I have looked all over the Blue Angel Support forum and I was able to get the latest rom which includes the latest Radio 1.08 (I know there is 1.10 but I do not think it is available for cooking yet). I was wondering where everyone was getting this bluetooth stack from (as well as the BT3500 version) and most importantly if these two stacks support A2PD profile (High quality Headphone profile). I have this older PDA2K Broadcom cab file I got over the the firstloox forum that actually worked with my Loox 720, but I think it is a pretty old version. Do these two broadcomm stack versions include this profile and where can I get them and willI have to hardreset to install them or are they available as cab files?
Also with bluetooth on the PDA2k, is it possible to passthrough all the sound that happens in Windows mobile through the headset e.g. Music, videos, etc or is it only phone sounds that go through the headset? And are there any bluetooth headsets that can redial the last number dialed on my PDA2K using a button on the headset?
Look in WIKI for BT cabs.
http://wiki.xda-developers.com/index.php?pagename=BA_Versions
(instructions for both 1.08 and 1.10 written by other forum members)
I use an I-tech headset (not sure if available in the States) this has a redial button (two short clicks)
I have last number dialed set to my answer phone, on Orange I use the Wildfire answer phone which has voice recongnition.
I can therefore dial any number using my blue tooth device.
this is exactly what I want to do. What did you use to set the answer button to last number redial. How exactly do I do this on my pda2k with a headset that has an answer button. Is it done on the headset itself or is it done on the pda2k with a special program or app? If you don't mind could you go into detail about this as this would solve the voice dial over bluetooth problem plaguing these devices as I could always use the voice service of my carrier (CIngular wireless in the US).
Have they fixed this yet. Is there any software out there for the PPC 6601, that will allow a bluetooth headset to use voice commands to dial or operate the PDA by voice through the headset.
Sprint PPC 6601, running Windows Mobile 2003 CE SE.
Jabra BT800 Bluetooth Headset.
From what I have gathered so far from reading the threads is that I will first need to upgrade to WM5? Will my 128meg of ram be enough for this?
My bluetooth on WM2003 SE seems to be version 1.0 is there a patch to upgrade that to 1.2 or is that WM5 only. Also im new here so if anyone knows any threads that have instructions on how to do this will help me out greatly thx.
I just tried several Wm6 roms on both my Trinity and Hermes. It seems all the new RTM roms now work correctly with the earpiece speaker using VOIP on the Hermes, this is using CUSTEL VOIP.cab and/or built in VOIP in the various Hermes RTM roms. However on the Trinity we get no sound alot of times, and when we do it sounds on the back speaker and doesnt work with bluetooth unlike the hermes. ANyone know why this is?
mcq3000 said:
I just tried several Wm6 roms on both my Trinity and Hermes. It seems all the new RTM roms now work correctly with the earpiece speaker using VOIP on the Hermes, this is using CUSTEL VOIP.cab and/or built in VOIP in the various Hermes RTM roms. However on the Trinity we get no sound alot of times, and when we do it sounds on the back speaker and doesnt work with bluetooth unlike the hermes. ANyone know why this is?
Click to expand...
Click to collapse
not sure... how about asking on the trinity forums instead of the hermes forums ???
Both Hermes and Trinity are amongst the supported devices in AGEphone Mobile 2.5 Speakerphone Edition! Forget about the crappy internal client and use a real softphone
VOIP Blutooth Hermes
I got a Herme's and i Just got VOIP to work. (SIP, Vbuzzer)
but when i dial out with it, i dont have any sound comming through my Bluethooth headset
(Blacks 3.1 rom)
To make your BT-headset work with the current version of AGEphone, please follow the following instructions:
There is no official support for Bluetooth Headsets yet, but you can make most of them work with AGEphone using a little hack. There is no need to change the audio device in AGEphone for this at the moment. You only have to use a little tool called "BTAudioToggle.exe". For further information about this utility please refer to this thread. The package you can download there contains "BTAudioOn.exe" / "BTAudioOff.exe", but using "BTAudioToggle.exe" does the job just fine. Once you have downloaded the utility please go to "Settings - Other" and give AGEphone the path to the "BTAudioToggle.exe" file there for "Execute on Connect" and "Execute on Disc." without any further parameters. If your BT headset is paired properly with your phone AGEphone will automatically switch output and input to the device whenever you accept a call. It's probably of note that BTAudioToggle.exe only works with the Microsoft Bluetooth Stack.
This allows you to use the headset not only with AGEphone Mobile but any other program. I hope it helps!
hi all,
i'm having issues with my agephone mobile 2.64. i'm connecting it with gizmo5 and grandcentral and my hermes.
i call grandcentral, agephone shows that it has a call (no sound), i accept (still no sound), press one (cause i know i need to press 1), then the call connects.
but there is no audio in both ends, i can't hear the other side and i can't talk to the other side.
any one know if a way to fix this?
Earpiece workig ?
The new version is here:
[APP][FREE] audioRoute 1.2.010 for VoIP
http://forum.xda-developers.com/showthread.php?t=495166
After upgrade to the official HTC WM6 ROM (spanish version) my integrated bluetooth hansdfree CAR-KIT doesn't work anymore (with WM5 the system works perfectly).
The car is a new CITROËN C4 Picasso, but i think this problem must involve any new PSA Group Car (CITROËN, PEUGEOT...) that mount the same kit.
I can pair the CITROËN hansfree with the TyTN, and both connects (i can see the operator name, the battery level, and the signal level, that WM5 stack doesn't show) but when i try to call, or i receive a call, there is no sound throw the hansfree system.
I also have tried the Jetware bt extension with no succes.
At now i had to downgrade to WM5 because this problem (i need the handsfree working).
The cuestion is...
Is it possible for a ROM MASTER to extract a previous bluetooth working TyTN stack to overwrite the stack that comes with official WM6?... (the WM5 or any working WM6 working stack).
Thanks
The same problem here with the same car; also the Artemis on WM6 (I tried several roms) has no sound.
Downgraded to WM5, and it's all working again.
Not yet tried to get an update for the car; maybe there is also a solution.
I have the same problem with Motorola HF-850 car kit. I'm about to downgrade too. This sux.
Same issue here with Nissan Sentra 2008.
I can dial and receive calls but the audio works about 30% or the time. It is hit or miss.
Same here in a 2007 UK CITROËN C4 (5 door hatchback) with factory fitted Bluetooth car kit, using an Orange M3100 with the Schap's WM6 Pro 3.60a ROM. Looks like I'm going back to the Orange WM5 ROM as this is a deal breaker for me. Very disappointing.
try this
I had similair problems a few pretty good solutions:
-jetware search google i use this one
-Solution:2
Change the COD (Class of Device) from a PDA device to a smartphone device.
This can be done this way:
1. First make sure you've got a backup, or remember all settings you change in the registry.
2. Edit with a registry editor the following key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Bluetooth\SYS\COD
By default my vario II does have the value: 1048852 (decimal)
Change this to: 5374476 (decimal).
3. Soft restart your device
4. Voila! Your device now identifies itself as a smartphone
see this thread
http://forum.xda-developers.com/showthread.php?t=290871
Thanks!
I tried the Jetware solution: no luck.
I also tried the COD trick: very strange result, I was able to make just 1 (one) call and other calls were again not possible (no sound).
Maybe there is a solution in updating the software of the handsfree set in the car. I will ask my Citroen agent to do this, if possible.
I will post the results.
I haven't tried the COD trick, but I don't think this will work. It's not a case of my car 'ignoring' my M3100... it pairs OK, and the car's display shows an incoming call, allows me to pick it up, etc, but no sound comes out of the speakers and the other party doesn't hear my voice. It's like the car is receiving the data stream to tell it what's happening on the call, but not the sound.
I don't have any of these problems with WM5, I don't even need to use the JetWare solution.
same problem with Peugeot 407
Same problem here with Peugeot 407
What I found is that if I start a call without Bluetooth and start Bluetooth during the caal, the sound works perfectly. Every next call has the same problem as before though.
TyTN; WM6 Schap's 3.60a;Radio 1.47.00.10
Hi.
I am with Motorola's HF-850 car kit and I get the sound only after 8-10 full seconds from answering. It is so sad that I have to say "wait....wait" every time I answer a call....
There is a post on this forum that suggests someones got it working with an Audi and the latest Black beta rom...
http://www.4winmobile.com/forums/hermes-black-rom-support/11291-black-x-beta-2-smash-trash-11.html
Anyone tried this?
This post also suggests that the newest Black roms may have fixed the issue
http://htc-devs.com/forum/index.php?topic=42.msg321;topicseen
Here's hoping!
That will not work on the Artemis
But I tried several WM6 roms, including the Black & Blue 4.1: no luck.
Looks like a real WM6 issue, as it's happening with several phone models.
UPDATE: No software update for the factory Citroen bluetooth handsfree according to the local dealer; so that's no solution
I have tried 5 of the latest roms yesterday including all the fixed mentioned in this forum. The best I got was with Sleuth rom where I get audio about 50% of the time. Answering with that rom results in a 5 seconds delay before audio connects causing me to yell "wait, wait, I am here ... "
I even tried a blootooth stack from Broadcomm but the result was not better.
Out of desperation as I bought this car specially for its built in bluetooth kit, I downgraded to Cingular Mobile 5 Rom version (2.15.502.3)
I am surprised and kind of thrilled to report that my 8525 and the car kit are working perfectly together and reliably.
There must be either a bug or a setting/configuration issue on the Mobile 6 bluetooth stack that caused this issue. I am unfortunately back to mobile 5 for the time being until this issue is resolved.
SPV m3100, CK3100 AND WM6
I have an Orange SPV M3100 in Spain with WM6 and i have the same problem. With WM5 and Jetware estension, i had to pair parrot and pda manually every time i got into my car, because they did not connect automatically (Blueetoth-->Devices-->Parrot CK3100-->FreeHand-->OK), but then it works well and i could receive and make phone calls.
But since I upgrade to WM6 i have to pair it manuaaly too, they connect, but it only works from time to time; most times, if i make a call it dials but i cannot speak and people does not hear me; if there is an incoming call, I see the number in the displsy but i can receive it.
Anybody with WM6 and Parrot Ck3100 works well?
I have the same problem with a Mio C520 SatNav. Its bluetooth handsfree works fine with WM5 but not WM6.
I also posted this on a thread on bluetooth headsets, http://forum.xda-developers.com/showthread.php?t=301636&page=6
I tried many different versions. So far with Sleuth's WM6, I had sound around 50% of the time. Similar to one of the previous posters.
Until there is a fix I will have to go back to WM5
I use a parrot car kit and it works fine. However, I noticed some new functionality on my lcd, like displaying battery and signal levels which was not available with the original WM5. That was available only with specific phones. Based on that I believe that a firmware update of your car kit could solve the problem. The issue is whether this is provided for you and if you will have to pay. Parrot offers them for free and you can upgrade via BT.
Hi all, First of all I'd like to say this is the most informative forum I have been involved with . Up till now I haven't needed to post any questions.
Now....
I have an i-mate Jasjam herm200 (purchaced from Telstra). Until recently I was running WM5 which it was shipped with. Apart from the slow speed of the PPC (due in part to the Telstra Bloatware) it ran fine.
Since then I have tried many cooked ROMS inc. all Jasjamming's WM black editions, Most of Schaps WM6 and a few others, and I'm having problems with connecting my HS850 headset & my Altina GBT709 GPS receiver.
The Headset,
After pairing the headset I found that when making or receiving a call the person on the other end can only hear me for a few seconds but I don't hear anything, then when the headset Icon appears on the screen the call remains active but I can't hear the other person & they can't hear me.
I reflashed the Telstra Jasjam shipped WM5 rom: 1.31.305.2_106_6275_1.38.30.10_108_ship and the headset stilled didn't work , reflashed it with the same rom again (various WM6 roms in between) and it will work fine.
Can someone tell me if the problem is with the HS850 or the WM6 upgrade?
The GPS,
Since I have started flashing different roms I have never been able to connect the Altina 709 to TomTom Navigator 6, even when reflashed with the shipped rom. I cannot figure out if the problem is with the Bluetoth or a configuration issue with my PPC.
I can live without the GPS as I have a stand alone TT GO 500, but not being able to connect the bluetooth headset properly is driving me NUTS!!!
Please Please Please can someone help me figure this out.
Squirt
Any ideas people?
Don't know if this helps,but I found the Telstra customisations that you can install give me grief with my parrot car bluetooth system - they mess with the bluetooth stack in some way. I found the Telstra WM5 rom didn't play nicely either, which was my main incentive to upgrade to WM6. Are you using a clean install of the WM6 roms without tacking any of the telstra stuff on top?
I eventually found a .cab with just the proxy manager which is all I needed, and schap's roms work nicely for me regarding bluetooth, so I'm a bit wary of fiddling with it now.... I know the black series (and a few others that must have used the same build) had bluetooth issues for me.
Thanks for your reply, I'm currently running Black 3.0.1 which has been the closest I've got to getting the BT H/Free working.
With 3.0.1 I can hear the person on the other end through the phone speaker not the BT, BUT, They can hear me through the BT headset........strange.
I'm just waiting to catch up with a bloke from work with a different brand BT Headset to see if it makes a difference.