I was upgrading to the latest version of LVSW when my computer crashed - it's froze at about 54%. I am using SPL (Bootloader) version 1.30.Olipro (HardSPL v4) and now my TYTN only shows the bootloader HERM200 - SPL-1.30.Olipro.
What should I do? Please help.
Paperweight comments are not welcomed
Jean
Jean,
Depending on how bad your situation is, this could involve some work. But at any cost, it would behoove you to actually read the wiki.
Just in case you have completely bricked your device, here is a link that should help you figure things out.
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
The wiki has help for all sorts of situations.
Just another comment though, it is really interesting that you said "Paperweight comments are not welcomed ". But if you do something and dont read the wiki to find answers for yourself (or at least appear to with the kind of posting you did), you will open yourself to comments like that or worse no comments at all.
More information
Here's more information:
1- only the bootloader appears
2- it cannot connect to activesync (so not sure how I can flash anything else as specified in the WIKI: http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick)
3- I do not see any "No GSM" message
I am reading the WIKI and I'm a bit confused. I think since I'm using SPL-1.30.Olipro, I can Flash any NBH containing only OS and restore my OS. I'm able to access my device with mtty.exe - I extracted the latest .nbh from LVSW
Putting the LVSW nbh on a blank microSD card and naming it HERMIMG.nbh and restarting the system, did not do anything. I still see the bootloader. Should I use mtty.exe to try to re-install the latest ROM?
ANY help would be greatly appreciated.
Jean
with this metod select your rom and rename HERMIMG.nbh format your micro sd and put the file.
boot your hermes in boot loader with power(left)+ok(right)+soft reset the flash run.
if don't work please hard reset to try.
and if don't work too, download platform builder ce5 to boot your hermes and follow this thread.
http://forum.xda-developers.com/showthread.php?t=286755&page=39
work only if you KITL ENABLE (power+commanger+soft reset)
IF put KITL SELECT TRANSPORT it's ok if no , hard reset your hermes.
of RabanJr.
pb ce5 can do between 2go at 4go.
jvence said:
Here's more information:
1- only the bootloader appears
2- it cannot connect to activesync (so not sure how I can flash anything else as specified in the WIKI: http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick)
3- I do not see any "No GSM" message
I am reading the WIKI and I'm a bit confused. I think since I'm using SPL-1.30.Olipro, I can Flash any NBH containing only OS and restore my OS.
What software do I use to do this? First I tried using mtty.exe to access my device but it does not show a USB connection even though the TYTN is connected (I even hear a beep when I first connect it).
Would putting the LVSW nbh on the microSD card and naming it HERMIMG.nbh and restarting the system work? I just don't want to do something stupid without some confirmation from the experts out there.
ANY help would be greatly appreciated.
Jean
Click to expand...
Click to collapse
You really need to post this in the relevant thread sir, alot of people keep an eye on the thread and will offer the appropriate help. DONT DO ANYTHING if you need to ask if it will work, first read through the thread, post as instructed in the beginning of it and you will be guided through the unbricking process. I realise this isnt much help but if you do as i suggest you will learn from it aswell
Resolved
Ok thanks for the info. I managed to fix it using the method described in my previous post. I needed to format the MicroSD before placing HERMIMG.nbh on it and it worked flawlessly. Thanks.
jvence said:
Ok thanks for the info. I managed to fix it using the method described in my previous post. I needed to format the MicroSD before placing HERMIMG.nbh on it and it worked flawlessly. Thanks.
Click to expand...
Click to collapse
yes try format your micro sd card if not try this method with pb ce5.0 +kitl
good luck
Related
HI everybody
Like other people on this forum, i'm a linux user
I'm working under Ubuntu Hardy Heron. It's impossible to run any RUU under this system using WINE ( Software than give the possibility to run windows apps under linux ) because it need an active sync connection witch also don't work.
So my request is the following: Can we have a ROM Update utility for our cheer Penguin ?
Big thanks to all developers that works so hard for our community
you and me both: i'm on Linux Mint 5, though
i don't think it's a problem of the people on here: i say it's microsoft's refusing to release drivers for activesync...
There have been attempts made, but i don't know if any of them are going to work with these newer devices... Try googling SynCE...
Hello penguin's friend
SynCE is hard to configure...
But the question is not about synchro, but for ROM updating.
Okay Microsoft is radin... But for upgrading we only need an USB connection for data transfer through the hard SPL.
Activesync is only necessary to retrieve informations from the PDA during an update procedure ( Rom version for example ).
But the flashing procedure doesn't require it ! the prove: when we lunch this procedure the active sync connection stops and the SPL appears on the PDA's screen.
Here is my idea to make it possible under Linux : Run manually SPL on the PDA, and start flashing directly (with USB connection only).
In fact, we only need a ROM Update Utility that pass-through device information retrieving step ( is it really important? ). May be it can works.
All of this could run with wine. But I still think that a native linux RUU is the best way to explore.
There still exist a linux RUU update program (I don't remeber where, but if you make a search into this forum you can find it).
The matter is another one...our diamond don't use the common way to establish a connection with the laptoop ( /ttyUSB0) and so, till now, it's impossible to update...we have to find a workaround for this issues...
I don't understand...
It's the SPL that give necessary connection (usb/serial). Is the problem from it ?
Exactly
Take a look: http://forum.xda-developers.com/showthread.php?t=410302
By searching, i found a solution by flashing from a SD card with a special SPL.
Its solution was developed for ARTHEMIS PDA here : http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Do you think this SPL could work on our diamond ( we don't have SD Card but internal storage ).
I'm afraid to try it. My be it can crash my device permanently ...
GriFolle said:
Exactly
Take a look: http://forum.xda-developers.com/showthread.php?t=410302
Click to expand...
Click to collapse
GREAT ! i go take a look
Sers,
for Linux, HTC Flasher from the link in previous post is what you need.
It's working well for much HTC devices but Diamond still got some connection issues. It doesn't get attached to any serial port in SPL Mode, so flashing via Linux seems impossible.
Even flashing throught Virtualbox doesn't work because it's impossible to attach the device to the VM.
Maybe you're gonna find a solution, let's hope.
regards
demacus
dominique2222 said:
By searching, i found a solution by flashing from a SD card with a special SPL.
Its solution was developed for ARTHEMIS PDA here : http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Do you think this SPL could work on our diamond ( we don't have SD Card but internal storage ).
I'm afraid to try it. My be it can crash my device permanently ...
Click to expand...
Click to collapse
There you're wrong.
Take a look here: http://wiki.xda-developers.com/
In this thread a guy manage to flash Diamond via USB.
OK I have the solution !
It's very simple and don't need any computer!
BE CAREFUL BEFORE STARTING TO HAVE GOOD BATTERY !!!
Install Olinex hard SPL
Connect your PDA to linux in USB Disk mode
Simply copy your .nbh file into internal memory in root folder. rename it to DIAMIMG.NBH
Reset your device with pressing volume down and right key.
You will enter in Olinex SPL flash mode. Wait two seconds and it will ask you if you want to flash from DIAMIMG.nbh !!!
Thanks everybody for your help.
I think this solution is the more simple !
Congrats! Nice find!
This will make things much easyer for many ppl!
regards
demacus
it's much faster than trought async... always used this trick, the only thing to REALLY pay attention to have at least 40/50% of battery
All Right !
Is the file still there afterwards?
Nice find.
Possible to choose from more files?
dominique2222 said:
OK I have the solution !
It's very simple and don't need any computer!
BE CAREFUL BEFORE STARTING TO HAVE GOOD BATTERY !!!
Install Olinex hard SPL
Connect your PDA to linux in USB Disk mode
Simply copy your .nbh file into internal memory in root folder. rename it to DIAMIMG.NBH
Reset your device with pressing volume down and right key.
You will enter in Olinex SPL flash mode. Wait two seconds and it will ask you if you want to flash from DIAMIMG.nbh !!!
Thanks everybody for your help.
I think this solution is the more simple !
Click to expand...
Click to collapse
Thumbs up for you mate! super find, and saves us from messing with external USB hubs ....
Riel said:
Is the file still there afterwards?
Nice find.
Possible to choose from more files?
Click to expand...
Click to collapse
Well.....The file need that specific name.
You CAN transfer other files and name them, but you wont get a "menu" for choosing.
Just turn to your friend, and use his computer that runs Windows.
luzok said:
Just turn to your friend, and use his computer that runs Windows.
Click to expand...
Click to collapse
If prefer working under Linux Sorry Mr Bill !
Penguin 4 ever !!! YeaaaH !!!!
Everything you ever needed to know about "unbricking" your Excalibur but were afraid to ask is in this guide. I've put together this guide for those of you who either intentionally or unintentionally "bricked" or think you've "bricked" your Excalibur.
It is not easy to brick an Excalibur if you actually read and follow all of the steps and guidelines before a flash. In fact, not many things can go wrong unless a USB cables disconnects during a flash, your PC crashes in the middle of a flash, or you flash a corrupt image file to your device. Statistically, most of the time people only think their Excalibur is "bricked" when actually it's not.
There are three methods you can use depending of the severity of the "bricking". The first method will unbrick 50% of all Excalibur's that have simply "locked up" and won't reboot properly. The second method will unbrick 95% of all Excalibur's that encountered flashing problems or flash failures. The third and final method, and the most involved, is a "last resort" for those who have tried method's one and two numerous times unsuccessfully.
** Please perform these steps and methods at your own risk. I am not responsible for any damage you cause your device using this guide.
If you're new to the Excalibur or SmartPhones in general, please take the time to read the WiKi and this post by Stylez for valuable info before you post or try any of these steps.
http://forum.xda-developers.com/showthread.php?t=397583
http://forum.xda-developers.com/showthread.php?t=537151
But, before I even get into unbricking, if your phone is in fact working right now, I highly recommend you flash HardSPL to avoid even having to follow these steps anytime in the future. The steps and info for HardSPL and JumpSPL can be found in this thread by jockyw2001:
http://forum.xda-developers.com/showthread.php?t=329605
HardSPL basically flashes your phone with an "unlocked" security partition so all security checks are bypassed when you try to flash a cooked ROM or a ROM designed for another variation of the Excalibur such as Dopod, HTC, TMO Dash, etc. Makes life much easier when trying different ROMS or cooking and testing your own! Thanks jockyw2001!!
Ok, so onto the fun stuff... Your phone won't boot... Either it's locked up and simply stopped booting or you flashed your phone and it won't boot. What do you do??
Method 1: Assuming you didn't get "bricked" from a flash problem, the first and easiest method for "unbricking" your Excalibur is (this will erase ALL data in your Excalibur):
(This method works for 50% of supposedly "bricked" Excaliburs)
Remove your SIM and SD card
Remove and reinsert your battery
While holding the two softkeys with your thumbs, press the power button
Continue holding the softkeys until a black screen appears saying "This operation will delete all your..."
Press "'send"' to restore to hard reset your phone
Let the phone cold boot and restore
That didn't work!! . This next method will reflash your phone to the factory ROM.
Method 2: Second way to the path of unbricking is:
(This method will unbrick 95% of all Excaliburs)
Get a hold of your Shipped ROM. You can find these ROMS either in Dopod's site, HTC's site (with a valid serial #), TMO's site (http://www.t-mobile.com/wmupgrade/ with a valid IMEI), or right here at XDA at this post (http://forum.xda-developers.com/showthread.php?t=381726)
Download one of these factory ROMS and unpack it. **Remember, if your phone is a TMO Dash, you MUST use a TMO Dash ROM. If your phone is HTC Branded, you MUST use an HTC ROM, etc., etc., etc...
Remove the SD card if one is inserted in the phone
Remove the battery from your phone for a few seconds. I found this step to be essential to reset the device. Put the battery back in.
While holding the camera button on the right side, press the power button. The phone will enter "bootloader" mode and you will see a tricolor bootscreen.
While in this mode, plug in your USB cable and you will hear the "ba-bing" USB sounds as the device connects
Unpack the ROM package you just downloaded and run RomUpdateUtility.exe. Follow the steps, check the appropriate boxes, and start the flash
Assuming all goes well, your phone will flash to the factory ROM and you can then troubleshoot what went wrong the first time that bricked your phone.
Oh no!! That still didn't work!? Or it worked but the flash failed with Error 270 or another error......... Never fear!! XDA-Developers is here! This next method is a bit more intense. It creates a "goldcard" which is used to SuperCID the Excalibur so that it doesn't care about what factory ROM you flash. Please have the factory (not a cooked) ROM ready to go.
** (This method is not intended for Newbie's and some enhanced knowledge of HTC devices and Windows is required to successfully work.)
** (Retry the second method several times with a few different factory ROMS before attemting the below)
Method 3: The third "goldcard" method is a bit more intensive and should be used as a "last resort" so follow closely:
(should unbrick ANY bricked Excalibur if performed correctly)
Get a cup of coffee or tea
You will need a working Donor HTC device with a microSD slot and a microSD card that is smaller than 1GB (will be formatted) to create "goldcard" image using QMAT tools as described below
You will need QMAT. Get it from http://revskills.de/index.html.
Go to the Download link and download the latest version and unpack QMAT
Have some coffee
Use a SD card reader (either USB for microSD adapter) in your PC to access the SD card through Windows. Format the SD card with FAT32.
* Insert the SD card into the donor HTC device and boot up the device. Connect the USB cable and establish an Activesync connection.
Open QMAT and go to the "Hardware Forensics" menu and select "Generate HTC Goldcard"
In "Select device key:" select the Excalibur
You will need the serial number fro the inserted SD card so click the "Get SD Card Serial from WINCE Device" button
Once the Serial number appears in the box, click the "Save Goldcard Image to WINCE SD" button below
If no errors pop up and all goes well, skip the next step
If you get an error or a popup saying "Goldcard for newer devices isn't implemented in newer devices", you must buy and register the software. Believe me, it's worth the small amount of $ you will spend to bring your expensive device back to life!
Now remove the SD card with the newly written Goldcard image from the Donor HTC device
Insert the SD card back into your PC using the microSD card reader adapter. Browse to the drive letter assigned to it. You will see no files on the SD card, this is normal.
(If, for some reason your PC sees the SD card as unformatted, something went wrong. Remove it and reinsert it into the Donor HTC device. The device should see the card as unformatted and ask you to format it, say yes. Now go back to the "* Insert the SD card into the donor HTC device" step above and repeat the steps)
Unpack your Dopod or other factory ROM and copy RUU_Signed.nbh to the SD card. Once it had finished copying, rename the file to EXCAIMG.nbh. Remove the SD card from the PC.
Make sure the Excalibur is off and insert the SD card
Enter bootloader mode as mentioned earlier (hold the camera button while pressing the power button). No need to connect the USB cable.
You will see a gray screen that says "loading". It will then find the EXCAIMG.nbh file and ask if you would like to start the update process. Follow the instructions and let the phone flash.
It will take 10-15 mins but your phone should boot fine and be back in action!
QMAT is a VERY powerful tool written by viperbjk that allows for full low level manipulation of HTC and WINCE tasks. Read all about it here http://revskills.de/index.html.
Many thanks to jockyw2001 for his amazing HTC device knowledge! Also thanks to all who contributed to this post.
Hope this tutorial helps!
Updates and more info will be here.
What if the phone will not enter bootloader mode?
ookba said:
Updates and more info will be here.
Click to expand...
Click to collapse
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
all steamed out said:
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
Click to expand...
Click to collapse
Thanks, glad you like it. Try this guide for your friend. Sounds like an easy fix unless it is indeed hardware related.
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
mydreamisrich said:
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
Click to expand...
Click to collapse
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
alfatech said:
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
Click to expand...
Click to collapse
English is good!! Who is your Carrier? Maybe your carrier has a ROM UPdate on their website? You should be able to use the TMO or Brightpoint ROM. You tried all the factory ROMS and they fail to flash?
ookba said:
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
Click to expand...
Click to collapse
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
aletkd said:
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
Click to expand...
Click to collapse
Yes, your phone is fine. Make sure you follow all of the flashing instructions. Make sure you remove your SD card, connect your phone, run SDA Application Unlock, and run auto.bat from the update package.
mydreamisrich said:
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Click to expand...
Click to collapse
I dont know what you're doing wrong. Sounds like you're not establishing an Activesync connection properly.
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
alfatech said:
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
Click to expand...
Click to collapse
Try the "Goldcard"' method. This should SuperCID your phone and allow you to flash ANY shipped factory ROM. Please follow the tutorial closely. You will need a spare phone with a microSD slot.
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
alfatech said:
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
Click to expand...
Click to collapse
No, just has to Windows Mobile based and have a SDHC slot.
OK. I try with 3rd method and when run Qmat and select "Get SD Card serial from WINCE Device" appears the message "You need to set rigth registry permissions. See QMAT manual for more info." and not recognizes the sd card.
What is the problem?
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
alfatech said:
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
Click to expand...
Click to collapse
GREAT!!!!! Congratulations!
I tried but when I click Get SD Card Serial from WINCE Device in the box none found and click Save Goldcard Image to WINCE SD is card ID isn't 16 bit (32 charter) long. I isn't succesful. help me???????
HI,
Im having problem installing a new ROM wm 6.5 to my touch diamond1. I tried doing the installtion from my internal storage. I renamed the new ROM already and place it in my internal storage and tried to install from there. I have a hard SPL Olinex 1.4 or 1.37.
after I pressed the lower vol+back button the red/green/blue screen cam and then a gray screen asking for movihand.mtg and after that it loads another gray screen saying loading.............. for a long time.
If anyone has encountered this problem need assistance.
Im trying to install deepshining ROM ver 8.
Thanks,
You need unsigned hard_spl like the Olinex 1.40 or 1.93
see this post:
http://forum.xda-developers.com/showthread.php?t=416211
do not forget to use the search option
things i found to check:
do you have the hardspl 1.93 (are you sure)
try deleting the files on your internal storage (or copy them to your computer) and only put the DIAMIMG.NBH file in the root
try it with the customruu.exe if it stays at 0% for too long, something is wrong, probably with your hardspl
put your device in bootloader (rgb screen), connect to computer, on the bottom serial should change to usb. try using customruu.exe.
you need to have the nbh file in the same directory as customruu offcourse.
maybe a not so nice remark. sorry in advance:
but if you have so many problems why try flashing at all? i can guarantee you that you will run into problems using custom rom's. you will have to do a lot of searching and trying to find solutions. the manuals about flashing are already in the forums. and working for everybody else. so you are probably doing something wrong.
I would suggest that you search a lot more and longer and list everything you tried. you are not the first to run into problems, and you will not be the lasts.
good luck
thanks I will try again thanks for the advise.
Hello hello
I'm quiet noob in english and android ^^.
Since 2 days i'm trying to install froyo on my device!
I can't flash my device! I tried many differents .nbh files but no changes
I really need your help!
I'm following this tutoriel: http://forum.xda-developers.com/showpost.php?p=10424799&postcount=451
And this android version:Incubus RS16
this is the .nbh file used: http://it029000.massey.ac.nz/vogue/files/?C=M;O=D
This is the screen i got when i try home+camera on boot: http://img713.imageshack.us/img713/4931/dscn2273.jpg
If you have questions..... Thanks for your helps!
Use this guide.
http://forum.xda-developers.com/showthread.php?t=680518
its better to download the latest KAISimg.nbh from ATools.
and make sure you have formatted your sd card to fat32 , in order to flash the kernel and install everything without errors.
Follow the guide in atools help.
Thanks for yours link
I follow them step by step but i still have the same problem!
It's amazing pls help me guys! i really need my phone.
hardspl 3.34 is ok Radio is ok
I follow atool tuto step by step.
When i put the sd card in the mobile and open the bootloader, the 3color screen appears net the white screen but he disappear in the last second
Any suggestion?
Verify the filename or maybe it could be a sd problem (try with another one)
Don't flash with SD, use USB instead. My Kaiser refused to work with SD, but works perfect over 50 flashes later with USB. I am using Windows 7, I just plug the kaiser in and let windows detect that something is there. Then I download the update for WM device center or whatever they renamed activesync to since vista lol. Afterwards it will detect well enough. Once it does I use RUU custom and just flash it over usb with that Kaisimg file. Not a well written guide I know... I can at least send you my ruu custom if you need it.
thanks for help
I'm under XP. I install active sync but inpossible for my device to be connected on the pc.
I'm losing my head lol!
levitz_kais said:
thanks for help
I'm under XP. I install active sync but inpossible for my device to be connected on the pc.
I'm losing my head lol!
Click to expand...
Click to collapse
as per your screen shot. you phone is in boot loader already.. active sync only detects phone wen its running windows.. you dont need to sync your device with active sync when its already in boot loader.. just connect it with pc and run update utility of windows rom u want to have on your phone.. or update utility with android kernel to boot android in it.. your phone will be working in no time..
Yep Activesync will see something is there but it isnt a WM device basically. That is good enough to let RUU Custom work.
Thanks guys i'll try this in the minute!
EEdit: it won't work can you explain me more how to install android with RUU custom? pleéase
levitz_kais said:
Thanks guys i'll try this in the minute!
EEdit: it won't work can you explain me more how to install android with RUU custom? pleéase
Click to expand...
Click to collapse
Format your SD Card in FAT 32
use HP USB Disk Storage format tool (find it somewhere over google)
Edit: http://files.extremeoverclocking.com/file.php?f=197
and make sure that the nbh is renamed as kaisimg.nbh.
For instance only put the nbh on your SD card (nothing else) and try flashing.
I am using HSPL 3.59 and its going good. (before that it was 3.34 and never caused any problems) Radio Version 1.70.19.09
hey guys
how could me remove linux from my kaiser?
help me please
If you have your WM rom, you need to change it's name to KAISIMG.NBH and copy it to root of your sdcard, then you should be able to install it from your bootloader.
If it doesn't work, you can go to bootloader, connect your device to computer with USB cable and then flash with RUU just like you had with WM, it will go straight to flashing instead of checking battery level etc like it was when flashing with booted WM.
I hope you will understand me
Thanx for the reply
i tried the two ways but with no result
it's hang up at 1% in the case of using usb
and hang up at (loading...) in the case of using sd card
if there is any way else please help me
sorry for my bad english
thanx again
msichal said:
If you have your WM rom, you need to change it's name to KAISIMG.NBH and copy it to root of your sdcard, then you should be able to install it from your bootloader.
If it doesn't work, you can go to bootloader, connect your device to computer with USB cable and then flash with RUU just like you had with WM, it will go straight to flashing instead of checking battery level etc like it was when flashing with booted WM.
I hope you will understand me
Click to expand...
Click to collapse
I'm pretty sure he also needs a corresponding WM kernel to go back to winmo.
read this ..the section that will interest you is at the end of opening post.
http://forum.xda-developers.com/showthread.php?t=680518
Hi,
I think I followed all instructions to switch back to WiMo in the sticky thread.
For a second the display shows a screen with four colours:
KAIS130
SPL-3.34.0000
CPLD-8
Then the screen turns to grey showing:
Loading ...
but nothing else happens.
Data on my sdcard:
KAISDIAG.NBH form the sticky thread
KAISimg.nbh (renamed RUU_signed.nbh) form rom file from this thread:
forum.xda-developers.com/showthread.php?t=379554
Do I have the right files on my sdcard?
My phone: Vodafone 1615 from german
Any suggestions?
thanks,