Related
My Uni got stucked at splash screen i.e the blue O2 screen (not bootloader).
The story was like this:
Just before it happened, I was trying to enter the bootloader to flash my ROM, i dont know how i did it but somehow there was some charactors on my screen, some settings.. My curiousity lead me to play around with the settings, I couldnt remember what did i do, I just press the up and down button and the settings changed. Feeling bad that it might ruin my precious Uni, I quickly soft reset it. And then BOOM! I cant start it anymore. It just stucked at the blue O2 splash screen.
Pls pls anyone know how to get back to the setting screen again? I guess it was some button combination to get into that screen. Does anyone know what is the combination?
try this tools
instructions:
-disconnect USB cable
-disable USB connection in desktop ActiveSync
-connect USB cable
-start mtty
-create new connection and select USB from ports
press enter to see USB prompt in mtty:
USB>
type (dont copy&paste):
task 28
and press enter
If the result is the following then you are out of luck:
flFormatPhysicalDrive:status=23
DOC_format failed!
cheers
indra9110
indra9110 said:
try this tools
If the result is the following then you are out of luck:
flFormatPhysicalDrive:status=23
DOC_format failed!
Click to expand...
Click to collapse
It says exactly like that! Can anyone help?
try hard resetting ur phone.
keep the two minus buttons pressed and they with the pen click the reset button.
friend, hard reseting, flashing, mtty, took off battery, i've done all that.. nothing works.
satanisme said:
friend, hard reseting, flashing, mtty, took off battery, i've done all that.. nothing works.
Click to expand...
Click to collapse
Forget it. You have a defective internal flashdisk. The only option is to return it to the vendor/manufacturer and have it repaired under warranty.
believe Wiz words, because i had the same problem !!TWO!! times in three months.
next time i will smash the Uni against a wall
Shoot! 2 times in 3 months? What did you do dude?
I'm so sad coz I'm currently in Malaysia and the unit is from UK. I asked the O2 service center over here and they said they dont have the jurisdiction to repair it. Even opening up the Uni will temper the warranty. What a bull! Now I have to find a way to send my Uni to UK quick since the warranty is gonna void in 2 months time.
Hello,
I'm stuck at the screen, DOPOD ENJOY MOBILITY,
R 1.1100
G 42.45.P8
D 1.30.111.WWE
when run the mtty, ask for com port, not USB able to be selected.
regards, yan
possible solution
Hi guys,
There is a tip from Dubli for those who stuck on splash screen:
1. Get mtty
2. Connect to USB, press enter
3. Type task 32, enter
4. Type 28, enter
5. Flash CE Rom only
6. Hard Reset
Make sure to type task 32 first before task 28 coz task 28 alone wont work.
Pls try this and tell me the outcome. I cant try this coz i just sent my uni to UK just now.
Stuck on Splash screen ..please help urgent
hi guys,
I have a Xda Exec phone
I'm stuck at the screen,
R 1.09.00
G 42.42.P8
D 1.30.107.WWE
I have tried using the procedure
1. Get mtty
2. Connect to USB, press enter
3. Type task 32, enter
4. Type 28, enter
5. Flash CE Rom only (here is where i am stuck ? what does it mean to flash rom ?)
6. Hard Reset
What do i do ? Please help
Hello,
my universal screen is stuck
after Ivan's (3.5)rom upgrade
i pressed the 2 softkeys and reset button
i got the press 0 to clear memory
I press 0 and then the universal does not start up
plz plz plz help me
I was trying to understand what is mtty tool but never understood
some kind person plz help...
thankyou (anxiously waiting for reply)
corleno said:
Hello,
my universal screen is stuck
after Ivan's (3.5)rom upgrade
i pressed the 2 softkeys and reset button
i got the press 0 to clear memory
I press 0 and then the universal does not start up
plz plz plz help me
I was trying to understand what is mtty tool but never understood
some kind person plz help...
thankyou (anxiously waiting for reply)
Click to expand...
Click to collapse
Iv managed to get into bootloader
I run mtty
my only problem is I have COM1 and COM2 in dropdown
no USB
can some 1 tell me why ??
please
corleno said:
Iv managed to get into bootloader
I run mtty
my only problem is I have COM1 and COM2 in dropdown
no USB
can some 1 tell me why ??
please
Click to expand...
Click to collapse
When it Bootloader mode, there are some words on screen, check if it is minimum v1.00 and above.
When in Bootloader mode, activesync is off, but you can run the upgrade software.
CWKJ said:
When it Bootloader mode, there are some words on screen, check if it is minimum v1.00 and above.
When in Bootloader mode, activesync is off, but you can run the upgrade software.
Click to expand...
Click to collapse
thank you for ur reply
it says v 1.00
activ sync is off
but I donno how 2 set up mtty
because I have only com1 and com2
no USB
i guess i need to get USB>
on screen whn i press enter
but i dont get anything
I tried rom upgrade,
the system says device not recognizable
Hope you did not change or delete any previous settings on both PPC & PC.
Just connect your device to your usual working activesync usb port.
Do not use ROMUpgradeUt.exe, use MaUpgradeUt_noID.exe to upgrade from Bootloader mode.
CWKJ said:
Hope you did not change or delete any previous settings on both PPC & PC.
Just connect your device to your usual working activesync usb port.
Do not use ROMUpgradeUt.exe, use MaUpgradeUt_noID.exe to upgrade from Bootloader mode.
Click to expand...
Click to collapse
yes I finally managed to enable USB
and I use
USB>set 14 0
then I get this
HTCST ÚÈÒHTCEUSB>
I try normal upgrade with ROMUpgradeUt got error 101
now I try with MaUpgradeUt_noID.exe after replacing the 3 files from the country_error folder
I get error saying the upgrade is not designed to run on my device
CWKJ said:
Hope you did not change or delete any previous settings on both PPC & PC.
Just connect your device to your usual working activesync usb port.
Do not use ROMUpgradeUt.exe, use MaUpgradeUt_noID.exe to upgrade from Bootloader mode.
Click to expand...
Click to collapse
Thank you CWKJ
Iv got the system to work again
thanks
I re-flashed with my old O2 rom and no mitty required
just boot loader
You are welcome. Hope it is of any help.
I have the same problem!
But after have this problem, I log in to bootloader and up rom beta 15 again (old rom), after up rom beta 15 finished and everything is ok! I start re up rom (3.5) for again and everything is good! now, i'm running 3.5, it's very very good, faster, bigger memory...! Thanks to Mr.Ivan so much!
quanss78 said:
But after have this problem, I log in to bootloader and up rom beta 15 again (old rom), after up rom beta 15 finished and everything is ok! I start re up rom (3.5) for again and everything is good! now, i'm running 3.5, it's very very good, faster, bigger memory...! Thanks to Mr.Ivan so much!
Click to expand...
Click to collapse
Uv got some bal*s dude
Iv shi* my pants the very 1st time
Im too scared 2 go back..or is it front
PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
dopod900xxx said:
PLEASE HELP!!!
I try upgrade my Dopod 900 to WM6 by using http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip, but after the upgrade success 100%, i disconnect the USB, and hard reset the PDA, then the PDA cannot bootup, it alwaus showing the black screen...
When i try hard reset again, i can see the display show option 0 to reset and option X to exit, but try both keys which back to the same black screen...
I also try press power+light+reset, but no responses at all... when i plug in the power cord, the light for charging not on as well...
PLS HELP....
Click to expand...
Click to collapse
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
From my past experience you have to flash to the original manufacturer rom first. Then you flash to whatever rom you want.
hope this helps
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
dopod900xxx said:
Thanks all, I'm now be able to re-flash the ROM and upgraded to WM6....
Here comes another issue... after i run the first setup and reset the PDA, it stuck on the Windows Mobile screen, any clue?
thanks again.
Click to expand...
Click to collapse
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
nvatvani said:
From the file link you have specified, http://micmeo.com/UNI/WM6/900_WWE_20...0_wwe_ship.zip it seems that you are using Jwrightmcps' WM6 2.01.08 WWE Rom Release.
I too have lock-up problems but only during boot-up. The frequency of this happenning is about 30% and why it happens is still unknown since the lock-up happens at random stages during the booting sequence. The only solution that I know of for now is to simply do a soft-reset repeatedly until the device boots up properly.
Click to expand...
Click to collapse
This appears to be a common problem as seen from different posts. Thankfully things are ok after reset.
yes, after reset few times, it works... and everytime it hangs, need reset few times...
dopod900xxx said:
yes, after reset few times, it works... and everytime it hangs, need reset few times...
Click to expand...
Click to collapse
You might find this of interest - it refers to the problem of hanging after soft reset in the 2.01.08 WWE Rom:
jmallen said:
I had this problem also. I found pulling out the battery for 5 or more seconds solved this for me every time.
Give it a try. Good luck
Click to expand...
Click to collapse
It may be solved in later versions.
d_ranade said:
Try to enter the bootloader mode (power+light+reset). From what you have described it appears that you should not have problem entering the bootloader mode. Please remember that in bootloader mode yor screen is dark and only when you look very carefully you will be able to read the word "Serial" on the top of the screen and bootloader version number at the bottom. If there is inssuficient illumination in the room it is quite possible to think that the screen is blank. There will be no backlight. Once you are in the bootloader connect to your PC (before connecting please open Active sync on your PC uncheck the "Allow USB" connection in File / connection setting) Once connected the word "Serial" on the top of the screen will change to "USB". It is advisable to use only the original cable. Also connect the cable directly and not through a hub. Now reflash the rom and do a hard reset. I have faced problems by softreset after upgrade please try hard reset.
Hopefully your problem will be solved by a reflash.
Best of luck
Click to expand...
Click to collapse
boss ... please help me ..... i have a dopod 900 ..... but it can not enter bootloader or hard reset .... ditancap usb cable, charger lights flash .... Please help keep the boss. ... thank you
Welcome to forums
Have a read on my signature link, you´ll find a lot of interesting information to recovery your Universal.
Good luck,
flash with tomal roms
Welcome to forums
Tomal ROM´s are indeed fast and stable
manybe you can nmsm your original rom again
Try update bootloader to 1.01 _ttp://rom-update.ru/programs/dd48795954c166e9431f4127c130d474.exe
German Qtek 9000 CID unlocked, hardSPL'd
running MaxStegiROM
Tried to upload D-Two's ROM.
Everything went fine, upload 100%
then: upload error.
screen went black, no reset works
no USB or Serial to be read on dark screen.
Tried battery out (battery is charged), no reaction.
When connecting to PC the red charging LED lights up for
some minutes, then goes off.
PC says connected unknown device ain't working properly
(other Qteks are recognized properly)
Trying to re-flash gives connection error when pressing "update".
Any idea?
Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..
...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?
I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get
hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work
...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn
Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p
ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000