said:
Solution I dumped it ...
Click to expand...
Click to collapse
Gee, that would for sure make me one unhappy pal!
Anybody around here has another idea!
Possibly some tips on "Must does" ! for connecting via wifi with artemis! Whats with the mac address-thing?!!!
Greetz
To be honest, I've looked at dozens of sites searching for a solution to this issue. Everything from flashing the ROM (Device and router), enter MAC on the router, set a IP address, changing channels, security settings and nothing appear to work with the Belkin N family.
My experience with Belkin has not been good (Tech support has always been first class).
The first router (Cheap 54g) would run for 2 hours then lockup, requiring a reset of both the router and cable modem). Replaced by Belkin after several days talking to tech support.
The second router (Same 54g unit, different Version number) Ran fine until you moved data about, anything downloading above 150k locked the router. Wired connections could do 300k then lock up. Replaced by Belkin.
The third unit (Upgraded to a 2 stick version for free) DOA. Replaced by Belkin
The forth unit (Same 2 stick version) worked data transfers good but would not allow wifi connections other than WEP 64. Firmware update would then WEP 128. Replaced by Belkin.
The Fifth unit (Same 2 stick version, different version) Wifi worked with all settings. However with wifi on all wired connections ran like a 56k modem. Replaced by Belkin.
The sixth unit (Upgraded to the N) Worked fine. Wired connections fine, wifi was a bit hit or miss, two Toshiba laptops connected fine, the Dell laptop never connected. Belkins own N usb dongle also never connected.
My Orbit never connected to any of the Belkins, the Exec did with some and others not.
This issue is not limited to Belkin, if you look about, other makers routers also appear to have this issue.
The cheap Netgear (£35) works just fine for me. Took 5 minutes to setup. Everything in the house connects. I`m happy after 7 months of Belkin issues.
uiuiui,
what a story!
just so we dont get us wrong here: had my n1 now for about 6months, and its running just fine with all my notebooks! - just since trying to connect with my artemis i am running into probs!
A theory of this mornings trials:
any way of changing the preconfigured broadcast channel 11 within the artemis? --- seems to me the channelchanging is causing the hangups!
will try setting the router to channel 11 and see what happens!
greetz
Ive set channel to 6 in the N router, the Art/Orbit will find it and go though the motions of connecting and make it unavailable (our problem with N routers). The Network setting will show its on ch6 (if you can there before it becomes unavailable). Then goes to ch11.
I think the Art/Orbit just runs in sequence though the channels, if it gets a lock it uses that channel. If not it moves on, I think we just see ch11 because its the last ch available in the scan.
Have just played with the Netgear channels and the Art/Orbit connects with every channel, the Network setting page shows the correct channel that the routers broadcasting.
So it don't appear that the channel is hard coded to the Art/Orbit.
Ok stumbled across this thread a little too late. Our Linksys wrt54g was not able to handle the kind of data we were transferring and moved to a Belkin_N1 router, I have an HTC Wizard but same symptoms, if I try to connect to Belkin I can not connect to anything WIFI before a soft-reset, I get prompted for key fine once and during connection something messes up the wifi radio, I am not sure if its a software or hardware issue but got the same issue with an SMC router, while my D-Link at home is working fine. I wasted so much time flashing ROMs and what not. Thanks for everyone who has put info here, somebody can read here and save the pain of hitting the wall with frustration.

WiFi problem with WM6.1 & Draytek 2820

I've been having troubles trying to connect my JasJam to my new Draytek Vigor 2820Vn router's wireless LAN, and I'm running out of options.
I can connect my desktops and notebooks to the Draytek, but not my JasJam.
I can connect my JasJam to my old Billion 7402VGO router, but not to the new Draytek.
I am running WM6.1 on the JasJam, and had the same troubles with Fario's ROM and PDACorner's ROM.
The Draytek runs 802.11b/g/n, and I have tried it with b&g&n as well as with just b&g. I have turned security on and off, Access control on and off, and everything leads nowhere.
The JasJam will detect the router and show it as available, but it just goes through the motions as if it's connecting, then drops the connection, and the access point changes from "available " to "not available".
I'm looking for ideas, so hit me with your best shot (politely).
hello,
I Have same Problem.
htc touch
draytek router vigor 2820n
boogiept said:
hello,
I Have same Problem.
htc touch
draytek router vigor 2820n
Click to expand...
Click to collapse
I've now lodged a support ticket with Draytek on this issue.
Might help if others with the problem lodge as well.
What I'm guessing is that the router OR phone drops the connection due to an incompatibility with a technology being used by the router.
In the router settings (figured out yourself where)
- Mixed mode protection : RTS/CTS (Gives me stability & range in noisy environment)
- Disable any sort of "performance" tweak/features (Boosting, bursting, any sort of special power mode, whatever)
alkizmo said:
What I'm guessing is that the router OR phone drops the connection due to an incompatibility with a technology being used by the router.
In the router settings (figured out yourself where)
- Mixed mode protection : RTS/CTS (Gives me stability & range in noisy environment)
- Disable any sort of "performance" tweak/features (Boosting, bursting, any sort of special power mode, whatever)
Click to expand...
Click to collapse
Yeah. I've been over this sort of stuff in the router config. Tried turning burst off, and dropping back the 802.11 to b&g only, turned off all security, stood on my head, etc - no difference that I can find.
Haven't looked all that hard at the WM6 registry, though. Was trying to find where WM6 set the frequency region (Draytek shows as Europe, even though I'm in Australia). But I am using the same channel on the Draytek (ch11) as I was on the Billion, so shouldn't be an issue.
Will keep persevering with WM6 unless I get a brilliant suggestion from Draytek.
Hi guys,
I too have this problem with a 3600 & the 2820vn router. Has there been any progress?
Previously, I've got a problem with WM 6.0 and a Draytek 2820 using wifi.
Now, it's solved with a 3.21 firmware (and also upnp disabled on Draytek).
d'oh, beat me to it...i use my wm6.1 with drayteks 2820 and 3120 but i had to upgrade firmware
Hello,
I’ve just bought a Draytek Vigor 2200VG and I’m having the same problem with HTC 3600. Previously it was working fine with SMC Wireless router.
My laptop can connect ok, but when working on batteries I’m having a lot of network interruptions.
Model Name : Vigor2200V series
Firmware Version : v2.6.2_(5)
Build Date/Time : Thu Jan 31 10:30:14.88 2008
Compared to Draytek website, it looks like this is the updated firmware…
Anyone with Vigor 2200V or Vigor 2200VG?
Thanks.
Pedro

Categories

Resources