Some Problem in Display!? - JASJAR, XDA Exec, MDA Pro Software Upgrading

I had repaired my hinge once, afterthat, I installed the new i-mate ROM. The display become strange since then... It is the most strange when displaying pictures. It looks like the entire picture has been digitally modified by color blur?! (I'm not sure how to discribe it) It just like a lot of areas is rendered by the same color (the source picture has far more complicated details, but it is all been cut) And it is not a 3rd party software problem...
I assure my-self that this is not the ROM problem, I installed the old O2 ROM, and the problem still exist....
So can u guys please give me some advices?
Shall I send it back to repair? Could a hinge repair done that damage?

einsteinck said:
Shall I send it back to repair? Could a hinge repair done that damage?
Click to expand...
Click to collapse
Check the connectors have not come loose first, then check the cable in the hinge. What did you do to repair the hinge?
Richard

I did not repair the hinge by my-self. I send it to Lemel repair station. And I don't know how to check the hinge or the cable on my own...
What I want to know is: Is this a hardware problem or a software one...

The set of cables if broken, cannot be re soldered or repaired...u will have to go in for a new set of cables and that is quite dearer around 15-200 USD

hdubli said:
The set of cables if broken, cannot be re soldered or repaired...u will have to go in for a new set of cables and that is quite dearer around 15-200 USD
Click to expand...
Click to collapse
That's a lot for a cable :shock: . I have repaired a jasjar that had sheared using an m5000's intact cable to map out a circuit plan of all the pins. I'll upload a diagram when I find it again.
Richard

Screen Cable needed
Hi there
can u pls tell me where did u get the cable from, i have the same problem and i want that part so i fix my phone.
lookign forward to hearing from u and thx in advance
Regards

Related

WARNING: Do not break your Sync-Connector

:shock:
The connector for active-sync of the XDA is very badly constructed.
Until I got my new XDA2, I had a XDA1. I had it exchanged (warranty) against the XDA2
after some discussion with o2 about bad quality ot the xda1 (I had it 3 times repaired, but it broke soon again. Last problem: the connector for syncing broke 3 days after I got the replacement xda.)
The problem seems to be the smal plastic lid that holds the contacts:
While the plug resting on the plastic lid and the metal frame not supporting the plug suffiiciently because of a quite big gap between them, the lid could easily break if force
is applied up- or downward.
This way my last replacement XDA1 deterioated.
(Un-)Fortunately, the active-sync+charge cable (non O2-accessory) I had for XDA1 my seems to be pin compatible (syncing works).
So the plug is the same, and one should be VERY careful with it.
->Also the original charging adapter is constructed in a way to send bending forces to
the small plastic lid of the inner connector (good to know for warranty discussions).
I actually think of a plug-adaptor, that interfaces between the original plug and the outer
world. It cold be supported via a steelframe that one integrates into the original wallet.
Ideas are welcome!
Summary for the lazy:
---------------
! The Active-Sync-Plug is *badly* constructed.
- The inner plastic lid holding the connectors BREAKS easily.
---------------------------------------
!! So beware of cables attached to the sync connector. !!
---------------------------------------
Use only the craddle that applies forces only to the case of the XDA
:!:
May I add on top of this ... it happened to me and the USB connector is broken. The bad news is: there is NO way yo fix it and as it's integrated with the main board (the power pin) the only option is to replace the main board :x :evil:
Guys, be more than just careful with your devices on that point.
Biso007 said:
May I add on top of this ... it happened to me and the USB connector is broken. The bad news is: there is NO way yo fix it and as it's integrated with the main board (the power pin) the only option is to replace the main board :x :evil:
Guys, be more than just careful with your devices on that point.
Click to expand...
Click to collapse
This is not necessarily true. We have the sync and audiojack connectors in stock and can replace them. They are a pain, but doable.
May be you are right, but it's the case with my device. They said the connection point with the power track (pin) is lost, so the main board has to be replaced. Or maybe they are not equipped the same way you have at USA, and the shipping cost makes it more expensive
In Australia the O2 service Centre will charge you for a compleate replacment main board, they say they can't fix the connector and because the phone was out of warranty they simply charge for a compleatly new board :x SHARKS!
XDA Connector repairs avaliable here
Hi Guys,
I used a company in the UK to repair by busted XDA 2. The damn connector fell out when using an aftermarket in car charger. Got his company to repair it. Were pretty good. their web site adress is www.apexlaptops.co.uk
I was pleased wit the service. Hope they can help you like they helped me!
Good luck guys.
Pocket PC Techs ROCK
I had my unit connected to a cable and landed on the floor - connector first. OUCH. The female connector on the bottom of the unit was loose - and the unit became useless (connections no longer worked). I sent it to Pocket PC Techs, and they fixed and returned it all within a week, and for a very reasonable fee as well. Try them. It'll probably work. Just be gentle with it when it's plugged in.
p n
Re: SYNC CONNECTOR REPAIRS
brentwebster said:
Hi guys. Just to let you all know that i do repairs on sync connectors if anyone has got a broken one. The repairs are done same day sevice, so the day i recieve the phone i repair it and send it back out to you the same day. Th cost of this repair is £40-00. My contact detials are [email protected]. Email me for further details
Click to expand...
Click to collapse
Hi Guys, just to let you know that brentwebster has used the picture from my auction and I sell the connectors for £10 on ebay, if you are fairly good with a soldering iron you can do it yourself - I'll give a discount and free postage in the UK to members of XDA-developers who mail me before buying for details
Richard / fluffcat1
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=9707299579
o p
Re: SYNC CONNECTOR REPAIRS
brentwebster said:
I can supply these connectors at £8 to anyone that wants them. :wink:
Click to expand...
Click to collapse
PM me for a better price :twisted:
Richard
Re: SYNC CONNECTOR REPAIRS
Another person offering this service to those who can't do it themselves:
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=9704914642
£39.99 plus return postage, paypal accepted, 647 feedback rating ( 1000 under mne but there we go ) , no affiliation blah blah blah. Maybe brentwebster can start a price war with them as well?....
Richard
Broken SYNC Connector on my XDA IIi
Can anyone repair this????
If they can please email me with details (address, cost etc)
My email is [email protected]
Thankx
I have one with the connector completely off. Rather soldering a new one on, I was thinking of hard wiring a usb lead on, to fit my arkon gps receiver. Does anyone know the pin outs. I only need data in/out, ground and vcc

UNIVERSAL : need a Coaxial Cable Pre-assy replacement

Hello
I am new on this forum, sorry if this type of question has alreday been answered.
I've got a UNIVERSAL/ SPV M500 and the Coaxial Cable (linking the screen and the keyboard) has been twisted and is damaged.
Where can I find/buy a spare part to replace it ? the reference number is 73H00233-01M (Coaxial Cable Pre-assembly) as indicated in the service manual.
Thank for your help.
Hey,
If you find it let me know, I need one two. Actually these are two cables the Coaxial (Display) and Coaxial (Functional). My screen goes white in landscape mode and I confirmed it's the cable by disassembling my machine. However was unable to find that cable Will let you know if I find it.
Me too.
I am getting odd touch screen errors and think it can only be the cable.
If anyone knows of a supplier, please post here.
Has anyone tried contacting HTC directly?
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
villard said:
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
Click to expand...
Click to collapse
Thanks,
Please do let me know, I really need that cable.
MOBILER
Finally ... got cables !
Here mate ... take this adress
http://qinyieproduct.diytrade.com/sdp/444314/4/pd-2468984/2411741-0.html
villard said:
Hello
I am new on this forum, sorry if this type of question has alreday been answered.
I've got a UNIVERSAL/ SPV M500 and the Coaxial Cable (linking the screen and the keyboard) has been twisted and is damaged.
Where can I find/buy a spare part to replace it ? the reference number is 73H00233-01M (Coaxial Cable Pre-assembly) as indicated in the service manual.
Thank for your help.
Click to expand...
Click to collapse
found coaxial cable for £60 plus vat.
villard said:
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
Click to expand...
Click to collapse
Give this site a look, http://www.apexlaptops.co.uk/Universal.htm
I have been having the same problems as you guys. my uni have been getting "white screen of death" for about 6 months now.
I am going to take out the cable and try and fix it myself. (fingers crossed)
I will let you all know how it goes. I felt £60 plus vat and postage was a bit steep.
coax cable
Fixed it!!
I took apart my uni down to the last screw, and rebuilt it.
In the process I did find that i am missing an antenna in the back, it should have 3 but only has 2. oh well it works.
The 3rd antenna is for 3g and i am not on 3.
Anyway back to my uni.
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
If this works for longer than a month then i will solder the cable down.
Touch wood it seems to be working. I will try and get some photos done tonight
gingerchristopher.
Hi,
Congratulations!
What tools did you use for this job(srews, tweezers)?
gingerchristopher said:
Fixed it!!
I took apart my uni down to the last screw, and rebuilt it.
In the process I did find that i am missing an antenna in the back, it should have 3 but only has 2. oh well it works.
The 3rd antenna is for 3g and i am not on 3.
Anyway back to my uni.
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
If this works for longer than a month then i will solder the cable down.
Touch wood it seems to be working. I will try and get some photos done tonight
gingerchristopher.
Click to expand...
Click to collapse
re: fixed it
Yes just a torex screwdriver size 6 to take out the 4 security screws in the battery tray, watch makers screwdrivers and a pair of fine point tweezers.
still having problems with my camera so photos will follow when i take it apart to solder.
ang how about antistatic gloves?
gingerchristopher said:
Yes just a torex screwdriver size 6 to take out the 4 security screws in the battery tray, watch makers screwdrivers and a pair of fine point tweezers.
still having problems with my camera so photos will follow when i take it apart to solder.
Click to expand...
Click to collapse
Anti Static gloves!!
Because of the Job I do, I have an earthing band to connect the phone and me to the wall, and put the phone on an anti static table cover. All is good so far. I am looking at Feb to solder (as i have some leave in). There will be detailed photos and description.
Untill then........
Just found a coax on e-bay
Hi I hope anyone who is after this coax cable can read this before the weekend is out, as there is one on e-bay for £40 this is the link.
http://cgi.ebay.co.uk/NEW-O2-XDA-EX...9QQihZ020QQcategoryZ41343QQrdZ1QQcmdZViewItem
Chris.
Good done man go ahaed, and plz try to post the photos.
Another question, my universal some times lost its external speaker sound, so i cannot hear the rings, when i press on the back of the device, exactly on the battery cover in the middle between the two dummy holes and the usb port, it works again. Do u think that this is due to the coaxial damage also, even i don'y have any problem in the screen??
hbahaie said:
Good done man go ahaed, and plz try to post the photos.
Another question, my universal some times lost its external speaker sound, so i cannot hear the rings, when i press on the back of the device, exactly on the battery cover in the middle between the two dummy holes and the usb port, it works again. Do u think that this is due to the coaxial damage also, even i don'y have any problem in the screen??
Click to expand...
Click to collapse
nope. open up and check the contacts
omega_ said:
nope. open up and check the contacts
Click to expand...
Click to collapse
Thank you very much for your advice, I'll check. Thanks
hbahaie said:
Thank you very much for your advice, I'll check. Thanks
Click to expand...
Click to collapse
I have disassembled my uni and checked for all connections, but there was no improvement. I can confirm that the disappearance of external speakers sound is not due to co-axial cable. The proof is that i extracted my main borad from my uni and implanted it in another one, i assumed that the problem will be rsolved, but the same problem still exists. Ok, now i can disassemble my uni for smallest piece, but any one advise me where is th connection part or the piece that causes that problem. Again a brief description of the problem:
when there is a coming call, i cannot here the ring or it is sevrely intermitent, also when i play any WMP file, i cannot here the sound, if I press firmly on the base or around the keyboard the sound comes again and may last for a few minutes or disappear after another press. So, there is a lose part in the main board i think that needs fixation, but which one????
Hi all
Now it takes me more than a month to upgrade my JASJAR due to a lot of problems I faced during this upgrading adventure… anyway, the last problem I still have is that after upgrading the screen goes crazy, I mean if you press on the screen the colours are mixed for few seconds and then its ok but at any time I touch the screen again the same happened so you can imagine what if I am going to dial a number or write a message …. So can anyone advice me what to do? …
The rom version is 1.13.82
Radio 1.04.02
Extrom 1.13.188
And I think the bootloader 1.00 and I don’t know why I feel that the bootloader is the reason ... I made a deep search but I couldn’t find problem like mine
gingerchristopher said:
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
Click to expand...
Click to collapse
Sitting next to my M5000 and all of a sudden the screen turned on but was white!
Following your lead I found that the first i.e. 'underneath' connector was not fully home. A little push and all is well.
Took the time to pack out the housing for the stylus to stop the little blighter escaping whilst in there.
Thank you for taking the time to post gingerchristopher.
Pete

my screen become white...

why my screen become white, didnt hav any image, oli white..... But the program and rom still on!!! Can somebody help me? My one is Softbank X01HT
have a look thru this thread in the "HERMES" forum.....
http://forum.xda-developers.com/showthread.php?t=321163
...they're doing some pretty thorough **** over there to resolve this issue!!!
thong123456 said:
why my screen become white, didnt hav any image, oli white..... But the program and rom still on!!! Can somebody help me? My one is Softbank X01HT
Click to expand...
Click to collapse
Do you have made a ROM upgrade?
its your flexible.. the one who connect lcd to the motherboard of your hermes.. i had the very same problem 3 months ago. and i bought it the flexible on ebay for $50..
I had the same problem. If i push the ON/OFF button twicce, one for turn off the PDA and one to turn it on again, i can see the display OK. Orange has changed me the PDA.
Flex Cable Connector
It is the flex cable connector that goes bad. You can get a new flex cable as mentioned before on ebay (I've seen for $35)... or you can try the other fix mentioned on the link in the first reply: disassemble the phone, put a small peice of foam (similar to memory foam) over the flex cable connector, and reassemble the phone. This worked for me. It holds the connector in tighter and the screen whiteout quit. You will need a T-6 screw driver.
RanDomIze said:
Do you have made a ROM upgrade?
Click to expand...
Click to collapse
I have the same problem after upgrade the rom....!
solution????

[Q] Replaced LCD twice, only backlight comes on... What to do, now!?

Hey Boys n Girls!
I made a mistake and bought off eBay a phone with a "not working LCD":
" This is a used HTC Desire Z smartphone. The item was dropped on water and immediately pulled out. The LCD screen doesn't work anymore as some cable inside is cracked. Everything works fine, touchscreen, menu and the device boots fine, you can hear the sound etc but no image. Anyone can fix this if you have an LCD spare for HTC Desire Z and the phone can be used and works fine, just the LCD needs replacing. Comes with original box, manuals and battery but no charger or data cable. I want to sell this fast so Happy Bidding!"
, also ordered already from two different seller LCD replacement screens neither of them worked. Backlight works on both but nothing else. Im quite puzzled what to do next...
Anyone got any idea?
Please let me know! THanks in advance!
Sounds like some cable is not working, rather than the two screens you've purchased! There is a guide somewhere here for all of that stuff. Best of luck mate!
captainreynolds said:
Sounds like some cable is not working, rather than the two screens you've purchased! There is a guide somewhere here for all of that stuff. Best of luck mate!
Click to expand...
Click to collapse
If you could kindly link that guide, it would be very much appreciated! Thanks!
try searching for ribbon cable. You should prob just take it to a cell phone store. Phone geeks in San Marcos did my repair for 70. I was texting gf while playing golf in pouring rain.
Sent from my SGH-T989 using xda premium
Here is the link to the teardown guide: http://forum.xda-developers.com/showthread.php?t=863919
The flex ribbon cables are not that expensive. If you were comfortable replacing the screen, I would say you have the ability to replace the flex ribbon cable without a problem.
beefynick said:
If you were comfortable replacing the screen, I would say you have the ability to replace the flex ribbon cable without a problem.
Click to expand...
Click to collapse
Im going to order it tonight and give an update as soon as I got the flex ribbon cable.... I assembled and disassembled so many times already soon will be able to do it blindfolded
Also while you have it apart clean the logic board with denatured or pure alcohol and a soft bristled brush. Let it dry completely! That way it won't corrode further from the water damage!
killj0y said:
Also while you have it apart clean the logic board with denatured or pure alcohol and a soft bristled brush. Let it dry completely! That way it won't corrode further from the water damage!
Click to expand...
Click to collapse
I will do that since it will probably take like 2 weeks to ship the flex ribbon from China Thanks Man!
modzsi said:
I will do that since it will probably take like 2 weeks to ship the flex ribbon from China Thanks Man!
Click to expand...
Click to collapse
No prob cheap insurance plus it could even since a current or future problem I do this work for people can you tell lol. Denatured is best otherwise I think 97 is as pure as you'll find. Most stores carry the latter.
Ps be gentle no need to go medieval on it
Replacing the Flex Ribbon Cable solved my problems.... Cheers Everyone!

Disassemble and reassemble of galaxy nexus :)

I have a few pictures of my galaxy nexus broken down if anyone would like to ask me questions on how and where things go they can. I actually find this phone to be very easy to get apart and if careful can be reassembled in 15 minutes. I was actually replacing my speaker with some old parts I bought off a guy. No more crackling! Anyways in the process grabbed some pics
U can see the first three are the screen bottom speaker, main board, vibe, etc. The last pic she's all back together
Sent from my Galaxy Nexus using xda premium
Somehow I imagined a picture of me tearing down a smartphone where I was photoshopped out and replaced with a picture of a dog in a labcoat saying: "I have no idea what I'm doing"
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
IINexusII said:
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
Click to expand...
Click to collapse
is the imei sticker that is attached onto the black plastic removable from the main board?
IINexusII said:
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
Click to expand...
Click to collapse
Yes sir....I just stuck a razor blade between them and the housing and they come right off connected to a gel like glue. This was good because sticking them back in place they actually stayed. U also have to remove the vibrator motor and the long black wire running down alongside the battery compartment (it has connectors on each end) then of course your two ribbon connectors for main board then one ribbon connector for bottom speaker. Didn't touch cams no need to.....very very easy job in fact it was to easy.
I have to replace my USB board (my USB port was damaged) and I am a newbie doing this kind of service myself. I bought it on ebay:
http://www.ebay.com/itm/OEM-Charger...ltDomain_0&hash=item35bc2f9280#ht_3392wt_1052
Do you think it is possible for someone with no experience to make it? I think I will try it myself, not in the mood to send it to some repair shop and wait 30 days..
juliano_q said:
I have to replace my USB board (my USB port was damaged) and I am a newbie doing this kind of service myself. I bought it on ebay:
http://www.ebay.com/itm/OEM-Charger...ltDomain_0&hash=item35bc2f9280#ht_3392wt_1052
Do you think it is possible for someone with no experience to make it? I think I will try it myself, not in the mood to send it to some repair shop and wait 30 days..
Click to expand...
Click to collapse
Yes for sure...but if u do not feel safe doing it then take it in. I know to get to the usb the whole speaker and housing comes off of the top of that. Which is one screw then a ribbon fairly easy....then u just work something thin in between that and housing like a guitar pic or Mac card. I would go with guitar pic tho so u don't mess the corners of your card up. I know that once the speaker portion is off u see in my first pic the USB I think has its on board. I truthfully did not take that portion of it out thought it was kind of pointless. If u need help I will assist u if u decide to do it yourself
sarni84 said:
Yes for sure...but if u do not feel safe doing it then take it in. I know to get to the usb the whole speaker and housing comes off of the top of that. Which is one screw then a ribbon fairly easy....then u just work something thin in between that and housing like a guitar pic or Mac card. I would go with guitar pic tho so u don't mess the corners of your card up. I know that once the speaker portion is off u see in my first pic the USB I think has its on board. I truthfully did not take that portion of it out thought it was kind of pointless. If u need help I will assist u if u decide to do it yourself
Click to expand...
Click to collapse
Thanks, I think I will try it myself, just have to wait for it to arrive.
juliano_q said:
Thanks, I think I will try it myself, just have to wait for it to arrive.
Click to expand...
Click to collapse
Yea dude pm me and I'll definitely help out
Thats pretty neat man, do you know where the GPS chip is?
I replaced my back cover and apparently I damaged the GPS chip cause I have NO gps lock, software side its ruled out (I flashed many diff ROMS, kernels and Radios and it used to work well before I opened up my Gnex)
Thank you.
where is the VZ LTE radio? maybe i can swap mine out for one that doesnt cause signal drops.
Sergio PC said:
Thats pretty neat man, do you know where the GPS chip is?
I replaced my back cover and apparently I damaged the GPS chip cause I have NO gps lock, software side its ruled out (I flashed many diff ROMS, kernels and Radios and it used to work well before I opened up my Gnex)
Thank you.
Click to expand...
Click to collapse
The battery cover? Hmmmm. I am pretty sure the GPS chip is on the opposite side of motherboard. Looking at ifixit photos it says right by rear camera on the opposite side of motherboard.
Edit...also if u look at first pic in my pictures look on right side of battery compartment . See the black wire with the connectors on each end? I wonder if the connector closest to bottom came loose or has something to do with it
10roller said:
where is the VZ LTE radio? maybe i can swap mine out for one that doesnt cause signal drops.
Click to expand...
Click to collapse
Not sure I have GSM model. And dude good luck with that unless u know how to solder chips on to motherboards that is nearly impossible and I think swapping a lte chip for another lte chip won't solve your problem
sarni84 said:
The battery cover? Hmmmm. I am pretty sure the GPS chip is on the opposite side of motherboard. Looking at ifixit photos it says right by rear camera on the opposite side of motherboard.
Edit...also if u look at first pic in my pictures look on right side of battery compartment . See the black wire with the connectors on each end? I wonder if the connector closest to bottom came loose or has something to do with it
Click to expand...
Click to collapse
Thanks, appreciate your time.
I checked out ifixit, thinking that in the process of removing the cover I could of hit the GPS chip or something, but since you pointed out that its on the opposite side of the motherboard that's not a possibility. Since I have not removed the mother board.
I have not opened it again, afraid of ruining something else.
But I guess I will have to in order to check the wire you speak about.
Salutations
I sent my phone in for repair to Samsung via Expansys for a bad external speaker. Back when it went bad, phone was too new to have all parts available as spares on the net plus the phone was still under warranty so I send it back to Samsung via Expansys-usa. But what I think happened is that Expansys didn't send it to Samsung and repaired it inhouse. I can say that because all screws inside the phone had chewed up heads and the repair didn't look good however the external speaker was working. First thing I found out that external volume rocker was not working anymore. So I send it back again to Expansys and I just received it back today with a note saying that the volume rocker ribbon pins have come away from the main board and taken the pin with them.
Bottom line is that they didn't repair the phone. Any ideas on how I can get this fixed? Do I have to change the ribbon? if I want to do it myself or this sort of damage requires a new board?
Any ideas comments are appreciated.
Edit: Link to photo showing the pins that are separated from the board
sarni84 said:
I have a few pictures of my galaxy nexus broken down if anyone would like to ask me questions on how and where things go they can. I actually find this phone to be very easy to get apart and if careful can be reassembled in 15 minutes. I was actually replacing my speaker with some old parts I bought off a guy. No more crackling! Anyways in the process grabbed some pics
U can see the first three are the screen bottom speaker, main board, vibe, etc. The last pic she's all back together
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Hi Sarni,
I accidentally snapped the ribbon (refer to attached pic, circled in red), and now my speaker is not working anymore. I guess that ribbon was for connecting the speaker and headphone jack? . What do you think i should do now, replace the whole piece?
I also intend to replace my damaged charge port, but not sure how to proceed for that.
Thanks,
Dennis

Categories

Resources