please can anyone help! mda 3 failed rom update - MDA III, XDA III, PDA2k, 9090 General

could anyone help me out of a mess please , i have recently purchased an mda3 to replace my xda2 , i unlocked the phone which went ok but wouldnt accept my o2 sim , being the same phone as the xda2s i thought maybe it would need the o2 windows version rom on , i selected the wrong rom from my pc and the upgrade stopped after a few seconds stating it was the wrong version but now the phone has no rom on at all just a dark screen with "serial" or "usb" if it is docked . Have i done permanent damage ? any help would be very much appreciated

Your phone is currently in bootloader mode - if you have a valid ROM for your device you should be able to flash it with the phone in the USB cradle (the dark screen should change to USB).
If you don't have a valid ROM, go check out the wiki, there's plenty to choose from there!

many thanks forza , as u can prob guess im new at this !

sorry to be a pain forza but unsure which files on the ftp to use , doesnt have to be the latest rom i just need it to work again , could you also tell me how to execute the files , do they load from the desktop , many thanks bren the amatuer

This page on the wiki lists the available original ROM packages;
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
The T-Mobile UK one (1.42) is the latest version ROM (3rd on the list), so I'd recommend you start with that (it's the one I use).
[EDIT] just noticed you're showing as being on O2, further down the list (almost at the bottom of the first section) there's a UK O2 ROM - that may be better for you.
With the phone docked in the cradle (with USB showing on the screen), you can just the run the exe you downloaded and it should flash it for you.

thanks forza ! your a star worked a treat

qtek 9090 with USB V2.06 message error
I have the same problem with my qtek 9090, but I dont can sync my pocket pc. I see only USB V2.06 if the pocket is full charged ( and serial if not on the crable connected ).
Why I can not sync this with my laptop??
I have make a hard reset but still not work!!!
please help me
I have read many post but nothing found...
thank you
scharmander ( newbee )

Related

"Serial v1.06" - i-mate Pocket PC froze

Hi,
I just started with the ROM upgrade of my I-mate Pocket PC to 1.72.00wwe (obtained from the I-mate website) when my phone switched off. Now it only has (at the top) "Serial" and (at the bottom) "v1.06". No matter what I do - soft or hard reset nothing happens, obviously the power button also doesn't function. On my PC desktop I got the message that I need to reset my phone and re-connect.... can't get my phone going, so here I am.
The solution to my problem is (hopefully) simple ? I will really appreciate if you could help me with this ?
not a problem hopefully....u just made HimaClearJumpCode.exe run on ur device(this file exists in ur upgrade folder),and now ur stuck in the bootloader mode....
do the following:
1-hard reset ur device(it wont boot,off course)...
2-put it in the cradle,u should see that ur XP has found a new hardware(if it doesn't,change the USB port)
3-now run the himaupgradeUt.exe.
Now in case(just in case),those procedures didn't work,go to plan B.. :wink:
1-take the battery off ur Himalaya.
2-leave ur device for 12hours(it won't need all that time,but to be on the safe side,u know... :wink: ) without battery,so that backup battery drains...
3-put back the battery,recharge and enter the OS(this option wont work if u have erased the ROM)
4-rerun the upgrade...
good luck.....
RAGO :lol:
Hi
OK, what happens if the ROM is erased.... (judging by the fact that nothing happens when I put it in the cradle - with power on the cradle) ?
My phone was off for about 12-hours - blank screen when I got here this morning.
If I put it in the cradle (and after changing between all the available USB ports on my PC) the PC doesn't detect it - ActiveSync doesn't connect to the phone at all... Note : I have power on the cradle, and it's been a hour now - still just "USB" "v1.06" (or "Serial" if I take it out of the cradle).
:?:
so it is connected!!!!!!!!
since ur serial on the top of ur screen changes to USB when u put it in cradle,then it's connected.... :wink:
now just run the HimaUpgradeUt.exe in the folder that contains the NK.nbf file(32MB,it's the ROM),and it should start the upgrade....
be sure the NK.nbf is a Himalaya ROM....
good luck...
RAGO :lol:
Hi,
Thanks, did it just after posting my reply and everything worked out fine. Note, I just ran the ROM upgrade file (not HimaUpgradeUT), which I got from the clubimate webste.
Thanks, once again for helping me with this one.
Himalaya pocket pc - screen frozen on bootloader
Hi,
My problem is the same - but the difference is that whenever i run the himaupgradeut i get a connection error saying that the PC cannot identify the cradle as connected.
What should I do now?

i have mda pro (PU10) from t-mobile germany need help

hi guys
i have mda pro (PU10) from t-mobile germany need help. i wan't to update to english lang. please tell me wich file need to use. please tell me correct file name. my phone info
MDA Pro T-Mobile
ROM date 08/23/05
ROM 1.12.43GER
RADIO 1.00.02
ExtROM 1.12.127GER
please help me
thanks a lot
hi guys
please help me. now my phone dead only show usb v1.0 and nothing. i'm use this soft:
UNI_TMUK_12032_120_10600_Ship
i'm use reset button no result. please help me. wich file need to use
thanks a lot
hi guys
please help me. now my phone dead only show usb v1.0 and nothing. i'm use this soft:
UNI_TMUK_12032_120_10600_Ship
http://t-mobile.iris-global.com/download_manager_mda_pro.html
i'm use reset button no result. please help me. wich file need to use
thanks a lot
help meeeeeeeeeeeeeeeeeeeeeeeeeeeeee
The latest English ROM is Dopod 1.30.111 WWE(World Wide English) with latest Radio 1.11.00. The second is Qtek 1.30.77 WWE with Radio 1.09.00. They all can download at ftp.xda-developers.com/Universal with user name:xda and password:xda. But, read the detailed instructions before upgrading at http://wiki.xda-developers.com/index.php?pagename=HTC_Universal
Upgrading your device with different ROM wil show you Country ID error and use the program instead at http://forum.xda-developers.com/download.php?id=9885
hi man
thank you for reply mail. i'm find here: http://forum.xda-developers.com/viewtopic.php?t=42743&postdays=0&postorder=asc&start=175
http://forum.xda-developers.com/viewtopic.php?t=42743&postdays=0&postorder=asc&start=125
tell you result later
thanks a lot
hi guys
i have same problem. after update to UNI_QTEK_13077_176_10900_WWE_Ship
my phone not turn on. please help me
how resolve my problem thanks a lot
mrijnvis said:
i had the same with earlier updates. connect the device in a usb port not a hub, remove all cards, sim and memory
update ( maybe 2x because of language fault) then soft reset
in your case, maybe re update 1.09 then softreset
Click to expand...
Click to collapse
I had the same problem with a German T-mobile MDA PRO from Ebay and first think i did was to try and change the language.
First attempt went wrong and the phone would not turn on, but i flashed it again and all was OK.
I think the fault is the way you flash it. I discovered you must follow some important steps.
If the upgrade is a standalone file you must extract the firmware files in a directory like C:\flash (using winrar for example) where you can do the following:
1. Find MaUpgradeUt_noID.exe and later use it to flash, DO NOT USE ROMUpgradeUt.exe.
2. Edit RUU.conf and add [CHECKCEID_TYPE]=1 at the end.
3. Put the phone in bootloader mode (bootloader mode is where it shows usb on top and v1.0 at the bottom, so your phone is allready there)
4. connect usb cable (do not use a usb hub, plug directly on the computer).
5. Run MaUpgradeUt_noID.exe, and ----VERY IMPORTANT---- after the first screen when it displays the firmware version you are about to flash (it does not detect the version on the phone) WAIT 10 SECONDS. Then press continue, and wait for 20 minutes until it finishes.
Hope you make it...
HI MAN
I'M USE YOUR SOLUTION. BUT NO RESULT. ONLY SHOW BOOT MODE. SOFT CAN'T DETECT MY OLD SOFT VERSION. ONLY SHOW NEW SOFT VERSION. OTHER SOLUTION HAVE??? HELP ME
THANKS A LOT
Asxetos said:
I had the same problem with a German T-mobile MDA PRO from Ebay and first think i did was to try and change the language.
First attempt went wrong and the phone would not turn on, but i flashed it again and all was OK.
I think the fault is the way you flash it. I discovered you must follow some important steps.
If the upgrade is a standalone file you must extract the firmware files in a directory like C:\flash (using winrar for example) where you can do the following:
1. Find MaUpgradeUt_noID.exe and later use it to flash, DO NOT USE ROMUpgradeUt.exe.
2. Edit RUU.conf and add [CHECKCEID_TYPE]=1 at the end.
3. Put the phone in bootloader mode (bootloader mode is where it shows usb on top and v1.0 at the bottom, so your phone is allready there)
4. connect usb cable (do not use a usb hub, plug directly on the computer).
5. Run MaUpgradeUt_noID.exe, and ----VERY IMPORTANT---- after the first screen when it displays the firmware version you are about to flash (it does not detect the version on the phone) WAIT 10 SECONDS. Then press continue, and wait for 20 minutes until it finishes.
Hope you make it...
Click to expand...
Click to collapse
hi thanx man for the info but it didnt work for me now my phone is not coming out of bootloader mode....... what can i do now can u help me out of it. my HTC MDA T-Mobile PU10 has chinese wm6.1 installed in it. i want it to work in english. please help me out...............
Hello,
must be to reinstall the firmware.
Here is a link to the procedure:
Code:
http://forum.xda-developers.com/showthread.php?p=8674413#post8674413

HOW TO USE AN ENGLISH ROM to switch the SGH-i718 from Chinese into English

Hi there,
In another post I asked for a method of converting my strictly Chinese SGH-i718 into English. Now, I know that an English version exists, as you can buy an identical phone in English (i think that is the SGH-i710).
Someone posted a link to a file to purports to be an English ROM for the phone, and I have now downloaded it.
Links are http://rapidshare.com/files/45439904/Juggler_WM6_i718ZMGF4_PDA_Eng.rar.html
and
http://rapidshare.com/files/45950071/Juggler_WM6_i718ZMGF4_Phone_Eng.rar.html
How on earth do I use the ROM without totally bricking my phone?
The file is named;
Juggler_WM6_i718ZMGF4_PDA_Eng.rar
When I extract it, I have an EXE file named;
i718ZMGF4_PDA_Eng
which is described as "UnifiedMultiDownloader MFC 응용 프로그램"
When I open it, it has a screen that says "no phone detected" or something like that, and then it closes and the Microsoft Windows Data Execution Protection pops up and says it closed it to protect my computer.
1) Would you trust this file?
2) If yes, how does it work?
Thanks guys 'n' gals
May I ask where you get these files from?
cpz21 said:
May I ask where you get these files from?
Click to expand...
Click to collapse
As listed in the links in my post. They are not mine. The links were provided through another thread on a similar issue.
IT WORKS!
FYI: I used the PDA rom, the first one, and it works! It works incredibly well in fact. After use, when I switched the phone on, it started up in English and prompted me to set the phone up as if it was the first time it had ever been turned on. I will post the full instructions tomorrow (4:30am here and I can't be bothered right now)
It's Done!! Here's How
Well, here's the deal. The forums only work if people help each other. If I were to find out how to do it and not tell you, it would defeat the purpose of having forums and being able to help each other in the first place.
So anyway, I ended up finding a forum with a bunch of awesome Chinese people who helped me to flash it. I already had the file from another forum, and the fact that this guy posted the exact same files, then gave me a step-by-step, made me confident that this flash would actually work.
I have now successfully used the process below to flash the PDA part of my i718. I HAVE NOT FLASHED THE PHONE (RADIO) PART YET BECAUSE MY ORIGINAL PHONE ROM IS STILL WORKING AFTER THE FLASH OF THE PDA ROM.
Here is the process below with no spelling mistakes corrected...
Samsung i718 PPC Phone flash ROM procedure + WM6 English ROM
(A) CABLES
Two Cables are needed for i718 to flash rom.
Cable 1 = USB Cable accompany with your PPC Phone for ActiveSync for the flash of ROM.
Cable 2 = Special USB Phone Flash Cable for the flash of Phone Function ... it seems to be the Radio ROM. It is competible with Samsung normal phone model D828.
USB Phone Flash Cable Info from Taobao site:
Phone Flash Cable 1
http://auction1.taobao.com/auction/0/item_detail-0db2-bd590543d74abee85f6e49e9376b2cca.jhtml
Phone Flash Cable 2:
http://auction1.taobao.com/auction/0/item_detail-0db1-c02f02c2861d77ee6cdc7109e5648732.jhtml
(B) FLASH ROM (PDA FUNCTION)
1. Charge PPC Phone to full power.
2. PC with ActiveSync V4.5 installed.
3. Inside the ActiveSync connection settings, <UNCHECK> Allow USB connections and <CHECK> Allow connections to one of the following: COM? (The port number is your USB will be connected). (trial and error until you get a successful Activesync connection)
4. POWER OFF your PPC Phone and connect it with the USB cable to the PC. (Use cable 1)
5. Run the downloaded WM6 ROM <i718ZMGF4_PDA_Eng.exe>; and choose Detect in POP-UP screen when the program started.
6. Check your PPC Phone is firm connected with PC and POWER ON your phone now.
7. The original ROM program will auto flash the new ROM into the PPC Phone.
8. Just pay attention to the screen of the PPC Phone and follow and instructions pop-up to finish the whole upgrade.
9. After completion, you can check your ROM version inside the PPC Phone, and it will be the new <Version i718ZMGF4>.
(C) FLASH RADIO ROM (PHONE FUNCTION)
1. Install the phone flash driver which is inside the CD that is accompanied with the Cable 2 .
2. POWER OFF your PPC Phone and connect it with the USB cable to the PC. (Use cable 2)
3. Run the bootloader flash program <Qingdao_downloader_v04.exe> inside the folder of <i718ZMGF4_PhoneRom>.
4. In the program screen of <Files to Download>:
1st Boot Loader: Click BIN... choose boot.bin file.
2nd Main Binary: Click BIN... choose i718ZMGF4.cla file.
3rd BP Engine: Click BIN... choose bpexec.bin file.
5. Check your PC's COM number connect with this cable and set the COM Port speed according this cable.
6. Then inside this program choose the Serial Port: COM? (same as your PC's COM Port number).
7. Click the <START> button and it will start to check your Phone ID (if it cannot find the ID, your can disconnect the cable and insert it again to try OR power on the phone to help this Phone ID checking).
8. When Phone ID checking is sucessed, Click the <ALL DOWNLOAD> button to start to flash.
9. After flash is completed, reset the PPC Phone by input *2767*3855# to process.
CAUTION in RADIO ROM FLASHING:
When flashing the Radio ROM/Phone Function or after flash, it will show <Phone Error, Run Later> or similar words. It is normal because the PPC Phone is under phone function flashing procedure and cannot be used. After all upgrade is finished, you just power off the PPC Phone and turn it on again to make it back to normal to fully finish the upgrade procedure.
.....................
So there is it everyone. I hope this helps you to flash your Chinese version Samsung SGH-i718 and enjoy it as much as I am currently.
[email protected]
Taken from here.
By the way there is a newer WM6 ROM for I710/718 (CE OS 5.2.1616 Build 18120.0.4.0)
pierrotee said:
Someone posted a link...
Click to expand...
Click to collapse
hehe.....
I wasn't trying to be surreptitious. I explained that this info was given to me from someone else I was just trying to put it together into a comprehensive post that people could follow and use to flash their phones. I hope it helps
unlock samsung i710
hello can i use this flash rom to flash sasung i710 are they are the same phone like i718 and how to unlock this phone from france network thank you
i710 and i718
maxxamour said:
hello can i use this flash rom to flash sasung i710 are they are the same phone like i718 and how to unlock this phone from france network thank you
Click to expand...
Click to collapse
I'm pretty sure that the i710 and i718 are identical. I think the i710 was designed for sale in western countries, whereas the i718 is specifically branded for Chinese markets.
I think the firmware would be similar, just in other languages.
Give this conversion method a try!
the rom is ok for i710
pda part use usb cable
phone part use serial cable (i used also one prolific based cable)
br
sorinm
how can i use this ROM with vista ( non compatible with active sync)
Tthanks
flashing under vista is not supported! flasher is 2k/xp compatible only!
stability
Hi ,I´m very curious about this upgrade : how stable is tis rom ? what changes in fact ? thanks for any answers.
i have upgraded my phone i710 well but after upgrading my gprs sto working.i tried all kinds of settings but its not working ,is this s a bug in this rom.
i warn all other members too
and pls any one tell me how can i come back to my perivious wm5,bcoz without gprs my ppc s just a brick
jashi said:
my gprs sto working.
Click to expand...
Click to collapse
Don't panic! To get gprs working you must flash both pda and phone parts of firmware. Read first post to learn how to do this. To get back wm5 you need to serach something like I710XEGF2 (xe means russian variant, which is yours i don't know) in google. If you still need WM6, but have no possibility to flash phone part (have no cable etc..) you need to find an official samsung update for I710 (not I718) - something like I710UXEGG1 (U means WM6, XE means russian again).
brother i need my perivious wm5 rom. i cannt live without gprs on my phone.pls give me any link for my i710 original firmware.
i also want to tell u that i had made a backup by using sprite backup,can it restore my perivious wm5 firmware.plsss guide me
Pls attach d picture of flas cable for radio rom,is it available in india.
Or how can i make my new cable
caine said:
Don't panic! To get gprs working you must flash both pda and phone parts of firmware. Read first post to learn how to do this. To get back wm5 you need to serach something like I710XEGF2 (xe means russian variant, which is yours i don't know) in google. If you still need WM6, but have no possibility to flash phone part (have no cable etc..) you need to find an official samsung update for I710 (not I718) - something like I710UXEGG1 (U means WM6, XE means russian again).
Click to expand...
Click to collapse
hi dear,
the version u reffer here for i710 are all downloadede by me but there is no english version of wm5 these all r russian or wm6 (without gprs as i have nt ny cable to upgrade radio).so pls tell me how to find wm5 english rom any link pls.
Hello everyone, I found this thread from google search, I have a China version of SGH-i718+ , This phone was given by my dad, I can barely read any chinese, so I wish could convert this to english version, I believe it runs WM6 Chinese.
Does this rom works for this phone? or is there a newer rom?
and where can I purchase the cables , thanks for the help guys.
this works, just a little change to the instructions to get the PDA part flashing..
- disable active sync usb connection
- disable com port connection
run the flashing program,
select detect & start downloading immediately
plug in your phone and hold the power button until the blue bar starts moving..

Htc P3300 Bootloader Problem !!!

Hello Everyone. I Am Trying To Istall The Official Wm06 But The Bootloader Does Not Respond. Any Sagestions Pls
U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.
Twiggerdingo said:
U give us very little info to respond to
what pc system r u using? What version activesync, what exactly happens (or doesnt), which rom/language, did u cid unlock it (used uspl), etc.
Be more specific please.
Click to expand...
Click to collapse
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .
robinbatman said:
hello again.thanks for the responce. my p3300 has the official wm5. i load the
wm06 (not official) one of the programs that i use in my job dosn't work propertly. so i have to restore in previus wm5. i download fro the site of htc the official wm6. in htc they told me that it is very easy so i could do it my self. i had only to conect the usb cable to the pc (windows xp) and run the file (wm6) i did it but when it start to install the wm6 the activesyng (ver 4.5.0) shut off and stoped the instalation. the screen turn to black. after that the p3300 started again but when i push the voice key and the power key to get in to the bootloader it doesnt work the screen becams to a multi color pixel.the htc told me that i have to replace all the inside hardware. thats all thanks a lot .
Click to expand...
Click to collapse
Ok, let me see if i understand u correctly, your specs give me no new questions they look ok. U have WM5 and want to run a program (from your work) which needs WM6 (wont run on WM5). HTC told you about the official WM6 update. This wont flash as activesync crashes, right?
With an official Rom you will not need to unlock the CID/SPL with USPL. But this goes only when you stick to your current language. i.e. a german WM5 is not allowed to be flashed into english. To do this you will need to USPL-unlock it 1st.
If the language is the same, it should work. Best is to do a hard reset 1st (2 soft buttons and soft reset, wait and press green/send.) Afterwards hook it on the PC (activesync want to start a newe partnership, click cancel, so u will be connected as guest).
Start the rom upgrade. Activesync should close and bootloader on the ppc will be started. This is a screen with many colours/stripes, which is normal but looks very bad and different from normal bootup.
Then the flashing will start, the screen on the ppc will turn white/grey and a scale will show you the percentage of the flashingprocess (similar to the screen of the pc). Wait patentiently and do not toch the ppc or disconnect (or expect a bricked device).
At the end, the ppc will reboot and take a while (longer then normal bootup) to initiate the boot for the 1st time.
If this wont work, then try to extract the upload file, put the ppc in boatloader mode, connect to pc and start the romupdateutility.exe directly.
Good Luck!
hi,
i've flashed my HTC P3300 and it was done successfully (using USPL) but the language was Spanish, i searched a lot how to change it to english since i dont understand a word of it.
through one of the forums, i was told to set the SysLang = 1032 in registry to get the english language, i done so, now, the phone is stuck in Welcome (WM6.1) screen and nothing is happening, not even responding to power key.
I tried hard reset, it doesn't work, i tried entering to bootloader, it also doesn't work, also, i am not able to connect it to PC since i guess its not completed up.
Just got stuck with a brick, can you help please. Really needed!!!!!!
Thanks
Maybe flashing ROM from memory card may help. Search Artemis wiki for micro card ROM flashing.
Hello, I guess I'm having the same problem...tried to flash but something went wong and now I have my htc p3300 blocked with the multicolor screen. It does not work, so I don't understand how I could start flashing rom by memory card. Could you be a little bit more detailed? Thanks in advance

O2 XDA Zinc. Please, help!

Hello all!
I've purchased O2 XDA Zinc in Arabian. I'm living in Russia now.
When I open the box, get the PDA and turn them on I've got screen like this:
mars II eboot ver......
h/w version v1.4
******** usb loader ***********
diskonchip g4 128mb
start downloading image...
please plug-in usb cable...
And that's all... Now I can't go to Arabian to change my PDA and there is no service center that can fix it in Russia
I tried soft and hard reset and no effect.
When I connect PDA to PC the new hardware "Asus USB sync" appear in system, but Active Sync does not recognise them (I have 4.5 version).
All o2 zinc upgrade software are working with active sync and available os and i can't use them.
I've extracted binary filles from update exe, larger of it i've rename to MarsII_G4.ABI and put it on SD. But after insterting card and restarting nothing happens.
I also have some knowledge of elelectronic.
So, please help, how can I fix my PDA?
Thank you in advise!
ok fer
find another ppc first
find a dos app and rename it to devicespy.exe and make it readonly
transfer it to windows directory of other ppc and plug it to pc via mini usb and activesync 4.5
download and run any zinc rom from seeo2
if you did it well the upgrade software cant recognize the device type so continue update progres until your ppc get reset.
replace that ppc with your zinc and update will continue to end and your zinc will be fin.
choose any lang you wish.
You'd better visit www.seeO2.com
and register with your IMEI.
Then you can download WM5 or WM6 official rom.
Hope this can help
Yeaaa!!
It's really working!!
Thank you!
I've recovered my device by using this method.
O2 XDA Zinc. Please, help
Hi where can I get dos app file??
hi all......
i do really need help for reviving my dead o2 zinc.
it is suddenly dead wen connected to notebook via activesync.
yes.. it is SUDDENLY DEAD.
i'm doing nothing.
i have been trying to entering bootloader (by pressing right d-pad plus soft reset), but the bootloader doesn't show up.
doing hard reset, but nothing happen. still dead.
one thing that works is...
there is blinking orange LED when i connected zinc with wall charger (without battery inserted)
and there is orange LED (showing up about 3-5 secs) when i connected zinc with wall charger (with battery inserted)
anyone can help me solving this?
how bout using mtty?
anyone knows?

Categories

Resources