Develop Bugs

MaUpgradeUt_noID.exe and Qtek (error 120)

could somebody explain me hot to exactly remove this country Id Error.
I read the wiki article and excecuted it step by step. nothing.
First of all i have a QTEK 9000 with latest qtek rom. My bootloader version is 1.00. These are my steps. Does somebody recognizes the mistake
1. Firewall is disabled
2. Activesync 4.2 doesn't allow USB connections
3. Device is connected directly to the usb port
4. When in bootloader mode the device is recognized as smartphone
5. When i start MaUpgradeUt_noID.exe i get NO overview on what is the version number of the firmware etc.
6 I wait >5 sec and press update.
7. the upgrade tool says "congratulations" please hard reset
8. I hard reset the device.
9. when I try to install IVANs AKU 3.2 rom i still get error 120
Any advices???

you have to unpack the aku 3.2 en then put the MaUpgradeUt_noID.exe in the same folder where you unpacked the aku3.2 and then it will use the cabinets to upgrade, what you did at first is, you run the MaUpgradeUt_noID.exe, but that exe file needs the aku3.2 files..
steps you have to take are:
1. unpack IVAN AKU 3.2 rom
2. put MaUpgradeUt_noID.exe with the aku 3.2 files
3. Activesync 4.2 doesn't allow USB connections
4. Device is connected directly to the usb port
5. Put device in bootloader mode
5. start MaUpgradeUt_noID.exe
6. you know the drill... should install in about 30 to 50 minutes...

[ITA] Artemis Bigix 2.0

Another Rom for Artemis italian user.
This is a new way of install ROM and can be installed ONLY if you have a Micro SD with almost 30 Mb free space.
In Rar archivie there is the nbh file (the Rom) and a file called "Setup".
1. Copy file "Setup" in your SD
2. Flash the rom (remember you must have SPL unlocked).
Don't delete Setup from SD: it's impostant if you make Hard Reset.
Core wm: CE 5.2.1620 (Build 18124.0.4.2) from original HTC WM6 Professional Ita
SplashScreen
SHDC e GPS Photo ready
.........and more.
Italian user can read more on this forums: A1Ktyle - SoloArte
LINK DOWNLOAD RAPIDSHARE

Thanks mate, testing your great work, bye

P3300
My HTC3300 was dead, only can load into Three-color Mode with USB avaliable. I tried all kind of RUUs, including the Original ROMs(English, French, Deustch....)and the newest version , all report ERROR[300]invalid update tool. then the screen of phone stayed in 0% and RUU tool exit only...
IPL 1.27.0001
SPL 1.11.0000 (used the USPL to unlock CID before)
Before Bricked, I successfully updated many versions of ROM, and the last operation is WM6.1.
I'have try this with MTTY:
Cmd> set 32
Cmd> password BsaD5SeoA
Cmd> ruurun 0
Cmd> ResetDevice
But Doesn't work!
because of you!
My phone was perfect before and I have installed your BigiX.
What I have to do? Can U help me?
I can donete some money... pls... help me....

My dear friend,this is an old rom.
But this is not the reason of your problem.
I don't know if MTTY works on this device, but if your screen show 3 colors you are in bootloader mode (and your SPL is 1.11.0000 as you tell, so it is good for flash any rom).
So (in teory) you can connect PPC to PC via USB and run RUU for flashing the rom you want.
In alternative you can flash original rom.
For this operation i suggest Win XP+ AS 4.5 and try to change usb cable (a new one) and usb port (another on your PC)
I hope you can resolve.
No need donate money

Thx, but are 3 days that I'm looking for solution... Lot of people have the same problem. When run RUU flashing after 3 colors bar, the phone start to flashing but is stopping at 0% and the software report ERROR[300]invalid update tool.
I can connect only with MTTY but I'm looking fore some command that can force to send RUU at the fone. For example "send" in telnet. But nobody know how to do this...
If someone have an idea, lot of people will be very very very happy!
And hope gratful

You can try with rom flash from SD card...
Are you italian??
You can found all the info in this website -> Clic here!!!

Yes, I'm Italian.
I'll post this question to that site.
But I think that is possible to force installation of RUU with MTTY.
My problem is that when I have used start_uspl.exe at blank screen was blocked and I have removed battery.
After this my phone is blocked with 3 colors bar and when I try to update, it start but only at 0%
I need to know all MTTY commands

I don't know if MTTY work with P3300, try with the flash from the SD card directly from the device...
This is the link of the discussion...... Click here!!!
Try don't cost anything....

obviously I have try a lot of times... But doesn't work!
I have try to rename in ARTEIMG.nbh and in a lot of different name but when I powe the phone it say Checking SD contents but nothing happen....
I would like to find a command to force reading of SD and writing to the Phone... but I think is not easy...
Thanks whatever....

Do you try with another SD card?
This procedure is the same that the HTC Service use for repair the HTC device...
Try with another SD card... I have a Kingston 2Gbyte and it work very fine!
I hope your Artemis revive very soon!

I have only 2 SanDisk SD cards. One of 128Mb and one of 2GB.
I have tryed with both. With Fat16 and Fat32 but nothing happen...

Sorry for your problems Pinco, I don't have a solution for that but i can strongly recommend another ROM from the great BigX, the one you can see in my signature. OS core seems to be more recent and ROM's almost perfect If you don't have any specific need to use the 2.0, go for Blue-X!

help error 300
what happend any there have solution for this prob

My FSC-n560 is bricked. Help please!

Hi!
I was using Newplow's WM6 038 ROM with my N560.
Yesterday I tried to write another ROM(WM6 038 with 8MB pagepool) but during update got an error.. It said it just failed.
Now my N560 is stuck on booting screen(people climbing mountain..)
I tried Warm, Cold, Hard reset but with no luck.
Even the power button doesn't work so I had to remove battery. When I insert battery it powers on by itself.
I can enter bootloader screen by pushing power+record button so I tried to copy rom image file to SD card but it doesn't work.
I tried two ROMs(OS_213U.nbf from Original WM5 ROM and Newplow's) and 3 SD Cards(2GB SD, 1GB MicroSD with Adopter, 16GB SDHC)
Is there any recovery tutorial in bootloader mode?
Help me please!
Sorry for my English.

Have you tried flashing a ROM through the computer rather than the memory card? Try going into bootloader and flashing that way rather than the card.

The pagepool ROM is meant for N560s that have been upgraded to 128Mb RAM... have you upgraded the internal RAM to 128Mb? If you have not, then this may have caused your problem.
I had this problem when flashing to 038 normal RAM (from 035). A hard reset reset to the normal start screen, but nothing worked. However, trying a new burn with the Loox flash tool restarted the process and it worked. I found the cure was to make sure you hard reset the N560 before doing a burn. It appears to be that you have to do this to release enough RAM for the burn program to reside and for "working" storage. You may not have done this.
I suggest you try simply re-running the flashtool with SD/SDHC cards removed, battery in place, on the cradle via your PC, even though it appears stuck. The signals coming from the USB link may wake up the bootloader routine in the N560?

Solved the problem! Thanks for your comments!
I asked same question in Newplow's guestbook and the person who made pagepool rom answered. I used MTTY to revive my pda.
What I did is in below post. need translation
http://4pda.ru/forum/index.php?showtopic=55274

Hi all,
I have the same problem. N560 is stick on the himalaya picture. I tried to falsh from WM5 to new rom for Wm6 and after installation the pda stuked. So I did a warm reset and now only the start picture is apperaing. Problem is that battery is down now.
Can someone give more info on the process followed to revive the PDA ? I just cannont read russian (may be Jinsu77 ?)
Many thanks for support in advance

same problem here please please please someone help us
the only thing i can do is the l c:\os_213u.nbf on mtty program and nothing else happend to the machine
sorry for my english

read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.

It was me asking on Newplow's guestbook.
In case you're using Vista, you need some trick to be able to rom update. Read below.
http://www.modaco.com/content/windo...u-on-vista-it-can-be-done-the-ultimate-guide/
And then you need to download MTTY (I used version 1.42, got it by googling) and follow below steps.
(used google translation from 4pda.ru)
------------------------------------------------------------
For rom update without ActiveSync.
1) take this set of extract, copy it to the folder with the firmware.
2) copy the file os_213u.nbf example in C: \
3) You press the button Recorder + food and poke in the hole reset (Recorder button and hold until you eat dolphins)
4) plug the device to a PC, the Task Manager, shooting process - wcescomm.exe
5) Run mtty, choose Port: USB, connect.
6) If mtty caused an error and shut down, simply restart mtty, if not typed commands, then repeat the procedure with paragraph 3.
7) in mtty command, enter: (first letter in kommande - a little l l от слова from the word L L oad)
> l l c:\os_213u.nbf c: \ os_213u.nbf
Since the end of the process will be an inscription about the error, remove the device from the PC.
9) Run rom update, zhmete "next", until you see dolphins.
10), plug the device to a PC and program.
---------------------------------------------------------------
Hope this helps you all

in advance sorry for my english
I am doing all the instructions carefully and the mtty show this
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,1A0F023Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
the pda shos the dolphins and the full blue bar
after without change anything i run the PocketLOOX5xxFlashTool that i have in the same folder with the :
EnterBootLoader.exe
OS_213U.nbf (originally rom)
RUUServer.dll
RUU.dll
and the only thing i can see is that the PocketLOOX5xxFlashTool is trying to find the pda without any luck
also the pda is stucked in the same screen with the dolphins and the blue bar
do you see any mistake in this procedure

Helppp!!! please

tuluba said:
Helppp!!! please
Click to expand...
Click to collapse
have you closed EVERY process of activesync before proceding with mtty?

I close the wcescomm.exe and the rapimgr.exe is there anything else?

The pocket LOOX 5xx FlashTool cant connect with the N560 and at the and says that Error"The language in this Flash Image update (ENGLISH) differs from that on your device()!" and i have always english rom exept maybe from the last rom "the killer" with the 128MB rom that i dont know if it is an english or something else because the device never opens to see

After flashing in MTTY(don't care about error messages), you need to unplug your n560 from PC. And then proceed romupdate until you see the dolphin picture. Now you plug n560 to PC and cilck next and wait for a while.. Hope it works!

I change the language of the rom and it works
thank very much all of you

At all they have Probs with flash from SD Card: only use a Card with 512MB! I think a Card greater then can't read by the Bootloader....

hey.
i am compeletly new here. I have the same with my n560. I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP

if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)

Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????

ChrisDo said:
Need help!!! Please!!!
I bricked my N560. I tried to downgrade from WM6 to WM5 and now I see only delfins and in the first line "2.14.G4" and in the second line "2.15"
What can I do?? How can I flash WM6 or WM5 ROM when there is no connection to the PDA????
Click to expand...
Click to collapse
You can usually get back to the boot loader if you do a hard reset. I am sure you know how, if not you will find it in the FSC CDROM manual that came with the device. Let us know if this works? I have got stuck at this point too, so I know it works..... hopefully!

Binatone Careera_x430 Or Roadfinder Pns_143 Flashing

I have a Roadfinder 143 or more well known Binatone carrera x430 Pna specs i know so far:
Display Touch Screen 4.3" TFT LCD Resolution 480 x 272 pixels
SD/MMC Card Memory Up To 2GB
GPS chipset Sirf Atlas III
Processor Centrality Atlas III 372MHz High Speed ARM926J
Operating system Microsoft Wince 5.0 Core Version (Macallan)
Speaker 1w I Have Changed it with a internal very powerful speaker!
USB USB 1.1 and 2.0
TMC output
Headphone output
Memory on Board ROM/RAM up to 2GB / 64MB
Battery/Type Built-in 1450 mAH li-polymer
Weight 200g
Dimension (mm) 127 x 85 x 19
What i want to do:
Export the rom so i can unpack it and make a few changes.
I would like to find a way to flash it with clean WindowsCE core5.0 (Or other if possible)
I cant figure out how to go into bootloader mode...
I want to take advantage of this big screen and transform it in to a pda. It doesent have camera,phone,gprs,3g,wifi,bluetooth,irda,
so no need to find drivers for them it souldent be to hard to make/edit a rom for it.
It has very large internal memory in a resident flash drive as it calls it 512mb that's without the rom memory size on the current setup that it has everything locked up!
I've managed to get an explorer running and put extra stuff in but the registry gets cleared on every reboot its so very limited....
Can't i just Run an app to make a backup.img/.nb0 of the existing rom take the drivers that i need from it an get a clean wm5 image and put the drivers in flash it by active sync or most probably sd and have it free???
Please give me a bit of help i would gladly donate for someones effort to help me! Im not a complete noob and many others would like this and use it because its a cheap good pna in Grecce,America,China,France,Europe generaly,Australia. There is also a smaller version of this pna with 3.5" screen and 256mb internal flash memory
Feel free to comment and direct me advise me. (Alex)
These are the link to pages that sell this device:
http://binatonegps.com/gps/_global/product_detail.php?item_id=4
http://www.kotsovolos.gr/site/product.jsp?catid=53081
http://www.myphone.gr/forum/showthread.php?t=219937

Firestarter42 said:
I have a Roadfinder 143 or more well known Binatone carrera x430 Pna specs i know so far:
Display Touch Screen 4.3" TFT LCD Resolution 480 x 272 pixels
SD/MMC Card Memory Up To 2GB
GPS chipset Sirf Atlas III
Processor Centrality Atlas III 372MHz High Speed ARM926J
Operating system Microsoft Wince 5.0 Core Version (Macallan)
Speaker 1w I Have Changed it with a internal very powerful speaker!
USB USB 1.1 and 2.0
TMC output
Headphone output
Memory on Board ROM/RAM up to 2GB / 64MB
Battery/Type Built-in 1450 mAH li-polymer
Weight 200g
Dimension (mm) 127 x 85 x 19
What i want to do:
Export the rom so i can unpack it and make a few changes.
I would like to find a way to flash it with clean WindowsCE core5.0 (Or other if possible)
I cant figure out how to go into bootloader mode...
I want to take advantage of this big screen and transform it in to a pda. It doesent have camera,phone,gprs,3g,wifi,bluetooth,irda,
so no need to find drivers for them it souldent be to hard to make/edit a rom for it.
It has very large internal memory in a resident flash drive as it calls it 512mb that's without the rom memory size on the current setup that it has everything locked up!
I've managed to get an explorer running and put extra stuff in but the registry gets cleared on every reboot its so very limited....
Can't i just Run an app to make a backup.img/.nb0 of the existing rom take the drivers that i need from it an get a clean wm5 image and put the drivers in flash it by active sync or most probably sd and have it free???
Please give me a bit of help i would gladly donate for someones effort to help me! Im not a complete noob and many others would like this and use it because its a cheap good pna in Grecce,America,China,France,Europe generaly,Australia. There is also a smaller version of this pna with 3.5" screen and 256mb internal flash memory
Feel free to comment and direct me advise me. (Alex)
These are the link to pages that sell this device:
http://binatonegps.com/gps/_global/product_detail.php?item_id=4
http://www.kotsovolos.gr/site/product.jsp?catid=53081
http://www.myphone.gr/forum/showthread.php?t=219937
Click to expand...
Click to collapse
You may need platform builder to generate a ROM for that device. But going to bootloader mode is still unknown for me.

Bootloader mode drivers
I think i have found how to go into bootloader mode, i keep the side power button pressed for a bit while switching the device on and then connect it to the pc and it comes up as a unknown usb device and prompts me for drivers and stays there!!! the thing is i can't get any thing to show up on the screen... Maby thats the bootloader type that it has by factory and doesn't show anything up on purpose...
Where do you think i can find drivers for it? i have realy looked everywhere that i know... Help me please guys...

try the voxtel carrera 430 file (prosh_430)
holding down the sleep button and press reset
after some 20 sec you will see the download image menu
release the sleep button
after 10 minutes you will have a brand new voxtel aka binatone.
but the menu is in russian so you have to find the buttons to change the lang in english and to calibrate the screan

ASUS P535, bricked, PDAMobiz wm6.1.

I have a ASUS P535 that had working wm5 and I was going to upgrade it to PDAMobiz wm6.1.
I tried to install "PDAMobiz_P535_WM6.1_Build19716_1.1" but got message Update Fail at 80%,
because I had bootloader 06xxxxx.
So I searched at the forums at the web and found someone that gave me help, as following.
"You need to flash the sorg ROM, just choose the base version (appx 30MB),
install that first then you will find that your boot version had been change to 07xxxxx.
If there is any update fail during flashing the sorg ROM just ignore it. Then you flash the vivi ROM.
Link to P525.WM6.1.v0.11.Base.by.Sorg. Just run the rom flash... it'll take care of whats needed"
I installed P525.WM6.1.v0.11.Base.by.Sorg hoping that it will upgrade the bootloader but...
After this I cannot get past the bootloader "galaxy .nb0" not found, and second flash message insert sd card.
Screen is dark and i can barely see all the text in the bootloader.
I have the PDAMobiz galaxyII.NB0 in the SDcard but it doesn’t recognize it. If I put a galaxy.NB0 from Sorg
it starts to install but gives at the end Checksum ok! Update fail.
How to install so that it can recognize PDAMobiz galaxyII.NB0?

Make sure you have formated your memory card first and leave only galaxyII.nbo file in memory card <no folder or any other files>
Then try again. Get the rom from www.asusp535.com. It works for me.

that didnt help me.
i got almost the same problem
i got a P535 with no WM on it. (found it)
i've tried to put a WM6 on it, but it says Update FAIL !
if i copy any GALAXYII.NBO on my miniSD card, it says GALAXY .NBO not found. thats when i rename the GALAXYII.NBO to GALAXY.NBO, but then it says Update FAIL !
i dont know what to do with it
PLEASE HELP!

It worked for me too but I had WM6 official one from Asus before flashing to PDA Mobiz WM6.1
Is your SD Card formatted correctly and is of the right size?

i got a 2GB miniSD card.
i've formated it once in FAT (full format), then before i put a GalaxyII.nb0 i format it quick
do i need to format it full before i put a GalaxyII.nb0 on it?
p.s. can i change the bootloader too? maybe the bootloader is broke
exemple using: PDAViet_WM6.1_19900
when i put a GALAXYII.NBO on my card it says:
2007/05/18 18:03:59
CPU Version: PXA27x
Force Mode!
USB Cable PlugIn.
GALAXY .NBO not found /MicroSD card Inserted
Waiting...
when i rename the GALAXYII.NBO to GALAXY.NBO it says:
2007/05/18 18:03:59
CPU Version: PXA27x
Force Mode!
USB Cable PlugIn.
MicroSD card Inserted
GALAXY.NBO found
Checksum ok!
Update fail!
Reading...
well, i've tried wm5, wm6, wm6.1, wm6.5... non of them worked , i guess the phones bricked
any suggestions?

no one?
please

Try this
You could try this:
Go here http://forum.xda-developers.com/showthread.php?t=423148&highlight=p535+rom and update your bootloader to ver.070518180359 according to the instructions(copy BootGalaxy.NB0 to the root of your Storage Card, connect adapter and push Record+Reset ),then try to flash the ORIGINAL asus ROM.Once you got that,run the asus unlocklang utility from the phone.
After that you should be able to flash any ROM on your device.
A lesson learned from failed flash attempts and bricked devices:
Whatever should happen NEVER UNDER ANY CIRCUMSTANCES-NO MATTER WHAT,don't interfere in any way with the phone during the update of the bootloader.NO MATTER HOW LONG IT TAKES.Better charge your battery to 100% AND also have the phone connected to its charger.
A failed ROM flashing can be corrected,a failed bootloader flashing will kill your device for good.
P.S. whatever you do you do it on your own responsibility,i take no blame for a bricked device.

ํYou do it wrong step.
This rom is worked.
You should be flash WM 6 before.
WM5-->WM6-->WM6.1

It still does not work. I had mine at service (not asus service),just a regular mobile-phone shop which had also service. They could not repair or find any solution for how to fix the p535. So i am stuck with a phone that just wont work. Maybe Asus service could be able to fix it or not.
My phone screen is very dark and only text that is displayed follows:
2007/05/18 18:03:59
CPU Version : PXA27x
USB Cable PlugIn.
Galaxy .NB0 not found (flashing text in RED and with other text in black) MiniSD card inserted
...and at bottom of screen is:
Waiting ...
My conclusion is that i will probably buy new phone to replace this bricked one. A HTC HD2.

Your phone is fine... Just use the USBLoader.exe method... That happened to me a couple of times lately too, dunno if it's an SD Card problem or what...
Basicly, boot into the bootloader, connect it to your Windows PC, and update the rom from the PC...
The comand should be Usbloader.exe GalaxyII.nb0.
I'm sure it works, just hope you can give it a try, and preferably using XP since with vista you'll have to use the HTC old drivers so he can recognize the phone...
I'll leave the USBLoader so you don't have to search it... Atention this is not a Zip file, i just renamed the extension, so just rename it to USBLoader.exe
I wouldn't mind to get a Diamond2 either But i hope this helps getting your P535 to work again...

I would like to try if it works, but how to exactly do the Usbloader.exe method? Which buttons to press on the p535?
I tried and got this message in cmd:
C:\p535>Usbloader.exe GalaxyII.nb0
#####################################################################
# USB image transfer tool for Intel PXA27X USB Development Board #
# Version: 1220'04 Author: O.C #
#####################################################################
try to open \\.\wceusbsh001
try to open \\.\wceusbsh002
try to open \\.\wceusbsh003
try to open \\.\wceusbsh004
try to open \\.\wceusbsh005
USB pipe opening error
Anyone know what it means? I have XP not Vista.
I have now tried on 2 laptops with XP and with same result.
My phone screen is displaying:
2007/05/18 18:03:59
CPU Version : PXA27x
Force Mode !
USB Cable PlugIn.
...and at bottom of screen is:
Waiting ...
Is it possible to maybe fix it? Is there any hope, maybe it is just half bricked.

That's exactly how it should be, you just need to either stop Activesync or install the HTC AS 4.0 drivers... Then the device will be recognized in that first usb port...
And no your device isn't bricked, the it's just the rom messed up if you can into the bootloader it's almost guaranted you can recover it

Please, can anyone post a link to where i can find the "HTC AS 4.0 drivers".

I will post couple of pictures. First is the error message from cmd. Second is with ASUS P535 and the message that it display.
This is pictures when i try to use the boot loader method. Nothing happens.
Yesterday i tried again to put galaxyII.nb0 on the card and flash it from there but message was:
2007/05/18 18:03:59
CPU Version: PXA27x
Force Mode!
USB Cable PlugIn.
GALAXY .NBO not found /MicroSD card Inserted
Waiting...
when i rename the GALAXYII.NBO to GALAXY.NBO it says:
2007/05/18 18:03:59
CPU Version: PXA27x
Force Mode!
USB Cable PlugIn.
MicroSD card Inserted
GALAXY.NBO found
Checksum ok!
Update fail!
It is frustrating not to fix this. And when i use usb i get:
C:\Usbloader.exe GalaxyII.nb0
################################################## ###################
# USB image transfer tool for Intel PXA27X USB Development Board #
# Version: 1220'04 Author: O.C #
################################################## ###################
try to open \\.\wceusbsh001
try to open \\.\wceusbsh002
try to open \\.\wceusbsh003
try to open \\.\wceusbsh004
try to open \\.\wceusbsh005
USB pipe opening error
Can anyone help me with my P535? I have tried everything but maybe i have missed something. Searching the google and various forums in different languages and still nothing.
My last resort soon will be to send this forum thread with questions to asus support and hope for some answers. What to do, how to do it, which files do i need...
And if you people that try to help me need some more information or pictures of my mobile just tell me. This is the best smartphone i ever had and it is shame to waste it.

kill Activesync from task manager first

Doesn't work.

Sorry to ask but why did you flashed P525 rom to P535 device? and why didn`t you upgrade to WM6.0 official Asus rom first then to WM6.1 custom rom?
Sorry I have no fix for your device.