I was unlocking my AT&T SX56 and the rom upgrade just stoped and I could not do anything to mak eit start up again. Now The pocket PC has upgrading rom always on the screen and I can gt active sync to even see the pc to try and flash it or upgrade the rom again. If you have any info you think that might help would be great. Thank you for your help.
If you still can get to the bootloader screen (power + soft reset), you can cook a new ROM as nbf file and use the SD flashing method.
Cool man I can get to that screen and will give that a go
Ok got a SD card and put on a new rom how can I make it load the info from th card. Also everytime I try and make a nbf file type it erros on me.
./mkrom.sh: ../../kitchen.local/mkrom-inc.sh: No such file or directoryno files for configid 26220739write xip block starting at 81800000, with 3 fileswrite xip block starting at 81980000, with 0 filesheader : No such file or directoryError creating new rom
I picked nb1 said was for flashing with SD card and can't get it to load.
Hi,
i have problem with my PDA (Qtek 1010), once i reset ,it is not working, it shows the message "This ROM was cooked in the XDA-developere.com ROM kitchen cooked to order.to suit your demanding taste" & stopped on this screen only,i tried lot of time, but still the same prblm . so plz, can u assist , how to over come frm this prblm.
thnking u
What have you actually tried so far? Have you reflashed it with another ROM/the original ROM?
HI plz do need full
Complete scene what happen:
I m trying to connect using IR to laptop, that time it
hangup, so I made soft reset. After I made reset It will not start,
thn I tried lot of time soft and hard reset, It will showing only
initial screen " This ROM was cooked in the xda-developers.com ROM
Kitchen cooked....." and stopped here only. It is not loading the
operating system. So please do need full. I ill grateful for u.
Now also i tried These below Step ,
How to Flash your Device using bootloader and SD-Card....
1. Download XDATools
ftp://xda:[email protected]/Wallaby/Tools/XDATools.zip
2. Extract them at any place and run osimagetool
3. Select your Rom Image from the Source drop down menu.
4. Select your SD card (disk drive) from Destination the drop down menu.
5. Select Copy to start writing process and the tool should start writing to
the card.
6. When XDATools has finished writing the image (no Infomessage) put the
SD-card into your device
7. If there comes a message to format the SD-card select No
8.
Hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
9. Press action to download and it will start the download/restore from the
SD card.
10. Follow the on screen instructions once its "Completed" which will consist
of a " Hard Reset"
You can get an original ROM here:
ftp://xda:[email protected]/Wallaby/ROM/
Or cook your own at http://lumpistefan.dyndns.org
Since the ROMs are a exe fiel, you have to extract the exe file using winzip.
You get a folder english containig the ROM NK.nbf with about 32 MB....
You can use all ROM's excpet the WM2003SE
But now i m getting the error " After complete, I made hard reset, its on first screen as "Test Only Not for Sale, Microsoft Windows powered" message with version details and stopped here only. It is not moving ahead. So plz can u instruct further wht to do
Thanks & Regards
kAreem khan
System Engg.
My P535, 71A version. upgrade WM6 HK version from 4.3.25 HK00.
I used a 256MB miniSD with quick formatted( it's the main reason). extract the upgrade file on it. and start the upgrade procedure.
1st step: insert the miniSD into slot. autorun started and asked to confirm. sure. confirm it.
2nd step: system starting upgrade the bootloader, read, verify, and update ok. it ask to reset with power button pressed. do as requested.
Like attachment 111.jpg
3rd step: the bootloader entered a new uploader version with "force mode" displayed. and loading the main upgrade file ASUSP535.CAP. but checksum failed. it it asked to reset with power button pressed again. do as requested.
Like attachment 222.jpg , I failed at checksum because the miniSD only quickformatted
then the nightmare came. I can't see the blue asus screen. and nothing happen when I press reset. the only valid operations are Power+Camera+Recorder + reset to the SD download mode, and Power+Camera + reset to the USB sync mode. in the SD download mode. system not recognize the *.cap file. it request a NB0 file.
What should I do?
1. Enter the Force mode again with a good formatted miniSD is the best way. but how?
2. Use the USB sync mode upgrade the file, it maybe works. but I can't find the usbloader. in my memory. there is one in the lifeforce cooked ROM pack. but it removed when I visit lifeforce's site today. anyone who download the rom pack before please give me the file. I need a try.
-------------------------updated on 9th Jul 2007---------------------------------------
My P535 has been recovered.
just use a modfied 4.3.25 HK00 NB0 file at the SD download mode, it can reverse to WM5, then repair the extend firm. don't reset, direct run 4.3.25 offical update. switch to another sd card with WM6 upgrade ASUSP535.CAP when it reboot to the sd download update screen. and all will go on.
find an old rom on asus ftp or site.
Rename the rom to galaxyII.nb0
Copy it to the card.
Boot your phone with the card in SD download mode.
The upgrade will start.
Good luck.
For me after the autorun, i pressed ok to restart but the phone still block at the blue screen. I try to reset in sd loader with the new rom in sd, with the galaxy name, and the rom is to big for the phone...
ilan_75 said:
find an old rom on asus ftp or site.
Rename the rom to galaxyII.nb0
Copy it to the card.
Boot your phone with the card in SD download mode.
The upgrade will start.
Good luck.
For me after the autorun, i pressed ok to restart but the phone still block at the blue screen. I try to reset in sd loader with the new rom in sd, with the galaxy name, and the rom is to big for the phone...
Click to expand...
Click to collapse
I had tried as you said. put 4.3.25 HK CAP file on the minSD, and rename it with NB0, but it not work, it return red words with" Wrong Language Version, Update fail!" the system is the HK before update WM6
You may try try here...
http://www.asuspda.net/thread-17850-1-1.html
but not sure does it 100% work...
Good Luck!
Hello,
I've attached the requested tool - and... good luck
A_C said:
You may try try here...
http://www.asuspda.net/thread-17850-1-1.html
but not sure does it 100% work...
Good Luck!
Click to expand...
Click to collapse
thanks, but that's not what I need, because I can't enter the OS already...
windirt said:
thanks, but that's not what I need, because I can't enter the OS already...
Click to expand...
Click to collapse
It is picked from that archive...
lukacs.attila said:
Hello,
I've attached the requested tool - and... good luck
Click to expand...
Click to collapse
sigh... I tried with usb sync, the 79MB cap file can't transfer completely. it just transfered 55MB and stopped.
windirt said:
sigh... I tried with usb sync, the 79MB cap file can't transfer completely. it just transfered 55MB and stopped.
Click to expand...
Click to collapse
I have no idea, but maybe it is because you already upgraded the bootloader?
lukacs.attila said:
I have no idea, but maybe it is because you already upgraded the bootloader?
Click to expand...
Click to collapse
Yes. the first upgrade step is completed, the bootloader version is changed to 2007/04/16.
when I press Power+Rec+UP and reset, it got a Force mode USB Sync. not like the ordinary USB Sync enabled by Power+Rec and reset.
is there a way to get a Force mode with SD Download? so I can use the 79MB CAP if it accessable.
windirt said:
Yes. the first upgrade step is completed, the bootloader version is changed to 2007/04/16.
when I press Power+Rec+UP and reset, it got a Force mode USB Sync. not like the ordinary USB Sync enabled by Power+Rec and reset.
is there a way to get a Force mode with SD Download? so I can use the 79MB CAP if it accessable.
Click to expand...
Click to collapse
Correct me if I am wrong, but there's something written @ asus support site, where you can download the new firmware (it's a step by step how-to). Unfortunately, the support site is down at the moment.
Please follow the below procedures to upgrade:
1.Please format your Mini-SD first.
2.Unzip the file and copy it to Mini-SD card's root folder
(Under Mini-SD's root folder, there should only be folder 2577, AsusP535.cap, and GalaxyII.cap;
In folder 2577, there should only be Autorun.exe).
3.Insert the Mini-SD with upgrade firmware into P535's expansion slot and wait for firmware to setup automatically.
If the firmware didn't execute automatically, please execute Autorun.exe in Storage Card\2577\.
4.Click "System" => "Update ROM"
5.System will enter update mode, here the first part of upgrade will start.
Warningo not interrupt the upgrade process. Please execute the rest of the steps until completing step 8 in order
for the unit to execute normally. After the upgrade is complete, a message in red will be displayed.
Please press and hold power button and reset at the same time to start second part of upgrade.
6.After reboot, it will automatically enter update mode. This upgrade takes about 3 mins, please wait patiently.
Please do not interrupt the upgrade process. After upgrade is done, system will reboot automatically.
7.After reboot, it will install extended ROM automatically. After upgrade is done, system will reboot automatically.
8.Please Confirm version in "Start"=>"Setting"=>"System"=>"System Information"=>"Version".
lukacs.attila said:
Please follow the below procedures to upgrade:
1.Please format your Mini-SD first.
2.Unzip the file and copy it to Mini-SD card's root folder
(Under Mini-SD's root folder, there should only be folder 2577, AsusP535.cap, and GalaxyII.cap;
In folder 2577, there should only be Autorun.exe).
3.Insert the Mini-SD with upgrade firmware into P535's expansion slot and wait for firmware to setup automatically.
If the firmware didn't execute automatically, please execute Autorun.exe in Storage Card\2577\.
4.Click "System" => "Update ROM"
5.System will enter update mode, here the first part of upgrade will start.
Warningo not interrupt the upgrade process. Please execute the rest of the steps until completing step 8 in order
for the unit to execute normally. After the upgrade is complete, a message in red will be displayed.
Please press and hold power button and reset at the same time to start second part of upgrade.
6.After reboot, it will automatically enter update mode. This upgrade takes about 3 mins, please wait patiently.
Please do not interrupt the upgrade process. After upgrade is done, system will reboot automatically.
7.After reboot, it will install extended ROM automatically. After upgrade is done, system will reboot automatically.
8.Please Confirm version in "Start"=>"Setting"=>"System"=>"System Information"=>"Version".
Click to expand...
Click to collapse
Yes, it stopped in step6 as you posted, checksum error.
Upgrade WM6 critical problem
I was trying to upgrade my ASUS P535 rom from V4.3.15 WWWEL_RU to firmware V4.7.12 WWE_TH00
I unzipped the P535_V4712_WWE_TH00_EXT_V120 and copied the files produced to the miniSD card except from file AsusP535.cap
I renamed file GALAXYII.cap to GALAXY.cap and copied it again to miniSD card. Also I copied file ASUS.UnlockLangID to folder 2577 and replaced autorun. (P535 ROM Tools.zip from http://forum.xda-developers.com/showthread.php?t=295778&page=3)
So in miniSD card there are the following files: 2577 folder with autorun and unlocklangid.exe, and in the root, GalaxyII.cap and GALAXY.cap but NOT AsusP535.cap
So I run the update and after the reset I get message ASUSP35.CAP NOT FOUND.
At that point I realise my stupidity (not copying AsusP535.cap to miniSD) so I take the card out, put it in my laptop and copy the AsusP535.cap to mini SD.
I reset the device and stick the card in but I still get the same message ASUSP35.CAP NOT FOUND.
Every time I turn on my device it tries to upgrade rom and I get the mesage. Can someone help please or have I damaged the device beyond repair?
2 mins ago I upgraded my taiwanese p535 to the thailand wm6 rom.
I had already installed a 4.3.15 wwe version, so I figured I could just install the 4.7.12 wwe TH rom without using the "hacked autoexec".
That didn't work, and I was stuck with the blue asus screen.
So I pushed up (on the d-pad) + reset, then "green phone button" (answer button) when it asked if I wanted to.
then reset the phone as soon as it said "performing upgrade" or something like that (when it started installing stuff after windows was booted).
After reboot, I was back at my old 4.3.15 rom.
Then I decided to retry it, following the instructions here:
http://forum.xda-developers.com/showpost.php?p=1352033&postcount=77
(the link to the p525 tools is incorrect. It should be: http://rapidshare.com/files/4612627/ASUS_P525_v3.32.WWE.customized.build.06.zip.html
Edit: The link to the thai wwe rom is incorrect too, it should be: http://dlsvr01.asus.com/pub/ASUS/IA/P535/P535_V4712_WWE_TH00_EXT_V120.rar)
When I followed these instructions the upgrade worked perfectly. I now have 4.7.12 wwe_au00 installed
I can't give any guarantees, And it may be that I was just lucky, but I suggest you try to remove the miniSD, then push up+reset, press "answer button" when it wants you to confirm, and then, after it reboots, press the reset button as soon as it starts the "upgrade". Then (I hope) it will revert back to your previously installed OS.
After that, upgrade to wm6 following the procedure in the link I pasted above.
extract nb0 from cap for asus p535:
wm5:
xda2nbftool.exe -x galaxyII.cap galaxy2.nba 0xA87BC0d5
wm6:
xda2nbftool.exe -x asusp535.cap asusp535.nba 0xa87ba0d5
.nba from .nb0 seems differs for 4 bytes
.nba - first 4 bytes = .nb0
(check it /in device upgrade may be significant - don't knew (i'm use other device)/ )
.nba, .nb0 - standard files as for oher devices - can make modified firmware images as for other ...
I can't give any guarantees, And it may be that I was just lucky, but I suggest you try to remove the miniSD, then push up+reset, press "answer button" when it wants you to confirm, and then, after it reboots, press the reset button as soon as it starts the "upgrade". Then (I hope) it will revert back to your previously installed OS.
After that, upgrade to wm6 following the procedure in the link I pasted above.[/QUOTE]
Unfortunately, when I press up+reset I dont get the option to confirm, it just goes immediately to the same message ASUSP35.CAP NOT FOUND
DaLiV said:
extract nb0 from cap for asus p535:
wm5:
xda2nbftool.exe -x galaxyII.cap galaxy2.nba 0xA87BC0d5
wm6:
xda2nbftool.exe -x asusp535.cap asusp535.nba 0xa87ba0d5
.nba from .nb0 seems differs for 4 bytes
.nba - first 4 bytes = .nb0
(check it /in device upgrade may be significant - don't knew (i'm use other device)/ )
.nba, .nb0 - standard files as for oher devices - can make modified firmware images as for other ...
Click to expand...
Click to collapse
I am sorry but I dont understand the solution you are suggesting
Could you please explain?
ntiouk said:
Unfortunately, when I press up+reset I dont get the option to confirm, it just goes immediately to the same message ASUSP35.CAP NOT FOUND
Click to expand...
Click to collapse
Hold the up button, then press reset while still holding the up button.
are you sure it says "ASUSP35.CAP"?
It doesn't say "ASUSP535.CAP"?
.nb0 - it's another way t program device
press photo + reset - that asks file - resulted .nb0 file for wm5 or wm6 name as device wants - write that to sd (not sdhc) card formatted as fat16 - and insert it to device.
When i download the USPL_2.28.0000_with_IPL_2.27 it comes with a folder named RUU.
The folder of the ROM (Onyx Ultimate 4.0) i choosen to flash comes too with a RUU folder.
Flashing SPL proccess:
************************************************** ***********
Please make sure Activesync is enabled (green icon in systray)
and hit ENTER to start...
STEP 1/3......50%......75%....100%
The next step will load a patched bootloader (SPL) on your device
it will make your device temporary SuperCID (seclevel=0), and will
avoid modelID and signature checking when flashing NBH files.
Hit ENTER to continue...
STEP 2/3.....15%.....25%...50%...75%.....100%
Phone screen should now be blank and the activesync icon gray
if not, the loading procedure has failed and you'll have to repeat again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash patched SPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash the patched SPL, when this
step completes your device will reboot.
STEP 3/3 - Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate
************************************************** ***********
(c)2007 pof - XDA Developers
Hit ENTER to quit.
---------------------------------------------------------------------------
My question about this proccess is in step 3, when is saying "Launching RUU".
What RUU is this? Do i need to complete this RUU and then execute the RUU for Onyx? Is there 2 RUU happening to a successful flashing?
I saw in a site this tutorial:
1) Extract the USPL files to a folder, keep this window open.
2) Connect the Orbit to your PC (or laptop).
3) Once you have the Green ActiveSync icon, run start_uspl.exe, in your open folder from 1).
4) The start_uspl program opens in it's own DOS window. When the progress indicator reaches 100, 2 things will happen.
- ActiveSync will disconnect (you should also hear the 'USB Disconnect/reconnect' sound on your desktop), and
- The orbit screen will go blank (mine goes black, some go white)
Don't let this put you off, and continue undeterred, you're nearly there. Also, don't be tempted to disconnect anything, or reset your device.
5) Return to your extracted files window from 1), run ROMUpdateUtility.exe.
6) Follow the instructions in the three screens to start the update, which should take about a minute (not 10 as the screen suggests).
7) Once you get the "Congratulations" screen, the USPL phase is complete
--------------------------------------------------------------------------
What i can see from here is that i will complete the RUU from the SPL and then execute again another RUU thats comes in the Onyx folder. Right?
Sorry for the lammes questions
(I've already posted this in another area of the forum, didn't know what's the best one to post)
Dear All,
hi i was upgrading my p3300 rom its almost 90% done but my pc suddenly shutdown now my p3300 hang on startup screen i was try to flash with MMC but its also hang on tri-colours plz plzzzzzzzzzzz give me solution &
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM
Faraz
1. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer or format it from your computer using a card reader, make sure to format in FAT32 and not FAT although in some cases format doesn't work, also it is only necessary to format if your first attempt at flashing fails
2. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
3. Rename the .NBH file to ARTEIMG.nbh and copy it to the root folder of your microSD card.
4. With microSD card inserted on the phone, start the bootloader (The bootloader is invoked by pressing down the Power & Record buttons and using the stylus at the same time to press the RESET button at the left side), keep both buttons pressed after releasing the reset button.
5. You should see the screen pictured on the left, confirm flashing on screen by pressing the volume slider down.
6. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts. After the flashing process is complete, it will tell you to press any button to continue. After this the bootloader screen with its red/green/blue color is shown. Just reset the device and it will boot the new ROM.
SuperCID devices are able to flash any NBH image using this method.
Not working ??????? Its hang on tri-colours screen i was checked 5 hours
look up the original factory rom of your phone and flash it on your phone doing the normal way
i ill be very appreciated if u give me the link where i can find plzzzzzzzzz
N thx for reply
i ill be very appreciated if u give me the link where i can find plzzzzzzzzz
N thx for reply
link
http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
good luck