I have a Tomtom Bluetooth GPS I need to get GPS information from the XDA to connect to a APRS system. I need to get the following information from the serial port GPS Data Out, GPS Data In & GPS ground.
Has any one got any idea how i can get this information out of the Serial port. Any help appreciated...
Thanks Stuart
hi
It'll be hard.
It's impossible to achieve without special software (which I don't know about).
The software would have to receive GPS data from bluetooth com port (eg. com8) and channel it to software com port (for TomTom) and to hardware com port (bottom xda connector).
I assume You won't be able to write such program.
My suggestion is to get a second GPS recevier (cheapest serial GPS mouse) to serve your APRS (whatever it is )
Good luck.
can some one here please help me this is driving me mad for days now i have been looking thro the forums at some of the posts how to set up tomtom 5 and how to setup the gps bluetooth receiver i have followed all instructions how to but iam not getting any where tomtom is installed ok the gps control panel is installed but i cant seem to get any blue tooth com ports to show up in tomtom apart from
qct data interface
ril on com6
com7
serial cable on com1
Ir on com3
if i rember when i had it installed on my xda2i when i went to tomtom and
bluetooth other then com ports i could pick from tow bluetooth coms 5 & 6
this really is getting to me now i do believe it possible to do it there guys selling the info on ebay with pictures of it running on the xda exec but i just cant seem to do it
please i would be so greatfull for any help i only got the phone last week i like it
sorry i think i had posted this in the wrong place iam not used to forums
thanks any way i have sorted it out now my xda exec is working really well with my tomtom and gps bt-77 receiver all is good
hi there
new to this forum which looks very interesting. Hence asking answer for a problem.
i have bought a Holox BT-321 gps receiver which is blue tooth enabled and i am trying my xda exec to recognise it. aftre turning both devices on xda can see the receiver but puts a yellow question mark before its name.
when turn the gps software on ((Medion Navigator) it does not recognise presence of the gps receiver.
i have great hopes that out there some one does know the answer to this.
to me it appears a software conflict as xda can not install this receiver.
i have tried O2 but they politely refused and asked me to contact gps receiver makers who in turn say the receiver is working fine!!
i was about to pay for a software pathway for sale at ebay but it had been banned by the ebay.
so help please
mohammad asif
Assuming that you did set a port for it (not sure whether it's incoming or outgoing) on the Exec for the GPS unit, you'll probably have to set the port to see the GPS unit on the software also.
That's how I got my GPS unit to work with my software. Please note that the software and the GPS unit that I'm using are not the same as yours. So results might vary.
I too am having exactly the same issues with the Holox 321 and o2 Exec. If anyone has had success pairing a using these two devices and can post a step-by-step walkthrough on how to do it I'd be very grateful.
Thanks.
MDA Pro and BT321
I have got exactly the same problem. It seem that the bluetooth works but the GPS receiver is not recognised. I was thinking of it could be missing drivers or something along those lines
I'm seeing a trend...
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Thanks BBD, that may help. Trouble is though, I can't even get it to pair correctly. The Exec seems to go through the motions, but the blue light that's meant to flash whenpairing is successful just stays solid.
I also get the question mark appear next to the device in the list of BT devices. What OS is your friend using? WM5 or PPC2003?
hi m8,
he is using WM2003SE, he two has the question mark beside his device I think that just means it does not have a Windows Certificate nothing more, just cheked my TOMTOM device has the question mark too and that works fine
Matt
hi,
just double checked and this is how it worked, pair the GPS receiver up, then go into TomTom and use the NMEA devices with baud rate of 38400 then select bluetooth on com6 and bingo bango your off
cheers
Matt
I think my problem occurs before TT5 is even invloved. From what I've seen WM2005 is very different from PPC2003 as far as BT goes.
I search for a new device and the BT-321 is seen as normal. I select it then enter the sec. key; ok so far. then I'm ask what services I want to use (only "serial port" is available). I select this, then finish. At this point I expect the blue BT light to start flashing telling me I have a successful pairing, but it stays solid. I have tried creating a new outgoing port, but no change.
Until I can get a successful pairing my BT port doesn't appear in the list in TT5, so I can't select it.
I wish I could find someone who has successfully paired these two devices...
Bump.
I can pair my mini s to the bluetooth reciever, but not tt5
i have paired my bluetooth reciever with my xda mini s but when i go to select it in tt5 none of the comports correspond with any i can pair the reciever with. I have installed bttools but this hasnt helped either. someone suggested i needed to build a com port but i dont know where to start, and they also said its because its an xda that theres comport problems, i donubt im the first one with this issue. i pray someone can help me out, would be much appriciated.
email [email protected]
Same problem on my Wizard with the Gpslim 236. However, my fiend brought over his rikaline last night and it worked very quickly. Go figure. I think I'll be exchanging today.
I got the BT321 working with the Universal no problem.
It paired okay, gave me the COM Port option which I took, showed the icon with ? on it.
Going to the COM Ports tab, I created an outgoing port (COM0).
In TT5.21 (I think you need the latest version of TT5) I selected COM0 and after a while it found it no problem..
F.
paring xda exec + gps holux 236
i did pare the 2 after updating tomtom to 5.21 free from tomtom web site then u get com 8 were u can set the outgoing port from the xda ,voila
I have XDA EXEC and have successfully installed the Holux BT-321 Bluetooth GPS. It runs perfectly with a number of GPS applications - so I know the port/Bluetooth configuration is ok. I had to choose an unused com port (0 or 4 work fine). (Ports 1,2,3,6,7,and 9 seem to be already used by the XDA EXEC - so could not be seleted).
BUT (going back to the first post) Medion Navigator (4.2) does NOT recognise the new GPS port. Instead it has options to select ports com1,2,3,6,7,9 but not the "new" port where the GPS is actually configured!
Does anyone have any ideas about this?
After several hours trawling forums and trying lots of things here's what worked for me on an XDA Exec running WM5. In fact I was shocked when it worked! In return for this can someone please think up the next thing after Toothache! The WM5 bluetooth connection thing could also do with a re-write - as could the WM5/XDA Exec instructions/FAQs/help, etc... on BT:
If your aim is to get TomTom working AND you're using a non-TomTom BT GPS, try this (the TomTom GPS seems to install itself without much problem):
1. Pair the GPS with your device BEFORE installing TomTom, because the GPS port needs to be already setup on your device for TomTom to recognise when installed.
2. Then install TomTom
3. Launch the BT connection thing in WM5. Make sure the BT is discoverable (first tab). Select 'Security' tab and ensure 'Authentication (Passkey) required is checked.
4. Go to 'Devices' tab and select 'new partnership...' The pairing thing should find your GPS and will then ask for the passkey - select next WITHOUT entering anything even if there's a passkey. If you enter the passkey now you will not get step 5 which is a crucial milestone.
5. The device should now ask if you want to add the GPS to your list, select yes
6. The name of the GPS is shown. Ensure 'serial' port is checked and hit next
7. You will be asked for the passkey again - enter it this time
8. At this point the GPS may look like it's not paired. The lights may flash as if unpaired. You'll also get a question mark icon next to the GPS in your list. Not to worry.
9. Select 'com ports' tab and select 'new outgoing port'. You should see your GPS listed. Select it and hit next. From the list of ports select COM8. Make sure the 'Secure connection' is UNCHECKED - otherwise you'll be pairing everytime you start TomTom! Select Finish. You should see your GPS (COM8) listed in 'COM ports' tab.
10. Turn off 'device is discoverable' (first tab).
11. Now install TomTom. Having installed the GPS as above, TomTom will now know about COM8 i.e. where your GPS is to be found. If you hadn't done that first there would be no COM8 and no GPS connected to it as far as TomTom is concerned.
12. Turn on the GPS
13. Launch TomTom and go to 'preferences/ GPS Settings'. Select 'configure'. Select 'Other bluetooth GPS'
14. You should get a list of ports and with any luck you should see 'COM8' - select it and hit 'done'.
15. I think at this point the GPS page in TomTom came alive, or maybe I had to restart TomTom - can't remember. And it works thus far!
Toothache - what a palaver!
BT/GPS Problems
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
bigbird49 said:
Hi,
I have a program that can sort out the com port problems between the bluetooth and gps software.
I have included the program as an attachment, just unzip it into your PC, make sure you reboot your PDA, sync your PDA to the PC and run setup.
Problems solved.
Cheers,
John
Click to expand...
Click to collapse
Hi,
I`m a new member.After installing your litle tool i can`t start this application and also can`t find it under programs or anywhere else?
I`m using a T-Mobile MDA Compact II with WM5 latest ROM, a Holux BT321 and TomTom6. `have expierences with BT and XDA`s using TT5 for a long time.
After upgrading to new devices and new sw i have the following problems:
I can connect the BT321 as a BT Mouse and get a good signal.Using TomTom6 the navigation works with a delay of round about 100 meter. I`m looking for a resolution to connect the BT321 via the NMEA Interface.
regards
AK
____________________________
MDAc II
WM5
BT321
TT6
Britishbulldog said:
hi all,
My m8 has one of them on an XDA2i and the only way we could get it working with TT5 was to set it up as other NMEA GPS on com 6, that did the trick
hope that helps
Click to expand...
Click to collapse
I have tried your advice and it works a treat, thanks to you and everybody else who contribute to this forum
Hi!
Is there a way to use the GPS receiver that is built into the Artemis as a GPS Device for Windows (XP or Vista).
Maybe over Bluetooth or USB / ActiveSync connection.
I tried to set up Bluetooth COM Ports so Incoming BT connections connect directly to the GPS COM port, but without success... no gps data was coming through.
Also I search for a small tool to test the receiver... just a compass or something.
regards,
Daniel
You cannot just "bridge" the GPS com port to your desktop OS via BT. The BT stack was never designed that way. All BT com ports you use must have a piece of software behind it to fill it with data, or otherwise they are just empty cans.
In your case, you need a GPS splitter to get gps signals from the GPS com port, and then repeat it to a BT com port so that the other end can receive such signal. That will provide a working bridge for your data.
Try software such as gpsgate that works as described above.
Hello, you can try GPS2Blue is a little free program that will let you use your Artemis as a GPS.
You can find it here: http://users.skynet.be/hofinger/GPS2Blue.html
Enjoy.
i got myself GPS2Blue and installed it.
My problem now is, that i cannot set up a BT COM port!
I have the (german) B&Bv3 ROM (WM6). In Bluetooth Settings in the "COM Ports"-Tab. It says "Tap on 'New outgoing port' ..." but theres no button or something. Just the describing text and an empty ListBox.
since I cannot set up my COM port, GPS2Blue won't swich on right?
So... is this a WM6 bug or a B&B Bug or my brain-bug
Setting up COM ports in my firmware WM5 OS worked just fine.
Thanks you guys for the info!
but what to do now?
GPSgate can do what you want (but it is not free)
gpsgate can set up bluetooth com ports? i dont think so
this is not a gps problem anymore!
i posted a new thread for my new problem:
http://forum.xda-developers.com/showthread.php?t=315687
GPSGate can do it!!
Use this is the registration key:AmzeaBjw
Then your Artemis can pass GPS information to your PC through Bluetooth
Fransons GPS Gate will enable the sharing of GPS position to a number of different types of device, I am not too sure about posting a registration key for purchased software as these are specific to an individual user??? - Mike
I have never tried the bluetooth connection on my exec until now.
I received my new Bluenext BN-906GR today and I can't make it associate with the EXEC.
I have entered the data on the bluetooth connection such as the passcode and the port, but the info which came with the GPS device says to select SPP slave on the connection which is not offered by the XDA connection tabs.
I have deleted the connection and tried over and over again. The only time I get a solid bluetooth LED on the device is when I enter the pass code, after that it goes back to blinking led which means it is not connected.
Any help would be greatly appreciated.
The XDA exec is running WM5 oS5.1.195
Thanks
Tony
Ah - I solved it. The instructions that came with the kit gave me the wrong instructions regarding ports to set in the software. In fact when I just try to make a connection in bluetooth, it won't connect, however, with the correct port set in tomtom, the darned thing works just fine when I run the tomtom software. It is definitely not set up as the instructions say, but it works just fine.
For information in case anybody chances on this thread later with the same problem, I set the outgoing port to com 8 in the bluetooth settings page and set the same port in tomtom as the port to talk to. I have not set bluetooth on in the bluetooth settings page, tomtom sets it up for me.