hi hope someone can help me.i tried updati ng my xda exec after downloading the rom update from o2, and now my pc doesnt recognise the xda and my xda doesnt start its gone completely bank.i tried holding the softkeys and pressing the reset button, it says hit 0 to get back to factory settings and nothing happens........please it looks like my phones gone comatose
Moved to Uni Upgrade forum form Upgrade general
i believe u r stuck in bootloader
hi
try the following
disable usb connection from connection settings in active sync
then re upgrade the rom , and when you reach the screen where it tells u the rom version (it wont tell u this time) u ll HAVE to wait for few seconds before pressing "upgrade" , hopefully it will work this time
good luck
hi
hi there, i tried upgrading my 02 xda executive from the software update on O2 website.my active sync 4.1 stopped working in midst and my xda is nt working now.and my pc isnt recognising the xda. the xda isnt starting up its completely dead.I tried hitting the 2 softkeys and the soft reset button and the screen lights up and it says to rollback to factory setting hit 0 zero, but nothing happens................plz help would be appreciated.http://www.my-xda.com/xdaExecSoftware.jsp
also the screen now has USB and v1.00 over it and shows nothing but this and not starting up and my pc pops a message up saying that an unknown usb device and cant be connected
Does anybody have a solution to the above problem as I now have 2 xda execs in the same situation. It's a bloody nightmare! I understand it's in bootloader mode. Just don't know how to get the xda up and running again without sending it off to O2...
Please help!
LOOK HERE I have been in this situation myself a couple of times. Personally I use method 2 which is at the bottom of the page as it's very easy to follow. I suggest you try this method first.
Regards,
Psi
Those of you having trouble after a Rom Flash. If it goes wrong, start by pressing THE BACKLIGHT BUTTON, THE POWER BUTTON AND PRESS IN TO THE SOFT RESET HOLE ALL at the same time. This should put you back into BOOTLOADER. Then try your rom flash again. If the WM6 fails I re-flashed with the O2 EXEC WM5 first. Forget Active Synch saying it cant etc.
Providing you can just see some very faint words then you are back in bootloader. I have got the original O2 XDA EXEC WM5 Rom files so if you want them, as I can not find out how to put a large zip file on here then I can email it to you. Let me know on
[email protected]
pls i need it send to [email protected]
Related
NEED HELP!!!!
i was trying to upgrade my xda IIs to
"ba_o2asia_14000_923_11200_ship (1.40.00)",
then when it comes to the third part "windows ce" it wont continue.
ived tried everthing like uninstalling and installing the active sync, reboot the pc and soft reset the unit.......
now all that appers on my screen is "USB, v2.07" and i cant use my unit.....
plus when i click connect in active sync on my desktop it wont detect my device.
HELP ASAP!!!
Try a Hard Reset
Try a Hard Reset, Power button + Reset hole at the same time, if it doesnt work after that you need to try again from the begining. try the BA for beginers WIKI http://wiki.xda-developers.com and look for someone with the same device as you in the same country in the forums, check what ROMs they are using in there Sig in order to find the most suitable ROM to try and install that one..
Having said this i am not an expert buy any means, but this is what I have done.
After I just installed my new Radio Rom this morning I was prompted to hard reset, I'm sure this is what you have to do affter a full ROM update, good luck.
The v2.07 dosnt mean youve ruined it so keep trying.. :wink:
i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
keep on doing a hard reset until you reach bootloader mode. from there try upgrading again. were you upgrading to 2003se or wm2005?
i was installing the rom from 02 web site
i was installing the rom from the 02 web site.i had tried but it did not open boatloader.what i can i do?
anything showing on your xda screen? if it's blank then you have to continue doing hard resets. a buddy of mine had the same problem and he was able to bring it back to bootloader mode after 10 or so hard resets.
if something is showing on the screen (like "usb version...something") then this is already bootloader mode. what you do is put the xda back on the cradle but don't expect activesync to recognize it. just put it back on the cradle and then rerun the upgrade.
hope it works.
rob
there is only o2 logo on the device,i tried hard reset but it did not open boatloader
I follow instruction in http://forum.xda-developers.com/showthread.php?t=313486 but after hardreset.
My p800w is stuck in T-Mobile logo and version number. It can't continue booting up to windows mobile.
Question: How to flash ROM without ActiveSync?
How to recovery my Artemis?
Welcome any advice,
Thanks in advance.
Yea me to, mine is now a brick after that upgrade? No active sync connection possible and all I get now is the blue O2 start screen after the hard reset with the red writing and numbers in the top left hand corner..
Phone is an UK XDA Orbit
IPL 1.25.0001
SPL 1.11.0000
GSM 02.67.90
OS 3.4.0.0
HELP!!!!!!!
yeah, I had the same problem and have created a thread for it already. unfortunately I got no useful replies, and it seems that I am stuck waiting for an official o2 ROM so that I can recover my Orbit.
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
motomob said:
It seems there is a way to un brick our phones I just need to get my phone bootted into bootlader mode which no one seems to say how to do??
Can anyone help how I can boot my Orbit , like what combo of keys I need to press to boot it into bootloader mode then XP will see it at a driver level apparently Active Sync still won;t but I will be able to run some German ROM update with the ROM file replaced with the other ones and it may come back to life..
Help how can I boot my phoen in bootloader mode???
Click to expand...
Click to collapse
I read in here that you hold the voice button and soft reset.
Decaf said:
I read in here that you hold the voice button and soft reset.
Click to expand...
Click to collapse
Correct and use mtty
Already see in the forum ....
Thanks guys and apologies for the spelling..I ran the Artemis_USPL before I tried upgrading to WM6 and again have been able to run it after with my new brick now with the phone in bootloader mode but still when I try and run the german ROM update a) it will only work with the german file which freezes @ 3%? This seems to be a known problem reading around and b )when I replace it with the smaller ROM file, 54MB the german one is 66MB, I originally tried to use it doesn't read the ROM file or the update utility doesn't want to read it. I reckon I might be able to get it back if I can get one of the ROM update utilities to read a good ROm file and send it to the phone.
I can;t find this MTTY program to sniff the USB port and return the code of if the USPL util wokred as I think that could be key to all of this.
Can anyone post a quick how to here for
1) install MTTY from somewhere
2) what command to run agaist the phoen to see if the USPL util worked and what values I should be looking for
3) another WM6 ROM version (that the update utils can read) download location I can download from to try and send to the phone using the German update util
Not asking for much am I but I desperately need my phone back WM5 or 6 in the next day or so so really can't send it off.
Thanks
Error message I recive at the 3% stage when using the German ROM and english update util.
use the file attach and read that :
http://forum.xda-developers.com/showthread.php?t=285112
Thanks but I'm not that cleud up on what commands I'm meant to be sending. It works in Bootloader mode I ge a response from the phone by send it a command. But even if I get a response telling me what the CID status is its not much help as I think ti shoudl have tekane BEBEs ROM by now as I've got the german ROMUpdateUtility sending that 54,272KB file to the phone but it stops after 3%. What are my options?
motomob said:
But even if I get a response telling me what the CID status is its not much help as I think
Click to expand...
Click to collapse
That's right. On older models MTTY was quite useful, but not on the Artemis. You cannot use it to read the CID status anyway. If you are not sure about the status, run the USPL tool, just to make sure.
I've already re run the USPL ROMUpdateUtility and it completes 100% okay in bootloader mode. But after I hard reset and then try and flash the WM6 BEBE ROM or any ROM German etc back onto it it either fails with the error code I posted up earlier or gets to 3% and fails.
What are my options at this stage? Does anyone have a link to another ROM I can try like the original WM5 O2 ROM or any other WM6 ROm that might work. I'm willing to give them all a try as it's just a useless phone right now and I haven;t sent it off as 1) I need it before the weekend and 2) As I can flash some ROMs with the USPL and others have done this no problem I really feel there must be a solution as I can still falsh the phone.
What can I say RTFM... I did it all right and I didn't have a brick, I missed out one small detail... loading on the ROM with the extended ROM. All now running and it does seem a little faster than WM5.
Thank you to all those that tried to help out. To the others that are still having probs.. Don't try and run the update in the middle of a busy day in the office whilst trying to manage 100 other things meaning you are probably missing out a line like me...
One question though how do I get back my O2 power and storage meters on the today screen back as I liked them and the WiFi seems to have a bug where when it is enabled and you click on the WiFi symbol up the top it only allows you to switch it on, when it is already on.. so you have to open up the COMM manager to switch it off.
So how did you fix it exactly? I have read this thread thoroughly and can't find out what you did!
ERROR[206] occurs while trying to update ROM to WM6
While tring to update ROM to WM6 on O2 XDA Orbit i encounter ERROR[206].
I wanted to attach the screen shot but dont know how to do that, but anyway what i am doing is i attached my pda to my pc via activesync using supplied usb cord. Everything goes well till i reach a screen where it says "You are now ready to update your ROM image...." and once i click next a progress bar apperas and my pda shuts and activesync exit's automatically and my pda tries to restart with RBG band and some text:RUU, IPL 1.25.0001, SPL 1.25.0000 and USB. And thats it after few seconds or a min i get the ERROR[206] and my pda hangs.
I dont know why Activesysn shutsdown ???
Just an additional in i want to tell that without installing activesync i am not able to connect/pair my pda with my pc. So do i need to install the drivers and then try or it doen't matter cause once i install Active sync i can connect the device.
Please help me with this....
Thanks
unable to load bootloader!!!!!!!!!!!!
HELP!!!!!!!!
I have HTC3300, tried to update rom, now its bricked. I tried to start bootloader by pressing the voicebutton and softreset but loads in t-mobile screen and hangs, im unable to start the bootloader.
Is this end of story or are there any other options to get the bootloader to start????
please help
Bootloader
I had a problem with my phone loaded touch flow 4 and cid unlocking, everything was fine then after a while it froze at boot up.
I look put the battery and did a hard reset, put it into bootloadeder mode, reflashed with a t-mobile rom does not need to be cid unlocked to do that.
Once origonal rom was working, cid unlock again, flashed back to touchflow 4.0 - sorted
Where did you got an tmobile rom from can you tell me. Mine is also freezing on booting almost once every day or so after I've upgraded to 4.0
Hi Guys,
I tried to flash the o2 rom from buzzdev.net (latest one). All went well, but when I tried to do hard reset it comes back with the usal white screen (0 to restore defulat and x to exit). When pressing 0 the screen turns into garbage. Have I bricked my phone or can I save it? Please help ...
Thanks
my xda not working after installing O2 xda rom from buzzdev.net - FIXED
Sorry guys I panicked.
I had the problem, and then I followed some instructions on this forum, you have to press the light button plus the back light to get into bootloader and reflash. But it won't wokr on mine. Then I found out cause the usb cable was connected to the monitor (monitor has 2 usb ports connected to the laptop). Once I connected directly to the laptop I was able to get into the bootloader and reflash Phew ... Nearly had a heart attack. Perhaps someone else will learn from this.
Hey help me please!!
Please brother's help me!!
I have a Diamond, and yesterday I try to upload my phone with a rom
At the moment it's load perfectly, so after the program has finished the atualization, my phone make a soft reset(normal), So when wake up, and show's me a boot screen with (TOUCHdiamond) name on the screen, he freeze!!
I can't do nothing! It's stuck!? omg! people help me to resolve this!? I try up a new rom but isn't work cause the phone don't connect with windows to change or execute other program, cause the phone are stuck on boot screen!
Please!!! HELP ME TO RESOLVE!!! PLEASE!!!!!
c ya!
thx for all
dehzincwb said:
Hey help me please!!
Please brother's help me!!
I have a Diamond, and yesterday I try to upload my phone with a rom
At the moment it's load perfectly, so after the program has finished the atualization, my phone make a soft reset(normal), So when wake up, and show's me a boot screen with (TOUCHdiamond) name on the screen, he freeze!!
I can't do nothing! It's stuck!? omg! people help me to resolve this!? I try up a new rom but isn't work cause the phone don't connect with windows to change or execute other program, cause the phone are stuck on boot screen!
Please!!! HELP ME TO RESOLVE!!! PLEASE!!!!!
c ya!
thx for all
Click to expand...
Click to collapse
Here's what you need to do:
Hold down the "Volume Down" button and press reset with the stylus. You will enter the Boot Loader. Now plug in your USB cable connecting it to you PC. On the bottom part of the screen (phone) you'll see USB. Now your PC recognizes the phone.
Start a ROM update through the RUU executable and flash your phone with a different ROM.
henk2484 said:
Here's what you need to do:
Hold down the "Volume Down" button and press reset with the stylus. You will enter the Boot Loader. Now plug in your USB cable connecting it to you PC. On the bottom part of the screen (phone) you'll see USB. Now your PC recognizes the phone.
Start a ROM update through the RUU executable and flash your phone with a different ROM.
Click to expand...
Click to collapse
thx!! really appreceate!!! thx! it's back to work! thx!!!!!
i have the same problem where my phone freezes at the boot screen, where it says touch diamond and thw orange writing in the corner. It was working fine, happened all of a sudden after i soft reset it, when the phone initally froze on an incoming call
Any suggestions?
just Change your ROM..,
hard reset is somthing i dont want to do. Is there any other option?
kerm said:
hard reset is somthing i dont want to do. Is there any other option?
Click to expand...
Click to collapse
I think not. Don't know if you have a lot of apps installed after flashing. What you could do is find a ROM that's UC2/sUC compliant. If you create a folder structure on your internal storage like this:
ROOT > Backup and Restore > CAB > CABi
Put all the cabs you want on your device in the CAB folder and all the cabs you want on internal storage in CABi folder. After flashin and initial customization you will find yourself in User Customization (UC). It will state that it found a CAB folder, choose to install. After this it will state that it found a CABi folder, install as well. This reduces the effort of installing all apps after a hard-reset. As for messages, contacts e.g. I suggest you use PPCPimBackup.
same problem, but when I launch the ruu all is ok, until it starts, it stay at 0%, then I get a message that there was a communication error
Go1den3ye said:
same problem, but when I launch the ruu all is ok, until it starts, it stay at 0%, then I get a message that there was a communication error
Click to expand...
Click to collapse
Try flashing through bootloader. Press reset with stylus while holding volume down. After you're in the bootloader plugin USB cable and start flashing.
henk2484 said:
Try flashing through bootloader. Press reset with stylus while holding volume down. After you're in the bootloader plugin USB cable and start flashing.
Click to expand...
Click to collapse
tried and didnt work. made it worst in fact :S
startet update trough bootloader, started, updated to 13% and then I was told the update didnt work with my device (or something similar, in norwegian). tried an older update, same problem... :/
when I now boot the phone I'm directly in bootloader, and with the funny message
DIAM100 65M
SPL-2.03.0000
PSOC-Diam STAGE_PVT v0x30
Upgrade ROM code error
Please try again
I might have my hand on a brick... but hope not...
edit:
ooh, news, suddenly its updating moore... after 5 tries it allways stopped at 13%, but now it up to 31% and going strong... will update..
edit2: going strong up to 33%....... wow... well its a start and Im going to try some more.
edit3; 7th time the charm it seems... 100% and all I had to do was sit REALLY still. and I actually downgraded from 2.03 to 1.93 or something... should note that on this point I have tried flashing it with the original 2.03 and 1.93 every other time...
edit4; aaaaand we're back at the TOUCH Diamond screen.
edit5; aaaand after a failed flash to wm 6.5 (stopped/didnt start at 0%)... the phone started... This MIGHT be a clue that I should NOT try to get wm6.5 to run... but that wont stop me
I dont know if anyone else will have the same problems, but atleast this was my way to the resolution
Go1den3ye said:
tried and didnt work. made it worst in fact :S
startet update trough bootloader, started, updated to 13% and then I was told the update didnt work with my device (or something similar, in norwegian). tried an older update, same problem... :/
when I now boot the phone I'm directly in bootloader, and with the funny message
DIAM100 65M
SPL-2.03.0000
PSOC-Diam STAGE_PVT v0x30
Upgrade ROM code error
Please try again
I might have my hand on a brick... but hope not...
edit:
ooh, news, suddenly its updating moore... after 5 tries it allways stopped at 13%, but now it up to 31% and going strong... will update..
edit2: going strong up to 33%....... wow... well its a start and Im going to try some more.
edit3; 7th time the charm it seems... 100% and all I had to do was sit REALLY still. and I actually downgraded from 2.03 to 1.93 or something... should note that on this point I have tried flashing it with the original 2.03 and 1.93 every other time...
edit4; aaaaand we're back at the TOUCH Diamond screen.
edit5; aaaand after a failed flash to wm 6.5 (stopped/didnt start at 0%)... the phone started... This MIGHT be a clue that I should NOT try to get wm6.5 to run... but that wont stop me
I dont know if anyone else will have the same problems, but atleast this was my way to the resolution
Click to expand...
Click to collapse
Before you try to flash anything other then a stock ROM, I suggest you take a look at this thread: http://forum.xda-developers.com/showthread.php?t=416211
You need to have Hard-SPL flashed before flashing any custom ROM. My advice would be to use this one: http://forum.xda-developers.com/attachment.php?attachmentid=93362&d=1213719705
cool, will try that one. thnx
On My New Diamond having 1.37 Asian HTC ROM i Flashed 1.93 Asian HTC ROM. It flashed successfully then after installing some programs i have done the soft reset after that It hangs on Operator (Airtel) Logo and my phone doesn't start. I have not installed
any Hard SPL.
I have done Vol.Down + Softreset button but nothing appears on screen.
I tried to Hard Reset but nothing Happens
plz plz help me
dalco said:
On My New Diamond having 1.37 Asian HTC ROM i Flashed 1.93 Asian HTC ROM. It flashed successfully then after installing some programs i have done the soft reset after that It hangs on Operator (Airtel) Logo and my phone doesn't start. I have not installed
any Hard SPL.
I have done Vol.Down + Softreset button but nothing appears on screen.
I tried to Hard Reset but nothing Happens
plz plz help me
Click to expand...
Click to collapse
Did you hold the volume down button while pressing reset? After pressing reset you should keep holding the volume down button until the tri-color bootscreen appears.