Dear All,
I've a problemi with my SPV M5000. After firmware upgrade, my device is stay in USB or Serial mode. I try hot and cold reset but no result? after few seconds it's back to USB or Serial Mode?
So, please help me!
Ever heard of searching the forums? As this has been asked before...
If the resets don't do it, reflash it.
Re...
I try to reflash, but my firmware show "Country Error"
I'dont have noID file to this model? If you have please send me to [email protected]
Re...
I try to reflash, but my firmware show "Country Error"
I'dont have noID file to this model? If you have please send me to [email protected]
Related
I got this "ERROR 100: MODEL ID ERROR",... pl help
I try to upgrade XDA2 rom from "ruu172104wwe_t-mobile-uk" to "XDAII_172181_Final" and I got this error "ERROR 100: MODEL ID ERROR"
How can I slove this problem?
First I have O2 rom and I upgraded to "ruu172104wwe_t-mobile-uk", when I try to upgrade to "XDAII_172181_Final" everything look fine till the error occur I can open my O2 anymore on the screen show just message "serial v1.03"
Please help,.. Thank
i'm assuming you have a wallaby?
try reflashing using sd method.
dl nb1 file from kitchen
use xda-rools to write nb1 to sd
insert sd into wallaby
press pwr button and reset at same time
good luck!
Thank you for suggestion, but I'm very new for O2.. and I use XDA2
Could pl explain more,... how can i get nb1 (where is kitchen) and what's xda-rools? does it will work with XDA2?
sorry to ask boring question but i really dont know.
you are using O2 XDA2 ,right! do a "cleanjumper" , if you want update , under you use a t-mobile rom, the easy way!!
while i upgrade to wm06 i get this error.
spl : 1.04
rom version :1.25...
please help me
I have got same inf when use RUU, but my spl is 1.01.
what shall we do
my
ipl :1.01
spl:1.04
radio :1.07
rom version : 1.25.207
now i cannot install wm06 tom my xda trion also htc hermes.
i dont know why i get this error. the usb is allways connected to laptop. and it is not deffect.
please help us friends.....
and i cannot succees bootloadermode by pressing power + ok and then stylus
why dont it go ?
and now it is ok. at the end i use wm06.
my steps was so.
if you start wm06 you get this message. go on insitalling on breck up.
ms corporation suggest to abort it.
you klick on "installirung fortsetzen" then you get an other error massege
error 264 when you get this error massage make a soft reset your hermes.
and i said before you are now on WM06.
Hi Guys, sorry my english (i'm italian). I wrote u because when i installing wm 5 on xda IIs, i have a error. I follow what is write here
http://forum.xda-developers.com/showthread.php?t=283282
and This is what i do:
i have copy getdevicedata on Secure Digital and i put sd in ppc. I open this file from ppc and it lock on boot loader. Now appear "serial" or "usb" if is connect on cradle. I try to reset, hard reset but anything is happened. Please help me, what can i do?
Very very thanks
Someone give me a solution?????
http://wiki.xda-developers.com/index.php?pagename=BA_1.42.00_Upgrade
when it says serial it's ready to get upgraded with a rom like the wiki describe
when i was try to flash my O2 exec to WM6.1 CHT, i click the EnterBL.exe without connect to PC, and the screen dim and only shouw USB V1.00.
I try to hard reset it, but no use.
can anybody give me some suggestion(s)?
u can get help from here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
Hello,
I connect my qtek with pc. I tried to install wwe rom - from german to english. I ws downloaded english rom but cant install coz i have problem with COUNTRY ERROR -ERROR 120 atfer that i install in qtek "MaUpgradeUt_noID".exe and after that my qtek go to hell.
when i done hard reset on the screen write only: Serial and v1.00!!!!
..............qtek is dead...................
PLzzzz people help meeeeeeeeee
what can i do now for repair my qtek?????
p.s. srry for my bad english
Kind regards
Your Uni still alive
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
AIN1 said:
Try to download "Exit Bootloader.exe" from wiki, conect the uni to USB and Run the applcation...
If you uni is death when the Bootloader is lost. I brick my Jasjar when the Bootloader was gone, dont worry Try to read more in the forum Universal WM6.
Click to expand...
Click to collapse
Hi AIN,
Thnks Mucho Mucho!
My Problem is, that i can only choose Com 1 to Com 3 in mtty 1.42 - Because of this i can't use the methode which is explained. - What i am making wrong? - I use a Sony Vaio Laptop for booting...
Thanks a lot!
if you have the rom try tis out!
1.unzip the file!
2.put the rom-extended rom-radio(or whatever you need!) in this folder
3.when you'll connect the phone on the usb,on the screen you have to see "usb v1.01".
4.run the "MaUpgradeUt_noID.exe"
5.wait till it will finish flashing!!
6.enjoy the new rom!!
qtek pu10 0r 9000 is freeze please big help
please big help / i just try to change language on my qtek 9000 and when the phone finish. and the screen freeze. and i off it and on it .and still the display show but freezing. and it can't connect to the active sync and pc /please help
Try a soft-reset first.
If not, you may have to hard-reset. You will lose all your data and programs you've installed and it will revert to factory state (or last flashed ROM).