Related
Folks:
My PDA2k stylus has become too loose and I am starting to drop it everywhere: my pockets, my car, etc. In all likelihood, if I don't find a solution pronto, I'll be using my fingers because of a lost stylus.
Is anyone out there having this problem? How do you deal with it?
Thanks in advance.
Fernando
my XDA2s is getting worse, its 2 months old and gets used, give it another month and i be needing to get a big big box of replacement stylus's
Stylus problem? no problem.
Hey guys!
I'd just leave the regular stylus in my MDAIII and I went and got these check it out : http://www.truetip.com
They have all kind of stylus stuff that may can work out for you. I bought a few :wink: of each and I hardly every use the one in my unit. I hope this helps, Take care fellas! :wink:
I've just encountered this problem and went the "Classy" way with my solution.
Magic tape wraped twice around the top of the stylus. Fingers crossed I'll have no more retracing my steps fun looking for a missing stylus. :lol:
hmmmn just put (stick) small neoprene inside the hole (opening)....
[5561 004.jpg]
[5561 006.jpg]
thanks,
jojo
Or just buy some more styluses i bought 3 from here and recieved the item next day. I'm also going to buy an xda2s handsfree from him as i have lost that 2.
http://search.ebay.co.uk/_W0QQsassZairportinfo
expansys.com has a lot of different kinds of stylus for PDA2K or similar. there are regular and with pen included.
expansys has offices in diferents countries. check yours.
Tano
Leave it in for service, it's the only way that HTC will understand that they need to go up some notches on the Hardware quality.
There is no way I'm taping anything on a 1.000,-$ unit
Mine is headding for service once more in the near future.
tano said:
expansys.com has a lot of different kinds of stylus for PDA2K or similar. there are regular and with pen included.
expansys has offices in diferents countries. check yours.
Tano
Click to expand...
Click to collapse
these ones are original styluses
http://search.ebay.co.uk/_W0QQsassZairportinfo
There is no way I'm taping anything on a 1.000,-$ unit
Click to expand...
Click to collapse
Good point. This thing cost more than my old car. Just whilt we're on the topic of hardware that was clearly not tested thoroughly before it as marketed, does anyone else's sliding mechanism scratch the keyboard?
yep on the left hand side. and i hardly ever use the keyboard so its not down to wear and tear.
to be honest the xda2s does feel cheap when its on your hand.
scratch on the left side of keyboard... hardly used the keyboard though...
and a gap between the lcd and battery slider on the right hand side...
I fixed mine with a single layer of tape around the top of the stylus. Now just enough grip to hold on.
rich
Mine went back to the O2 service centre on Sunday! The slider was never right from the day I got it (this one was my second) and I lost a stylus the other day. The sliding keyboard was so far away from the chassis I could see daylight through it!
I also had the "wear" makes on BOTH sides of the keyboard and the Sales assistant said that they ALWAYS get those on every unit they get back, which I'm told is quite a few!
I'm waiting on a response from them as I suspect as before, they will just give me a brand new one. Anyway, I'm thinking of Ebaying the XDAIIs and getting myself an Orange c550/Qtek 8200 (HTC Robbie) Smartphone as I'm not impressed with the build quality compared to the XDAII/IIi!
We'll see!
Dom
Loose stylus - Stylus falls out
I dropped my BA 5 meters onto a concrete floor. It landed on the corner and bent the corner in. I just picked it up and it still worked. I use it in a industrial enviroment so it looks ugly, but always works. My old Ipaqs couldn't handle a one meter fall onto carpet without cracking the screen.
Oh yeah! Here's the fix to the original problem on this thread. It's really a easy fix. It's been 5 months since I lost a stylus.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-If your corner is bent straighten it now(see above)
-Reassemble BA
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade!
Good Luck,
N2O2
The Low-Tech Way
I crammed a little wad of paper into the area between the case and the little plastic spring. Works like a charm!
:? Boy do I feel dumb.
I've been using a 3-1 stylus (from Proporta) on my M2K and today the plastic "tip" got stuck in the unit's slot! Peering down the slot using a desk-lamp I can see the tip and it's off-centre to the actual axis of the hole. It looks like the hole for the stylus is NOT a tube - but is instead merely an opening into the unit. (thinking about it - I'd noticed that the stylus tip was "awkward" to fit into the slot a couple of times - obviously it had been getting caught in the body-work).
Stupidly I've further compounded my troubles by attempting to fineagle (technical term.. ) the tip out by using a biro refill - and the tip of the biro refill got stuck in the stylus tip!!! AAARGH! :shock:
Looks like I'll need to dismantle the entire bloody unit to get this thing out - so... how do I do it, what do I need, and where can I obtain the tools??
DOH!!!!
Damm, your having one of those day's
Just as a side note.
Don’t buy or use 3 in 1 stylus, they will break the clamp in the device holding the stylus in place so the stylus gets so loose that it will slide out and in without any resistance
Check your warranty before taking your unit apart!
You'll need a T6x60 and maybe a T7x60 drive. Then search for a thread on this forum that will guide you through the dismantling process.
good luck!
nomadman said:
Check your warranty before taking your unit apart!
You'll need a T6x60 and maybe a T7x60 drive. Then search for a thread on this forum that will guide you through the dismantling process.
good luck!
Click to expand...
Click to collapse
somehow I doubt Orange will be terribly impressed with what's hapened!!!
Anyone know how much it would cost to have the unit dismantled by a repair workshop (and thus maintain the warranty)? And is there such a place in central London?
Why not try the finest tad (more technical phraseology) of super glue on the end of your 3 in 1, push in hole, wait 1 minute and pull out. It might just work and surely would have done without that biro bit. Got to be worth a try - but be frugal with the glue !
By the way, I've used a 3 in 1 form Proporta for 3 months now and the old stylus fits and is retained just the same as its always has done (just tried it).
Stylus.
Hmmm I dont remember where i bought mine, but this is the second time i need to get the 9090 to service.
There is no resistense at all, it just slide in and out by it self
They are going right to the trashbin now.
Do you have a link to where you got yours??
Bottom stylus is the original.
Much more soft in the area where the clamp goes in
Mine came from here;
http://www.proporta.com/F02/PPF02P05.php?t_id=933&t_mode=des
But having looked at your photograph, and had a good look at my stylii, the 'shoulder' is different on my original stylus and that from Proporta - just as your picky shows. Still haven't had a problem though - YET.
Don't like it that you have to take of the tip to use the pen as reset tool
The ones i got are working very good, but I just cant use them any more since they destroy the clamp.
Here's one more pic.
I don't. I just use the tip of the stylus for re-set.
If you pull out the stylus and look into the hole in the BA, does it look like white plastic clamps in your BA.
I can se 2 white plastic clamps in mine.
Yes - just the same !
Since we both have plastic clamps, my stylus clamp shoulders must be the reason for the defect in the BA.
Well then I can only say to anybody reading this thread, don't buy 3 in 1 stylus that look like the ones in the pictures :!: :!:
TIP: Use a software to reset the PPC. I use CLaunch on normal reset. During lockups, I have to use the stylus. But that's only 1out of 10 resets.
http://home.pacific.net.sg/~welic/claunch.html
nomadman - sir, sorry this is out of the topic.... i just noticed your ROM version... where did you get the ROM update for our XDA IIs?
Thanks!
YAY! Fixed it last night.
1 T6 driver and 1 small flat bladed screwdriver were all the tools necessary.
Just removed the 2 silver screws, and 3 of the black ones (the "Void" sticker was untouched) and the rear cover was loose enough to allow the very flat blade of the screwdriver in just far enough to dislodge the "item" and it just dropped out.
reassembly was easy and the only shock I got was when I turned the unit back on the emergency battery was nearly dead!! I'd only had the main battery off the unit for 5 minutes!!!! Not terribly impressed by that I have to say.
Hi guys, just wondering if any users out there are having the same problems as me. ive had my Blue Angel now for a good 6 months and im very happy with it appart from it doesnt ring which is very very annoying :twisted: anyone know a fix for this?
But main reason for this post is; has anyone got the same problem that the holder for the stylus has become used and now doesnt hold the stylus in place anymore? i remember there being a click when pushing the stylus in. but now it just falls out when i tip the PDA upside down.
Anyone whos opened up a BA can you give any details on how the holder works? can it be modded so that it grips the stylus again? im one for opening up electrinics and playing with them but since i use this for alot of my work i cant risk it.
many thanks for any replies.
DJUPLIFT
I have the same issues. I tried to take mine apart but could not seem to separate the back side of the case. I removed 3 screws from behind the battery, and one from either side of the device. I too would like any input.
It totally blows... cos i always end up taking the phone out of my pocket and sometimes i dont hear the stylus drop. ive already lost two like this... it might end up being more expensive to just keep buying stylus than to open the BA and screw it up... All in all my ones been opened already :shock:
i dropped it on concrete and somehow the touchscreen stopped working although the screen was intact. O2 replaced it with a brand new one for diddly sqwat!! FANTASTIC!!!
i might just take it appart next weekend and have a little look inside see if there is a way to access this comparment and maybe doing a little DIY style modding!
if i come up with any conclusions ill post them with some pics of course!
DJUPLIFT
a friend of mine took his apart and there does not appear to be a way to tighten the stylus. He said it was just a small plastic protusion that held it in place. Once it wears, you are out of luck. Have not seen this myself, but thats what he tells me..
Regards
chris
that's correct, it's just a plastic clip protruding to grab the gap on the stylus. if it's broken, you may just have to put a tape or sticker around the stylus to make it tighter.
there are 4 screws (one under the void sticker) where the battery goes. i just took mine apart to tighten slider. it's back to sliding smoothly & tight, however, there's still a noticeable gap (between the screen plate & keyboard plate).
anyone knows how to eliminate this gap (about 2mm)?
Try this solution: http://forum.xda-developers.com/viewtopic.php?t=15120&highlight=loose+stylus
Cheers
Frankman
I use 1 layer of tape around the stylus. spanning the groove in the stylus. This seems to make it a good bit tighter, but does not fix the problem entirely. Hope that helps..
Regards
Chris
i dont like the idea of having tape on my stylus... looks well tacky going into a metting with clients!!
so i took some black insulation tape and made small squares with an art blade and stuck them to the inner edge of the holder... now it sits there nice and tight like a school girl
S O R T E D!!!!
cheers for the help guys/gals.... if any....
An idiot friend of mine put a blade of grass in the stylus holder and now it wont come out. How do I fish it out? The good thing is, my stylus doesn't slide out so easily anymore.
I have also encountered this problem(i got my BA 6 months till now), however it is not that loose as what ur described. at lease it never drop out when i was outside. (after reading this i become worry about it)
I used to own a IPAQ 5550, when i got my BA, i thought the quality of the stylus is better than ipaq's plastic stylus(should have some heavy stuff insde..), i like the BA's metalic stylus.
Now i found that the IPAQ plastic stylus + the spring-like system inside the whole is much better...i want to have one BA + the metalic stylus + the spring-like system to hold the stylus....
if some day i am that unlucky to lost my BA's stylus i will try to use the 3-in-one PDA pen... once it lost one, i may lost another... i wont use normal stylus if it happened.
DJUPLIFT wrote[/quote]
i dont like the idea of having tape on my stylus... looks well tacky going into a metting with clients!!
You have to use that "invisable" tape and only the keyboard and buttons if its a Director or above! :lol:
Click to expand...
Click to collapse
Loose stylus - Stylus falls out
This has worked for me. It's been 5 months, and it still works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Reassemble your BA.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Yet again we're having to come up with dodgy (although well thought out) solutions to HTC's shoddy design flaws. My BA is about 3 - 4 months old and its up to this already. I keep finding my stylus on the floor.
Thing is, all these solutions void the warranty and I have to take mine back soon (See the Xray thread ) and am hoping for a replacement on insurance.
The P800 and XDA2 had this problem as well, but surprisingly I have NEVER lost a single stylus in my life! I always just happen to find them again. One time I found my P800 stylus 2 days later in the street between my college and my flat :S
Re: Loose stylus - Stylus falls out
N2O2 said:
This has worked for me. It's been 5 months, and it still works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Reassemble your BA.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Click to expand...
Click to collapse
Great idea! It's perfect!
THANK YOU N2O2
N2O2
You just made the wiki hall of fame
http://wiki.xda-developers.com/index.php?pagename=BA_Sty_stopper
Any Kentucky Fried Chícken fans out there?
After losing 5 styli - not only because they were loose in the holder (one went on the motorcycle after I missed the holder hole and then let it go) I came up with this junky solution.
The KFC corn cob holders are a good diameter (had to add a thin layer of tape) and just long enough to be modifiable to add a knureld part at upper end. At at least one of their restaurants I found them outside of the front counter and was able to obtain a few cheap spare emergency styli
Oh well.
:lol: :lol: HAHAHAHAHA You are grade man .....
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
Lost another one from the new phone in the few hours since I posted the KFC thing.
Uuuups - time to go out for a buckt of the Colonels finest.
I am having probems with my touchscreen and want to pull the case off it so that I can check connections.
The service manual states that after having undone the screws along the bottom edge of the screen that you should use a screwdriver to push into the hole in the bottom left hand edge of the screen case to release the catch to separate the two halves, but pushing the screwdriver in there doesn't seem to release anything.
Has anyone here managed to dismantle the screen and have any tips on how to do it?
:lol: youv'e probaly sorted by now
anyhow ur need to obtain a plastic ended screwdriver (unless you fancy damaging case) insert at join wilst using a fine screwdriver, gently push in hole lever outwards while prising and i'tl 'pop' out do same at other end and use plastic srewdriver to pop open along join all around until it pops of.
had to change screen on mine took about 25mins total, advise u use anti static wrist band (lot of sensitive stuff near screen).
Where did you get your screen from? and how much?
:lol: i brought unit off ebay (internally damaged) for the screen (lucky). theres a taiwanese company, selling them, but not seen on ebay for a while, if you look through archives theres also a usa company, but only repair.
Hi,
Just had an MDA Pro screen replaced by these chaps in Wimbledon:
http://www.xdarepairs.co.uk
Cost quoted was about £110 +VAT + Postage fitted, or £90 +VAT for the part on its own. All in, the screen, including fitting, was not much more than the screen on its own from ebay.
Posted to them on Tuesday at 16:45 and received back on Thursday at 08:45. Working beautifully again.
May be worth a try.
I'm OK with taking things apart and putting them back together. Are there screen shots of someone taking the Blue Angel apart and fixing the stylus clip?
Please post
or even a video clip?
DIY Blueangle fix
Hi,
I had been using HTC BlueAngle for almost 2 years and very happy with it.
When I first got it, I dropped it the next day. The stylus holding clip was broken off. At first I tried to put tapes around the stylus to hold it in place.
It didn't work out at the end and I opened it up and put a piece of foam in the stylus tube to add fiction and avoid it fall out. I worked nicely.
I still love my BA even I am using HTC Universal most of the time.
Cheers
I have the same problem. Nice tip, thanks, I'll consider it too.
u dont have to do all that, the main reason it becomes loose is the bit of plastic that is attached to the frame gets weak... just open the back with the specialist screwdrivers which can be bought off ebay for nomore than £5 and either superglue it back into the correct place or just rest something like paper to make the plastic bit stick out a bit more so that the stylus gets a tighter fit....
go for the quick fix...just stick a 3mm width masking tape on the top part of the stylus and it is good to go. adjust the width of the tape according to how tight you want your stylus to be in place. HTH