Confused "noob" :) - Touch Diamond, MDA Compact IV ROM Development

Hi All
I really have tried reading up on HSPL and SSPL - and I have been very close to trying to flashing my brand new Diamond Touch, but everytime I cancel the last operation, flashing the phone.
I got it yesterday, and it is a businessphone - but still I want to play a little around with it, trying some of the stuff that is out there.
Beeing a businessphone I really need to know what I am dooing - and therefore I have read the wiki about HSPL and SSPL, and I think I have an idea of what is what - but then reading some of the threads about new HSPL's I still get confused... It might be the heat here in Denmark as I am no noob at flashing stuff, like PSP's, Ipods...
So, after all this - to my noobish questions...
1. When flashing/installing a HSPL (not SSPL at the beginning) I do not hardreset anything, it is just a new bootloader? My phone software (SSPL) is in danish, så I dont want to mess that up!
2. I see instructions like the ones below, but am I right to think, that I have to copy the file DiamondCustomRUU directly to the phone - and not try to run it from my pc? And how do I choose which HSPL .nbh-file that I want to use - I think I have downloade 5 different at this time.
So I think that there might be one or more steps missing?
1) download hardSPL
2) create a new folder on desktop
3) unzip to new folder
4) plug in your device
5) wait until Windows Mobile Device Centre on your PC says "connected"
6) run diamondsspl.bat from the new folder you just created
7) spacebar all the way
8) your PDA will show up a window
9) click close/continue on PDA
3. I have tried running RomUpdateUtility from Unsigned-Hard-SPL-Diamond-OliNex. The software do connect to my phone, and tell me what software I am currently using, but when I click "next" to make the update, nothing happens for a while - and at the end it times out...
Ok, thats it - I just want to be 100% sure what I am doing!

Zulfo said:
Hi All
I really have tried reading up on HSPL and SSPL - and I have been very close to trying to flashing my brand new Diamond Touch, but everytime I cancel the last operation, flashing the phone.
I got it yesterday, and it is a businessphone - but still I want to play a little around with it, trying some of the stuff that is out there.
Beeing a businessphone I really need to know what I am dooing - and therefore I have read the wiki about HSPL and SSPL, and I think I have an idea of what is what - but then reading some of the threads about new HSPL's I still get confused... It might be the heat here in Denmark as I am no noob at flashing stuff, like PSP's, Ipods...
So, after all this - to my noobish questions...
1. When flashing/installing a HSPL (not SSPL at the beginning) I do not hardreset anything, it is just a new bootloader? My phone software (SSPL) is in danish, så I dont want to mess that up!
2. I see instructions like the ones below, but am I right to think, that I have to copy the file DiamondCustomRUU directly to the phone - and not try to run it from my pc? And how do I choose which HSPL .nbh-file that I want to use - I think I have downloade 5 different at this time.
So I think that there might be one or more steps missing?
1) download hardSPL
2) create a new folder on desktop
3) unzip to new folder
4) plug in your device
5) wait until Windows Mobile Device Centre on your PC says "connected"
6) run diamondsspl.bat from the new folder you just created
7) spacebar all the way
8) your PDA will show up a window
9) click close/continue on PDA
3. I have tried running RomUpdateUtility from Unsigned-Hard-SPL-Diamond-OliNex. The software do connect to my phone, and tell me what software I am currently using, but when I click "next" to make the update, nothing happens for a while - and at the end it times out...
Ok, thats it - I just want to be 100% sure what I am doing!
Click to expand...
Click to collapse
Why invent the wheel again when you could go here http://www.modmydiamond.info/

My jewel is also my business tool
Skimmed down walkthrough:
1.instal hardspl
2.chose rom of taste
3.flash with rom.
easy as abc
luck!!!

halloj said:
Why invent the wheel again when you could go here http://www.modmydiamond.info/
Click to expand...
Click to collapse
Ah, now I seem to be getting it!
Now I just have to decide on what HSPL to use - i want to use Cyphols DIAM.DAN.137.403-3 as it is a danish ROM, and it requires a developer HSPL as far as I can read....

Related

Complete idiots guide needed, please!

It might be very simple to all you educated guys, but I am sure there are a few more like me that are a bit baffled by some of the threads on here.
What would be REALLY nice would be a 'simple' step-by-step guide to installing wm6 on our devices, and what we need to download to achieve it, eg "you need this for MDACIII, and this for O2 Orbit"
Obviously anyone trying it runs the risk of buggering up their phone, but that's their own fault.
Any volunteers?
stunno said:
It might be very simple to all you educated guys, but I am sure there are a few more like me that are a bit baffled by some of the threads on here.
What would be REALLY nice would be a 'simple' step-by-step guide to installing wm6 on our devices, and what we need to download to achieve it, eg "you need this for MDACIII, and this for O2 Orbit"
Obviously anyone trying it runs the risk of buggering up their phone, but that's their own fault.
Any volunteers?
Click to expand...
Click to collapse
having asked the same question myself here goes.
Download USPL and follow the instructions. they are very clear.
Download
extract
connect phone with minimum 50% battery
soft reset and once started up fully run the app by clicking on Rom Update utility
follow the process through once finished your device will restart.
once restarted you then can flash the rom of your choice
I used Black and Blue again ran the update utility and bingo.
dont forget that all data on your device will be lost so make sure you have back up of contacts etc in outlook on pc.
Finaly make sure you have Activesync 4.5
enjoy
AS STATED ALTHOUGH THIS WORKS YOU ALL DO IT AT YOUR OWN RISK
Id just like to know really is that how many people have done it without unlocking the device for o2 orbit uk. i have one and am not really willing to try it unless i know there are people out there that have tried it and it worked.
as there is no rom install file from o2 for this, there is no way bacj and bricked phone is the only way forward. id like not to brick my phone as i need it daily.
so, has anyone with a locked o2 device upgraded to WM6 successfully and which rom did you use if it worked.?
joey jojo said:
Id just like to know really is that how many people have done it without unlocking the device for o2 orbit uk. i have one and am not really willing to try it unless i know there are people out there that have tried it and it worked.
as there is no rom install file from o2 for this, there is no way bacj and bricked phone is the only way forward. id like not to brick my phone as i need it daily.
so, has anyone with a locked o2 device upgraded to WM6 successfully and which rom did you use if it worked.?
Click to expand...
Click to collapse
i have o2 uk orbit and all is well
pof said:
I created update package for this ROM in NBH format, so no risk of bricking when flashing it, just unzip & run RomUpgradeUtility.exe
Download here:
ARTE_WWE_WM6.zip​
NOTE: Before flashing you need to have Artemis USPL on your device.
Click to expand...
Click to collapse
Taken from Bepe's thread about the modified o2 German update. Basically you need to use the Artemis USPL program and then use the first link to install which I did successfully on a CID locked phone.
Thanks guys, but, unfortunately, the uspl thing does not work on my pc
Along with a few others I get the 'black screen' on my mdac3 then activesync disconnects and the rom loader throws up an error
Luckily my mdac3 survives through a soft reset
I think the idiots guide is not quite there yet
hi..
i have O2 uk orbit.. which is still locked, i fully charged the battery, completed a hard reset of the phone used the pof Artemis Update SPL (USPL) v.01 upgrade (wow what a brain box he is!) just in case it failed, so i could you use any NBH file to get you orbit to work again if i failed. Then used Bepe's WM6 os.nb file renamed it to windows.nb downloaded ATRE.zip unzipped the ARTE.zip file placed the windows.nb into the same directory, don't forget to edit UpgradeRom.bat file 0x3900000 to 0x3500000 with in the ATRE directory and copied and installed EnableRapi.cab to the phone. Reset it the phone and then started the UpgradeRom.bat! 12 mins later upgrade complete. Hard restart the phone.. Chewing nails by now... all went well did a soft reset of the phone before the O2 ExtROM autorun starts..
sorted, and did half way though a night shift at 3 am.. not bad at all!
crushuk said:
hi..
i have O2 uk orbit.. which is still locked, i fully charged the battery, completed a hard reset of the phone used the pof Artemis Update SPL (USPL) v.01 upgrade (wow what a brain box he is!) just in case it failed, so i could you use any NBH file to get you orbit to work again if i failed. Then used Bepe's WM6 os.nb file renamed it to windows.nb downloaded ATRE.zip unzipped the ARTE.zip file placed the windows.nb into the same directory, don't forget to edit UpgradeRom.bat file 0x3900000 to 0x3500000 with in the ATRE directory and copied and installed EnableRapi.cab to the phone. Reset it the phone and then started the UpgradeRom.bat! 12 mins later upgrade complete. Hard restart the phone.. Chewing nails by now... all went well did a soft reset of the phone before the O2 ExtROM autorun starts..
sorted, and did half way though a night shift at 3 am.. not bad at all!
Click to expand...
Click to collapse
Confused... is it really necessary to take all these steps? I thought that the only thing required is to run Pof's tool USPL, and after that run Romupdateutility.exe from the package in .nbh format (the link is just a few messages above yours). Please correct me when I'm wrong.
step by step guide
stunno said:
Any volunteers?
Click to expand...
Click to collapse
OK, I volunteered... This is a detailed list of steps how I installed a new ROM on my MDA Compact III (CID locked, at least I think so). It worked without any errors or problems. I used PDAVIET Black&Blue v2.0. It was my first flash on my Artemis, so I more than understand your need for step-by-step guide
1. download the file Artemis_USPL.zip
2. unpack into the folder c:\USPL
3. download the file ARTEMIS_Black_Blue_v2.zip
4. unpack into the folder c:\ROM
5. soft reset your phone and have it charged over 50% (I have it fully charged)
6. wait until the system starts on your Artemis
7. turn on flight mode (probably not necessary, but I wanted to minimize any risks)
8. connect your Artemis to PC with a USB cable
9. wait until ActiveSync icon in your tray (lower right corner of your windows desktop) turns from gray to green. If you connect your Artemis for the first time to PC, you do not need to set up synchronization, just click "cancel" on the first screen of "Synchronization Setup Wizard"
10. while ActiveSync icon is green, run c:\USPL\start_uspl.exe
11. a DOS screen will pop up with the text "Initializing: 0.." in the bottom indicating probably seconds from the start (it stopped around 70 in my case after about 1.5 min)
12. DOS screen disappears and PDA Phone ROM update utility pops up
13. at the same time, your Artemis turns blank (orange/green LED turns off as well)
14. tick the check box next to " I understand..." and then click Next
15. tick the check box next to " I completed..." and then click Next
16. a box saying "Verifying information on your PDA..." pops up
17. on the next screen click Update button
18. next screen says "Upgrade to ... image version 9.99" - click Next
19. Next screen says "You are now ready to update..." - click Next, a window with a blue progress bar appears with a text "Updating ROM image..", it quickly runs to 100%
20. next screen says "Congratulations! ..." - click Finish
21. your phone turns on and boots into your old system, however it should be CID unlocked now
22. your Active Sync should reestablish and icon turns green again
23. do not touch anything (phone or USB cable) and run C:\ROM\ROMUpdateUtility.exe (make sure activesync icon is green)
24. PDA Phone ROM Update utility window appears, tick the check box next to " I understand..." and then click Next
25. tick the check box next to " I completed..." and then click Next
26. a box saying "Verifying information on your PDA..." pops up
27. on next screen click Update button (says "Current information...")
28. next screen says "Upgrade to ... image version BnB2.0" - click Next
29. Next screen says "You are now ready to update..." - click Next
30. a window with a blue progress bar appears with a text "Updating ROM image..", your Artemis will have light gray screen with blue progress bar showing the progress of flashing - do not touch anything and wait (it took 2-3 minutes on my 3 years old PC)
31. next screen says "Congratulations! ..." - click Finish
32. your Artemis turns on and starts booting, you can disconnect it from PC now
33. the boot screen remains the same (T-Mobile in my case), so do not panic!! it is normal
34. wait until calibrate the screen appears, calibrate, choose time zone and you are ready to use your new OS
35. let me know if this manual was clear enough, whether it helped you and please suggest potential changes for improvement
Take care,
Dzim
i've just succesfully flashed my dutch CID-LOCKED MDA Compact 3 with this method, so i'd say it's reasonably fool-proof
A couple of questions before i take the plunge - if my t-mobile cmda iii is already CID unlocked, can i just go straight to the update rom part.
Also, is there any way of dumping my standard t-mobile rom first off? I'm having trouble trying to use itsutils due to the app lock.
Cheers Dzim!
Your instructions worked perfectly.
One very happy complete idiot here!
Furbious said:
A couple of questions before i take the plunge - if my t-mobile cmda iii is already CID unlocked, can i just go straight to the update rom part.
Also, is there any way of dumping my standard t-mobile rom first off? I'm having trouble trying to use itsutils due to the app lock.
Click to expand...
Click to collapse
There is a TMobile rom on here somewhere already, I just cant find it at the moment
My Compact 3 it’s death now. After pres voice commander button MDA start only to the boot loader. Can’t run complete system.
Pleas tell me. How can I write the new rom with WM5 or WM6 ?
OOPS! Working well apart from the "cant save word documents" bug!!
Just an update - to use the v1 or v2 black and blue, even though it is unlocked, you still need to use the supercid util.
Otherwise you get the rom update getting to 3% before crashing out to say the rom is corrupted.
I've now converted 2 other tmobile compact mda IIIs successfully, wm6 is much quicker
Yes, with my Compact was exactly as You say. Now is death. What I can do now to repair it.
big thanks to Dzim, used the idiots guide and now on wm6 =D
cheers!
PS: first post
Hi! Nemesis, try to connect your HTC to your pc in bootloader mode.
Lauch start_uspl.exe in USPL folder. Follow instruction on post N°9 by DZIM.
After USPL your HTC should reboot (maybe in bootloader mode only).
Launch the ROMUpdateUtility.exe in Black&Blue ROM v2 and follow instruction.
Thanks gguyaz
Pleas tell me.
Could I doing this upgrade with Windows Vista on my PC?

O2 Cosmo (Excalibur) ROM Update - How the Hell ?

Hello Experts,
i have read a lot of the Threads here, but i can't find a good information
about my O2 Cosmo. My Dash is Simlook free and SuperCID enabeld.
I found this instructions:
Tools you need:
===============
- HexWorkshop from http://www.bpsoft.com/downloads/-
the ROM of your choice
- Winzip or Winrar
- a valid UNL file for YOUR phone
Preparation:
============
a) install HexWorkshop and Winzip or Winrar on your pc
b) in explorer on pc, RIGHT click on the ROM of your choice and use: "Extract files to folder ..." from conext menu Now it will unpack all the files
c) in the new folder you will have ONE file like "HRUU_signed.NBH" (*.NBH) RIGHT click on the .NBH file and use: "Hex Edit with Hex Workshop" from context menu
d) You'll see on the 5th row EXCA20000 ==> !!! make it EXCA***** (5 stars) and save the file
e) Now RIGHT click on ROMUpdateUtility.exe and use: "Hex Edit with Hex Workshop" from conext menu
Search for word "BsaD5SeoA" (without quotes, case sensitive)
You'll find it around address 0x3FC6C ==> !!! replace "BsaD5SeoA" with "IMEICHECK" (without quotes) and save the file
ROM-Update:
===========
1) take SIM card and SD card OUT of the phone
2) Connect the phone running windows ce to the pc (normal way).
3) Completely Unlock your phone using our unlocker <== REALLY IMPORTANT
4) After phone is unlocked run unlocker (again) BUT when the unlocker ask for UNL file, remove the USB cable from the phone THEN press "Cancel" on the unlocker select file window (unlocker will close on PC). NOTE: The screen on the device will not show something usefull when in this mode. Most probably it is complete WHITE. !!THIS IS NORMAL!! Don't touch phone, let it like it is!
5) After you closed the unlocker, attach usb cable again (phone has still white screen)
6) start (the modified) ROMUpdateUtility.exe
7) when update finished and device started you will get a message: "Data Crashed, contact service provider" (!NO PANIC!) ==> Simply fix this problem by running the unlocker again and this time select the key file normal way (full unlock process again). In case you have problems please indicate the step letter/number which is not clear/not working for you. If you REALLY do it STEP by STEP exact like described you will have no problem.
Click to expand...
Click to collapse
When i edit the .NBH file, i get a "ERROR 270" message!
When i dont edit the .NBH file, i get a "Invalid Ventor - Error Message"
I try to install this ROM:
"RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.90_Ship.exe"
So my Dash is a German Device, and i want a German ROM, if it is possible!?
OK, i try to go manually in the Bootloader modus, disable ActiveSync for
USB Transfer...and run the RUU Rom...but it allways break down the flash
process at 4% !
...mmh...have i forget any info, that you can help me...i dont know?
Ah Yes...i read in the Thread:
"How to flash a new ROM to your Wizard... a little tutorial!"
Here the link to:http://forum.xda-developers.com/showthread.php?t=298613
But i can see anything on the starting screen, if my dash ist a G3 or G4,
on my start screen ist "ABSOLUTLY - NO - Information" about it!
In the "System Information" i found a RIL Nr. 2.0002 ...
So i think my dash is a IPL/SPL G3...but i dont know it really!
I dont know what i can do anymore, to update my device to WM6.0 or 6.1
Plz, if anyone know what i can do, to fix my problem, plz then tell it to me,
thank you very much, and forgive me about my bad english!
Ok, i test many times this tool "Excalibur USPL- CID BYPASS" ...and yesterday
it works suddenly...i dont know "why" it works, i have done the same, like
every time i try it, but yesterday my dash move to the needed "WHITE
Screen"! And so i able to run the Rom Update, and it works fine!
Ah yes, my Phone tell me i'm in "SuperCID" Mode...so "WHY" i must use
this "CID Bypass Tool" ....crazy??? Or is my Phone a Liar...?
I have now installed this Rom, it Works a bit faster i mean:
RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.90_Ship.exe
But it is the same Rom Vers, like my old O2-Cosmo Rom, WM5.0 (1) with
Future Pack. But i have now the HTC Splash Screen!
So i want now to install this Rom (with WM6.1) :
"NoThrills_WM61_GER_V3.exe"
This is a "Kaiser" Rom... "Warum eigentlich Kaiser, hat der Beckenbauer damit
was zu tun...*g*
But when i try to run again the "Excalibur USPL- CID BYPASS" tool, my
dash show me only the "Linux Monkey" (Pinguin) Screen and hang up the
Phone, so that i must remove the battery....
The "White Screen" (that is the Screnn you must have to flash your Rom),
will dont come anymore....i dont know how...??? I start this batch file,
"Uspl.bat" ... and follow the instructions....mmh....allways i get the Linux
Monkey Screen...and not the white screen, "WHY" ?
Anybody a hint, how i can move into the "White Screen" Modus?
And a Question, is this Kaiser Rom compatible to my HTC S620 ?
Please belive me, i read a lot here...but i cant figure out this..., this Forum
here is a bit confusing, on many Threads you can read other informations!
Plz anyone, tell me (who know it) how i move exactly in the White Boot Screen?
Thank you!
If I understand you right you flashed a rom from the HTC Kaiser on your Dash. That's Windows Mobile 6.1 Professional for Touch Screen Devices. You need a rom from this thread for your Dash, not the Kaiser thread. Those ROM's are specifically for that phone. I doubt they'd even work on other Touch Screen phones because of it has the radio (I believe Radio is like Drivers in Windows, I may be wrong.) for that phone. As to fix your problem. I have no clue. Maybe you can get lucky and reflash it with an Official Dash ROM for your phone, but better getting advice on that from one of the more experienced people here. I'm a bit of a newby when it comes to this phone stuff. Good luck...
drkfngthdragnlrd said:
If I understand you right you flashed a rom from the HTC Kaiser on your Dash. That's Windows Mobile 6.1 Professional for Touch Screen Devices. You need a rom from this thread for your Dash, not the Kaiser thread. Those ROM's are specifically for that phone. I doubt they'd even work on other Touch Screen phones because of it has the radio (I believe Radio is like Drivers in Windows, I may be wrong.) for that phone. As to fix your problem. I have no clue. Maybe you can get lucky and reflash it with an Official Dash ROM for your phone, but better getting advice on that from one of the more experienced people here. I'm a bit of a newby when it comes to this phone stuff. Good luck...
Click to expand...
Click to collapse
Thank you!
But "NO" i don't flash my HTC S620 wit a Kaiser Rom..."What a Luck" ...i try
to do it...and now im Happy that this have not work for me!
I actually install this Rom:
RUU_Excalibur_HTC_GER_1.11.407.2_4.1.13.28_02.63.9 0_Ship.exe
I have now understand, what is a Kaiser ROM, it is the Device Name, oh
Man...i'm so a dummy....haha...
But i have a success, i change my O2 Rom to a HTC Rom
The Question now is, how i move in the "WHITE BOOT SCREEN" ?
That i'm able to Update my Rom to a WM6.1, if posible, a German 6.1 Rom.
Is here a German WM6.1 Rom?
Is a WWE a Multilingual Rom, is in such ROMs German Language included?
And how i can remove the CID forever, so that im able to update a ROM
without a CID Bypass Bootloader?
Any ideas?
The thing is, ...this CID Bypass Bootloader work "ONCE" and now that
Bootloader dont work anymore...i dont know why...i get only the Linux
Pinguin Screen...and this is a "Hang up Screen" so that i must remove
the Battery, for a new start.
But i get nevermore the "White Boot Screen" ...how is this posible?
I do the same, like before i do...mmh...???
If I understand what's been said. You need to re-run the CID-Bypass anytime you reflash you phone. As for a German ROM. I am not sure. Ypu'd need to look around through the furom. You could try the "Seach" feature and see what you come up with.
drkfngthdragnlrd said:
If I understand what's been said. You need to re-run the CID-Bypass anytime you reflash you phone. As for a German ROM. I am not sure. Ypu'd need to look around through the furom. You could try the "Seach" feature and see what you come up with.
Click to expand...
Click to collapse
Thank you,
but i try to run the "CID Bypass" but the "CID Bypass" run every time
into the "Linux Pinguin Screen" ...(i think it is programed in Linux?)
But the same "CID Bypass Bootloader" - work - for me "once" !
But now, not ! I dont know why?
With this CID Bypass Bootloader, i flash my Q2 Rom into a HTC Rom !
But that was only possible, as my dash move with this "CID Bypass Bootloader"
INTO a "White Boot Screen"...!
But "HOW" this was possible...i dont know...now this CID Bypass Bootl.,
wont work anymore....
You know what i mean?
The same tool (CID Bypass) wont work anymore, it work one time only.
When i now try to run this CID Bypass, i get a "Linux Pinguin Screen" in
Black. So there is a little Linux Pinguin "Preloader" ...and then the Phone
have a SOD..."Stand of Death" you Guys call that so, i think so!?
To search here, is very strange for me....i get results of all Forums here!
That was the reason why i want to try the Kaiser Rom, while i search
here in the Excalibur Forum...so i had think so, that was wrong, you know!?
Sorry, my english is not good enough to tell exactly my expirience!
But Thank you for Advice!
Hum, does it still look like windows mobile? If so they may have just changed the load screen. Either way when you run the bypass program, there' one step that'll show a screen on the phone when in windows mobile itself and you must press the center soft button to "continue" and then it'll enter the white screen mode. Sometimes I forget this step and bounce through the steps missing that. If you can't get into windows mobile, try reflashing with your phones official ROM first. They don't require the white screen. There's also a way to enter the bootloader screen by holding down a button, I forget which, while you press power to turn the phone on.
drkfngthdragnlrd said:
Hum, does it still look like windows mobile? If so they may have just changed the load screen. Either way when you run the bypass program, there' one step that'll show a screen on the phone when in windows mobile itself and you must press the center soft button to "continue" and then it'll enter the white screen mode. Sometimes I forget this step and bounce through the steps missing that. If you can't get into windows mobile, try reflashing with your phones official ROM first. They don't require the white screen. There's also a way to enter the bootloader screen by holding down a button, I forget which, while you press power to turn the phone on.
Click to expand...
Click to collapse
...no no, this ROM runs great! I have no Problem with this Rom!
But i have found a Solution "Yeah" !
For all who want to flash a O2 Cosmo!
Try this Link: Click
Thanks to the Uploader, found it by searching!
The last in line: "Unlock_phone_files.zip" !
Follow the steps in the text document!
Work fine for me!
But when you want to flash, and you get a connection ERROR, remove
the USB cabel, and put it back on your Dash, and run then only the
"ROMUpdateUtility.exe" again and it will work.
(Your srceen are allways WHITE!!!)
I had flash for 10min the "RUU_Excalibur_SPL-1.11_UpgradeOnly.exe"
You must extract the exe file, and copy the *.nbh file to folder 3!
After you run the "Auto.bat" and the Connection Error, click finish,
remove the USB cabel, put it back on the dash and run again and only
the "ROMUpdateUtility.exe" !
All work fine!
Thank you Developers!

How to upgrade ROm with nbh file

As newbie on this, anyone please guide me step by step to upgrade my P3300 rom with nbh file. My device is unlock already with current ROM 5.2.1908 (build 18125.0.4.2).
The procedure is given in almost every thread. It's simple really. Is your SPL version anything other than 1.11.0000 or 1.11.cmon? If yes then your phone is not unlocked. Unlock your phone by running USPL from here or the updated USPL from here.
Check if the USPL has worked by checking your SPL number. During phone booting at the white HTC screen your SPL should show either 1.11.0000 ir 1.11.cmon.
If it does you are free to flash any ROM. Get the ROM of your choice, put your phone into bootloader mode by pressing the voice record, power key and reset button simultaenously for about 5 seconds till you see a three colored screen. Attach it with USB and flash the rom using RUU.
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
stacknickel said:
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
Click to expand...
Click to collapse
do u have only .nbh file or along with .nbh file any other files are there ?
generally along with the .nbh file there are other files like romupdateutuility.exe etc.,
download those files also and save those files into your PC.
after unlocking your device then staup the device with bootloader mode (three color screen)
connect the Device with the PC by USB cable.
in the device display u will a word USB (left bottom corner)
run the Romupdateutility from the PC...
the process will guide u next steps ...
after the completion u will have new OS
Last I would recommend tht u also upgrade you Radio ROM (this is responsible for all the communication functions of ur phone i.e. calls, GPS, WiFi etc) which will enhance the communication capabilities.
Radio ROMs Link : http://wiki.xda-developers.com/index..._RadioUpgrades.
Note : before flashing any ROM or upgrading the RADIO kindly CID unlock your device or you will end up the with bricked device .
You can download my ROMs, they come with the full package
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
your device not properly CID unlocked...
unlock the device properly with USPL...
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
As sixthsigma said, did you check if the phone is correctly unlocked? Is the SPL showing 1.11.0000 or 1.11.cmon?
Secondly, what OS are you flashing on? XP, Vista or Windows 7?
Hi Randythered, IPL 1.25.0001 and SPL 1.27.0000
I am using your ROM RtR Manila v1.0
using XP
Well, firstly thank you for wanting to try out my ROM
Secondly, you haven't unlocked your phone properly yet. The SPL must be 1.11.0000 or1.11.cmon, depending on which USPL you use.
strange... hv tried several time but w/o luck...
now I notice that it cut out after '70' and jump into 100 with disconnecting
any choices of other USPL instead of the one attached here?
Did you flash the old USPL or the new one which is nosize? It is preferable to install the old one first. And then go for the cmon nosize USPL if need be.
From a noob to a noob
Hi, heres the procedure for upgrading your rom put as noob friendly as i can put it.
WHAT YOU NEED
1. HTC Artemis p3300
2. computer running Windows XP with activesync installed
3. Usb cable to connect to computer
4. The new rom that you want to flash
5. And USPL which can be downloaded at this page http://forum.xda-developers.com/showthread.php?t=311403
NB: For most of the newer roms you will probably need the updated nosize version of uspl http://forum.xda-developers.com/showthread.php?t=521406
PREPARATION
NB: Anything you need to backup or keep from your device do it now.
NB: in some cases you may have to hard reset your device before it will take the flash
1. Extract Uspl to your desktop
2. Extract the rom you downloaded to your desktop
3. Remove your sim chip and memory card from your device
4. Reset your device and sync with windows xp
UPDATING
1. In the USPL folder run the program called "start_uspl" and let it do its thing in the dos window,in
my case it goes to 70 and then jumps to 100,if you have been watching your device screen you will
see the linux penguin for a few seconds and it will change to a white screen.
A window will popup on your computer, do as it requests, when finished it will reset your device.
Sync your device with your computer again.
2. In your downloaded rom folder you should find a file called "ROMUpdateUtility.exe" or "Ruu.exe", run
it and a window will popup, do as it requests.
Your device screen will go tri-color(red,green,blue) and the rom update will begin, wait till it
finishes and thats it.
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
stacknickel said:
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
Click to expand...
Click to collapse
same ting got me with my first rom thats why i thought to put it in, happy flashing (not in the naked way )
Lol I can't belive I forgot to tell you that!
It's ok. Thanks to u too randythered.
Do you have dedicate Manila in cab file?
Thank you, here you go!
sixthsigma said:
your device not properly CID unlocked...
unlock the device properly with USPL...
Click to expand...
Click to collapse
Sixthsigma...you said - "unlock the device properly with USPL..." - how do I do that?
I got the same error as mentioned when trying to flash using the numb3rs ROM:
http://thewingster.com/numb3rs.aspx
I ran the herald-uspl.exe file. and ended up with teh above error. My TMo Wing has the original ROM on it and the phone itself is probably unlocked. Ive had it for a year now. Do I need to call TMo to unlock or is there some app I can run to do this myself?
appreciate any help!
nevermind, it worked ok on the second attempt!

[GUIDE]How to Flash Your Vogue (CDMA Only!!!!)

Hi all!!
Ever since I got my Sprint Vogue, I have spent God only knows how many hours looking for and gathering information regarding this phone (flashing instructions, unlocking, SuperCID, etc). There are a few sites that have fairly comprehensive guides as to how to do this, but there are very few posts in the Vogue Section here at XDA-Developers.
Having said that, I figured I would create my own "How to Flash Your Vogue"-Thread. This is a multi-step process and I cannot emphasize the importance of following every step down to the "T", that is unless you are looking for a silicone-skinned brick...
Who is this guide for?
*Anyone with a CDMA version of the Touch. [highlight]That means no GSM[/highlight]
*Noobs and Seniors alike.
*People who have trouble flashing their devices.
*Anyone looking for links to more information.
*Curious people in general.
*Anyone willing to get rid of the nasty stock rom and looking for a newer and cleaner OS (notice that I never said more stable, so do not blame me afterwards ).
[highlight]Please keep in mind that there is always a chance of bricking your device with these procedures. I will not be in any way, shape, or form responsible if you damage your device while doing this.[/highlight]
Got your coffee? Alright, let's do this.
Step 1. Preparing the device
As with every phone, you have to make sure that you have the following things done before flashing:
* Battery charged at least 50%.
* All the necessary programs (see next post).
* Instructions handy.
Make sure that you back up all your information (contacts, e-mails, files).... essentially, anything that you would like to keep post-flashing. You can do this via Active Sync/Mobile Device Center or via third party software (PIM Backup is really good)...
You will have to reinstall every last piece of software in your device as it will be hard reset. Some programs may work if installed in a SD card directly, but a lot of them write things to the registry and copy files to the device, which they require to run. Long story short, keep all your cabs and exe files in a safe place so you can restore later if needed.
Step 2. Unlocking the Device (HardSPL)
Unlocking the device is done so that you can flash custom roms in your devices. The unlocker that you are about to download and use was provided by "ImCoKeMaN" at PPCGeeks. If you are interested in the full thread, please click here.
If you have read the above link, you will see two versions of the HardSPL (0.40 and 2.31). Simply use 2.31 as it works fine with most devices.
[highlight]To use this under Windows XP,[/highlight]
1. Connect your device to your computer and make sure it is synced with ActiveSync.
2. Download and extract the contents of the zip file, which is an exe. Let it run to completion. You will be prompted to disconnect and reconnect your device at one point in the process. Do it... don't worry
3. It will look like it is flashing a rom via a RUU. Do not disconnect the device after it is done!!!!!
4. Once it is done flashing, you will see a prompt that says that it will run exitbl. DO NOT DISCONNECT YOUR DEVICE. At this point, open ActiveSync, go to File>Connection Settings> Uncheck "Allow USB Connections". Continue following the on screen instructions and let it finish.
5. Go to bootloader once more to verify that it worked. You should see 2.31 CoKe MFG.
[highlight]To use this under Windows Vista/7 x64 (thanks jitajt),[/highlight]
jitajt said:
connect your device to WMDC (it's not necessary to set up device, just connect without setting up device)
then right click on the 2.31 unlocker and run as administrator
follow the directions, you will get an error about sleep.exe not being compatible with x64 but just hit ok and continue, (you will get about 10 of them)
then just keep following the directions in the command prompt and it will put your phone into bootloader then you have to disconnect and reconnect when it tells you to. and it will flash your phone and reset it. then your done you can close the command prompt and disconnect your phone.
I did it just like above and I have not had any problems.
Do this at your own risk as I am not responsible for your phone
Click to expand...
Click to collapse
Step 3. Flashing your Roms
The time has finally arrived. You sat down patiently through the unlocker and you are now ready to take the leap of faith into what you believe will bring your device to a new level of usefulness (also known as getting rid of that nasty, bloated, stock rom )
The process is relatively simple:
1. Download the RUU package from this post. I am only posting this because some cooks only post the rom nbh files rather than the whole package.
2. Go into the threads and look for whichever rom you prefer. Look at my signature to learn which one I am using. NFSFan (my current one) is by far the best one I have tried so far. You can download it from here
3. Put your device in bootloader mode and connect the device to the computer. [highlight]Once in bootloader, activesync will NOT see the device. If the RUU gives a connection error, try to run it with the devices in regular mode (with ActiveSync connected)[/highlight]
4. Open the Romupdateutility.exe and follow the steps.
5. Once it is done flashing the rom, disconnect it from the computer and hard reset it. To do this, simply hold "Send" + "End Call" +Stylus in the reset hole for about 3 seconds. It will prompt you to erase all the data and restore to factory defaults. Press "Enter", which is the center button in the directional pad. Once it is done, press "Send" to reboot.
Congratulations, you just flashed your first rom for Vogue
Step 4. SuperCID
This step can be skipped if you are not thinking of doing anything as far as your radio (such as flashing radios other than the ones intended for Vogue). This is also used to do other things such as modifying certain important things on your device such as the NV files, which is information that will not be discussed here. However, if you are interested in finding out more, simply google it, there is a ton of information out there.
Anyways, back to SuperCID... here is the procedure (thanks to hpnasik at mobile-files.com for the post)
1. Download the following special rom . This is an Alltel rom with radio 3.37. This was specially prepared to be able to reduce the Security Level of the device to level zero.
2. Download mtty since you will need it. Do not worry if you do not how to use it. You will have a step by step in this guide.
3. Flash the Alltel rom from above.
Now comes the fun part...
4. Disable USB in Connection Settings of Active Sync
5. Boot The Phone holding power button and camera button to enter bootloader.
6. Phone Will Display Serial in Bottom
7. Connect Phone to PC
8. Phone should Display USB instead of Serial in Bottom
9. start mtty.exe
10. Select All Default and Connect to USB in drop down box and Shoot the Following Commands (All Commands are case Sensitive)
11. run command rtask a : After this Command Phone will not Display any thing
12. run command echo_on : even though nothing is shown to screen
13. run command readCID : in Sprint it will display SPCS_001
14. run command writeCID 00000000 : Set CID Value to 00000000 replaces SPCS_001 in Sprint (This make PPC Radio Security Level to Zero)
15. run command readCID : This will Display the Update CID as 00000000
16. run Command retuoR : This will return to Original Boot Loader State
Congratulations, you just SuperCIDed your device. Original thread with the instructions can be found here if you are interested.
Step 5. Flashing your radio.
Now that your device has been SuperCIDed, you will have the opportunity to flash radios that have been ported to this device (ie. there is a version of the 3.42.40 radio for the Titan, which has been ported to the Vogue). There are two ways of doing this:
Way 1: Do it by flashing via RUU (same as with flashing a rom)
Way 2: Flash via microSD card. Simply put whichever radio that you wish to flash in the root of a 2GB or less microSD card formatted to fat32. Rename the radio to VOGUIMG.NBH and put your device in bootloader. The flashing will start by itself.
Way 3 (I know I said two ways...): There are a few stock roms that come with new radios. One of them can be downloaded directly from HTC and it is for the Sprint Touch. This one comes with Radio 3.42.30
The other one is for Bell Mobility and this one comes with Radio 3.42.50.
Why am I giving "Way 3" if the other two options seem much easier?? I have run into the problem where my device would not let me flash other radios than the one that I had. SD card method did not work and the RUU started out fine but quits at 8% rebooting my phone and displaying Error 328 in the RUU on the PC. Anyway, here are the links...
Sprint rom with radio 3.42.30
Bell rom with radio 3.42.50
Verizon Stock Rom
All Shipped Roms (All Carriers) - Thanks conflipper!
All Above Radios zipped
The newer radios perform a little better and give out better GPS signal (faster locks)....
Hang on a sec... did you just say GPS?!?!? But my Vogue does not have a GPS.... It does, just read a little further and be happy
Step 6. Enabling GPS, Returning to Stock, and Carrier Cabs
As I said before, there is a GPS hidden on your device. Now, if you are like me and went straight to the specs of the phone to confirm, you will probably try to call BS on this. Long story short, there are a few custom roms which have this "tweak" already implemented (like the one I am using from NFSFan). If you require some more info, I will post it later...
[highlight]Location must be on or else your GPS will not work. To activate it, go to Settings>Personal>Phone and change the Location setting to ON instead of 911 (thanks for pointing it out, th3lolz)[/highlight]
[highlight]For Verizon Users[/highlight]
br125 said:
For those of you with the official mr1 update from verizon that cannot get their gps working:
My xv6900 came with the official update and I got it working, it involves downgrading to a NON-GPS radio, then back to a gps radio...
go here: http://forum.xda-developers.com/showthread.php?t=533639
now the instructions are going to imply that you must load the unlocker before each flash... bs don't worry about that
1. flash the .40 unlocker
2. flash the non-gps rom (reset before customization)
3. flash the 2.31 unlocker
4. flash the vzw rom (reset before customization)
5. flash any custom rom or android rom
that's it, time consuming, but it works
*ignore the multiple flashing instructions, its completely unnecessary, I've never flashed more than once with no problem ever....
I also suggest keeping the vzw radio, but do as you will, I like the 3.37.38 radio.. ain't broke don't fix it
lastly, just make sure you RESET BEFORE THE CUSTOMIZATIONS RUN...... that is what locks your gps.
good luck!
ps. the verizon radio rom that is in that post is for the "leaked" 3.37.37 radio, I reccomend using the official update from verizon here for the 3.37.38 radio rom instead:
http://www.pcdphones.com/phone_downloads.aspx?bid=95&cid=1&mid=302&carrier=Verizon Wireless
RESET BEFORE CUSTOMIZATIONS
Click to expand...
Click to collapse
[highlight]How to Relock you phone[/highlight]
If, for whatever reason you need to return your phone for repair/replacement, you will need to relock it. To relock your phone, simply run the unlocker 0.40 and flash the stock rom of your carrier.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker.exe
[highlight]Carrier Cabs[/highlight]
Thanks to Codybear for gathering all of the cabs with settings for various carriers. But since the link went down, here is another one courtesy of LMiller1708
https://sites.google.com/site/vogueroms/vogue-files
This information was only gathered by me and I take no credit whatsoever other than trying to put it in a one stop thread. Thanks to the following people
Shadowmite
ImCoKeMaN
mindfrost
NFSFAN
Codybear
joshkoss
and a bunch of people that were involved in developing all this...
Thread sticky'd as requested
Peace,
Josh
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
dwigginstm said:
ok so im a noob n all at this but for some reason when i go to start the Vogue unlocker it tells me to connect my phone, when its already connected. Ive tried everything my even switched to an xp from vista but still no luck. Please help
Click to expand...
Click to collapse
How exciting!! My first victi...erh patient
Did you put the device in bootloader mode? If you did and it is connected to the PC, you should see USB on the screen of your device. Also, do you have ActiveSync on your XP machine? You will need it for the drivers on this step. Changing USB ports sometimes help as well. And one last thing, do not use a USB hub, go directly through the USB ports in your computer. Good luck!
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
yes i have activesync set up with the phone and pc, but when i put the phone in bootloader mode and connect it the pc recognizes it but not activesync. is there another program i can unlock the phone with?
dwigginstm said:
yes i have activesync installed xp, and yes it changes from serial to usb in bootloader mode. But once i connect it to the pc while in bootloader mode my computer recognizes just activesync doesnt, only when its on and not in bootloader mode will activesync recognize it...
Click to expand...
Click to collapse
Do not worry about ActiveSync. While you are in bootloader, the device is not running WM, which is why your computer only sees it as a USB device. This is perfectly fine. ActiveSync will not recognize it.
Please, follow the instructions in my post for unlocking. Read it thoroughly and try to understand it, else you will end up bricking your device.
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
dwigginstm said:
ok but when i begin the unlocking exe it tell me to connect the device to activesync, althought the only way activesync will notice it is if i take it out of bootmode. your help is appriciated
Click to expand...
Click to collapse
that is a message in the RUU. do not pay attention to it. good luck...
so i finally got the unlocker to start and it begins the ten minute process and stops then show a 262 error code ive done this over and over again
Let's go from the top. I just saw the message that you were talking about. The unlocker does ask for ActiveSync as you pointed out and it is asking you to connect the device to the computer. Then it asks for you to press any key when that is done. So, try that and you should see the word "initializing" with a dotted line getting longer for about 20 seconds. Do that.
The RUU will start up afterwards. The prompt will tell you that it is going to flash a new SPL, and if I am not mistaken that is where you are getting stuck.
Just out of curiosity, which version of the Vogue do you have? (Alltel, Bell, Verizon, Sprint, US Cellular)?
no internet
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
terrancextc said:
i just flashes my cell for the first time in with sprint NFSFAN's WM6.5 1.00 FINAL ROM worked great but for some reason my internet doesnt work i downloaded NFSFAN Sprint Provisioning but i dont know how to use it. It has a cople files SPRINT~1.000 and 000DUMMY and setup.xls
thanks in advance
Click to expand...
Click to collapse
You downloaded a cab. Simply put it in your SD card and run it by tapping on it. Don't unzip it...
Unlocker is not 64 bit compatible... grrr....

Sense 2.5 help

Hey I would like to have sense 2.5 on my tilt too, but i really have no clue where to download it or start, help plz
I've read all the howtos and I tried flashing a 2.5 rom i found(i think its the right kind) and I keep getting error 262
Did you flash hardspl? What rom are you trying to flash? I suggest trying energy rom leo.
If by flash you mean download and run it on my computer then yes and the energy leo is the one i tried
When I click on the leo customRUU I get "windows cannot acces the specified path device of file. you may not have the appropriate permission to access this file "
http://forum.xda-developers.com/showthread.php?t=550540
I alrdy read that a few times over
"Flashing via ActiveSync with USB Lead (thanks to OliNex)
1. Download HardSPL package from *HERE* and extract to an empty folder
2. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable and it must not be in Flight/Airplane mode (i.e. radio should be on)
3. NEW: Internet access is required as the program checks online for updates and license
4. Run Rhodium-HardSPL_V2_00R3.exe on PC, make sure it's launched from a local drive (not through network drive, etc.). XP requires Admin logon and Vista/Windows 7 will automatically prompt to allow it to run in Admin mode, allow it. If you get an AntiVirus warning please ignore it, it contains no harmful code (just used a packer to compress it)
5. Follow steps as prompted in the HardSPL program. If this is the first run of HardSPL on a device after Hard Reset, you must select Automatic Flash Mode (first button in Welcome Screen)
NOTE: You should usually go for Automatic Flash Mode. The Manual Flash option is only to be used as noted below and you must only attempt the Manual Mode option if Automatic Flash Mode or SSPL-Manual.exe already put device in black screen. Any other errors triggered while running in Autoflash Mode will have to be fixed as instructed in the error message.
6. It will ask you to wait while it prepares for the flashing, press OK
7. Now it should go through without any error messages, if one does pop up then follow the instructions included in the error text. If no specific instruction is shown then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred)
8. At this point the phone hopefully went to a black screen (reporting version as 1.01.C-SSPL only using "info 7" in mtty), this is the SSPL version, which is temporary. Then RUU will instantly launch
9. NOTE: When RUU says it will Hard Reset do not worry, it is not going to do that. Also when it says the flash will take 10 minutes ignore that, it will only take a minute or so
10. SPL flashes, device automatically reboots, job done"
So im here asking for help
did you download the package from "here" in the directions first and flash that before going onto a custom rom like nrg's?
yes i did.....
never ran into any problems myself so i dont know whats up but have you tried on another computer? flashed through sd card?
Dragonmaster0430 said:
Hey I would like to have sense 2.5 on my tilt too, but i really have no clue where to download it or start, help plz
Click to expand...
Click to collapse
Ok, which device are trying to flash? Does tilt too mean "Tilt 2" or "tilt also"? If you are talking about a Tilt, you are in the wrong forum. This is Tilt 2 (Touch Pro 2/Rhodium).
WillardZ said:
Ok, which device are trying to flash? Does tilt too mean "Tilt 2" or "tilt also"? If you are talking about a Tilt, you are in the wrong forum. This is Tilt 2 (Touch Pro 2/Rhodium).
Click to expand...
Click to collapse
Wow...i mean tilt 2 ... XD
Dragonmaster0430 said:
Hey I would like to have sense 2.5 on my tilt too, but i really have no clue where to download it or start, help plz
Click to expand...
Click to collapse
i had this pb a few time ago, and as I remember, I solved it just by changing the folder where RRU AND NBH files where. try installing from an other folder...don't know why it works for me

Categories

Resources