Dies anyone know or have the cab and ini file to enable my XDA to talk to my wired gps. I am running tomtom 5 but it wont wake up my gps for some reason. It has been working fine for the last 3 months
Related
This has been frustrating for me.
Been playing arround for hours to get TOM TOM 3 working with my Xda2's.
Can't seem to get the Bluetooth GPS Recevier to work properly.
I have paired the device.
I can see the GPS OUTPUT service however there is nothing incoming on both fronts.
Am i missing something or can any1 help.
Have you installed the 3.07 update from Tomtom?
Apparently this is required to get it to run properly on the XDAIIs
I wouldnt know yet as I'm still using an old Ipaq - waiting till I get paid before I buy a gps mount and use that with my new Xda
You can try so: launch navigator 3; go to GPS (clicking between Status and Log); on top you must see: TomTom Wireless GPS and Bluetooth Serial Port COM6, and the little square signed. So, the two devices would be connected.
A fix
Thanks for the last comment. It seems like it works with the COM6 port.
Dont know if anyone else has come across this problem or my gps is crap. Takes ages and very clear sky to find satellites. apart from that when i go through blackwall tunnel the gps stops (obvious reasons) but then does not start again on the other side. what i dont understand is why cant it connect to satellites like in-car navigation systems.
Do you think a gps aerial will make a difference??
Definately,
I have a GPS antenna, and it improves reception greatly usual satellite locks of between 8 - 12 sats and quick TTFF
What GPS reciever are you using ?
Do you have recieve all incoming beams unckecked ?
You will find it here :- Start/settings/connections/Beam.
I have an M1000 and an O2 XDA II and both lock on and get a fix in less than 30 seconds I am using the tomtom bluetooth GPS reciever with tomtom 5.
What GPS reciever are you using ?
Do you have recieve all incoming beams unckecked ?
You will find it here :- Start/settings/connections/Beam.
I have an M1000 and an O2 XDA II and both lock on and get a fix in less than 30 seconds I am using the tomtom bluetooth GPS reciever with tomtom 5.
I have got a socket/EMTEC Blutooth GPS that i have had for years, it cost me over £200 when i first bought it and i have never had a problem at all once i bought an antenna for it (the antenna was a no name solution)
as for the incoming beam settings, it makes no difference to me with or without it set, but i personally leave it not set to save battery life as i have never had a need to use it in over 4 years of having a pocketpc
Greetings,
I have tomtom navigator installed on my XDA IIs and i have polstar bluetooth GPS, BT 111, they both work fine and excellent, but the problem is, the next time when i switch on the bluetooth gps and tomtom on my XDA, tomtom doesnt detect the gps itself, I mean i have to delete the bluetooth entry in the bt manager of XDA and i have to add this new bt connection and all the bt setup again, why is it, can someone please tell me the solution to it, i mean like is it possible tht everytime i switch on tomtom on XDA it automatically detects my bt gps receivers.
Plz, thanks in advance
cheers
First of all make sure you have TomTom Navigator version 5,21 loaded on the device. Then create th ebond between the devices, and set TomTom up to use "Other Bluetooth GPS". If you have done all this how long are you waiting for the XDA to switch on the BT and find the GPS? it can take upto 45 seconds on some devices, if you need TTN5,21 download it from www.tomtom.com as it is free - Mike
I'm running TTN 5.21 on my XDA IIs with no problems, I don't even need to do anything with the bluetooth, it automatically turns on the bluetooth when I start TTN and turns it off when I close, and it automatically picks up my TT BT GPS dongle. Although there is a max 5 min wait to get a valid GPS signal.
I installed the 5.0 version then used the update from the web site afterwards.
Gav
Hello, I have installed TomTom Navigator 5 in my Qtek s200, but I can't connect it with the bluetooth GPS if the telephone is switched off.
Tomtom runs ok, but doesn't find GPS device.
If I switch on the telephone there isn't any problem, tomtom runs ok and find the GPS device.
I have used tomtom, and dell GPS bluetooth GPS reveivers.
Someone knows if is there a solution to use the GPS with the telephone utility switched off?
Thanks!
ive got this problem too with my xda 1 which i only use as a satnav unit
I use the xda with a wired gps but tomtom complains there is no gps device because the unit is in flight mode, even tho im not trying to use any wireless signals.
anyone help ?
thanks.
I don't know if I understand you right, but I might have an explanation for this. On my Qtek 9100, I can't use a bluetooth GPS-receiver when the device is in flight-mode. Flightmode disables all radiosignals...and since bluetooth is sort of a radio signal, it's disabled as well
A solution might be to turn off and on your device and "cancel" when you're asked to enter your SIMs PIN-code. This way, the device is not in flight mode (so bluetooth works) but the telephone-reception is disabled.
I hope this helps, if not: let me know!
--Marc
yes that works but the phone device is still switched on so uses battery
the gps in question in my situation is a wired unit going directly to my old xda 1's com port so shouldnt matter if the phone or bluetooth are on or not. Even if the pda was in flight mode it shouldnt affect use of my wired gps as there are no radio signals.
seems like a 'bug' in the tomtom software that if the pda is in any kind of flight mode including the phone being off, it decides it cant communicate with any gps, no matter how its connected, as if they expect everyone to be using bluetooth gps' and just include the wired configuration as a legacy function.
malty
maltloaf said:
yes that works but the phone device is still switched on so uses battery
the gps in question in my situation is a wired unit going directly to my old xda 1's com port so shouldnt matter if the phone or bluetooth are on or not. Even if the pda was in flight mode it shouldnt affect use of my wired gps as there are no radio signals.
seems like a 'bug' in the tomtom software that if the pda is in any kind of flight mode including the phone being off, it decides it cant communicate with any gps, no matter how its connected, as if they expect everyone to be using bluetooth gps' and just include the wired configuration as a legacy function.
malty
Click to expand...
Click to collapse
Darn...sorry, I misunderstood. I'm using a bluetooth GPS-receiver myself, so I just took for granted that you also used a bluetooth device And indeed, looks like a bug...not very convenient.
--Marc
Concerning bluetooth devices:
This seems not to work with Windows Mobile 5.0.
With Pocket PC 2003 devices it is possible to use with TomTom bluetooth while in flight mode.
Here's a work around for Win 5.0:
1) Enable the phone and bluetooth in the Comm. manager.
2) Make the link to thte bluetooth gps in TomTom.
3) Disable the phone in the Comm. manager.
4) Return to TomTom.
The bluetooth link will be maintained until you exit Tomtom or try to link again.
This might also be the case with a wired gps.
AJ.
Can anyone suggest a solution to this please. I have tried a couple of roms but the problem is still there.
I am using my Trinity as a modem for my TomTom GO 520 for the traffic service. It starts OK but after a while the TomTom loses connection with the Trinity and on inspection I find that bluetooth has been turned off on the phone. I can turn bluetooth on again but it's not something I want to keep doing while driving.