After using the Witeless modem for a while...
I receive the message COM OPEN ERROR... (when oushing the start..).
Any suggestion?, It happend several times and so far my only way to recover is Hard Rest...
JasJar wireless modem
Suspected that com port was ocupied by the GPS, I deleted the GPS (releaseed com8) and the Wireless modem is working.
It seems that the wireless modem is using the avaiable port (com8).
From the other hand after deleting the pairing of the GPS, Destinator (since it has been fixed to com8) does not work, gets stuck while trying to access the GPS.
Related
since installing radio 1.13 i have not been able to connect to GPRS using wap.voicestream.com. this is after a hard reset with none of the EXT rom tools loaded. i try to connect, and it times out. in 1.12 i would be able to connect once but after connecting to activesync or disconnecting GPRS i was not able to log back in unless i soft reset or turned on flight mode then turned it off. I have 1.40 ROM installed with phone alarm 1.21, pocket plus, and wisbar 2.4.11
UPDATE!!!
ok, i uninstalled pocket contacts 1.1 from www.pocketx.net and installed pocket conctacts PRO 3.0. i also unloaded mort ring. well when i did that i was not only able to connect to gprs, i am now able to RECONNECT when i disconnect! wierd...
What device do you have and what ROM are you running? I'm looking to solve this problem on my PDA2K.
i have the same device and ROM as you do. since i last posted. i am only able to connect to GPRS after a soft reset, not turning on/off flight mode
Downgrading Caller ID to IA_CallerID_1.20_WWE.CAB will fix this problem. It worked on mine at least...
downloading and installing the cab for the caller_id worked for mine as well. i've had no problems with gprs connections since performing the downgrade -- which was a little over a week ago. i think you can find the cab in these forums if you search for it.
i dont have that caller id sodtware installed at all and i still have the gprs reconnect issue
Hi
Does anyone know how to setup IGuidance to work with WM5? I dont know how to work the BT ports at all. In 2003se, i could use the "scan" for bt data and it'd find the itrek gps unit but now it results in "no gps found". alternatively, what other gps software will work other than tomtom? I dont have tomtom =(
I've got version 2.1 and it seems to work with WM5. I add the gps to the bluetooth and then I create an incoming and outgoing port. I set my gps to port 6. In IGuidance it won't detect the gps but if you manually choose port 6 it will work just fine.
Andy
iGuidance 2.1.3 locks up my Wizard after several minutes. Grrr...
I am having all sorts of trouble with my PDA2K (WM5) and iGuidance. Although I think it has more to do with my bluetooth than anything. When I first started trying to get it to work it gave me coordinates that I was in Africa... Anyway, I think I am going to go back to 2003SE.
I'm having a different problem with iGuidance v2.1.3 on WM5. It installs and runs just fine. I use BT over COM6 and it seems fine. The problem I have is that the coordinates are off. The strange thing is that when I run GPSInfo (a separate app) it shows the correct coordinates - iGudiance thinks they are different and thinks I'm in a different location ( a few miles away).
I gave up on it and decided to go back to 2003SE (iGuidace v2.1 that worked perfectly fine on that configuration a long time ago). I followed teh steps to format/clean hive and did the down grade but am having a different problem. I've seen other people running into similar issues but I've not been able to get around it
"BTTrayCE - bluetooth can no longer be used because the license has expired" - I have tried a number of things using different BT stacks, 2003SE builds, reset (soft+hard) etc. Same problem!!! Argh - I'm stuck. I really miss my GPS!
Hi krille,
I also had similar problems with my SX66 and iGuidance and finally decided to go back to win 2003 because it worked fine with it. In WM5 my BT GPS receiver was never able to make a connection with iGuidance. But now I am having a different problem. I cannot downgrade even though I followed all the instructions correctly posted on the BA_Downgrade page. The upgrade program ( MaUpgradeUt_noID.exe ) does not seem to identify the rom versions and though it gives me a successfully upgraded message nothing had happened. I cannot downgrade now and stuck with WM5. Did any of you experience this when downgrading and can offer me any help.
DEK.
I've been upgrading/downgrading with differnt ROMs without any problems
Make sure to disable activesync on the pc and copy the nbf files as described in http://wiki.xda-developers.com/index.php?pagename=BA_Downgrade_WM5. Sometimes the verion info update to/from doesn't show between WM5/2003SE...
What happens when you click Update to continue?
BaUpgradeUt.exe worked
Thanks for your reply. I followed all the steps as described in the link you have sent but MaUpgradeUt_noID.exe did not upgrade (downgrade to 2003SE) though I got a message saying it did. Then I tried the file BaUpgradeUt.exe in PH20B folder and it did work. My device data file says my SX66 is in fact PH20B1 though. I do not know why MaUpgradeUt_noID.exe cannot update my ROM. Anyway I am happy now with my WM2003SE and iGuidance and BT all work faster with ROM update to 1.40. Now I am planing to customize my ExtROM to have all my personal settings and programs so that I want feel bad not having WM2005. Thanks for your willingness to help.
DEK.
topic sais it all. my GPS doesn't work anymore. and if i try to start COM3 with the taskmanager i get a error message.
maybe some1 could post me the 4 original GPS dll and i try to restore those, then it maybe works.
or you have another idea maybe?
mine starts on COM4
no, thats the option for programs to interact. there are special taskmanager programs that let you see the hardware of your pda and start/stop it.
P3300 gps has two ports: GPD0 and COM3... and i can't start the com3 (com4 is started btw)
Well, nobody seems to have GPS on com3 , you probably loaded a cooked ROM If no change on registry were made, your com4 IS the GPS com port.
If you want to use more com port or split your GPS com port, you probably want to use GPSGate.
zandadoum said:
no, thats the option for programs to interact. there are special taskmanager programs that let you see the hardware of your pda and start/stop it.
P3300 gps has two ports: GPD0 and COM3... and i can't start the com3 (com4 is started btw)
Click to expand...
Click to collapse
TO restore original files you can do an hard reset, otherwise you can try to delete the four dlls and they will be restored from the original rom.
i ended up doing a hard reset
Hi
I have (had) a Dutch version of HTC Diamond from Vodafone and flushed it with official 1.93 HTC WWE ROM. The problem is, the original Vodafone ROM came with Tomtom 7 which is not included in HTC ROM.
Tomtom is still on the internal storage and I can run it. However, no matter what I do it doesn't get the signal. It keep showing "waiting for GPS signal"... My theory is, something is missing in Tomtom to function propery.
Has anybody extracted Tomtom CAB installer from a "custom provider" rom, so I can re-install it? Or, may be there is something else I could to to get it to work?
Thanks in advance!
Please don't post this in the development section...
There are enough CAB's (legal) on XDA if you search.
Did you also flash the radio? If not, try a different radio.
Make sure your settings for External GPS are like this:
Programs
GPS Program Port > COM4
Hardware
GPS Hardware port > none
Baud rate > 4800
Access
Manage GPS Auto > CHECKED
Also be sure to set TomTom to Internal GPS or Other GPS (No BT or TT device).
Thank you!
(This is my last post on the subject, I understand that this it the wrong forum)
Just for the record: Tomtom "sees" the GPS unit (it turns from "No GPS Receiver" to "Waiting signal" quickly). My Radio ROM is xx.xx.25.05.
Ok, I will do more searching.
That's actually how it should work. It takes some time to find the build in GPS. After this it searches for a signal. You might wanna test this outside since it's hard to get a fix inside depending on your location.
Sometimes it takes several minutes to get a fix.
Concerning flashing. I always perform a few hard resets after flashing. Might wanna try this. If all fails reflash the radio ROM
its a setting in tomtom... try changing where it gets it gps signal from....should be set to internal gps...
That's what I said But according to the TS it "sees" the actual GPS but it's got no signal..
update quickgps.. go to somewhere without trees etc.. you should get a signal.. wait for it for a while.. if still no luck.. update your radio to. 07
sorry bro.... didnt read that bit..my bad.
np mate it's late (2:00 am).
The radio should work just fine, I use the 05 all the time.
Holland isn't that big but you can always try the 07 (or 08 for that matter) of course.
Thanks for all the replies!
I, of course, did the hardreset after flashing the rom and ran QuickGPS update.
When in Tomtom, I can go to the "Satellites" and I can see that Tomtom get's poor signal from 2-5 satellites at the time. I was outside for 40 minutes, couldn't get a lock. May be something wrong with my device :-(
Try setting "other nmea receiver"
when you 'flushed' it with the offical HTC rom your radio got updated...
i flashed the official HK rom and noticed the radio rom being updated also...
try a different radio file...
i can tell you it makes a huge difference!
.08 works best for me with regards to gps lag but takes 5-10mins to sync...
so i'm using .06
Hi TT7 on diamond works ok,
set tt to internal GPS. close TT.
run quickgps fix , start TT again.
now TT wil find its gps-ses lots faster.
Im running AZTOR V6, radio .08
( Tmobile .NL )
I recently change my BB for a Tilt 2 but I haven't figure out how to use it as a dial up modem as I did with my BB are there any software or driver available for vista 64
Ive downloaded some driver but no luck!! any help will be apreciated!
internet search please:
http://forum.xda-developers.com/showthread.php?t=338003
I'm trying to use the phone as a dial up modem those instruction are for data sync any other suggestion
Welcome to forums
Have a deep read here:
http://forum.xda-developers.com/showthread.php?t=407563
Read, Search, Respect and Enjoy!
Well after reading the last thread I'm still having problems my notebook doesn't recognize the phone as a standard modem I've installed various vista drivers found on other threads still no luck!!
os windows vista 64
im using vista64. it shouldnt matter which version you are using because drivers are automatically installed when you connect via usb. when i first plugged in my tp2, it automatically set everything up. dont try to configure the modem crap in MyComputer, but rather just hook up via the internet sharing app on the tp2 or if your laptop supports wifi, enable wifi on your tp2 and search for the signal on your laptop. the above mentioned forum topics should have more than helped. its easier than you make it bro. btw, are your carrier internet settings correct? here are settings for Tmobile and ATT. hope this helps.
For sure give this thread a read: Wifi Internet Sharing
It's the easiest way to turn your phone into a router and get internet on your laptop. That said, if your laptop or desktop isnt wifi enabled then you'll just have to teather it using "internet sharing" I havn't seen a rom yet (even my stock ATT rom had it I believe) that doesn't have internet sharing built into it as a standard option in the com manager or in the connections settings.
if you dont have the internet sharing app, its HERE in this thread
This most be very disappointing for all of you that have tried to help me on this issue but I'm still having problems...
List of things tried already
1. Installed internet sharing but cant get the phone to connect via usb, the wifi recieve data I've tried the phone on my home network without sim card and it browses the net without problems but can't use it as a router with or without the sim card
2. Follow the att instructions but my phone has the media net setting locked and I can't edit them
"Media Net This connection is pre configure. It cannot be modify'
3. installed all kind of drivers still not recognized as a standard modem
Last drivers instaled was using wmdriverinstaler
Even gone to you tube!!
Toshiba satellite a305 wifi enabled
vista home premiun 64
att tilt 2 rom1.59.502.3 rom date 9/25/09 wm6.5
CE OS 5.2.21849 build 21849.5.0.63
att $30 unlimited data plan ("no thethering" din't need it with the blackberry since it work as a dial up modem)
I wont give up I like this htc better than my BB curve!!!
Is it a rom issue?
Drivers issue?
att plan that has to upgragded to tehter "won't go there"
Unlocking the phone?
Thanks!!
Have you tried connecting the laptop to the phone via Bluetooth (if you have that option on your laptop)? I was trying to get Internet Sharing going this way, and once I paired the two, I got an option to use the phone as a dial-up modem, rather than just sharing the phone's ATT data connection (which sounds like exactly what you are looking for). For some reason, I got this option when I connected via Bluetooth, and not USB. Also, I'm using XP, and not Vista, so I don't know if that will change the options.
quiquerc said:
This most be very disappointing for all of you that have tried to help me on this issue but I'm still having problems...
List of things tried already
1. Installed internet sharing but cant get the phone to connect via usb, the wifi recieve data I've tried the phone on my home network without sim card and it browses the net without problems but can't use it as a router with or without the sim card
2. Follow the att instructions but my phone has the media net setting locked and I can't edit them
"Media Net This connection is pre configure. It cannot be modify'
3. installed all kind of drivers still not recognized as a standard modem
Last drivers instaled was using wmdriverinstaler
Even gone to you tube!!
Toshiba satellite a305 wifi enabled
vista home premiun 64
att tilt 2 rom1.59.502.3 rom date 9/25/09 wm6.5
CE OS 5.2.21849 build 21849.5.0.63
att $30 unlimited data plan ("no thethering" din't need it with the blackberry since it work as a dial up modem)
I wont give up I like this htc better than my BB curve!!!
Is it a rom issue?
Drivers issue?
att plan that has to upgragded to tehter "won't go there"
Unlocking the phone?
Thanks!!
Click to expand...
Click to collapse
which rom are you using?
ok so if you are using the stock rom, why cant you connect? your settings are automatically set up on a stock rom. you must have done something in the connections settings to screw up your connection. just reflash the stock rom.
Well thanks for all the help and suggestions but the problem was the actual phone
I went to ATT and changed the unit and now it works fine I was able to connect via internet sharing using wifi apparently there was hardware failure with my original tilt
Thanks you for all your help!!!