Tech-Ed 2005 and WM2005 - MDA III, XDA III, PDA2k, 9090 General

I know I have been lurking for quite a while but hold on to your hat.
While reviewing the new PPC devices running WM2005 in Tech-Ed I discovered a BlueAngle device with a WM2005 sign above it. Thinking someone made a mistake I took a closer look... The images are crappy but hey, it's a BlueAngle.
I will make an attempt to get a ROM backup of it but not sure if I can... This at least proves that there is indeed a ROM out there for this device..

Do you know who was presenting on the stand (Microsoft, HTC or a Telecoms Carrier)?
Did you try the device out and was it FULLY functional (Telephone, camera, wifi, bluetooth etc) or was it a basic implementation of WM2005 without drivers for BlueAngel hardware?
I'm sure there will be a lot more interest in this thread if you are able to get hold of the unit for "testing"!
Happy hacking...

Yeah, lets get a hand on it, man! 'd be nice, if a version of magneto would leak out...

Nice! I was getting my hopes down, but now it looks like it's a matter of time until we get our hands in that baby

MrHappy, if you managed to get the Rom off that device you would make ALOT of people VERY happy. If you can do this, you will be the most popular person on Blue Angel forums everywhere .
But, I have the same questions as Bebbo.
1) Whose device is it? Microsoft? HTC? etc
2) Is it fully functional?
I would SO just go up to the device, stick in an SD Card, dump the Rom, and run away .

hey that would be great if you can handle that!

TheLastOne said:
I would SO just go up to the device, stick in an SD Card, dump the Rom, and run away .
Click to expand...
Click to collapse
Ha ha ha, I second that advice

Yeah, it looked like it had all the pieces.
How do i backup a rom? xbackup? Believe me, if I can get a backup of it i will....
pointers on anything that will just backup when I put the sd card in?

did you see htc alpine aka pda 2 aka xda2i with 2005?
if so could you try getting that rom aswell
goodluck

For all I know, this is the only way http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=151
Which will be quite hard for you to do

hell dude there is no way they are going to let me synch this thing up with anything. Isn't there a program I can autorun on my sd card that will do it? As you can imagine, they are hovering over this rack and the phones are clamped down tight.

you dont have to sync it, just close wcecomm in your taskmanager and follow the procedure 2 posts above, should work as usual

Just ROB IT AND RUNAWAY!! :>

But you still need a PC connected???
What we need is an app to put on the SD card -> put card in PDA -> copy application to PDA -> run it -> data written to SD card. (itsme - where are you when we need you????)

Okay i´ve got an easier procedure:
1: download this program: http://www.mcinternet.net/iwan/mtty.zip and place it onto desktop
2: CTRL+ALT+DEL and close wcescomm.exe in your taskmanager (only if you got active sync)
3: at the pocket pc: hold reset (with stylus) + speech record button + Off/On button - hold it for some seconds now it will be shown the Bootloader
4: start the tool mtty.exe just keep \\.\WCEUSBSH001 and right of that the USB , then just click OK
5: open a new blank file in the program and when you see typed: USB>
you have to click d2s
6: wait until the program shows: ************************************************** *******
Store image to SD/MMC card successful.
USB>
7: than just reset the pocket pc
now youve got an backup on you sd card (by the way it should be bigger than 64MB´s)
-----------
to get the backup file onto your desktop computer (you need an Cardreader on you pc):
1: load this program: http://forum.xda-developers.com/viewtopic.php?p=60435 (NTRW.exe) copy it on C:\NTRW\
2: Press START Button -> Run... -> type in "cmd" without the ""
3: now it will be shown: C:\Documents and settings\your user name>
4: type: cd\ntrw
5: after that type: ntrw read windowsmobile.nb1 C:
6: then you have to wait a few minutes (i waited about 10)
7: you find the windowsmobile.nb1 in your c:\ntrw folder
8: upload it
greets and hopefully it works

As previous comment - This requires a PC to complete and MrHappy is at a show with a PDA on a stand - No connected PC.....
We need a simple util on the PDA itself....

dumped, i don´t know any tool using only the pda... like from some other posts grab it and run

There aren't any tools to do it that way... You need to be in bootloader for it to work.. And in bootloader you can't run anything on the pda...
So i think that without the PC connection it will be impossible to do it.

Quoting itsme from the Wiki http://wiki.xda-developers.com/index.php?pagename=XDAtools he has a tool which ...
You can even read and write images to and from bootloader SD-cards through ActiveSync while your device still has its OS running.
Click to expand...
Click to collapse
I guess this works the same way as the developer tools for CE (They link into the PDA directly via ActiveSync)
I have PM'd him and asked if it is possible to do this direct on the PDA itself ... here's hoping.

The problem here is that he has NO PC. I believe we also have a time limit, as Tech-Ed doesn't stay around for ever.
Can you bribe the person at the booth to turn around while you walk out with it? I'm sure we could get enough people here willing to contribute to the bribe fund .
Or alternatively, can you bring a laptop? (ROFL)
But seriously, unless we can find a way to dump the Rom to an SD Card using a Pocket PC program WHILE the OS is running, we are out of luck here.
Well, even though this will likely end up in failure, at least we know that WM2005 for Blue Angel is within our grasp.

Related

a little help on upgrading...

dear ladies and gents,
i am new to this forum; i have been using my xda2 for 2 years now and i am more or less up to speed on the how to's. but i have a question on upgrading to wm2005. i deeply apologize if this topic has been discussed before and now here i am again bringing it up...but hear me out first.
i have downloaded ALL the files needed to upgrade to wm2005; the roms (version c) from buzz.net, the ramdisk, doctools, even the skins. so far i know only the following steps (i got this from xda2jojo's downloads). everything.
--------------------
5. Start your device in bootloader mode by pressing and holding down:
DPad + PowerButton + ResetButton
After a second release ResetButton, then release the rest of them.
Your screen will show word "Serial" at the top.
You are in bootloader mode now.
6. Place your device in the cradle, ensuring that the cradle
is plugged directly into a USB port on your PC and not to a hub
and that the power supply is connected to the cradle.
It is also a good idea to disable any screensavers on your desktop PC.
Once your device is cradled, the text on the screen will change to "USB".
7. Run HimaUpgradeUt.exe
8. Sit back and wait for the Congratulations screen to be displayed
on your PC. Your device will still be displaying 'Upgrading radio stack, please wait',
but as long as the PC says it is done, then its all OK.
9. Detach your device from the cradle.
10. Now you have to hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
-----------------------
i have successfully done this already but the storage is low. i have done reading and browsing on expanding the storage to 30-plus mb using ramdisk and the doctools. i would like to ask for assistance on how to use these. i read in this forum that you have to use doctools first? it is a little confussing.
please advise how to use these 2 tools together with the steps mentioned above.
again i apologize in advance because i know that this topic has been discussed so much.
pietro
you need to (got this from the forum):
1. Downgrade to WM2003SE (2.06 ROM) via PC method
BUT if you're already running WM2003SE then you don't need to do step one. But at the very least I think your ROM should be 2003SE.
2. Install Extended_ROM Unlocker
3. Unlock the Extended_ROM (but don't click unhide)
4. Copy the Hima_DOC_Tool.exe to the Temp folder on the device
5. Run the Hima_DOC_Tool.exe
6. Perform a soft reset only (not hard reset)
7. Checked the new size (30.07M
8. Upgraded to WM2005 (1.60b.96) via PC method
it worked for me. you may want to also refer to this link:
http://forum.xda-developers.com/viewtopic.php?t=28801
and
http://forum.xda-developers.com/viewforum.php?f=42
these will more or less answer other concerns you might have.
in my case i didn't use ramdisk...but it worked well for me and i'm still using wm2005.
cheers
rob
IT WORKED!
Thank you very, very much for your post! After some experimentation I was finally able to solve the storage problem based on the guide you gave me!
Pietro

Confused "noob" :)

Hi All
I really have tried reading up on HSPL and SSPL - and I have been very close to trying to flashing my brand new Diamond Touch, but everytime I cancel the last operation, flashing the phone.
I got it yesterday, and it is a businessphone - but still I want to play a little around with it, trying some of the stuff that is out there.
Beeing a businessphone I really need to know what I am dooing - and therefore I have read the wiki about HSPL and SSPL, and I think I have an idea of what is what - but then reading some of the threads about new HSPL's I still get confused... It might be the heat here in Denmark as I am no noob at flashing stuff, like PSP's, Ipods...
So, after all this - to my noobish questions...
1. When flashing/installing a HSPL (not SSPL at the beginning) I do not hardreset anything, it is just a new bootloader? My phone software (SSPL) is in danish, så I dont want to mess that up!
2. I see instructions like the ones below, but am I right to think, that I have to copy the file DiamondCustomRUU directly to the phone - and not try to run it from my pc? And how do I choose which HSPL .nbh-file that I want to use - I think I have downloade 5 different at this time.
So I think that there might be one or more steps missing?
1) download hardSPL
2) create a new folder on desktop
3) unzip to new folder
4) plug in your device
5) wait until Windows Mobile Device Centre on your PC says "connected"
6) run diamondsspl.bat from the new folder you just created
7) spacebar all the way
8) your PDA will show up a window
9) click close/continue on PDA
3. I have tried running RomUpdateUtility from Unsigned-Hard-SPL-Diamond-OliNex. The software do connect to my phone, and tell me what software I am currently using, but when I click "next" to make the update, nothing happens for a while - and at the end it times out...
Ok, thats it - I just want to be 100% sure what I am doing!
Zulfo said:
Hi All
I really have tried reading up on HSPL and SSPL - and I have been very close to trying to flashing my brand new Diamond Touch, but everytime I cancel the last operation, flashing the phone.
I got it yesterday, and it is a businessphone - but still I want to play a little around with it, trying some of the stuff that is out there.
Beeing a businessphone I really need to know what I am dooing - and therefore I have read the wiki about HSPL and SSPL, and I think I have an idea of what is what - but then reading some of the threads about new HSPL's I still get confused... It might be the heat here in Denmark as I am no noob at flashing stuff, like PSP's, Ipods...
So, after all this - to my noobish questions...
1. When flashing/installing a HSPL (not SSPL at the beginning) I do not hardreset anything, it is just a new bootloader? My phone software (SSPL) is in danish, så I dont want to mess that up!
2. I see instructions like the ones below, but am I right to think, that I have to copy the file DiamondCustomRUU directly to the phone - and not try to run it from my pc? And how do I choose which HSPL .nbh-file that I want to use - I think I have downloade 5 different at this time.
So I think that there might be one or more steps missing?
1) download hardSPL
2) create a new folder on desktop
3) unzip to new folder
4) plug in your device
5) wait until Windows Mobile Device Centre on your PC says "connected"
6) run diamondsspl.bat from the new folder you just created
7) spacebar all the way
8) your PDA will show up a window
9) click close/continue on PDA
3. I have tried running RomUpdateUtility from Unsigned-Hard-SPL-Diamond-OliNex. The software do connect to my phone, and tell me what software I am currently using, but when I click "next" to make the update, nothing happens for a while - and at the end it times out...
Ok, thats it - I just want to be 100% sure what I am doing!
Click to expand...
Click to collapse
Why invent the wheel again when you could go here http://www.modmydiamond.info/
My jewel is also my business tool
Skimmed down walkthrough:
1.instal hardspl
2.chose rom of taste
3.flash with rom.
easy as abc
luck!!!
halloj said:
Why invent the wheel again when you could go here http://www.modmydiamond.info/
Click to expand...
Click to collapse
Ah, now I seem to be getting it!
Now I just have to decide on what HSPL to use - i want to use Cyphols DIAM.DAN.137.403-3 as it is a danish ROM, and it requires a developer HSPL as far as I can read....

Request from a Linux user - Flashing without MS Windows

HI everybody
Like other people on this forum, i'm a linux user
I'm working under Ubuntu Hardy Heron. It's impossible to run any RUU under this system using WINE ( Software than give the possibility to run windows apps under linux ) because it need an active sync connection witch also don't work.
So my request is the following: Can we have a ROM Update utility for our cheer Penguin ?
Big thanks to all developers that works so hard for our community
you and me both: i'm on Linux Mint 5, though
i don't think it's a problem of the people on here: i say it's microsoft's refusing to release drivers for activesync...
There have been attempts made, but i don't know if any of them are going to work with these newer devices... Try googling SynCE...
Hello penguin's friend
SynCE is hard to configure...
But the question is not about synchro, but for ROM updating.
Okay Microsoft is radin... But for upgrading we only need an USB connection for data transfer through the hard SPL.
Activesync is only necessary to retrieve informations from the PDA during an update procedure ( Rom version for example ).
But the flashing procedure doesn't require it ! the prove: when we lunch this procedure the active sync connection stops and the SPL appears on the PDA's screen.
Here is my idea to make it possible under Linux : Run manually SPL on the PDA, and start flashing directly (with USB connection only).
In fact, we only need a ROM Update Utility that pass-through device information retrieving step ( is it really important? ). May be it can works.
All of this could run with wine. But I still think that a native linux RUU is the best way to explore.
There still exist a linux RUU update program (I don't remeber where, but if you make a search into this forum you can find it).
The matter is another one...our diamond don't use the common way to establish a connection with the laptoop ( /ttyUSB0) and so, till now, it's impossible to update...we have to find a workaround for this issues...
I don't understand...
It's the SPL that give necessary connection (usb/serial). Is the problem from it ?
Exactly
Take a look: http://forum.xda-developers.com/showthread.php?t=410302
By searching, i found a solution by flashing from a SD card with a special SPL.
Its solution was developed for ARTHEMIS PDA here : http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Do you think this SPL could work on our diamond ( we don't have SD Card but internal storage ).
I'm afraid to try it. My be it can crash my device permanently ...
GriFolle said:
Exactly
Take a look: http://forum.xda-developers.com/showthread.php?t=410302
Click to expand...
Click to collapse
GREAT ! i go take a look
Sers,
for Linux, HTC Flasher from the link in previous post is what you need.
It's working well for much HTC devices but Diamond still got some connection issues. It doesn't get attached to any serial port in SPL Mode, so flashing via Linux seems impossible.
Even flashing throught Virtualbox doesn't work because it's impossible to attach the device to the VM.
Maybe you're gonna find a solution, let's hope.
regards
demacus
dominique2222 said:
By searching, i found a solution by flashing from a SD card with a special SPL.
Its solution was developed for ARTHEMIS PDA here : http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
Do you think this SPL could work on our diamond ( we don't have SD Card but internal storage ).
I'm afraid to try it. My be it can crash my device permanently ...
Click to expand...
Click to collapse
There you're wrong.
Take a look here: http://wiki.xda-developers.com/
In this thread a guy manage to flash Diamond via USB.
OK I have the solution !
It's very simple and don't need any computer!
BE CAREFUL BEFORE STARTING TO HAVE GOOD BATTERY !!!
Install Olinex hard SPL
Connect your PDA to linux in USB Disk mode
Simply copy your .nbh file into internal memory in root folder. rename it to DIAMIMG.NBH
Reset your device with pressing volume down and right key.
You will enter in Olinex SPL flash mode. Wait two seconds and it will ask you if you want to flash from DIAMIMG.nbh !!!
Thanks everybody for your help.
I think this solution is the more simple !
Congrats! Nice find!
This will make things much easyer for many ppl!
regards
demacus
it's much faster than trought async... always used this trick, the only thing to REALLY pay attention to have at least 40/50% of battery
All Right !
Is the file still there afterwards?
Nice find.
Possible to choose from more files?
dominique2222 said:
OK I have the solution !
It's very simple and don't need any computer!
BE CAREFUL BEFORE STARTING TO HAVE GOOD BATTERY !!!
Install Olinex hard SPL
Connect your PDA to linux in USB Disk mode
Simply copy your .nbh file into internal memory in root folder. rename it to DIAMIMG.NBH
Reset your device with pressing volume down and right key.
You will enter in Olinex SPL flash mode. Wait two seconds and it will ask you if you want to flash from DIAMIMG.nbh !!!
Thanks everybody for your help.
I think this solution is the more simple !
Click to expand...
Click to collapse
Thumbs up for you mate! super find, and saves us from messing with external USB hubs ....
Riel said:
Is the file still there afterwards?
Nice find.
Possible to choose from more files?
Click to expand...
Click to collapse
Well.....The file need that specific name.
You CAN transfer other files and name them, but you wont get a "menu" for choosing.
Just turn to your friend, and use his computer that runs Windows.
luzok said:
Just turn to your friend, and use his computer that runs Windows.
Click to expand...
Click to collapse
If prefer working under Linux Sorry Mr Bill !
Penguin 4 ever !!! YeaaaH !!!!

[TUT] Unbricking your Excalibur

Everything you ever needed to know about "unbricking" your Excalibur but were afraid to ask is in this guide. I've put together this guide for those of you who either intentionally or unintentionally "bricked" or think you've "bricked" your Excalibur.
It is not easy to brick an Excalibur if you actually read and follow all of the steps and guidelines before a flash. In fact, not many things can go wrong unless a USB cables disconnects during a flash, your PC crashes in the middle of a flash, or you flash a corrupt image file to your device. Statistically, most of the time people only think their Excalibur is "bricked" when actually it's not.
There are three methods you can use depending of the severity of the "bricking". The first method will unbrick 50% of all Excalibur's that have simply "locked up" and won't reboot properly. The second method will unbrick 95% of all Excalibur's that encountered flashing problems or flash failures. The third and final method, and the most involved, is a "last resort" for those who have tried method's one and two numerous times unsuccessfully.
** Please perform these steps and methods at your own risk. I am not responsible for any damage you cause your device using this guide.
If you're new to the Excalibur or SmartPhones in general, please take the time to read the WiKi and this post by Stylez for valuable info before you post or try any of these steps.
http://forum.xda-developers.com/showthread.php?t=397583
http://forum.xda-developers.com/showthread.php?t=537151
But, before I even get into unbricking, if your phone is in fact working right now, I highly recommend you flash HardSPL to avoid even having to follow these steps anytime in the future. The steps and info for HardSPL and JumpSPL can be found in this thread by jockyw2001:
http://forum.xda-developers.com/showthread.php?t=329605
HardSPL basically flashes your phone with an "unlocked" security partition so all security checks are bypassed when you try to flash a cooked ROM or a ROM designed for another variation of the Excalibur such as Dopod, HTC, TMO Dash, etc. Makes life much easier when trying different ROMS or cooking and testing your own! Thanks jockyw2001!!
Ok, so onto the fun stuff... Your phone won't boot... Either it's locked up and simply stopped booting or you flashed your phone and it won't boot. What do you do??
Method 1: Assuming you didn't get "bricked" from a flash problem, the first and easiest method for "unbricking" your Excalibur is (this will erase ALL data in your Excalibur):
(This method works for 50% of supposedly "bricked" Excaliburs)
Remove your SIM and SD card
Remove and reinsert your battery
While holding the two softkeys with your thumbs, press the power button
Continue holding the softkeys until a black screen appears saying "This operation will delete all your..."
Press "'send"' to restore to hard reset your phone
Let the phone cold boot and restore
That didn't work!! . This next method will reflash your phone to the factory ROM.
Method 2: Second way to the path of unbricking is:
(This method will unbrick 95% of all Excaliburs)
Get a hold of your Shipped ROM. You can find these ROMS either in Dopod's site, HTC's site (with a valid serial #), TMO's site (http://www.t-mobile.com/wmupgrade/ with a valid IMEI), or right here at XDA at this post (http://forum.xda-developers.com/showthread.php?t=381726)
Download one of these factory ROMS and unpack it. **Remember, if your phone is a TMO Dash, you MUST use a TMO Dash ROM. If your phone is HTC Branded, you MUST use an HTC ROM, etc., etc., etc...
Remove the SD card if one is inserted in the phone
Remove the battery from your phone for a few seconds. I found this step to be essential to reset the device. Put the battery back in.
While holding the camera button on the right side, press the power button. The phone will enter "bootloader" mode and you will see a tricolor bootscreen.
While in this mode, plug in your USB cable and you will hear the "ba-bing" USB sounds as the device connects
Unpack the ROM package you just downloaded and run RomUpdateUtility.exe. Follow the steps, check the appropriate boxes, and start the flash
Assuming all goes well, your phone will flash to the factory ROM and you can then troubleshoot what went wrong the first time that bricked your phone.
Oh no!! That still didn't work!? Or it worked but the flash failed with Error 270 or another error......... Never fear!! XDA-Developers is here! This next method is a bit more intense. It creates a "goldcard" which is used to SuperCID the Excalibur so that it doesn't care about what factory ROM you flash. Please have the factory (not a cooked) ROM ready to go.
** (This method is not intended for Newbie's and some enhanced knowledge of HTC devices and Windows is required to successfully work.)
** (Retry the second method several times with a few different factory ROMS before attemting the below)
Method 3: The third "goldcard" method is a bit more intensive and should be used as a "last resort" so follow closely:
(should unbrick ANY bricked Excalibur if performed correctly)
Get a cup of coffee or tea
You will need a working Donor HTC device with a microSD slot and a microSD card that is smaller than 1GB (will be formatted) to create "goldcard" image using QMAT tools as described below
You will need QMAT. Get it from http://revskills.de/index.html.
Go to the Download link and download the latest version and unpack QMAT
Have some coffee
Use a SD card reader (either USB for microSD adapter) in your PC to access the SD card through Windows. Format the SD card with FAT32.
* Insert the SD card into the donor HTC device and boot up the device. Connect the USB cable and establish an Activesync connection.
Open QMAT and go to the "Hardware Forensics" menu and select "Generate HTC Goldcard"
In "Select device key:" select the Excalibur
You will need the serial number fro the inserted SD card so click the "Get SD Card Serial from WINCE Device" button
Once the Serial number appears in the box, click the "Save Goldcard Image to WINCE SD" button below
If no errors pop up and all goes well, skip the next step
If you get an error or a popup saying "Goldcard for newer devices isn't implemented in newer devices", you must buy and register the software. Believe me, it's worth the small amount of $ you will spend to bring your expensive device back to life!
Now remove the SD card with the newly written Goldcard image from the Donor HTC device
Insert the SD card back into your PC using the microSD card reader adapter. Browse to the drive letter assigned to it. You will see no files on the SD card, this is normal.
(If, for some reason your PC sees the SD card as unformatted, something went wrong. Remove it and reinsert it into the Donor HTC device. The device should see the card as unformatted and ask you to format it, say yes. Now go back to the "* Insert the SD card into the donor HTC device" step above and repeat the steps)
Unpack your Dopod or other factory ROM and copy RUU_Signed.nbh to the SD card. Once it had finished copying, rename the file to EXCAIMG.nbh. Remove the SD card from the PC.
Make sure the Excalibur is off and insert the SD card
Enter bootloader mode as mentioned earlier (hold the camera button while pressing the power button). No need to connect the USB cable.
You will see a gray screen that says "loading". It will then find the EXCAIMG.nbh file and ask if you would like to start the update process. Follow the instructions and let the phone flash.
It will take 10-15 mins but your phone should boot fine and be back in action!
QMAT is a VERY powerful tool written by viperbjk that allows for full low level manipulation of HTC and WINCE tasks. Read all about it here http://revskills.de/index.html.
Many thanks to jockyw2001 for his amazing HTC device knowledge! Also thanks to all who contributed to this post.
Hope this tutorial helps!
Updates and more info will be here.
What if the phone will not enter bootloader mode?
ookba said:
Updates and more info will be here.
Click to expand...
Click to collapse
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
all steamed out said:
Hi OOkba,
This happened to a friend in the office's Dash. It simply froze up while operating. I actually got on the phone with HTC support. We couldn't get it to do anything. It does power up but then freezes.
The HTC guy was of the opinion that it is hardware related.
You ever solved that one?
BTW - I am running the 7.18 6.5 - love it - thank you so much
Click to expand...
Click to collapse
Thanks, glad you like it. Try this guide for your friend. Sounds like an easy fix unless it is indeed hardware related.
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
mydreamisrich said:
thank. I formated SD card and insert SD card in to my phone.But Do I need turn on my phone when connect with computer? because when I run QMAT software is error. " could not open connection? Device connected?". Help me. I need help from you
Click to expand...
Click to collapse
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
alfatech said:
HI OOKBA. I can't find my shipped rom. I have a HTC Excalibur from Digitel, Venezuela. The serial number is SZ702FJ05879. I try all roms and not working. Please, help me. (sorry my bad english)
Click to expand...
Click to collapse
English is good!! Who is your Carrier? Maybe your carrier has a ROM UPdate on their website? You should be able to use the TMO or Brightpoint ROM. You tried all the factory ROMS and they fail to flash?
ookba said:
Yes, you have to have a spare working phone to create a "goldcard". The phone must be powered on and sync'd via USB so QMAT can access the storage card.
Click to expand...
Click to collapse
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
aletkd said:
Sup ookba!
I really want to flash my TMobile Dash using your rom, looks pretty cool but I'm deadly afraid of bricking my phone so first, I took a look on my System Info and it says
ROM Version: 1.33.422.1 (tho its a TMobile Dash, I think the seller flashed it with this international rom).
Model Name: HTC S621
So I got 3 questions
1) Can i flash 3VO rom on this phone?
2) If the flashing fails, can i just use another 1.33.422.1 ROM and reflash it?
3) Will the flashing process (both ways) will bring the SIM Lock back?
Greetings from Brazil and sorry about my glass-cracking, horrible and ultra-bad english.
Click to expand...
Click to collapse
Yes, your phone is fine. Make sure you follow all of the flashing instructions. Make sure you remove your SD card, connect your phone, run SDA Application Unlock, and run auto.bat from the update package.
mydreamisrich said:
I tried turn on my phone. And connect computer by USB but the same error. QMAT can't access the storage card. What does I do?
Click to expand...
Click to collapse
I dont know what you're doing wrong. Sounds like you're not establishing an Activesync connection properly.
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
alfatech said:
Ok, Ookba. My carrier is DIGITEL and don't have support in the website. The phone comes originally with WM5 in spanish. I try all the factory roms and not working. Please, tell me if there is any solution or I forget the phone.
Thank you any help.
Click to expand...
Click to collapse
Try the "Goldcard"' method. This should SuperCID your phone and allow you to flash ANY shipped factory ROM. Please follow the tutorial closely. You will need a spare phone with a microSD slot.
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
alfatech said:
Ok, Ookba. But the spare phone must be a same model than mine? (HTC S620)
Click to expand...
Click to collapse
No, just has to Windows Mobile based and have a SDHC slot.
OK. I try with 3rd method and when run Qmat and select "Get SD Card serial from WINCE Device" appears the message "You need to set rigth registry permissions. See QMAT manual for more info." and not recognizes the sd card.
What is the problem?
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
alfatech said:
Thanks, Ookba. You're great, man. Finally someone offers solutions to my problem. Thank you very much. My Phone came back to life again. I make a donation soon.
Click to expand...
Click to collapse
GREAT!!!!! Congratulations!
I tried but when I click Get SD Card Serial from WINCE Device in the box none found and click Save Goldcard Image to WINCE SD is card ID isn't 16 bit (32 charter) long. I isn't succesful. help me???????

[GUIDE]How to Flash Your Vogue (CDMA Only!!!!)

Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....

Categories

Resources