asus P525 seems to be dead ? - Upgrading, Modifying and Unlocking

i had purchased the ASUS P525. unit is less than 6 mnths old.
whilst i was using the calculator, it just switched off.
It does not start.
it does not reboot, does not respond to hard reset.
i have tried removing the battery.(which was about 50% charged before issue)
i have tried plugin in the charger, no change, is dead, except the green light comes on when plug into charger.
i have tried reset button(no effect)
effectively the unit is dead right now,
zero respose or operation.
its basically dead
Anyone faced this before ?
Any ideas ?
please help
thanks

Have you try to make a Hard Reset?
(with the joystick up + reset)
Best Regards
fernando

hi fernando,
yes, i have already tried the hard reset, and still no response.
still lifeless
any other ideas \sugestions ?
thanks

try holdin ur power button for a long time.....

I dropped my Asus P525 while biking and now it doesn't respond to anything I do with it (removing the battery, soft reset, hard reset, long press on power on button). When I plug in the charger, the indicator light lit up and turned to green after a while which means that it can still charge the battery.
I tried to take off the battery for a few minutes and after inserting it back, the blue Asus welcome screen was shown but then it went blank again and doesn't respond to any keypresses again.
Is my P525 dead already? Anything else I can do?

Related

Universal Died while upgrading

hi
i was upgrading my universal, following instructions from http://wiki.xda-developers.com/index.php?pagename=Helmi
after upgrading, on my computer i received an error saying the upgrade was unsuccessful and now my universal is dead
i tried hard resetting, i tried putting it into bootloader mode...
there is nothing on the screen
what should i do?
have you ever entered BL before? most new users would not realise their in BL as it doesn't have any backlight. look closely
yes, i have, it isnt working at all, there is nothing on the screen
when i try to flash the device the pc says error 101 connection error
does your charge light appears when connected to AC power?
nope, no charge light
its sad just about 3 hours ago my device was working perfectly
here's what you do:
start activesync on your computer.
Go to connection settings and deselect allow usb connections.
connect your uni to your computer and push the backlight + on/off button and hold these. Then press the reset with your pen, still holding the backlight and on/off.
The screen should say something about serial or usb.
The backlight will not be lighted so it's hard to read.
If the screen doesn't say anything, unplug and plug in the usb connecter one more time.
Does your red charge led lit when you put it on the wallcharger ?
i tried that, many many times, screen still remains blank
nope, no red light when i plug it into the wall
this is bad, its not responding to anything
When plugged, does it give you a red blink (Charge light) when you Soft Reset?
yes!
yes, the first sign of life, when pluged in via usb to the pc, when i soft reset i get a red blink
any ideas?
Try holding down Light + power for at least 5sec. and while still pressing, do a soft reset.
If you dont go to BootLoader then try to increase the Hold down Light + Power some more.
And BTW. dont get stressed, keep cool.
Youl just **** it even more up if you get stressed, Ok
k, i just tried that, everytime i let go fo the soft reset button the pc says the usb device is not recognized, but still nothing on the screen
lol yeah ur right
thanks for the help
NP. now run the original upgrade for your device...your device is in boot loader right?
nope no bootloader, the screen is completely blank
sahir said:
nope no bootloader, the screen is completely blank
Click to expand...
Click to collapse
Look closely, it wont have backlight on, so look really closely.
Remove the SD card and Sim, and just keep trying different time intervals with the "holding down Light + power for at least 5sec. and while still pressing, do a soft reset."
And if you had low battery when you started the upgrade, the use your Wall charger, not USB charger...and let it stay in for 1/2 hour before proceding.
Keep us updated
i removed the sim and sd, and have tried many different intervals, i charged the device all night last night with teh wall charger, still no luck
Hmmmmm, this is a bit strange.
The exact same thing happend to me some 5 days ago.
I managed to get it back with this trick.
Try Soft Reset between every try....just hang in there suddently it wil come to life
Do a ATX-reset/Destat.
Remove charger, battery etc and push in on/off button for 30sec twice. Then push down as many keyboard buttons as you can for a little while too. This way you "drain" it and everything should be reset. Try again.
Works especially well on computers that don't wanna POST. Same thing with cellphones, TV's, remotes etc.
ATX-Reset/Destat. Remember that one. Can solve loads of glitches.
How do I know?
Don't ask I work with these kind of issues every day.
i just tried the atx reset destat idea, it didnt boot it up
ive tried many different intervals now, ive spent hours trying to get this to work
bosjo were u connected to the pc while trying to get it into bootloader?

Is My Tilt 2 Dead?

I checked email then I sent a text. A few minutes later, I got a response. I hit REPLY and the screen went white. I don't know why. It's never been dropped or put in water, etc. The phone had been in my pocket all day and was close to a full charge. I couldn't power down so I removed the battery and turned it back on. The phone vibrated as it does when it boots up but the screen remained black. I flipped out the keyboard and it was backlit as usual.
I tried a few times and never got anything going. The screen remained black but the phone got hot. Just now, I noticed the amber light blinking but it went solid when I plugged in the charger. I attempted to power it up once more and called from my landline- goes straight to voicemail, no rings. Hmm. Is my Tilt 2 Dead?
Any advice on how to resurrect my phone? AT&T gave me this refurbished model about 4 months ago (60 day warranty?) to replace the Fuze that died at 13 months (12 month warranty). I just want a phone that can last as long as my contract.
try to put it in bootloader mode.
do this by holding the volume down button and powering on the device (if its already on then volume down button and press the soft reset button on the side of ur device with the stylus). Keep holding the volume down button until the 3 colored screen comes on with text in red.
if you can get it in bootloader than you can save the device
Sometimes mine hangs on startup several times in a row, to fix it, i take out the battery, put it back in, hold down the power button and volume down button till its in bootloader then soft reset with the button on the side of the device and it boots up
if that doesn't work then you may need to hard-reset/flash a new rom (all your data will be erased). If nothing comes on the screen then your screen could be dead.
I charged it all night. When plugged in, the amber light is solid. When unplugged, the light turned off. The phone doesn't power up.
It did not respond to a soft-reset (holding the volume down button and powering on the device) nor a hard-reset (press and hold both the send and end hardkeys).
AT&T is telling me it's dead. Um, I've got a different ROM loaded on this. Can I return it in this state? If they cant resurrect it, it doesn't matter?
Do I need to restore factory settings and, if so, how?
And, Warranty Dept. wants me to buy another one. They gave me this refurbished one four months ago with 90 day warranty. What are my chances here?
cam123 said:
I charged it all night. When plugged in, the amber light is solid. When unplugged, the light turned off. The phone doesn't power up.
It did not respond to a soft-reset (holding the volume down button and powering on the device) nor a hard-reset (press and hold both the send and end hardkeys).
Click to expand...
Click to collapse
If the indicator light never went green, the battery may be at fault. Just a thought.
I have heard of the black screen that comes up and ppl have to soft reset to get anything to work. Never had this problem till lately. My fone was on and plugged in all nite. Never had a prob with the battery, only had this fone 3 months and now all nite and day the screen has been goin black then not waking up at all. I did install Cookies Home Tab and the CTHE Editor last nite along with the newest SRS WOW HD sound.... anyway, put my fone on charge, left it on as I always do, woke up today and had no way up waking it up, and the charge light was still orange. I took off the back and used the reset button on the right to restart it. Unplugged it, then plugged it back in. The light immediately turned green yet when the device powered on and the screen went to black, it would NOT come off the black screen. I checked the settings for the lock screen, nothings on... I am using Energy ROM 6.5 OS 5.2.23569 build 23563.5.5.0 ... awesome ROM and yet Ive never had this prob. Had this ROM for the past 2 weeks without a hitch, installed Cookies Home Tab and the Editor progs and now this. ... any help?
EDIT: Also in the time the screen was blacked I never got a single text, MMS, fone call or email...
panthersdzynes said:
I have heard of the black screen that comes up and ppl have to soft reset to get anything to work. Never had this problem till lately. My fone was on and plugged in all nite. Never had a prob with the battery, only had this fone 3 months and now all nite and day the screen has been goin black then not waking up at all. I did install Cookies Home Tab and the CTHE Editor last nite along with the newest SRS WOW HD sound.... anyway, put my fone on charge, left it on as I always do, woke up today and had no way up waking it up, and the charge light was still orange. I took off the back and used the reset button on the right to restart it. Unplugged it, then plugged it back in. The light immediately turned green yet when the device powered on and the screen went to black, it would NOT come off the black screen. I checked the settings for the lock screen, nothings on... I am using Energy ROM 6.5 OS 5.2.23569 build 23563.5.5.0 ... awesome ROM and yet Ive never had this prob. Had this ROM for the past 2 weeks without a hitch, installed Cookies Home Tab and the Editor progs and now this. ... any help?
EDIT: Also in the time the screen was blacked I never got a single text, MMS, fone call or email...
Click to expand...
Click to collapse
OK, now it is clearer. It happened AFTER you installed software. You need to do a hard reset.
Power down the phone. Hold both left and right phone keys (red and green) while you hit the power button. The phone should reset itself back to factory condition. Unfortunately you will lose all data on the phone (the SD card data should be OK). This should fix your problem.
Yeah, its totally dead now except.... when plugged into the charger, I get an amber light. I will stop by a store and try a different battery.
By the way, AT&T Customer Service told me they will not replace my 4 month old phone because it is past the 3 month warranty.
stevedebi said:
If the indicator light never went green, the battery may be at fault. Just a thought.
Click to expand...
Click to collapse
stevedebi said:
OK, now it is clearer. It happened AFTER you installed software. You need to do a hard reset.
Power down the phone. Hold both left and right phone keys (red and green) while you hit the power button. The phone should reset itself back to factory condition. Unfortunately you will lose all data on the phone (the SD card data should be OK). This should fix your problem.
Click to expand...
Click to collapse
Already done that Steve with no luck. Next step?
If the Tilt 2 is dead, I have to replace it. Any suggestions? I was happy with this model. My big requirement is real keyboard.
if its dead its dead... if you need another just go get another I guess.... Sounds pretty crappy though. I got my phone in December and just got a warranty replacement today. They said my warranty was good till the 1 year point of when the phone was purchased or 90 days after I received the new phone (if it was close to the end of my original warranty) I assume you were out of your original warranty or bought a used phone or something. But yeah... try another battery before diving in to another phone for sure.
Possible fix
Ok, Ive kept lookin for this solution and so far, its worked. On the lock screen, especially with the new custom ROMs, the lockscreen has to be set to "classic". Something about the new Slide to unlock feature is killin the screen to black, and that makes the fone unusable... meaning when the fone goes to black, it will ONLY charge. No fone calls, no texts recieved, no emails, no nothin... calls go straight to voicemail when ppl try to call u. (when u restart the fone u may get ur emails and any MMS messages, but not texts or missed calls) If u have the Cookies Home Tab, like me, it would be labeled "Windows" lock screen that u will need. (From Home screen, click "MENU", then "Cookies Home Tab Editor", then "locksreen Settings", then under Unlock Style, click "Windows". then click "menu" at the bottom of the same screen, then click "apply settings". When u exit, Sense will refresh and ur good to go ... Ill repost in a few days to see if thats it or not.
Also I heard less talk, but some about it being an issue with the SD card. That one said to remove ur SD card, install a new ROM and reformat ur card before installing it back into the device... *(Be sure to transfer all info on card to PC before u format, formatting will erase everything from the SD card)*

Tilt 2 Will Not Boot

I have an ATT Tilt 2, approx 7 months old. I was running the EnergyROM, but I forget which one. This morning, the battery died, I plugged it in too charge on my laptop. I got a dialog box that said the charging power was insufficient to run the device, and it turned itself off. I let it be for a while (hour or so) then tried to reboot. It would not respond to the power button, so I hit the red reset button with my stylus. It booted, but not successfully. The phone got caught in what I can only describe as a loop. It would start the boot animation, then fail. It would stay turned off for a few minutes, then spontaneously try to boot again.
I held down the reset button again........nothing. Power button.......nothing. So then I tried to wipe it, using my micro SD card. I was able to get the phone into bootloader mode, and told it to apply the update by pressing the volume key. However, it still loops, except now it goes into the bootloader, except there is an error message in the bootloader screen, buried under the text. FWIW I am using the Olinex HardSPL.
Any help is GREATLY appreciated
EDIT: This only happens when it is plugged in. When it is on battery, it is completely unresponsive. No power button, no reset button, nothing. All i get is the amber charge light
tubagod101 said:
I have an ATT Tilt 2, approx 7 months old. I was running the EnergyROM, but I forget which one. This morning, the battery died, I plugged it in too charge on my laptop. I got a dialog box that said the charging power was insufficient to run the device, and it turned itself off. I let it be for a while (hour or so) then tried to reboot. It would not respond to the power button, so I hit the red reset button with my stylus. It booted, but not successfully. The phone got caught in what I can only describe as a loop. It would start the boot animation, then fail. It would stay turned off for a few minutes, then spontaneously try to boot again.
I held down the reset button again........nothing. Power button.......nothing. So then I tried to wipe it, using my micro SD card. I was able to get the phone into bootloader mode, and told it to apply the update by pressing the volume key. However, it still loops, except now it goes into the bootloader, except there is an error message in the bootloader screen, buried under the text. FWIW I am using the Olinex HardSPL.
Any help is GREATLY appreciated
EDIT: This only happens when it is plugged in. When it is on battery, it is completely unresponsive. No power button, no reset button, nothing. All i get is the amber charge light
Click to expand...
Click to collapse
That means the phone is NOT charging the battery. Did you try using another USB cable? If so, did you try another battery? If you tried that too and it still doesn't work, that may mean that the charging circuit is dead and you will have to either get that one repaired or get a new phone
tubagod101 said:
I have an ATT Tilt 2, approx 7 months old. I was running the EnergyROM, but I forget which one. This morning, the battery died, I plugged it in too charge on my laptop. I got a dialog box that said the charging power was insufficient to run the device, and it turned itself off. I let it be for a while (hour or so) then tried to reboot. It would not respond to the power button, so I hit the red reset button with my stylus. It booted, but not successfully. The phone got caught in what I can only describe as a loop. It would start the boot animation, then fail. It would stay turned off for a few minutes, then spontaneously try to boot again.
I held down the reset button again........nothing. Power button.......nothing. So then I tried to wipe it, using my micro SD card. I was able to get the phone into bootloader mode, and told it to apply the update by pressing the volume key. However, it still loops, except now it goes into the bootloader, except there is an error message in the bootloader screen, buried under the text. FWIW I am using the Olinex HardSPL.
Any help is GREATLY appreciated
EDIT: This only happens when it is plugged in. When it is on battery, it is completely unresponsive. No power button, no reset button, nothing. All i get is the amber charge light
Click to expand...
Click to collapse
Try charging it from the wall plug. Your laptop port is not putting out enough power. Let it charge until the green light comes on.
rr5678 said:
That means the phone is NOT charging the battery. Did you try using another USB cable? If so, did you try another battery? If you tried that too and it still doesn't work, that may mean that the charging circuit is dead and you will have to either get that one repaired or get a new phone
Click to expand...
Click to collapse
Can the charging circuit be replaced? Can i repair it my self (buy parts on ebay)? Would you happen to know much will it cost to repair it from AT&T?
star2gates said:
Can the charging circuit be replaced? Can i repair it my self (buy parts on ebay)? Would you happen to know much will it cost to repair it from AT&T?
Click to expand...
Click to collapse
So I take it it never worked when on the wall charger?

[Q] Need Help in Laymen's Terms...Tilt 2 Stuck on Red, Green, Blue, and White Screen.

I have a HTC Tilt 2... I have been having a ton of problems with this phone but when it really freaks out, I usually take the battery out, let it sit a few days and then it starts working again. My phone started doing some funny things today so I restarted it as usual, it freezes and I remove the battery. When I turned it back on I got a red, green, blue and white screen with text:
RHOD300 32M MI-BC
SPL-0.87.0000
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
498, 526 792,855
795,211 214,211
223,845 Calibrated
This has never happened before.
This RGB&W screen used to say serial when it first happend a few hours ago but then I installed ActiveSync and plugged it into PC, now says USB.
ActiveSync won't recognize my device, it does appear in My Computer.
I tried following directions in another forum to turn the device off then hold the pickup/hangup/power button at the same time...a different screen appeared than the forum directed, a gray screen with "Trigger Ramdump Mode"...then I couldn't do anything.
I can restart it back into the tri-color screen...
I need help in laymen's terms. I've never tried to change anything about the phone's operating system, I've never done an update or anything, I do not have the Tilt2 CD.
Right now I have my SIM card and my SanDisk card removed, I was afraid it could get erased when I tried the pickup/hangup/power button trick.
PLEASE SOMEONE HELP!!!!!!!!!
This screen is called the bootloader. Its used by technicians (or more advanced users) to load the OS or "ROM" onto the phone. It may be stuck in bootloader because some of the OS files are damaged or missing, and the OS is not booting up. Or possibly even a hardware failure.
Pulling the battery may/may not be the culprit. I've read someone on here mention that pulling the battery can corrupt files on the phone. If the phone is lagging, frozen, then pulling the battery is not the correct way to restart the phone. The correct method of restarting the phone by soft reset is done by sticking the stylus into the small red hole/button on the side of the phone, while the batter cover is off:
http://www.hardreset.eu/htc_touch_pro_2_rhodium_hard_reset_soft_reset_en.html
Pulling the battery is only a method of last resort, as the soft reset button will work in almost all cases.
Hard reset by holding TALK, END and POWER is probably not going to work. It requires the OS to be working, and you are not even getting to the point that the OS is booting.
Its supposed to say "USB" when the phone is connected to your PC via the USB cable. If I remember properly, it will say "Serial" in bootloader for a second when you plug the phone to USB, and switch to saying "USB" after that. USB is a form of serial connection, after all (USB = Universal Serial Bus). As long as it says "USB", you are in somewhat good shape, since it SHOULD allow you to try the following.
Try downloading the latest ROM from HTC. This is actually a newer version than the ROM that was originally on your phone, but still "official" ATT software. And by most accounts, better than the old ROM. Since its official software, installing this will not endanger any warranty you may still have on the phone.
Its the first file on the following page ("ROM Update"):
http://www.htc.com/us/support/tilt-2-att/downloads/
With your phone connected to your PC by USB, run the .exe ROM update file and follow the instructions that come up on your PC screen. It should work. Try it and let us know.
Bear in mind, you will lose any personal data you have on the phone (contacts, texts, emails, etc). But you've probably already lost those.
Its possible there is some other way out of it, I certainly don't know all the tricks. But in searching around this site, being stuck in bootloader seems to require flashing a new ROM to get out of it. And it seems that you are prepared to lose your personal data, based on the fact that you were already trying to hard reset (the TALK, END, and POWER button process) which also dumps all your data. And flashing the official ROM is really pretty easy to accomplish. Just a pain that you have to re-setup the phone again, since it will basically be returned to factory condition (but in this case, a slightly newer version of the OS).
The SAME thing happened to My HTC Tilt 2 an Hour ago (1/13/2010 4:46pm)
The same exact thing occurred to my HTC Tilt 2 today. It is stuck on the red green, blue and white screen with the same yellow 'config' type message . The white bottom strip has the black letters "serial" typed in.
My problem also, is that the phone stays "on" until i pull the battery out. The moment i place the battery back in the phone, the keys stay lit up instantly and the screen is black. When pressing the power button, then i get the same red, green, blue and white screen.
Ive tried holding the talk/end/power buttons all at the same time, it doesnt make a difference. So i cant get to the step where you press the "volume up" key so to initiate the master reset.
Ihad no idea the HTC Tilt2 would just fry like this. I had no additional apps that were unusual to the norm, i even had more free space than used on the set. its not like the phone was over loaded.
Hmmmmm.... help!!!
Re-read above about "soft-reset" and you might want to try reflash your phone.
Sent from my MSM using Tapatalk
RicoATT said:
The same exact thing occurred to my HTC Tilt 2 today. It is stuck on the red green, blue and white screen with the same yellow 'config' type message . The white bottom strip has the black letters "serial" typed in.
My problem also, is that the phone stays "on" until i pull the battery out. The moment i place the battery back in the phone, the keys stay lit up instantly and the screen is black. When pressing the power button, then i get the same red, green, blue and white screen.
Ive tried holding the talk/end/power buttons all at the same time, it doesnt make a difference. So i cant get to the step where you press the "volume up" key so to initiate the master reset.
Ihad no idea the HTC Tilt2 would just fry like this. I had no additional apps that were unusual to the norm, i even had more free space than used on the set. its not like the phone was over loaded.
Hmmmmm.... help!!!
Click to expand...
Click to collapse
Read my post above. Your OS is missing or damaged, and you need to reflash (re-install) it.
Master reset re-loads the OS from the ROM area of your memory. The ROM is damaged, so their is nothing to reload. That's why its stuck in bootloader (tri-color screen).
redpoint73 said:
Read my post above. Your OS is missing or damaged, and you need to reflash (re-install) it.
Master reset re-loads the OS from the ROM area of your memory. The ROM is damaged, so their is nothing to reload. That's why its stuck in bootloader (tri-color screen).
Click to expand...
Click to collapse
_______________________________________________________
Today, i stuck the battery in the phone (Tilt2) pressed the hard reset keys. THIS time it allowed the volume-UP key to finally kick in the reset to default cycle. I got the phone working again and have restored my last backup So, I havent lost anything.
The only problem now i am noticing is the light on the keyboard never goes off. Even when I power the phone down, "the keyboard stays lit".. I am having to remove the battery just to keep it from draining when the phone is not in use.hmmm. is there a regEdit key I can modify that may turn off the keys? id rather have no light at all over no battery juice. If i can edit the key to turn off the backlight on the keyboard permanantly , this will be a temp fix for me until i get a new phone.
as anyone ever experienced this?
RicoATT said:
_______________________________________________________
Today, i stuck the battery in the phone (Tilt2) pressed the hard reset keys. THIS time it allowed the volume-UP key to finally kick in the reset to default cycle. I got the phone working again and have restored my last backup So, I havent lost anything.
The only problem now i am noticing is the light on the keyboard never goes off. Even when I power the phone down, "the keyboard stays lit".. I am having to remove the battery just to keep it from draining when the phone is not in use.hmmm. is there a regEdit key I can modify that may turn off the keys? id rather have no light at all over no battery juice. If i can edit the key to turn off the backlight on the keyboard permanantly , this will be a temp fix for me until i get a new phone.
as anyone ever experienced this?
Click to expand...
Click to collapse
_______________________________________________________
Well, today 1/18/2011: the above issue seem to have vanished altogether. Very good. I did nothing but what i was resolved to do until I buy a new phone (take the battery out so to completely power down the phone and lights).
Today, my ole third hand decided to work like normal! Yay!. All of a sudden it rebooted, and now the keyboard backlight turns off when the keypad is closed and you can see it light up when extended. and most importantly: the back lighty for the keypad goes "off" when the phone is powerd down. go figure this one.
I am glad its working like normal now, but i know its time to get a new phone. These are just symptoms of the "big-crash" soon to come. I am backing up every day.
For now, very very glad my phone is back to "normal"

Galaxy tab S T705 not turning on without charger

hi guys,
sorry if i had to ask this i think i'm out of options that i'm aware of.
i have a tab s t705 which has been on stock firmware for the longest time(5.02, country PH) and a week ago it just died.
the tablet charges but does not turn on. i can get to odin and recovery modes but it does not boot to system. also it does not turn on when i unplug the charger.
what i've done so far:
. pressed the power button for more than 30seconds, unplugged - nothing
. pressed the power, home, and -vol buttons for about the same time, unplugged - nothing
. pressed the power button for the same amount of time, plugged - only charging icon with batt level, nothing else
. pressed the power, home, nd -vol buttons for a few seconds while plugged, gets into pdin mode but restarting it just goes back to charging icon
. pressed power, home, and +vol for a few seconds while plugged, gets into recovery mode and after trying factory wipe and wipe cache, still goes back to charging icon when rebooted
. followed a guide to remove the back cover and disconnected battery for more than five minutes and did the same steps - same results
. tried plugging in to computer where it was installed before - not detected, not even odin(3.05 - 3.11 versions) does not detect it
this tablet is absolutely out of warranty already and i sort of like this tablet. any chance i can still revive this, or were there some steps that i have missed?
seriously, thanks in advance for any help
If you have an DMM check the voltage of the battery it should be 4.35v fully charged battery, If the battery is faulty maybe that is what is stopping the tablet fully booting, maybe somebody else knows.
John.
unfortunately i dot have acces to such tool but i really am hoping that this could be just a dead battery.
i'll see if replacing the batt would fix this and reply back for the results. thanks!

Categories

Resources