Related
Hi,
i have problem with my PDA (Qtek 1010), once i reset ,it is not working, it shows the message "This ROM was cooked in the XDA-developere.com ROM kitchen cooked to order.to suit your demanding taste" & stopped on this screen only,i tried lot of time, but still the same prblm . so plz, can u assist , how to over come frm this prblm.
thnking u
What have you actually tried so far? Have you reflashed it with another ROM/the original ROM?
HI plz do need full
Complete scene what happen:
I m trying to connect using IR to laptop, that time it
hangup, so I made soft reset. After I made reset It will not start,
thn I tried lot of time soft and hard reset, It will showing only
initial screen " This ROM was cooked in the xda-developers.com ROM
Kitchen cooked....." and stopped here only. It is not loading the
operating system. So please do need full. I ill grateful for u.
Now also i tried These below Step ,
How to Flash your Device using bootloader and SD-Card....
1. Download XDATools
ftp://xda:[email protected]/Wallaby/Tools/XDATools.zip
2. Extract them at any place and run osimagetool
3. Select your Rom Image from the Source drop down menu.
4. Select your SD card (disk drive) from Destination the drop down menu.
5. Select Copy to start writing process and the tool should start writing to
the card.
6. When XDATools has finished writing the image (no Infomessage) put the
SD-card into your device
7. If there comes a message to format the SD-card select No
8.
Hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
9. Press action to download and it will start the download/restore from the
SD card.
10. Follow the on screen instructions once its "Completed" which will consist
of a " Hard Reset"
You can get an original ROM here:
ftp://xda:[email protected]/Wallaby/ROM/
Or cook your own at http://lumpistefan.dyndns.org
Since the ROMs are a exe fiel, you have to extract the exe file using winzip.
You get a folder english containig the ROM NK.nbf with about 32 MB....
You can use all ROM's excpet the WM2003SE
But now i m getting the error " After complete, I made hard reset, its on first screen as "Test Only Not for Sale, Microsoft Windows powered" message with version details and stopped here only. It is not moving ahead. So plz can u instruct further wht to do
Thanks & Regards
kAreem khan
System Engg.
My P535, 71A version. upgrade WM6 HK version from 4.3.25 HK00.
I used a 256MB miniSD with quick formatted( it's the main reason). extract the upgrade file on it. and start the upgrade procedure.
1st step: insert the miniSD into slot. autorun started and asked to confirm. sure. confirm it.
2nd step: system starting upgrade the bootloader, read, verify, and update ok. it ask to reset with power button pressed. do as requested.
Like attachment 111.jpg
3rd step: the bootloader entered a new uploader version with "force mode" displayed. and loading the main upgrade file ASUSP535.CAP. but checksum failed. it it asked to reset with power button pressed again. do as requested.
Like attachment 222.jpg , I failed at checksum because the miniSD only quickformatted
then the nightmare came. I can't see the blue asus screen. and nothing happen when I press reset. the only valid operations are Power+Camera+Recorder + reset to the SD download mode, and Power+Camera + reset to the USB sync mode. in the SD download mode. system not recognize the *.cap file. it request a NB0 file.
What should I do?
1. Enter the Force mode again with a good formatted miniSD is the best way. but how?
2. Use the USB sync mode upgrade the file, it maybe works. but I can't find the usbloader. in my memory. there is one in the lifeforce cooked ROM pack. but it removed when I visit lifeforce's site today. anyone who download the rom pack before please give me the file. I need a try.
-------------------------updated on 9th Jul 2007---------------------------------------
My P535 has been recovered.
just use a modfied 4.3.25 HK00 NB0 file at the SD download mode, it can reverse to WM5, then repair the extend firm. don't reset, direct run 4.3.25 offical update. switch to another sd card with WM6 upgrade ASUSP535.CAP when it reboot to the sd download update screen. and all will go on.
find an old rom on asus ftp or site.
Rename the rom to galaxyII.nb0
Copy it to the card.
Boot your phone with the card in SD download mode.
The upgrade will start.
Good luck.
For me after the autorun, i pressed ok to restart but the phone still block at the blue screen. I try to reset in sd loader with the new rom in sd, with the galaxy name, and the rom is to big for the phone...
ilan_75 said:
find an old rom on asus ftp or site.
Rename the rom to galaxyII.nb0
Copy it to the card.
Boot your phone with the card in SD download mode.
The upgrade will start.
Good luck.
For me after the autorun, i pressed ok to restart but the phone still block at the blue screen. I try to reset in sd loader with the new rom in sd, with the galaxy name, and the rom is to big for the phone...
Click to expand...
Click to collapse
I had tried as you said. put 4.3.25 HK CAP file on the minSD, and rename it with NB0, but it not work, it return red words with" Wrong Language Version, Update fail!" the system is the HK before update WM6
You may try try here...
http://www.asuspda.net/thread-17850-1-1.html
but not sure does it 100% work...
Good Luck!
Hello,
I've attached the requested tool - and... good luck
A_C said:
You may try try here...
http://www.asuspda.net/thread-17850-1-1.html
but not sure does it 100% work...
Good Luck!
Click to expand...
Click to collapse
thanks, but that's not what I need, because I can't enter the OS already...
windirt said:
thanks, but that's not what I need, because I can't enter the OS already...
Click to expand...
Click to collapse
It is picked from that archive...
lukacs.attila said:
Hello,
I've attached the requested tool - and... good luck
Click to expand...
Click to collapse
sigh... I tried with usb sync, the 79MB cap file can't transfer completely. it just transfered 55MB and stopped.
windirt said:
sigh... I tried with usb sync, the 79MB cap file can't transfer completely. it just transfered 55MB and stopped.
Click to expand...
Click to collapse
I have no idea, but maybe it is because you already upgraded the bootloader?
lukacs.attila said:
I have no idea, but maybe it is because you already upgraded the bootloader?
Click to expand...
Click to collapse
Yes. the first upgrade step is completed, the bootloader version is changed to 2007/04/16.
when I press Power+Rec+UP and reset, it got a Force mode USB Sync. not like the ordinary USB Sync enabled by Power+Rec and reset.
is there a way to get a Force mode with SD Download? so I can use the 79MB CAP if it accessable.
windirt said:
Yes. the first upgrade step is completed, the bootloader version is changed to 2007/04/16.
when I press Power+Rec+UP and reset, it got a Force mode USB Sync. not like the ordinary USB Sync enabled by Power+Rec and reset.
is there a way to get a Force mode with SD Download? so I can use the 79MB CAP if it accessable.
Click to expand...
Click to collapse
Correct me if I am wrong, but there's something written @ asus support site, where you can download the new firmware (it's a step by step how-to). Unfortunately, the support site is down at the moment.
Please follow the below procedures to upgrade:
1.Please format your Mini-SD first.
2.Unzip the file and copy it to Mini-SD card's root folder
(Under Mini-SD's root folder, there should only be folder 2577, AsusP535.cap, and GalaxyII.cap;
In folder 2577, there should only be Autorun.exe).
3.Insert the Mini-SD with upgrade firmware into P535's expansion slot and wait for firmware to setup automatically.
If the firmware didn't execute automatically, please execute Autorun.exe in Storage Card\2577\.
4.Click "System" => "Update ROM"
5.System will enter update mode, here the first part of upgrade will start.
Warningo not interrupt the upgrade process. Please execute the rest of the steps until completing step 8 in order
for the unit to execute normally. After the upgrade is complete, a message in red will be displayed.
Please press and hold power button and reset at the same time to start second part of upgrade.
6.After reboot, it will automatically enter update mode. This upgrade takes about 3 mins, please wait patiently.
Please do not interrupt the upgrade process. After upgrade is done, system will reboot automatically.
7.After reboot, it will install extended ROM automatically. After upgrade is done, system will reboot automatically.
8.Please Confirm version in "Start"=>"Setting"=>"System"=>"System Information"=>"Version".
lukacs.attila said:
Please follow the below procedures to upgrade:
1.Please format your Mini-SD first.
2.Unzip the file and copy it to Mini-SD card's root folder
(Under Mini-SD's root folder, there should only be folder 2577, AsusP535.cap, and GalaxyII.cap;
In folder 2577, there should only be Autorun.exe).
3.Insert the Mini-SD with upgrade firmware into P535's expansion slot and wait for firmware to setup automatically.
If the firmware didn't execute automatically, please execute Autorun.exe in Storage Card\2577\.
4.Click "System" => "Update ROM"
5.System will enter update mode, here the first part of upgrade will start.
Warningo not interrupt the upgrade process. Please execute the rest of the steps until completing step 8 in order
for the unit to execute normally. After the upgrade is complete, a message in red will be displayed.
Please press and hold power button and reset at the same time to start second part of upgrade.
6.After reboot, it will automatically enter update mode. This upgrade takes about 3 mins, please wait patiently.
Please do not interrupt the upgrade process. After upgrade is done, system will reboot automatically.
7.After reboot, it will install extended ROM automatically. After upgrade is done, system will reboot automatically.
8.Please Confirm version in "Start"=>"Setting"=>"System"=>"System Information"=>"Version".
Click to expand...
Click to collapse
Yes, it stopped in step6 as you posted, checksum error.
Upgrade WM6 critical problem
I was trying to upgrade my ASUS P535 rom from V4.3.15 WWWEL_RU to firmware V4.7.12 WWE_TH00
I unzipped the P535_V4712_WWE_TH00_EXT_V120 and copied the files produced to the miniSD card except from file AsusP535.cap
I renamed file GALAXYII.cap to GALAXY.cap and copied it again to miniSD card. Also I copied file ASUS.UnlockLangID to folder 2577 and replaced autorun. (P535 ROM Tools.zip from http://forum.xda-developers.com/showthread.php?t=295778&page=3)
So in miniSD card there are the following files: 2577 folder with autorun and unlocklangid.exe, and in the root, GalaxyII.cap and GALAXY.cap but NOT AsusP535.cap
So I run the update and after the reset I get message ASUSP35.CAP NOT FOUND.
At that point I realise my stupidity (not copying AsusP535.cap to miniSD) so I take the card out, put it in my laptop and copy the AsusP535.cap to mini SD.
I reset the device and stick the card in but I still get the same message ASUSP35.CAP NOT FOUND.
Every time I turn on my device it tries to upgrade rom and I get the mesage. Can someone help please or have I damaged the device beyond repair?
2 mins ago I upgraded my taiwanese p535 to the thailand wm6 rom.
I had already installed a 4.3.15 wwe version, so I figured I could just install the 4.7.12 wwe TH rom without using the "hacked autoexec".
That didn't work, and I was stuck with the blue asus screen.
So I pushed up (on the d-pad) + reset, then "green phone button" (answer button) when it asked if I wanted to.
then reset the phone as soon as it said "performing upgrade" or something like that (when it started installing stuff after windows was booted).
After reboot, I was back at my old 4.3.15 rom.
Then I decided to retry it, following the instructions here:
http://forum.xda-developers.com/showpost.php?p=1352033&postcount=77
(the link to the p525 tools is incorrect. It should be: http://rapidshare.com/files/4612627/ASUS_P525_v3.32.WWE.customized.build.06.zip.html
Edit: The link to the thai wwe rom is incorrect too, it should be: http://dlsvr01.asus.com/pub/ASUS/IA/P535/P535_V4712_WWE_TH00_EXT_V120.rar)
When I followed these instructions the upgrade worked perfectly. I now have 4.7.12 wwe_au00 installed
I can't give any guarantees, And it may be that I was just lucky, but I suggest you try to remove the miniSD, then push up+reset, press "answer button" when it wants you to confirm, and then, after it reboots, press the reset button as soon as it starts the "upgrade". Then (I hope) it will revert back to your previously installed OS.
After that, upgrade to wm6 following the procedure in the link I pasted above.
extract nb0 from cap for asus p535:
wm5:
xda2nbftool.exe -x galaxyII.cap galaxy2.nba 0xA87BC0d5
wm6:
xda2nbftool.exe -x asusp535.cap asusp535.nba 0xa87ba0d5
.nba from .nb0 seems differs for 4 bytes
.nba - first 4 bytes = .nb0
(check it /in device upgrade may be significant - don't knew (i'm use other device)/ )
.nba, .nb0 - standard files as for oher devices - can make modified firmware images as for other ...
I can't give any guarantees, And it may be that I was just lucky, but I suggest you try to remove the miniSD, then push up+reset, press "answer button" when it wants you to confirm, and then, after it reboots, press the reset button as soon as it starts the "upgrade". Then (I hope) it will revert back to your previously installed OS.
After that, upgrade to wm6 following the procedure in the link I pasted above.[/QUOTE]
Unfortunately, when I press up+reset I dont get the option to confirm, it just goes immediately to the same message ASUSP35.CAP NOT FOUND
DaLiV said:
extract nb0 from cap for asus p535:
wm5:
xda2nbftool.exe -x galaxyII.cap galaxy2.nba 0xA87BC0d5
wm6:
xda2nbftool.exe -x asusp535.cap asusp535.nba 0xa87ba0d5
.nba from .nb0 seems differs for 4 bytes
.nba - first 4 bytes = .nb0
(check it /in device upgrade may be significant - don't knew (i'm use other device)/ )
.nba, .nb0 - standard files as for oher devices - can make modified firmware images as for other ...
Click to expand...
Click to collapse
I am sorry but I dont understand the solution you are suggesting
Could you please explain?
ntiouk said:
Unfortunately, when I press up+reset I dont get the option to confirm, it just goes immediately to the same message ASUSP35.CAP NOT FOUND
Click to expand...
Click to collapse
Hold the up button, then press reset while still holding the up button.
are you sure it says "ASUSP35.CAP"?
It doesn't say "ASUSP535.CAP"?
.nb0 - it's another way t program device
press photo + reset - that asks file - resulted .nb0 file for wm5 or wm6 name as device wants - write that to sd (not sdhc) card formatted as fat16 - and insert it to device.
When i download the USPL_2.28.0000_with_IPL_2.27 it comes with a folder named RUU.
The folder of the ROM (Onyx Ultimate 4.0) i choosen to flash comes too with a RUU folder.
Flashing SPL proccess:
************************************************** ***********
Please make sure Activesync is enabled (green icon in systray)
and hit ENTER to start...
STEP 1/3......50%......75%....100%
The next step will load a patched bootloader (SPL) on your device
it will make your device temporary SuperCID (seclevel=0), and will
avoid modelID and signature checking when flashing NBH files.
Hit ENTER to continue...
STEP 2/3.....15%.....25%...50%...75%.....100%
Phone screen should now be blank and the activesync icon gray
if not, the loading procedure has failed and you'll have to repeat again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash patched SPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
STEP 3/3 - Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate
************************************************** ***********
(c)2007 pof - XDA Developers
Hit ENTER to quit.
---------------------------------------------------------------------------
My question about this proccess is in step 3, when is saying "Launching RUU".
What RUU is this? Do i need to complete this RUU and then execute the RUU for Onyx? Is there 2 RUU happening to a successful flashing?
I saw in a site this tutorial:
1) Extract the USPL files to a folder, keep this window open.
2) Connect the Orbit to your PC (or laptop).
3) Once you have the Green ActiveSync icon, run start_uspl.exe, in your open folder from 1).
4) The start_uspl program opens in it's own DOS window. When the progress indicator reaches 100, 2 things will happen.
- ActiveSync will disconnect (you should also hear the 'USB Disconnect/reconnect' sound on your desktop), and
- The orbit screen will go blank (mine goes black, some go white)
Don't let this put you off, and continue undeterred, you're nearly there. Also, don't be tempted to disconnect anything, or reset your device.
5) Return to your extracted files window from 1), run ROMUpdateUtility.exe.
6) Follow the instructions in the three screens to start the update, which should take about a minute (not 10 as the screen suggests).
7) Once you get the "Congratulations" screen, the USPL phase is complete
--------------------------------------------------------------------------
What i can see from here is that i will complete the RUU from the SPL and then execute again another RUU thats comes in the Onyx folder. Right?
Sorry for the lammes questions
(I've already posted this in another area of the forum, didn't know what's the best one to post)
After a lot of reading, I collect the following, just for my own aid. I hope it will be proved useful to others.
I' ve just gathered all this information. All thanks goes to all those nice guys that spend time & put effort to find out all these procedures.
I'm just a bug.
(A few posts after this one, in the same thread, you can find the following guides:
How to Install NAND Android on HTC HD2 WITHOUT ClockWorkMod Recovery
&
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE (without clockwork mod)
&
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE (with clockwork mod)
At the end of this post you can find the neccessary files to download.
So here it is:
How to Install NAND Android on HTC HD2 with ClockWorkMod Recovery
(updated 25 May 2011)
Prerequisites
HSPL3 ~ SPL-2.08.HSPL or HSPL4 (Better use HSPL3. HSPL4 still has issues or errors on some devices, so use it at your own risk).
Radio that support 576 RAM (ex. radio ROM 2.15)
DFT MAGLDR Bootloader
ClockworkMod Recovery
It's advisable to copy the NAND Android ROM zip file to the root of your SD card, before start, because some people face problems to do this after doing the first steps of the process. If you don't do it then you can do it later using a card reader or doing this:
In MAGLDR choose option: #4 USB Mass Stg
or
In CWM choose option: mounts and storage option
Make sure that you have all the prerequisites installed.
STEPS:
A1: Install HSPL3
or
A2: Install HSPL4 (HSPL4 still has issues or errors on some devices, so use it at your own risk).
B: Install radio ROM 2.15
C: Install MAGLDR on HTC HD2
D: Install ClockworkMod Recovery (2 methods, choose the one you like)
E: Install NAND Android on HTC HD2 with ClockWorkMod Recovery
A1: Install HSPL3
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
(To check your SPL version, hold the Volume Down button and do a reset)
You should have this SPL version unless you are using the latest 3.14 ROM with SPL 3.03.0000. No worry, just downgrade your Windows Mobile ROM from v3.14 to v1.66 will do. Download HTC HD2 v1.66 ROM. Then downgrade your phone from SPL 3.03.0000 to SPL 1.42.000.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL3_PKG.zip with 7-Zip.
10. Copy HSPL3_PKG.exe to desktop.
11. Execute HSPL3_PKG.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select ’2.08.HSPL’ to install.
16. After installation, you should see ‘We hacked it!’ on your phone.
17. Click on ‘Yes’ and your phone should be rebooted and load into Windows Mobile.
18. Disconnect USB cable from phone.
19. To verify, power off your phone.
20. Press volume down button (don’t let go) and power on your phone.
21. It will load into bootloader.
22. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
23. That’s all.
OR
A2: Install HSPL4 (HSPL4 still has issues or errors on some devices, so use it at your own risk).
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
o SPL 3.03.0000 (for those using latest official HTC HD2 ROM v3.14)
(To check your SPL version, hold the Volume Down button and do a reset)
HSPL4 includes SPL-2.08.0000, SPL-2.08.HSPL, SPL-3.03.0000 and SPL-3.03.HSPL. The 3.03 SPL supports LEO1024.
You still need to use SPL-2.08.HSPL to use NAND Android and Windows Phone 7 and MAGLDR.
Make sure that you select the correct HSPL for your ROM installation.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL4.zip with 7-Zip.
10. Copy HSPL4.exe to desktop.
11. Execute HSP4.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select 2.08HSPL or 3.03HSPL. (This is to prevent people with 1024LEO's installing an incompatable version and bricking their device).
16. Click next
17. When its finished the phone should be rebooted and load into Windows Mobile.
18. Click ok to terminate program
19. Disconnect USB cable from phone.
20. To verify, power off your phone.
21. Press volume down button (don’t let go) and power on your phone.
22. It will load into bootloader.
23. You should get ‘Red, Green, Blue and White’ screen with SPL 2.08 or 3.03.
24. That’s all.
B: Install Custom Radio ROM
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
In order to flash custom radio ROM, you need to have HSPL3 installed on your HTC HD2. By the way, I used Radio Leo 2.15.50.14 on my guide. You can use it or any other HTC HD2 Radio ROM version.
HTC HD2 has 576 MB physical RAM but was reduced by software to 512 MB only. And custom Windows Mobile ROM + radio 2.07 or above can unlock it to be 576 MB again. Certain custom Windows Mobile ROM need higher radio version than your phone. And NAND Android requires it too. So you need to install custom radio ROM (if you don’t have the correct radio version).
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. I have R 2.06.51.07 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open Radio Leo 2.15.50.14.rar with 7-Zip.
11. Copy CustomRUU.exe and RUU_signed.nbh to desktop.
12. Execute CustomRUU.
13. Click ‘Yes’ if User Access Control prompt up.
14. Follow onscreen instructions to install.
15. Bootloader will be loaded with USB status during starting of installation. (~10 minutes)
16. Phone will be rebooted after installation finished.
17. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
18. Disconnect USB cable from phone.
19. That’s all.
C: Install MAGLDR
In order to install NAND Android on HTC HD2, you must install DFT MAGLDR Bootloader first. And the good news ~ both LEO512 and LEO1024 are supported. This means US T-Mobile HD2, Europe, Asia and the rest of the world’s HTC HD2 are supported.
Note – by installing MAGLDR, you cannot boot into Windows Mobile anymore. So everything on your phone is gone…
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
No worry, Android on NAND is working. That’s the reason we install DFT MAGLDR Bootloader on our HTC HD2, right? And we will be able to load the latest Windows Phone version (if we are crazy...) when the ROM comes out. Okay, let’s get started. If you don’t have HSPL3, please install it first. And aslo install radio ROM 2.15.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open DFT_LEO_MAGLDR113.rar with 7-Zip.
11. Copy MAGLDR113 folder to desktop.
12. Enter MAGLDR113 folder.
13. Execute ROMUpdateUtility.
14. Click ‘Yes’ if User Access Control prompt up.
15. Follow onscreen instructions to install.
16. Bootloader will be loaded with USB status during starting of installation.
17. Phone will be rebooted after installation finished.
18. DFT MAGLDR Bootloader will be loaded then.
19. Disconnect USB cable from phone.
20. That’s all.
D: How to Install ClockworkMod Recovery on HTC HD2
Prerequisites
HSPL3 ~ SPL-2.08.HSPL
Radio that support 576 RAM
DFT MAGLDR Bootloader
Please make sure that you have all the prerequisites installed.
If you don’t have HSPL3, please install it.
Also install radio ROM 2.1.
Finally, install DFT MAGLDR Bootloader.
There are two methods. They are both working. Choose the one you like.
Method 1
Step by Step Guide
1. Power on your phone and don’t let go power button.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 4. USB MassStg.
4. Then press call button to enter USB Mass Storage mode.
5. Connect USB cable from PC to phone.
6. At PC, open Removable Disk (SD card storage).
7. Create a temp folder.
8. Open ClockworkMod-Recovery V.1.2 with 7-Zip.
9. Copy everything to temp folder.
10. Enter temp folder.
11. Enter copy_to_sd_root folder.
12. Copy initrd.gz and zImage files to SD card root level.
13. Then disconnect USB cable from phone.
14. Press power button to go back.
15. Use volume down button to go to 11. Reset.
16. Then press call button.
17. Press power button and don’t let go.
18. DFT MAGLDR Bootloader will be loaded.
19. Use volume down button to go down to 5. USB Flasher.
20. Then press call button to load Android Flasher mode.
21. Connect USB cable from PC to phone.
22. At PC, right click on DAF and select ‘Run as administrator’.
23. Click ‘Yes’ if User Access Control prompt up.
24. Follow onscreen instructions to install.
25. Phone will be rebooted after installation finished.
26. DFT MAGLDR Bootloader will be loaded then.
27. Disconnect USB cable from phone.
28. Press call button to load 2. Boot AD SD.
29. ClockworkMod Recovery will be loaded then.
30. That’s all.
Alternatively, there exist a faster method, from MAGLDR NAND Boot. It goes like this:
Method 2
Step by Step Guide
1. Download recovery with partition size for the type of rom you plan on using (150, 250 or 400) (to choose, see the guide at the bottom of this post).
2. Extract downloaded file
3. Go into MAGLDR and choose 5. USB Flasher.
3. On PC run DAF.exe and follow instructions
4. After installation completed and phone reboots, hold power key and select 8. AD Recovery
5. The phone will load into Recovery
6. That’s all.
E: Install NAND Android on HTC HD2 with ClockWorkMod Recovery
Install NAND Android on HTC HD2 with ClockworkMod Recovery is the 2nd method to have NAND Android on HTC HD2. And this can be done by using SD card only without PC. Just download the zip ROM to your SD card and you are ready to go. In addition, you can backup and restore ROM using Nandroid. Or you can try the 1st method through DFT MAGLDR Bootloader which requires PC with USB connection.
Prerequisites
HSPL3 ~ SPL-2.08.HSPL
Radio that support 576 RAM
DFT MAGLDR Bootloader
ClockworkMod Recovery
Having NAND Android on HTC HD2 is not a simple task like ABC. But it is not mission impossible too. Just follow these guides to get all the prerequisites installed. Please install HSPL3. Install Custom Radio ROM 2.15. Then, install DFT MAGLDR Bootloader. Finally, install ClockworkMod Recovery. Wow… Lot of steps but worth it. Trust me…
Step by Step Guide
1. Power on your phone and don’t let go power button.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 4. USB MassStg.
4. Then press call button to enter USB Mass Storage mode.
5. Connect USB cable from PC to phone.
6. At PC, open Removable Disk (SD card storage).
7. Open your favorite ROM (ex. JawsMIUIrec1.0.7z) with 7-Zip.
8. Copy .data folder and ex. JawsNandRec1.1.zip to SD card root level.
9. There should be config and data files in .data folder.
10. Then disconnect USB cable from phone.
11. Press power button to go back.
12. Use volume up button to go up to 12. PowerDown.
13. Then press call button.
14. Power on phone and don’t let go power button.
15. DFT MAGLDR Bootloader will be loaded.
16. Press call button to load 2. Boot AD SD.
17. ClockworkMod Recovery will be loaded then.
18. Use volume down button to go down to ‘install zip from sdcard’.
19. Then press call button.
20. Use volume down button to go down to ‘choose zip from sdcard’.
21. Then press call button.
22. You should see ex. JawsNandRec1.1.zip.
23. Then press call button to select it.
24. Use volume down button to go down to ‘Yes – ex. JawsNandRec1.1.zip’.
25. Press call button and installation will be started.
26. When you see ‘Install from sdcard complete’, press power button.
27. Press call button to select ‘reboot system now’.
28. Phone will be rebooted and enter NAND Android automatically.
29. Follow onscreen instructions to setup Android settings.
30. That’s all.
Good Luck
Just below are the files where you can download directly, exept for the radio, that you can get it here: Radio Leo 2.15.50.14
(If you are going for the 2nd method of ClockWorkMode, then depending on what type of roms you plan on using, you should download the partition size based on the following:
150MB Partition - For bare roms including CyanogenMod, AOSP, and MiUI
[*]250MB Partition - For Standard sense roms including Desire and EVo based ROMs, can also be used for some squashed HD builds
[*]400MB Partition - For Larger roms including unsquashed Desire HD and Z roms, ROMs REQUIRE data2sd for EU HD2 with 512MB NAND)
Well played sir and thanks for putting in the time to write this guide. Perhaps a passing mod would care to sticky this, either here or in a HD2 forum?
BTW, have an E-cookie for what is probably the best 1st post i've ever seen here
Totally agree. Even though I personally don't need this guide, I've still thanked you because I appreciate the time and effort you've put in, and that's just a brilliant 1st post!
Welcome to xda mate
+1 ....awesome Ist post, very useful for many.
Great guide!
Dear friend Gn,
thank you for your guide it is very detailed and precise but despite that fact
my ignorance(or stupidity) did't let me make the work. My mem is still 448mb, i thought after making the first two steps i'll had 576 of mem but it didn't work. At the first place i had 1.44 rom then i have change it in 1.66 with radio 2.15 but all that after installing Hspl.oops!!.
So now i have no idea how to proceed and put the android nand on. Can you help me please?
Thank you in advance
I think by memory he meant ROM not RAM
Since the first guide was useful to some people, I'm posting another one: How to Install NAND Android on HTC HD2 without ClockWorkMod Recovery. The first three steps are the same. All this stuff is not mine. I've just gathered other peoples postings. So all thanks shloud go to them. I'm just a bug.
How to Install NAND Android on HTC HD2 WITHOUT ClockWorkMod Recovery(updated 12 March 2011)
Prerequisites
HSPL3 ~ SPL-2.08.HSPL or HSPL4
Radio that support 576 RAM (ex. radio ROM 2.15)
DFT MAGLDR Bootloader
Make sure that you have all the prerequisites installed.
STEPS:
A1: Install HSPL3
or
A2: Install HSPL4
B: Install radio ROM 2.15
C: Install MAGLDR on HTC HD2
D: Install NAND Android on HTC HD2
A1: Install HSPL3
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
(To check your SPL version, hold the Volume Down button and do a reset)
You should have this SPL version unless you are using the latest 3.14 ROM with SPL 3.03.0000. No worry, just downgrade your Windows Mobile ROM from v3.14 to v1.66 will do. Download HTC HD2 v1.66 ROM. Then downgrade your phone from SPL 3.03.0000 to SPL 1.42.000.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL3_PKG.zip with 7-Zip.
10. Copy HSPL3_PKG.exe to desktop.
11. Execute HSPL3_PKG.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select ’2.08.HSPL’ to install.
16. After installation, you should see ‘We hacked it!’ on your phone.
17. Click on ‘Yes’ and your phone should be rebooted and load into Windows Mobile.
18. Disconnect USB cable from phone.
19. To verify, power off your phone.
20. Press volume down button (don’t let go) and power on your phone.
21. It will load into bootloader.
22. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
23. That’s all.
OR
A2: Install HSPL4
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
o SPL 3.03.0000 (for those using latest official HTC HD2 ROM v3.14)
(To check your SPL version, hold the Volume Down button and do a reset)
HSPL4 includes SPL-2.08.0000, SPL-2.08.HSPL, SPL-3.03.0000 and SPL-3.03.HSPL. The 3.03 SPL supports LEO1024.
You still need to use SPL-2.08.HSPL to use NAND Android and Windows Phone 7 and MAGLDR.
Make sure that you select the correct HSPL for your ROM installation.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL4.zip with 7-Zip.
10. Copy HSPL4.exe to desktop.
11. Execute HSP4.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select 2.08HSPL or 3.03HSPL. (This is to prevent people with 1024LEO's installing an incompatable version and bricking their device).
16. Click next
17. When its finished the phone should be rebooted and load into Windows Mobile.
18. Click ok to terminate program
19. Disconnect USB cable from phone.
20. To verify, power off your phone.
21. Press volume down button (don’t let go) and power on your phone.
22. It will load into bootloader.
23. You should get ‘Red, Green, Blue and White’ screen with SPL 2.08 or 3.03.
24. That’s all.
B: Install Custom Radio ROM
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
In order to flash custom radio ROM, you need to have HSPL3 installed on your HTC HD2. By the way, I used Radio Leo 2.15.50.14 on my guide. You can use it or any other HTC HD2 Radio ROM version.
HTC HD2 has 576 MB physical RAM but was reduced by software to 512 MB only. And custom Windows Mobile ROM + radio 2.07 or above can unlock it to be 576 MB again. Certain custom Windows Mobile ROM need higher radio version than your phone. And NAND Android requires it too. So you need to install custom radio ROM (if you don’t have the correct radio version).
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. I have R 2.06.51.07 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open Radio Leo 2.15.50.14.rar with 7-Zip.
11. Copy CustomRUU.exe and RUU_signed.nbh to desktop.
12. Execute CustomRUU.
13. Click ‘Yes’ if User Access Control prompt up.
14. Follow onscreen instructions to install.
15. Bootloader will be loaded with USB status during starting of installation. (~10 minutes)
16. Phone will be rebooted after installation finished.
17. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
18. Disconnect USB cable from phone.
19. That’s all.
C: Install MAGLDR
In order to install NAND Android on HTC HD2, you must install DFT MAGLDR Bootloader first. And the good news ~ both LEO512 and LEO1024 are supported. This means US T-Mobile HD2, Europe, Asia and the rest of the world’s HTC HD2 are supported.
Note – by installing MAGLDR, you cannot boot into Windows Mobile anymore. So everything on your phone is gone…
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
No worry, Android on NAND is working. That’s the reason we install DFT MAGLDR Bootloader on our HTC HD2, right? And we will be able to load a Windows Phone version when a new ROM comes out. Okay, let’s get started. If you don’t have HSPL3, please install it and also install radio ROM 2.15.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open DFT_LEO_MAGLDR113.rar with 7-Zip.
11. Copy MAGLDR113 folder to desktop.
12. Enter MAGLDR113 folder.
13. Execute ROMUpdateUtility.
14. Click ‘Yes’ if User Access Control prompt up.
15. Follow onscreen instructions to install.
16. Bootloader will be loaded with USB status during starting of installation.
17. Phone will be rebooted after installation finished.
18. DFT MAGLDR Bootloader will be loaded then.
19. Disconnect USB cable from phone.
20. That’s all.
D: Install NAND Android
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
* DFT MAGLDR Bootloader
Make sure that you have all the prerequisites installed.
Step by Step Guide
1. Power on your phone.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 5. USB Flasher.
4. Then press call button to load Android Flasher mode.
5. Connect USB cable from PC to phone.
6. Open your favorite ROM (ex. DFT_LEO_NAND_Android.rar) with 7-Zip.
7. Copy DFT_Android folder to desktop.
8. Enter DFT_Android folder.
9. Execute DAF.
10. Follow onscreen instructions to install.
11. Click ‘Yes’ if User Access Control prompt up.
12. Phone will be rebooted after installation finished.
Maybe the next steps are not obligatory, depending on the ROM you are going to install. In my case, I didn't have to follow the rest of the process, because the ROM I've used, has done the job itself and my phone was ready to work. (I've used CleanDroid and I had PERFCET results. Very light, clean and stable ROM. I've installed 30-40 apps and still is stable, alive and kicking.)
13. DFT MAGLDR Bootloader will be loaded then.
14. Use volume down button to go down to 3. Boot AD NAND.
15. Then press call button to load NAND Android.
16. Disconnect USB cable from phone.
17. Follow onscreen instructions to setup Android settings.
18. That’s all.
Alsomaybe the next steps are not obligatory.
To make auto boot to NAND Android.
1. Restart your phone.
2. Load to DFT MAGLDR Bootloader
3. Use volume up button to go up to 10. Services.
4. Then press call button to load Services Menu.
5. Then press call button again to enter AutoBoot settings.
6. Then press call button again to enter Boot source settings.
7. Select 3. Android from NAND with call button.
8. Use volume up button to go up to 10. Services again.
9. Then press call button to load Services Menu.
10. Then press call button again to enter AutoBoot settings.
11. Select 2. AlwaysMenu with call button.
12. Press power on/off button to select NO at Show boot menu always at boot?
13. Use volume up button to go up to 11. Reset.
14. Phone will be rebooted and enter NAND Android automatically.
15. That’s all.
Good Luck
install fresh Android ROM over dual boot hd2
I've set up dual boot to android and WP7 on my HTC HD2. I now wish to go back to only ANdroid on my phone. What are the steps for that. As my SD Card is partitioned will the new android rom be installed on just the NAND portion?
I need to know to what type of filesystem should I format my SD card so that i can install a fresh ROM.DO i need to go back to stock WM6.5 to install this.
Hi aditya_r12
Here's my newbie answer.
I think you can forget the sd card temporarily (remove it if you want),
flash a windows sytem (or just leave the existing win7) and then follow one of the above methods (the easier is the non clockwork mod), and you will be back to a nand android-only phone. After you can mount back your card with one or two partitions, or you can reparticion it or whatever.
I hope an experienced member, will also answer to you, since I'm an absolute ignorant newbie, which was lucky enough to manage to flash a perfeclty functioning android hd2, from scratch (thanks to the instructions of these nice people in this forum).
Good luck
Ho. Thanks for the reply. I finally got to installing nand android using clockwork mod. I used tadk29 to clear everything. Now I'd really like to know how to increase my internal storage
Its only some 250 MB right now. Is it possible to make it think that the storage extends to the SD card
gunjahman said:
Hi aditya_r12
Here's my newbie answer.
I think you can forget the sd card temporarily (remove it if you want),
flash a windows sytem (or just leave the existing win7) and then follow one of the above methods (the easier is the non clockwork mod), and you will be back to a nand android-only phone. After you can mount back your card with one or two partitions, or you can reparticion it or whatever.
I hope an experienced member, will also answer to you, since I'm an absolute ignorant newbie, which was lucky enough to manage to flash a perfeclty functioning android hd2, from scratch (thanks to the instructions of these nice people in this forum).
Good luck
Click to expand...
Click to collapse
Thank You~
I really need this faq but I thought there were newer versions of CWM that did not requier the "move to SD" files? Am I just totlly lost or is the faq older than those files?
Thank you for this guide. It will be very helpful for people like me (who don't read much unless encounter an issue) if download links will be available here also. So, it'll be a one stop shop guide..
I'm about to input the download links and the links for some video guides, as soon as I have the permission from the forum op.
Flashing a new nand android rom over a previous one
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE
(without clockwork mod)
Once you have flashed Magldr to your device you do not have to go through the whole process again if you want to flash a new NAND Android Rom:
1. Turn your phone off
2. Restart your phone by holding down the 'Power' button and keep holding it down until the Magldr Menu appears
3. Press the 'Volume Down' button to goto Option 4: USB Flasher and press the 'Call' button (far left of the 5 hardware buttons at the bottom)
4. Browse to the folder you extracted your NAND Android Rom files to on your pc, right click on Run DAF.exe (or install.exe if Daf.exe isnt listed) and select Run as Administrator (if using Windows Vista or Windows 7)
5. Read ALL the text and then select 'Next'
6. Read the information and select 'Next'
7. The installer will now detect USB and then flash your Android Rom to NAND
8. When flashing is complete your phone will Reboot and proceed to boot Android from NAND
That's all
Good Luck
Im a Evo user and trying to install Android on a buddys HD2. I am stuck at the pink stick together screen after step B completed and is trrying to redoot.. I dont think it wants to boot. Any ideas?
Apparently there are quite a few other benefits of installing CWM such as installing mods to your ROM. Unfortunately, I chose to install my present (and very stable) ROM without using CWM. Is there anyway to install CWM without losing my existing ROM?
gunjahman said:
After a lot of reading, I collect the following, just for my own aid. I hope it will be proved useful to others.
....
D: How to Install ClockworkMod Recovery on HTC HD2
Click to expand...
Click to collapse
thanks, i will give it a try
Perfect guide, thanks a lot. I completed the steps within an hour!
Greetings Readers,
Today you will learn how to unlock bootloader of your Mi A2 device along with flashing latest(as per now) TWRP(v3.5.0) subsequently flashing the latest(as per now) Resurrection remix OS(v8.6.5).
Your Phone's warranty would void. So you might wanna think again before going forward.
All of your device data would be wiped so create a backup beforehand.
Your device might get stuck in bootloop.
Your device might get damaged.
I won't be responsible for any ruckus you create.
Pre-requisites:
- Your phone's battery must be charged at least to 70%.- Keep your PC plugged into power as well.- Be confident.Lets Begin
Things Needed:
- Xiaomi Mi A2- PC(Windows recommended)- Data CableFiles Needed
File NameDownload LinkInstructionsRROS-Q-Final v8.6.5Resurrection Remix Downloads- Scroll down until you see a file: RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
- Now click on this file name to start the download.
*Gapps included in this ROM filetwrp v3.5.0Download twrp-3.5.0_9-0-jasmine_sprout.img-Click on the blue colored text: Download twrp-3.5.0_9-0-jasmine_sprout.img
twrp-installer v3.5.0Download twrp-installer-3.5.0_9-0-jasmine_sprout.zip- Click on the blue colored text: Download twrp-installer-3.5.0_9-0-jasmine_sprout.zip
platform-tools v31.0.0SDK Platform Tools release notes | Android Developers- Scroll down a bit and under Downloads section click on blue colored text: Download SDK Platform-tools for windows
- Now click on checkbox and then click on the download button to start the download:
Mi Unlock Tool v4.5.813.51miflash_unlock-en-4.5.813.51.zip-Dm Verity Force Encrypt Disabler v11.02.2020Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip-
*all the above given download links are from the respective official websites. So, download them all on your PC.
Preparing Mi A2
Enabling OEM Unlock and USB Debugging:
- Navigate to Settings > About phone.~ Tap on Build number 7 times.- Navigate to Settings > System > Developer options.~ Enable the 'OEM unlocking' and 'USB debugging' switch.- Switch off your phone.- Press the Power button and Volume Down button simultaneously, until you see the fastboot screen.- Connect the phone to your PC using USB data cable.
Working on PC
Installing drivers:
- Extract the 'miflash_unlock-en-4.5.813.51.zip' file.- Inside this file double click on 'miflash_unlock.exe' file.*we are not installing this tool. We are just using it for installing our device drivers.
- On the top right corner click on the settings gear icon.
- Now click on 'Check' button.
*it will ask for Administration Access twice.- Click on 'Yes' both the times.*a new dialogue box appears asking you to connect your device again.- Unplug your device and connect it again and the drivers will get installed.Unlocking Bootloader:
- Extract the 'platform-tools_r31.0.0-windows.zip' file.- Inside this file will be a folder platform-tools. Open it.- Now in the address bar type 'cmd' and hit enter.
*we did this in order to open cmd to this location. So that our future commands are accessible.- In the cmd window type the command:
Code:
fastboot devices
*it will display our device, something like this:
/* In case your device is not displayed.Try installing drivers again. */- Enter the command:
Code:
fastboot oem unlock
*this unlocks the bootloader temporarily/* A screen pops up on our phone.Navigate using volume buttons and select using power button.Our phone reboots.Set up everything haphazardly.Navigate to Settings and enable Developer options.Enable USB debugging in Developer options.Switch off your phone and boot into fastboot mode again. Enter the command fastboot devices in order to check if our device is successfully connected. */- Enter the command:
Code:
fastboot oem unlock_critical
*this will unlock our bootloader permanently/* Once again a screen pops up on our phone asking for a confirmation.Confirm it and phone reboots.Once again set it up haphazardly.Enable Developer options and USB debugging subsequently.Boot into fastboot mode again. */- Enter the command:
Code:
fastboot oem device-info
*this command will confirm if our device' bootloader has been unlocked or not
Installing twrp:
-Enter command:
Code:
fastboot format userdata
*this command wipes Internal Storage of our phone-Enter command:
Code:
fastboot format cache
*this command wipes cache of our phone-Now enter the command fastboot boot and drag and drop the 'twrp-3.5.0_9-0-jasmine_sprout.img' file into cmd and hit enter.*we did this so that command file will know the location of our twrp img file and hence execute the command/* Our phone will boot into recovery mode.Transfer 'twrp-3.5.0_9-0-jasmine_sprout.img', 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip', 'RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip' to Mi A2's Internal storage. */
Working on Phone- Tap on Install > Install Image(bottom right corner) button.- Select 'twrp-3.5.0_9-0-jasmine_sprout.img' file.- Now in 'Select Partition to Flash Image:' scroll down and select the 'Install Recovery Ramdisk' option.- Swipe right to flash.- Press back once flashing is complete.*temporary installed twrp in Slot B- Go to Home > Wipe > Advanced Wipe.- Tap on every checkbox except the 'Internal Storage'.- Swipe right to wipe.*we wiped the stock rom from Slot B- Go to Home > Reboot > Slot A.- Go to Home > Install.- Select the file 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' and swipe right to flash.*we temporary installed twrp in Slot A- Go to Home > Reboot > Recovery.- Tap on Wipe > Advanced Wipe.- Tap on every checkbox except the 'Internal Storage'.*we wiped stock rom from Slot A- Go to Home > Install.- Select the 'RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip' ROM file and swipe right to flash.*this might take some time- When flashing is finished tap on 'Wipe Cache/Dalvik' button.*we flashed RROS rom in Slot A- Go to Home > Install.- Select the 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' and swipe right to flash it again.*we installed twrp in Slot A again as it got wiped when we flashed our rom- Go to Home > Reboot > Slot B.- Go to Home > Install.- Select the 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' file and swipe right to flash.- Head back to Home > Wipe > Format Data.- Type 'yes' and tap on the Tick button.- Go to Home > Reboot > Recovery.- Go to Mount and tap on 'Enable MTP' button in the lower right corner (Do not press it if it's showing 'Disable MTP').- Now transfer the 'Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip' file into your phone's internal storage using your PC.- Go to Install and select the file 'Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip' and swipe right to flash.*we installed twrp permanently in slot B- Select the 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' and swipe right to flash it again.- Head to Home > Reboot > System.Congratulations we have successfully installed RROS on our Mi A2
How to boot into recovery:
Method 1: using Software
- Navigate to Settings > Resurrection tools > System > Power dialog.- Scroll down and under the 'BUTTONS' section, enable the 'Enable advanced restart' switch.-Now long press the power button and then select Advanced from the menu to see all the options.Method 2: using Hardware
- Switch off the phone.- Press Power button and Volume Up button simultaneously.- Just as you see Android Boot Splash Screen, press the Volume Up button twice.Bugs & Fixes
BugsFixesCamera isn't recording videos.- Head to Camera Settings.
- In 'Video quality' select 'FHD 1080p, 30fps' option.Phone stuck on boot splash screen when battery drains completely.
*this might occur for the very first time only- Boot into recovery using Power + Volume Up buttons.
- On twrp home screen, go to Reboot > Power Off.
- Switch On your phone by long pressing power button.Sometimes excessive tweaking delays device wake up.- Reboot SystemUI.
- Let the phone sit for a minute.Camera sounds not turning off.- Root your device using latest Magisk app.
- Now, install the module 'Disable screenshot and camera sounds'.
- Reboot your device.
Special Thanks to:
RROS Team for providing such a wonderful ROM.
TeamWin - TWRP for providing the twrp files.
@Zackptg5 for the Disable Dm-Verity file.
And to every person who made this possible.
Thankyou for Reading
You can turn on developer option turn on oem unlock. You can register on miui. Provide your mobile details they will give you unlock code. You can say you are developer and you want to unlock it.
Unlock code for android smartphone simcard
How to unlock android smartphone, what is mobile locking & how to check smartphone is locked or not. How to get sim network unlock code for mobile, different kind of cellphone carrier unlock codes. Requirement of generating sim unlock code from imei.
mobile-cellphones.blogspot.com
YOU TOMUCH WRITE, HUHH....
MY DEVICE XIAOMI MI A2 RAM 6 gb ROM 128 GB, THIS MONT I DOWNLOAD AND INSTAL ALL KIND JANK AND FINALLY I WIPE ALL THEN YESTERDAY HERE I DOUNLOAD RROS 8.6.7 OFFICIAL VANILLA,
HOW I INSTALL IT ON WIPED MI A2?
I USE APP RUBBIT XIAOMI ADB/FastbootTools.exe ONLY,
I INSTALL IMAGES OF OFICIAL FIRMWARE Q AND PBRP recovery NOT TO boot BUT TO Recovery, UNBELIVABLE BUT IT HAPPEN. AFTER FEW TIMES I ACCESS TO SDcard OF MI A2 FROM MY TOSHIBA FAKE NOTEBOOK OF YEAR 2008 WITH FAKE WINDOWS7 AND I COPY FILE RROS 8.6.7 FIRMWARE TO TWRP FOLDER CREATED WITH PBRP, ALSO FOLDER Tools FROM PBRP recovery.img
I INSTALL RROS TO a AND TO b, ALSO INSTALL Magisk, Supersu, AND NOT ONES, I DID it UNTILL SUCCESS.
I WANT TO TELL THAT IS AMAZING ROM NO GAPS I LOVE IT, BUT IT CHEAT ME WITH UPDATE TO LATEST RROS 8.6.9 YOU SEE 69 POSE WITH GAPPS, HUHH..
I AGAIN DELETE WIPE ALL RROS AND REINSTALL RROS 8.6.7 VANILLA NO WITH GOOGLE 69.
PLESE SEND TO VANILLA UPDATES WITH VANILLA AND TO RROS WITH GAPPS SEND UPDATES RROS GAPPS, IT NOT THE SAME.
AND PLEASE GIVE FILE boot.img FOR RROS 8.6.7 or 8.6.0 or 8.6.5 BECOUSE MAGISK NEED FILE boot.img AND I DO NOT KNOW WHY YOU SMART DEVELOPERS NEVER SHARE FILE boot.img WITH PRASED ROMS, THANK YOU.
NOW AFTER INSTALLING YOUR TWRP CAN NOT START IT STACK ON LOGO, NOT GOOD YOUR TWRP,
NEED boot_patched.img OF THIS RROS.
OK, I TRY AGAIN INSTALL TWRP 3.5.2 TO Recovery AND AGAIN INSTALL TWRP 3.5.2 TO boot AND INSTALL MAISK AND MagiskManagerRecovery TO ANABLE ROOT AND REBOOT AND IT STILL RUN RR LOGO
* * * * *
RROS 8.6.7 THE BEST ROM IT HAVE ANYTHING WE NEED EVEN BUTTON REMAPER IN THE SETTING, ALL MY BELOVED GAMES CAN RUN WITH THIS RROS ANDROID 10, EVEN J2MeRunner AND IT GAME LIKE Heroes Lore Wind of Soltia AND SuperWaterBomber, ALSO J2MeLoader WORKING AND CAN RUN ALL Java Jar Games, RROS THE BEST BUT I NEED ROOT FOR MY FRIEND LuckyPatcher
* * * * *
SO MANY TALKING ABOUT TOOLS AND adb TO UNLOCK BOOTLOADER,
I AM SORRY I AM SMARTER OR ALL AROUND MAD, JUST GO DEVELOPER OPTION AND TURN ON UNLOCK BOOTLOADER.
AND IN Xiaomi ADB/FastbootTools CLICK UNLOCK AND IT SAY ALREADY UNLOCKED THEN FLASH ANYTHING. I DID IT USING GARBAGE JUNK NOTEBOOK TOSHIBA J70 CHINES CLONE AND THERE SMARTERS PEOPLE USING LATEST WINDOWS AND PC ADVICE TO US adb MANY JUNK ZIP FILES I USE APP SIZE 2.9 MB AND NOTHING ELSE.
* * * * *
GOOD/ GOOD TWRP 5.3.2 AND PATCH ALSO GOOD BUT I MISTAKE AND INSTALL TWRP TO a AND TO b NOW I HAVE TWRP IN a AND b,
PHONE BOOTLOOP WHEN START a, AND WORKING OK WHEN START b, I NO UNDERSTAND WHY NOT YET I GET ROOT, SUPERSU NO WORKING, MAGISK EVERY 3 OPTIONS YES BUT INSTALLED SHOW N/A, I INSTALL MAGISK FROM TWRP HUNDRED TIMES AND NOT YET ROOT, IT ASKED ME FOR boot.img
MAYBE NEED PATCH TWRP.. AND INSTAL IT IN 101 TIME..
eleven.co said:
Greetings Readers,
Today you will learn how to unlock bootloader of your Mi A2 device along with flashing latest(as per now) TWRP(v3.5.0) subsequently flashing the latest(as per now) Resurrection remix OS(v8.6.5).
Your Phone's warranty would void. So you might wanna think again before going forward.
All of your device data would be wiped so create a backup beforehand.
Your device might get stuck in bootloop.
Your device might get damaged.
I won't be responsible for any ruckus you create.
Pre-requisites:
- Your phone's battery must be charged at least to 70%.- Keep your PC plugged into power as well.- Be confident.Lets Begin
Things Needed:
- Xiaomi Mi A2- PC(Windows recommended)- Data CableFiles Needed
File NameDownload LinkInstructionsRROS-Q-Final v8.6.5Resurrection Remix Downloads- Scroll down until you see a file: RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip
View attachment 5226269
- Now click on this file name to start the download.
*Gapps included in this ROM filetwrp v3.5.0Download twrp-3.5.0_9-0-jasmine_sprout.img-Click on the blue colored text: Download twrp-3.5.0_9-0-jasmine_sprout.imgView attachment 5226271twrp-installer v3.5.0Download twrp-installer-3.5.0_9-0-jasmine_sprout.zip- Click on the blue colored text: Download twrp-installer-3.5.0_9-0-jasmine_sprout.zipView attachment 5226273platform-tools v31.0.0SDK Platform Tools release notes | Android Developers- Scroll down a bit and under Downloads section click on blue colored text: Download SDK Platform-tools for windows
View attachment 5226281
- Now click on checkbox and then click on the download button to start the download:
View attachment 5226285Mi Unlock Tool v4.5.813.51miflash_unlock-en-4.5.813.51.zip-Dm Verity Force Encrypt Disabler v11.02.2020Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip-
*all the above given download links are from the respective official websites. So, download them all on your PC.
Preparing Mi A2
Enabling OEM Unlock and USB Debugging:
- Navigate to Settings > About phone.~ Tap on Build number 7 times.- Navigate to Settings > System > Developer options.~ Enable the 'OEM unlocking' and 'USB debugging' switch.- Switch off your phone.- Press the Power button and Volume Down button simultaneously, until you see the fastboot screen.- Connect the phone to your PC using USB data cable.
Working on PC
Installing drivers:
- Extract the 'miflash_unlock-en-4.5.813.51.zip' file.- Inside this file double click on 'miflash_unlock.exe' file.*we are not installing this tool. We are just using it for installing our device drivers.View attachment 5226331- On the top right corner click on the settings gear icon.View attachment 5226333- Now click on 'Check' button.View attachment 5226335*it will ask for Administration Access twice.- Click on 'Yes' both the times.*a new dialogue box appears asking you to connect your device again.- Unplug your device and connect it again and the drivers will get installed.Unlocking Bootloader:
- Extract the 'platform-tools_r31.0.0-windows.zip' file.- Inside this file will be a folder platform-tools. Open it.- Now in the address bar type 'cmd' and hit enter.View attachment 5226371*we did this in order to open cmd to this location. So that our future commands are accessible.- In the cmd window type the command:
Code:
fastboot devices
*it will display our device, something like this:View attachment 5226381/* In case your device is not displayed.Try installing drivers again. */- Enter the command:
Code:
fastboot oem unlock
*this unlocks the bootloader temporarily/* A screen pops up on our phone.Navigate using volume buttons and select using power button.Our phone reboots.Set up everything haphazardly.Navigate to Settings and enable Developer options.Enable USB debugging in Developer options.Switch off your phone and boot into fastboot mode again. Enter the command fastboot devices in order to check if our device is successfully connected. */- Enter the command:
Code:
fastboot oem unlock_critical
*this will unlock our bootloader permanently/* Once again a screen pops up on our phone asking for a confirmation.Confirm it and phone reboots.Once again set it up haphazardly.Enable Developer options and USB debugging subsequently.Boot into fastboot mode again. */- Enter the command:
Code:
fastboot oem device-info
*this command will confirm if our device' bootloader has been unlocked or notView attachment 5226413
Installing twrp:
-Enter command:
Code:
fastboot format userdata
*this command wipes Internal Storage of our phone-Enter command:
Code:
fastboot format cache
*this command wipes cache of our phone-Now enter the command fastboot boot and drag and drop the 'twrp-3.5.0_9-0-jasmine_sprout.img' file into cmd and hit enter.*we did this so that command file will know the location of our twrp img file and hence execute the command/* Our phone will boot into recovery mode.Transfer 'twrp-3.5.0_9-0-jasmine_sprout.img', 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip', 'RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip' to Mi A2's Internal storage. */
Working on Phone- Tap on Install > Install Image(bottom right corner) button.- Select 'twrp-3.5.0_9-0-jasmine_sprout.img' file.- Now in 'Select Partition to Flash Image:' scroll down and select the 'Install Recovery Ramdisk' option.- Swipe right to flash.- Press back once flashing is complete.*temporary installed twrp in Slot B- Go to Home > Wipe > Advanced Wipe.- Tap on every checkbox except the 'Internal Storage'.- Swipe right to wipe.*we wiped the stock rom from Slot B- Go to Home > Reboot > Slot A.- Go to Home > Install.- Select the file 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' and swipe right to flash.*we temporary installed twrp in Slot A- Go to Home > Reboot > Recovery.- Tap on Wipe > Advanced Wipe.- Tap on every checkbox except the 'Internal Storage'.*we wiped stock rom from Slot A- Go to Home > Install.- Select the 'RROS-Q-Final-8.6.5-20201215-jasmine_sprout-Official-gapps.zip' ROM file and swipe right to flash.*this might take some time- When flashing is finished tap on 'Wipe Cache/Dalvik' button.*we flashed RROS rom in Slot A- Go to Home > Install.- Select the 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' and swipe right to flash it again.*we installed twrp in Slot A again as it got wiped when we flashed our rom- Go to Home > Reboot > Slot B.- Go to Home > Install.- Select the 'twrp-installer-3.5.0_9-0-jasmine_sprout.zip' file and swipe right to flash.- Head back to Home > Wipe > Format Data.- Type 'yes' and tap on the Tick button.- Go to Home > Reboot > Recovery.- Go to Mount and tap on 'Enable MTP' button in the lower right corner (Do not press it if it's showing 'Disable MTP').- Now transfer the 'Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip' file into your phone's internal storage using your PC.- Go to Install and select the file 'Disable_Dm-Verity_ForceEncrypt_11.02.2020.zip' and swipe right to flash.*we installed twrp permanently in slot B- Head to Home > Reboot > System.Congratulations we have successfully installed RROS on our Mi A2
How to boot into recovery:
Method 1: using Software
- Navigate to Settings > Resurrection tools > System > Power dialog.- Scroll down and under the 'BUTTONS' section, enable the 'Enable advanced restart' switch.-Now long press the power button and then select Advanced from the menu to see all the options.Method 2: using Hardware
- Switch off the phone.- Press Power button and Volume Up button simultaneously.- Just as you see Android Boot Splash Screen, press the Volume Up button twice.Bugs & Fixes
BugsFixesCamera isn't recording videos.- Head to Camera Settings.
- In 'Video quality' select 'FHD 1080p, 30fps' option.Phone stuck on boot splash screen when battery drains completely.
*this might occur for the very first time only- Boot into recovery using Power + Volume Up buttons.
- On twrp home screen, go to Reboot > Power Off.
- Switch On your phone by long pressing power button.Sometimes excessive tweaking delays device wake up.- Reboot SystemUI.
- Let the phone sit for a minute.Camera sounds not turning off.- Root your device using latest Magisk app.
- Now, install the module 'Disable screenshot and camera sounds'.
- Reboot your device.
Special Thanks to:
RROS Team for providing such a wonderful ROM.
TeamWin - TWRP for providing the twrp files.
@Zackptg5 for the Disable Dm-Verity file.
And to every person who made this possible.
Thankyou for Reading
Click to expand...
Click to collapse
THE BEST ROM THANK YOU.
ALWAYS PROBLEM UNABLE CREATE CACH OR SYSTEM SOLVED BY WIPING ALL EXEPT ENTERNAL AND INSTALLING TO RAM DISC NOT TWRP 3.5.0_9 BUT TWRP 3.2.3 AND IT FLASHING CLEARLY TO CURRENT SLOT FROM a TO a, FROM b TO b WITHOUT RED LETTERS ABOUT ERROR, SO IN ORDER to FLASH RROS AND PATCH AND MAGISK NEED TWRP 3.2.3 jasmine sprout.img
И НИКАКИХ ТАНЦЕВ С БУБНОМ,
НУЖЕН ЗАЯЦ В УШАНКЕ 2.9 mb.exe И TWRP 3.2.3, ПРОШИВКА СУПЕР
LUCY YISRAEL said:
ALWAYS PROBLEM UNABLE CREATE CACH OR SYSTEM SOLVED BY WIPING ALL EXEPT ENTERNAL AND INSTALLING TO RAM DISC NOT TWRP 3.5.0_9 BUT TWRP 3.2.3 AND IT FLASHING CLEARLY TO CURRENT SLOT FROM a TO a, FROM b TO b WITHOUT RED LETTERS ABOUT ERROR, SO IN ORDER to FLASH RROS AND PATCH AND MAGISK NEED TWRP 3.2.3 jasmine sprout.img
И НИКАКИХ ТАНЦЕВ С БУБНОМ,
НУЖЕН ЗАЯЦ В УШАНКЕ 2.9 mb.exe И TWRP 3.2.3, ПРОШИВКА СУПЕР
Click to expand...
Click to collapse
Thankyou for your suggestions and corrections. I'm glad that you did it.