HEEEEEELLLLPPP!
I have managed to connect to my wireless router at home via my MDA3 but whenever I open IE and try and surf it responds by telling me that the page isnt available. ie. it cannot surf the net!
As soon as I put the MDA3 into the cradle it works fine. I know these are two different ways of connecting to a network but how do you surf the net via WiFi to your home wireless network?
Hello meatychi,
Try connecting the MDA3 as the only device on the router. You may have to switch off other devices first and reboot the router.
I have this problem too, and i can NOT use my pda2k and the Fujitsu laptop at the same time on the wireless router. It will work if the laptop is hooked up via cable and the pda2k is on wireless, but never together.
I returned the router to the shop and we tested it there. It all worked as it should with their wireless equipment, which leads me to believe that the wireless components in my Fujitsu laptop interfere somehow.
Let me know how you go.
Regards,
Atze.
Interesting!
The only other device I have on wireless is my mac and that wasnt on when trying to get the MDA to work.
Did you use a static IP or DHCP?
Could you give a little more detail into the way you setup your PDA to communicate with your wireless router?
Initially I used DHCP, when that didn't work I switched to static IPs
which didn't help either. I even throttled the router back to 802.11b, as I thought that the two different protocols may be in a tangle, but... you guessed it. No luck.
After all this I reverted back to DHCP and switched the router back to 802.11b+802.11g. The laptop is back on a cable
Everytime I try something with both devices hooked wireless I have to restart the router, as it will no longer work with either device.
I have set up the pda2k as follows:
Connect to Work network,
Using WPA-PSK authentication
TKIP Data Encryption
It is set to access All Available networks,
Automatically connect to non-preferred networks
Use server-assigned IP address
Leave DNSs and WINSs blank
Performance is usually set to Best Battery, but I vary that when I go downstairs. (doesn't appear to improve the range thoug I think it's pretty poor.)
Auto turn of WLAN if not connected is ticked to kick in after 2 minutes.
Regards,
Atze.
Thanks for the info I will try again tonight!
i'LL LET YOU KNOW HOW i GET ON!
Related
Hard to believe !
I just got back home and tried to connect my new Blue Angel to my Wifi network and... and... and... it seems that there is no way to connect to an AP not broadcasting the SSID !!!
Can someone confirm this? Why such a restriction? Any workaround (besides broadcasting the SSID) ?
My previous PDA did not have this problem !
Thanks.
You are correct. This does not work with the current driver version (at least the one that shipped with my MDAIII in Germany).
Even if you connect to the AP with the SSID broadcasting and set-up WEP, the link will not be re-established when the SSID broadcast is subsequently turned off on the AP.
I also found that even when SSID BC was on, the MDAIII required frequent resets when turning on Wifi and switching APS. Hopefully they'll supply an updated driver.
BTW: Connecting to non-broadcast SSID does work on an MDAII with a sandisk wifi card using the latest Socket driver (doesn't work with the Sandisk driver).
Cheers,
Martin
Well, it works on my new SPV M2000. My AP has an SSID set, but does not broadcast it. I had to type the correct SSID/WEP key, and it all just worked.
I can connect to my access point, even though it's not broadcasting it's SSID. I think the trick is to name your network the same as the SSID. After turning on WLAN, in the WLAN manager - click tools, then click new connection and name the connection your SSID, and then enter relevant WEP keys, etc.
Be warned that it seems the PDA2K has awful WiFi range, my connection rarely shows over 50%, even in the same room as my access point, and on the next floor of my house, the connection often drops - never had this problem with any laptops or other PPC devices.
@whydidnt and dbarfoot :
Okay, sorry about that. I could not find how to get to the place where you can see the active WLANs APs etc... Seems to work as it used to.
I'll disable again the broadcasting of SSID today to check if it works okay, but I don't expect a big surprise.
I was kind of worried if it really had not been supported properly
Thanks
Does anyone have a problem with their wifi locking up their xda iis? I have bought a linksys router and am getting frequent lockups when using wifi. I am using the shipped O2 rom, thanks
I have no problem at all with Netgear router. Try changing the connection speed setting in the router to the "b" mode only. Hopefully this can solve your problem.
No problems here either I'm afraid. I'm using a Draytek Vigor 2600VG at home and at work there are two of us with XDA IIs using a Linksys BEFDSR41W wireless router and no problems there either.
Sorry! :-(
Try a hard reset (gulp!) and see if you still have problems (Without anything else installed that might be inteferring) otherwise might be a faulty unit perhaps.
--Neil
I second what xanth said, I had the problem where wifi would not turn on, so I hard reset and installed each software back individually the problem was Calligrapher 7.3 did not like being in Storage or Storage Card only in Main memory (go figure)
efjay said:
Does anyone have a problem with their wifi locking up their xda iis? I have bought a linksys router and am getting frequent lockups when using wifi. I am using the shipped O2 rom, thanks
Click to expand...
Click to collapse
I use the XDA IIs on a variety of wireless networks and experience problems with an alarming regularity. The most annoying is the fact that the top bar seems to loose functionality, when using wireless!!
I will actually add that I do seem to have problem with the "range" of WiFi.
I need to do more testing, but it doesn't seem to be more than 20m or so before have communication issues/timing out :-( Will have to find out what our walls are made of!!!
I have problems connecting sometimes. I regularly use three routers, Draytek, Buffalo and Belkin. The only time that it locks up is when using skype. The skype problem is a known issue with no cure.
Nigel
I am having a problem where my Siemens SX66 will loose connection to my Microsoft MN700 wireless AP on occasion. -It simply appears as if the Wifi radio shuts itself off.
Weird.....
Wifi has never worked for me. It simply doesn't work in the way nature intended.
The main problem (as far as I can tell) seems to be that it cannot get DNS or IP configuration settings from my router (Belkin 7630) automatically.
It can connect to my wireless network without any hassle, but that's about it. If I enter DNS and IP settings manually it works fine. But this is unworkable if you want to connect to another wireless network.
If I can't sort this out by next week I'm going to sell the unit on eBay. It's been nothing but a pain since I mistakenly bought it in December.
Wifi is a nightmare on this device! I'm going back to Nokia.
I am going to do a hard reset and test to see if i still get any freezes. Anyone know of any software i can use to backup my text messages?
WiFi
Hi guys,
Haven't had too many issues with WiFi over here - standard O2 Asia ROM (with the BT 3500 update).
I'm running a Netgear WG602 @ home with 64bit WEP and a Dlink AP2100 @ work with WPA-PSK. No connectivity problems at either location, both DHCP. It does however take a few minutes to connect, but this is on the odd occasion.
The only frustrating thing with the WiFi is that I have to soft-reset often to turn Wi-Fi on - any ideas? Hopefully O2 will fix this in the next ROM. Other than that, I've had the Nokia 9500, P900/800 and this is by far the best device for the power user.
Just me 2c!
Cheers
cK
Wifi is on all the time on my device, sometimes when I switch the device on while within range of an AP it does not connect. Often switching wifi off and then onn again causes it to connect. If this does not work then I can often go into the network dialogue section, and see the network marked as 'availble' but not connected (why it sometimes does not auto connect I dont know). Tapping connect usually cures. If that does not work then I too need to soft reset.
I hope like you that they fix this cause its damned anoying. I will be interested to see what the Benq P50 is like when its released. I shall get one from expansys to test and ship it back within the 7 days.
Nigel
As for those having problems with specific access points. It is not nessesarily the fault of the blue angel. It seems to me that none of the manufacturers of wireless kit understand the term 'standard' they all seem to have their own take on it, which is why kit from different manufacturers refuses to talk to each other. I am of the opinion that they do it in purpose to lock you into using their client cards with their AP's !!
Try it with some non Belkin kit and see what happens.
Nigel
Well i tried a hard reset and didnt install any apps and tried connecting to wifi again and still got a lockup and loss of connectivity. Im going to swap the router for another make and see what happens
Swapped my linksys router for a D-Link and so far no problems after 2 days. so looks like my problem was my router.
Swapped my linksys router for a D-Link and so far no problems after 2 days. so looks like my problem was my router.
XDA IIi and wifi
I just bought one of these and can't get it connected. I have a netgear wg602 access point. When I finally figured out how to set the IP manually (the 02 xda tech support said it can't be done - maybe they're right ;-)
I now have it saying it's connected, with right IP address. My DNS and gateway are set up for the wireless adapter in network adapters. The signal is average. The XDA says wifi is connected. The access point even says it's authenticated and associated - same as my other stations.
Only problem is, internet explorer doesn't find any web pages - says "The page you are looking for cannot be found" (works fine through GPRS)
Also, terminal services times out trying to connect to an internal IP address (to eliminate DNS as a problem)
So, anyone know how I troubleshoot network problems - it looks like a TCP/IP issue? Can't find ping or arp etc. I've also tried an IP address that I know works on the network.
thanks for any help
Dave
Hi
For ping, ipconfig and stuff, head to http://www.cam.com/windowsce.html
I have had multiple issues trying to get wifi working reliably. It still fails now, but there are a few tricks to get it working again. Most of my wifi issues have been due to regular use of three AP's [email protected] and [email protected] along with GPRS and VPN.
To start with I suggest setting all the ****e in connections (internet and home network to 'My ISP' then goto your wifi setup, network adapters, and tell it that the wireless card connects to the internet. Now, tap ok, and goto tools, network cards, tap the active connection (it must already be connected) and ensure that its set to internet.
Next soft reset the thing, and wait for it to connect to yr wifi. Now, use the ipconfig tool and ping tool from the above site to check that all is OK. Check that its got the default gateway right and a sensible LAN IP.
I have found on occasion that I can be connected via wifi, but that the device is still trying to talk using an old IP allocated by gprs which means nothing to my lan! IPconfig will show if all is OK.
Whoever wrote the whole of the networking system (and its terrible gui's) on windows mobile wants shooting. I usually have 2 VPN profiles setup under my work network. If I leave it set to that, and use wifi from my lan to connect to the internet all is fine. However if I try and access a local server, the damned thing starts trying to connect a vpn (it aint inteligent enough to work out that the IP I asked it to connect to is local).
I have been trying to find a setting for all this networking rubbish that allows me to do *everything* without reconfiguring each time - to no avail.
Another thing to note is that you cant send/receive MMS messages while wifi is connected (more stupidity), it tries to connect to the MMS server using the wifi connection, and the telco blocks it cause it wants to charge you for sending MMS over GPRS. Only solution is to disconnect wifi, send MMS then reconnect wifi!!!
Nigel
No problems with WiFi for me
Hmm I'm using an O2 Asia Rom as well.. and my wifi manager seems to automatically create "settings" for each AP it detects and I seem to have no problems connecting at all... been using WiFi around my house since the first day i got it..
i am using a Linksys Wireless 802.11b router..
btw I am new here.. finally able to register!
How's everybody doing?
Cannot turn off IEEE 802.1x
Has anyone had problems unchecking the 'IEEE 802.1x netwrok access control' checkbox???
I uncheck it, but then when I go back to the screen (click on the connection | then select 802.1x tab at the bottom) it has checked itself again!
The XDA IIs does not save the setting - it just keeps re checking itself 02 help have been no use - they sent me an instruction manual and it even says in one of the step 'uncheck IEEE check box'
Im am using a netgear wirelesss router and have also tried on a d-link
Sugestions - is anyone else having this problem??
Hi guys, I recently destroyed my XDA2 and got a 2s on the insurance
Bluetooth on WM2003 SE if fair poor, but I managed to upgrade the stack thinger to 3900..... so I'm not completely XDA illiterate.
However, the wifi baffles me! I have access to an unsecured wireless network with internet access, and my 2s will connect to it. When I go on the the internet on my XDA, even with wifi connected it still tries to connect GPRS to use the internet. If I keep clicking cancel, it will load the page (presumably through the wireless network's internet access).
It has become clear that I have no idea what I'm doing with regards to networking. Could someone post a quick guide as to how to set up the wifi (from scratch) so that when it finds an unsecured network it will automatically use it for the internet.
Sorry if there's already a thread on this but I really can't find it. Cheers guys
-Mike
just what i need as well, i have just bought a wifi router so i can use the internet on my xda2s.
using the wireless manger -> wireless LAN manager i get:
STATUS: connected to network
SSID: NETGEAR
TX RATE: AUTO
MODE:INFRASTRUCTURE
CHANNEL 11
BSSID: 00-09-5B-D7-DC-2A
MAC: 00-09-2D-0B-C0-A6
but even when i pull the Ethnet cable (forgot how its spelt) out of the back of the router it still stays connected. so im thinking its more my PC than the xda. the thing is the router came with no software so i have no idea if its connected properly. when i pull this Ethnet cable out of the wifi router o get network cable unplugged. The network card is Broadcom 440x 10/100 Integrated Controller. Which I have never used.
if anyone has a any ideas it would stop me pulling my hair out.
Sorry to hijack this thread
mike freegan said:
However, the wifi baffles me! I have access to an unsecured wireless network with internet access, and my 2s will connect to it. When I go on the the internet on my XDA, even with wifi connected it still tries to connect GPRS to use the internet. If I keep clicking cancel, it will load the page (presumably through the wireless network's internet access).
-Mike
Click to expand...
Click to collapse
Mike, I dont think the wifi first and GPRS next works. It doesnt work properly on mine either. If I try a internet access via gprs and a local wifi is readily available, the system does not automatically switch to local wifi.....I think this could be a microsoft issue than a xda issue.
robboy said:
but even when i pull the Ethnet cable (forgot how its spelt) out of the back of the router it still stays connected. so im thinking its more my PC than the xda. the thing is the router came with no software so i have no idea if its connected properly. when i pull this Ethnet cable out of the wifi router o get network cable unplugged. The network card is Broadcom 440x 10/100 Integrated Controller. Which I have never used.
Click to expand...
Click to collapse
when u pull out the ethernet cable from the back of the router, can you still surf the net from you xda or PC?? that seems odd. So either you are not connecting to "your" own router, or someone else has a same router with unsecured setup and you were locked onto their service....if you follow what I mean. what happens if you kill the power to your router? you should definitely notice that the wifi service disappear in your xda and PC.
Dont expect a router to disappear by simply unplugging the ethernet cable, if the router is powered up, it will show up on your xda and the PC although obviously there will be no internet access.....
sorry if i wasn't clear. i meant i was still receiving a signal from the wifi router. i could never use the internet on the pda
update:
i can browse my pc files wirelessly using resco explorer, using the standard file explorer i can view the pc files using \\network/c and i have finally been able to connect to activesync.
however i still can not connect to the internet.
Any ideas, from looking on this forum it seems lots of peeps are having problems with this but nobody seems to have the answer
XDA Wi-Fi Solution....It Works!!!!
Hi,
I'm new to the forum and new to XDA2i (presumably XDA2s is same!) ....
I too had many frustrations connecting the wi-fi...but now I've cracked it, here's how.......
On first very first use (or following a hard re-set) device users are prompted to choose “What do you want WLAN to connect to?” The option bullets are ‘Internet’ or ‘Work’….’Work’ should be selected, this will connect them to the nearest WLAN (if this network is WEP encrypted it should be switched to ‘Open’ rather than ‘shared’ as is often the case).
Next prompt asks for any WEP Encryption ‘Pass Key’ to be input, when doing so omit any ‘-‘ between character pairs. Normal start-up should then be completed. Once device is up and running…..
From ‘Start’ pull-down on the ‘Today Screen’ select…. ‘settings’>’connections tab’>’connections icon’>’advanced tab’>’Select Networks’> pull-down ‘My Work Network’ > ‘OK’ out of selections to save and exit.
Go to ‘Wireless Manager’ in programs, select WLAN icon from main screen (which should turn green to show active), then select mini ‘WLAN’ icon from lower toolbar to see the status of the connection, quality of signal etc.
That did it for me......
Cheers
windupmerchant
We have a 3com wireless router at home. The laptop downstairs connects to it through a PCMCIA wireless adapter. My phone also connects to it fine, no probs at all.
However, we have a pc upstairs with no wireless on it at all. I have been told that I can use the phone to "simulate" a wireless connection to the router through its USB connection. I have tried this using the program Wireless Modem on the phone but to no avail. Windows XP keeps looking for a driver that a dont have and is not supplies on the CD that comes with the phone. Any ideas where I can get this driver from, or am I doing this just completely wrong...... :roll:
Thanks
There seems to be a growing amount of threads regarding the whole WiFi scenario.
I have experienced problems too. I have managed to configure the wifi and it picks up my belkin wireless router but it cant surf.
I am also using XP!
Your problem is slightly different to mine but I will have a go at your problem too.
GOOD LUCK!
Ok. JUst to update, i have found the drivers that install the the phone as a HTC USB Modem but im still having no luck. Im trying to simulate my phone as a wireless card to connect to my router downstairs.
Is this possible???
samething
Ive just got myself in the same situation. I have the XDA2i connected to my WIFI router fine, I can go on the WWW. Im now need to get my laptop into the loft where Im doing some work on an iriver H10 20gb (trying to construct a connection box as they arn't available until Sept!!!) I need the net access to look up pinouts on chips. I don't have a WIFI card for the laptop yet (should be here soon as on back order :evil: )
SO I want to use the PDA as a wifi card for my laptop through the usb port. How do i get the laptop to see the PDA as a network card and configured for this operation??
Cheers
I had been successfully tethering via Bluetooth with WM6's Internet Sharing function, and was doing so in XP. Well we just took the Vista plunge and I'm having an issue. The Network Connections is showing my BT connection as "Local Only" meaning I can browse other pc's on the network, but I can't get to the internet. My WiFi connection to my router connects to the internet with no problem (The Wireless Connection shows "Local & Internet Access."
So I can not get out to the internet using my Tytn as my connection. I used the "Diagnose Problem" function in Vista, and it tells me that it cannot ping IP address 192.168.0.1. This is the IP address of my router. I don't want it to try to hit that IP address, but I can't find a way to tell it NOT to. All the settings in TCP/IP protocol are set to obtain an IP address automatically. But it seems that even while using BT as the connection, it still wants to get to my router first, even though I'm not using my WiFi at all. I even tried disabling the WiFi connection. Still the same issue.
Does anyone know what I can do to get the pc to stop trying to get my router first?
Thanks!
Tell me about it! It took me an age to find some drivers that worked with my bluetooth, I ended up using the Toshiba stack. After a lot of fiddling I got it working but when it runs it is very hit and miss and I have yet to transfer anything between devices let alone surf the net! Have you tried the bluetooth set up wizard?
stpete111 said:
I had been successfully tethering via Bluetooth with WM6's Internet Sharing function, and was doing so in XP. Well we just took the Vista plunge and I'm having an issue. The Network Connections is showing my BT connection as "Local Only" meaning I can browse other pc's on the network, but I can't get to the internet. My WiFi connection to my router connects to the internet with no problem (The Wireless Connection shows "Local & Internet Access."
So I can not get out to the internet using my Tytn as my connection. I used the "Diagnose Problem" function in Vista, and it tells me that it cannot ping IP address 192.168.0.1. This is the IP address of my router. I don't want it to try to hit that IP address, but I can't find a way to tell it NOT to. All the settings in TCP/IP protocol are set to obtain an IP address automatically. But it seems that even while using BT as the connection, it still wants to get to my router first, even though I'm not using my WiFi at all. I even tried disabling the WiFi connection. Still the same issue.
Does anyone know what I can do to get the pc to stop trying to get my router first?
Thanks!
Click to expand...
Click to collapse
stpete111 said:
I had been successfully tethering via Bluetooth with WM6's Internet Sharing function, and was doing so in XP. Well we just took the Vista plunge and I'm having an issue. The Network Connections is showing my BT connection as "Local Only" meaning I can browse other pc's on the network, but I can't get to the internet. My WiFi connection to my router connects to the internet with no problem (The Wireless Connection shows "Local & Internet Access."
So I can not get out to the internet using my Tytn as my connection. I used the "Diagnose Problem" function in Vista, and it tells me that it cannot ping IP address 192.168.0.1. This is the IP address of my router. I don't want it to try to hit that IP address, but I can't find a way to tell it NOT to. All the settings in TCP/IP protocol are set to obtain an IP address automatically. But it seems that even while using BT as the connection, it still wants to get to my router first, even though I'm not using my WiFi at all. I even tried disabling the WiFi connection. Still the same issue.
Does anyone know what I can do to get the pc to stop trying to get my router first?
Thanks!
Click to expand...
Click to collapse
The internet sharing function on the TyTn used 192.168.0.1
You are saying that your router is also using the same address range.
That is a no-no. Change the router address to 192.168.1.1, and I think you will see better results.
@boz - Actually I have no issues connecting to Vista via Bluetooth, and all profiles work great (I'm using the latest Broadcomm stack). My issue is in my Network Connections, not BT itself.
@Wildbill - the Tytn is not using 192.168.0.1. The PC is trying to ping that IP address because it is the address of my wireless router, and the first time I ever accessed the net with that pc, I did so via WiFi through my wireless router at home. Now, what I am trying to do though is get on the internet in my car, while nowhere near my wireless router. But my pc still seems to want to get to my router as though I'm trying to connect to the net via Wifi, when I'm actually just trying to get to it through my phone. The PC connects to the phone with no problem, and the phone is connected to the internet, But, my problem is that I can't figure out how to tell my pc to NOT look for my wireless router's IP address first.
BT DUN was so much easier with Cingular. I wish one of the cooks could figure out how to get the DUN profile back into WM6's BT stack.
I am really confused here.
When you use Internet Sharing on the TyTn, You are using the Tytn to allow other devices to access the Internet thru the TyTn.
When you do that, the TyTn hands out the address of 192.168.0.100 and it is the gateway, and the Gateway address is 192.168.0.1.
If you have your home router using the same address range, you have the PC that the Tytn is sharing it's internet connection with seeing to addresses within the same range, and two gateways with the same address - The PC LAN card is seing the router at 192.168.0.1 and the Buetooth PAN is seing the phone gateway at the same 0.1 That is what I was trying to say. It won't work like that.
Oh ok I see what you're saying. I was assuming that when it gave me the error, that it was trying to ping my router since I knew that to be my router's address. I did not realize that the Tytn used such a similar gateway.
To correct what I said in my first post: I said that it was trying to ping "IP address"... the exact error message reads "Connot Communicate with DNS Server 192.168.0.1"
It shows a nifty little diagram of the PC connected to the Cingular Bluetooth network connection, then another line connecting to a picture of earth, which they call "internet," but there is a red "X" over that line showing that it can't connect to internet. When you click on Diagnose problem, the above error message is what comes up.
So now, I need to make sure I understand what you are saying Wildbill. I see what you mean from your post... being that I don't connect to my router anymore, ever, at all (since the pc never comes out of the car anymore, and I'm way out of range of my wireless router even in the driveway) what do I need to change? Everything in TCP/IP protocol settings are set to obtain addresses automatically.
Another interesting thing to note is that I did not have this problem when I had XP in my car, and I connected to my wireless router with that pc too. But Internet sharing worked fine with it.
If the only things connected are the TyTn and a PC, then the PC will obtain an IP from the TyTn, and it will be 192.168.1.100. It will tell the pc that the gateway is 192.168.0.1, which is the TyTn. Since the TyTn has Bluetooth 2.0, I would speculate that you could connect additional BT devices to the same BT PAN, and the TytN would likely hand out additional addreses like 0.101, 0.102, etc. I have not tried that nor have I read about it.
See that's what I gathered too. So I don't know why it can't get out to the internet, unless it's that Vista just won't let it for some reason. This bugs me because Internet Sharing worked fine in XP, and BT DUN works fine with Vista with my other phone. Unfortunately I'm getting rid of that phone. If my Tytn had a DUN profile in the BT stack I'd be fine. Weak.
i tehering in wm6 vista using bluetooth ban