Related
Hi y'all,
i have a BT GPS receiver that i used with my Qtek 2020 (before this was stolen... ).
Now i have a XDA Exec from O2, but i am not able to set the receiver!
Anyone has any tip for me?
Thanks a lot...
...no one can help me out...??? Please...
Check out this guide and follow from after installing tomtom and you should get BT GPS working with exec, I did!!!
ps search term used was 'tomtom 5.1 guide'
hope this helps!
http://forum.xda-developers.com/viewtopic.php?t=28386
Hello,
first the bad news: not every bt-reciever is working...
but you should try this way:
Connection-Manager
Enable BT
Setting (Connection-Manager) BT-Settings
Tab devices and ad new partnership (be sure, BT-Reciever is on)
Pair it with your Universal (pin is usuall 0000)
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Now it should work!
Thanks for the tipo...now i don't have my GPS receiver with me...but tomorrow i will give it a try.
The only thing that i find strange is: when i try to set the outgoing port i find my BT receiver in a box, but when i try to set the incoming port i dont' find it anywhere.
Something wrong?
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
can anyone confirm if haicom-405 bt works with dopod 900?
Hustladave said:
Oh...and also...i use the software "GPS View" for the connection with the BT receiver...which port should i open (the COM4, the COM8 or another one?).
I ask you this because i have 10 COM ports available (from 1 to 10), but i cannot open all of them, because some tell me "COM porte error" when i try to open it.
Thanks for your help...
Click to expand...
Click to collapse
As I wrote before:
Tap Com-Ports: new outgoing Port (your BT-Reciever) set to com 4
Tap Com-Ports: new incomming port (your BT-Reciever) set to com 8
Best wishes
Teja
jona69 said:
can anyone confirm if haicom-405 bt works with dopod 900?
Click to expand...
Click to collapse
I follow the tips ...outgoing port (COM4 - which the only port can be used other failed to open), incoming port (COM8).
But it doesnt work with my Garmin10 .... which work well with my previous XDAIIs. Anyone use Garmin1o with Dopo900?
Thanks
Usually, there's no need to setup an ingoing COM port: my Holux 236 receiver, for instance, works perfectly paired with my Qtek 9000 and only the outgoing COM8 setup'd.
The only thing to pay attention for is that TomTom have to be v5.1 or above (better if v5.21), in order to work properly under Windows Mobile 5.0.
Well...in my previous XDAII worked perfectly using the software MAPSONIC and the GPS VIEWER with my BT receiver (and just setting the outgoing port).
I tried to do like Teja told me in his answer (setting the outgoing COM4 and the incoming COM8), but it still does not work.
I will try to get a TOMTOM 5.1 software to give it a try...
solved...and i don't need to setup the ingoing port...thanks for the tips
Hi there! I have MDA Pro from T-mobile (UK) and until now I couldn't set a COM port appart of COM0 port for BT-GPS...
Now have COM4 for outgoing port and tom tom once is connected after 5 seconds is disconnected and again after 5 seconds is connected and again is disconnected and again......
I am using TT 5.21
Help please
I have set the outgoing port on COM8, no ingoing port needed and it works fine...although i don't have TOMTOM!!!
Orange M5000 and BT GPS and TOMTOM 5.21
I thought I share this just in case there are other like me out there.
I had an Orange M2000 with tomtom 5.0 and 512MB SD card.
I installed TT5 as normal on the PDA but the maps on the 512MB SD card.
I just got an Orange M5000 which is XDA EXEC and could not install TOMTOM 5.0 from CD. The SETUP kept on crashing on XP PC.
Here is the solution:
1) Put the SD card with the maps in M5000
2) Did NOT install TT5 from CD but downloaded navupd521.exe from the tomtom site and installed this on M5000 fine.
NOTE: I did not have to copy CAB files. I just installed this as normal from my PC with the USB cable
3) TT installed fine but I could not get it to recognise the BT GPS
I used the instructions below from the forum:
a) Turn on BT GPS
b) on PDA goto BlueTooth seeting --> New Partnership and supply the password (0000) to pair it.
c) Then in Bluetooth settings select the COM PORTS tab
d) Select Incoming port and set to COM8
e) and again in COM PORTS tab select Outgoing ports and select COM4
f) Start TOMTOM and goto Preferences and find GPS Configuration and select OTHER GPS and select COM4
It works every time... ALL my FAvourites etc are still there so no need to type them again.
So far WM5 and TT5 rocks. I will be testing it on the road with my Plantronics BT headset soon. With my old M2000, usually when TT5 is on the M2000 CPU does not have the juice and Bluetooth devices die or stop responding. Also when I stopped TT5 application the BlueTooth stopped.
We will see how M5000 improves on M2000
Thax...
i believe you shouldnt have a problem running your headset and bluetooth GPS together.
when i had a blue angel i ran TT3 with my SonyErricson Car Kit and the TT3 together and made vioce calls at the same time and even now with the Universal i can do the same! run them both together!
only thing is that occasionaly the TT5 seems to be a little behind my actual location if i have made/received a call luckily by only 30-40 yards so can still use the screen to see where my turnings are.
has anyone else found that and got the cure....
thanks
Hi!
Is there a way to use the GPS receiver that is built into the Artemis as a GPS Device for Windows (XP or Vista).
Maybe over Bluetooth or USB / ActiveSync connection.
I tried to set up Bluetooth COM Ports so Incoming BT connections connect directly to the GPS COM port, but without success... no gps data was coming through.
Also I search for a small tool to test the receiver... just a compass or something.
regards,
Daniel
You cannot just "bridge" the GPS com port to your desktop OS via BT. The BT stack was never designed that way. All BT com ports you use must have a piece of software behind it to fill it with data, or otherwise they are just empty cans.
In your case, you need a GPS splitter to get gps signals from the GPS com port, and then repeat it to a BT com port so that the other end can receive such signal. That will provide a working bridge for your data.
Try software such as gpsgate that works as described above.
Hello, you can try GPS2Blue is a little free program that will let you use your Artemis as a GPS.
You can find it here: http://users.skynet.be/hofinger/GPS2Blue.html
Enjoy.
i got myself GPS2Blue and installed it.
My problem now is, that i cannot set up a BT COM port!
I have the (german) B&Bv3 ROM (WM6). In Bluetooth Settings in the "COM Ports"-Tab. It says "Tap on 'New outgoing port' ..." but theres no button or something. Just the describing text and an empty ListBox.
since I cannot set up my COM port, GPS2Blue won't swich on right?
So... is this a WM6 bug or a B&B Bug or my brain-bug
Setting up COM ports in my firmware WM5 OS worked just fine.
Thanks you guys for the info!
but what to do now?
GPSgate can do what you want (but it is not free)
gpsgate can set up bluetooth com ports? i dont think so
this is not a gps problem anymore!
i posted a new thread for my new problem:
http://forum.xda-developers.com/showthread.php?t=315687
GPSGate can do it!!
Use this is the registration key:AmzeaBjw
Then your Artemis can pass GPS information to your PC through Bluetooth
Fransons GPS Gate will enable the sharing of GPS position to a number of different types of device, I am not too sure about posting a registration key for purchased software as these are specific to an individual user??? - Mike
I have been trying all weekend to Sync my 8525 and my HP laptop via Bluetooth and it will not work! They are both paired and I can do just about everything with them both but sync with ActiveSync. I can use the phone as a modem, transfer files, use the laptop as an external stereo speaker and as a speaker phone but it will not sync with freakin' Activesync! Both the Laptop and the 8525 serial ports are set at Com8. When attempting to sync via bluetooth on the phones active sync all I get is:
"Cannot connect using Bluetooth to a PC that supports ActiveSync. You may be out of range. Would you like to create a Bluetooth partnership with a different PC?"
Oh my LORD!! This is becoming soooo anoying! I have tried searching here and through Google, I have tried just about everything to get this crap to work and so far NOTHING!!!!
I am at wits end! Please if you can help it would save my sanity!
-Cingular 8525
-Windows Mobile 6 Professional (OEM Rom downloaded from HTC website)
-Rom version 3.62.502.3
-Radio version 1.54.07.00
Thank You!
acuraman2004 said:
Both the Laptop and the 8525 serial ports are set at Com8.
Click to expand...
Click to collapse
Looks wrong to me, as PDA's COM8 is not laptop's COM8. I suggest you delete all the serial ports, and delete the partnership itself on both PDA and laptop. Then let ActiveSync establish it back as it wants.
Koterpillar said:
Looks wrong to me, as PDA's COM8 is not laptop's COM8. I suggest you delete all the serial ports, and delete the partnership itself on both PDA and laptop. Then let ActiveSync establish it back as it wants.
Click to expand...
Click to collapse
I have tried that before, and it still gave me the same message when trying
to sync. The laptop usually sets the com port to 8 and the phone sets the com port to 0, however this does not seem to sync. I will try it again tonight to see if maybe I missed something. Thank you for your suggestion.
If anyone else has any ideas I would love to try them.
Thank You!
For what it's worth, I'm able to sync my 8525 via Bluetooth ActiveSync with my Windows XP Professional notebook. It took a little finegaling, but I was able to make it happen. Unfortunately, the notebook is at home, and the phone is not allowed into my office. If you don't get it resolved by this evening, I'll try to post my settings after I get home.
Joe
marinerjoe said:
For what it's worth, I'm able to sync my 8525 via Bluetooth ActiveSync with my Windows XP Professional notebook. It took a little finegaling, but I was able to make it happen. Unfortunately, the notebook is at home, and the phone is not allowed into my office. If you don't get it resolved by this evening, I'll try to post my settings after I get home.
Joe
Click to expand...
Click to collapse
Thank you very much, from one Joe to another!
So......Huston we still have a problem. Deleting the two devices and repairing did not seem to correct the issue.
Hmmm. I have experienced this before, and have fixed it....somehow. Sorry. I have a Dell laptop (yeah ok, wotever!). Established activesync partnership via usb to start. Told phone to find new BT gear, paired with laptop, ticked every box that the laptop presented, including 'allow device to access activesync service'. In BT settings, laptop has activesync box ticked in list of services available. To connect, I go into comm manager, turn on activesync, menu, connect via bluetooth. All sweet. Running WM6.1, had it working on most of the WM6 roms too.
what bluetooth stack are you using on you laptop?
Umm.. would that be 'WIDCOMM Bluetooth Software 5.0.1.2609'? Dunno - whatever is installed on the Dell Inspiron 6400. Would be happy to provide any further info, if you can tell me exactly what it is you want and where I find it....
XtreMe_G said:
what bluetooth stack are you using on you laptop?
Click to expand...
Click to collapse
Does this help any?
ads2112 said:
Umm.. would that be 'WIDCOMM Bluetooth Software 5.0.1.2609'? Dunno - whatever is installed on the Dell Inspiron 6400. Would be happy to provide any further info, if you can tell me exactly what it is you want and where I find it....
Click to expand...
Click to collapse
oh, sorry ads2112, should have been clearer, i was asking acuraman2004 wat his bluetooth stack was, not you.......you dont have any problems with ur bluetooth and activesync right?
XtreMe_G said:
oh, sorry ads2112, should have been clearer, i was asking acuraman2004 wat his bluetooth stack was, not you.......you dont have any problems with ur bluetooth and activesync right?
Click to expand...
Click to collapse
You know what I am not sure as to where that information would be located on the laptop. I will search for the information once I get home from work and post it. Thank you for the reply.
Joe
acuraman2004 said:
I have been trying all weekend to Sync my 8525 and my HP laptop via Bluetooth and it will not work! They are both paired and I can do just about everything with them both but sync with ActiveSync. I can use the phone as a modem, transfer files, use the laptop as an external stereo speaker and as a speaker phone but it will not sync with freakin' Activesync! Both the Laptop and the 8525 serial ports are set at Com8. When attempting to sync via bluetooth on the phones active sync all I get is:
"Cannot connect using Bluetooth to a PC that supports ActiveSync. You may be out of range. Would you like to create a Bluetooth partnership with a different PC?"
Oh my LORD!! This is becoming soooo anoying! I have tried searching here and through Google, I have tried just about everything to get this crap to work and so far NOTHING!!!!
I am at wits end! Please if you can help it would save my sanity!
-Cingular 8525
-Windows Mobile 6 Professional (OEM Rom downloaded from HTC website)
-Rom version 3.62.502.3
-Radio version 1.54.07.00
Thank You!
Click to expand...
Click to collapse
Didn't have quite the same problem that you are having, but was having trouble. I found these instructions and took care of mine right away. The author, and the link to the site are listed in the instructions. I copied them to notepad so as not to lose them. Hopefully this will work for you.
BlueTooth Sync
I got my bluetooth to work by following Hazymat's guide: Here (http://www.modaco.com/Active_Sync_over_BlueSoleil_Blutooth-t232696.html) Excerpt:
Thanx to a Hazymat over on xda-dev I managed to get it all working, his guide, for anyone else finding this:-
1) On your computer, go into bluetooth settings. Check bluetooth is ON and set to discoverable. Add an incoming COM port, eg. COM5.
2) On ActiveSync on your computer, go into connection settings. Tick all the boxes. If the COM port is greyed out, untick it, close the settings box, go back in, now tick it and set the COM port to eg. COM5.
3) On the K Jam go into bluetooth settings, and remove the connection to your computer.
4) On your K Jam go into ActiveSync, click 'menu' > 'connect via bluetooth' then you should see a message saying 'cannot find an existing bluetooth partnership with a PC that supports ActiveSync. Would you like to set up a partnership now?'
5) Click YES - you are taken to the Bluetooth settings screen.
6) Now click 'new partnership. As soon as you do this, the K Jam will search, and as long as your computer has bluetooth discoverable turned on, your computer will eventually be displayed. Check the computer name showing on the K Jam is the same as the name you gave the bluetooth profile on your computer.
7) On K Jam, click your computer name then NEXT.
Now enter a passcode - any four digit number (remember it) then next
8) When you do this, your computer will pop up with a message saying "a bluetooth device is requesting authorisation". Open this message and type in the code that you gave the K Jam. The next screen on the computer will tell you that it was successful - click FINISH.
9) Back on the K Jam, the screen will now be showing the services available. AS LONG AS YOU FOLLOWED STEP 1 and 2, ActiveSync will be an option, and you need to tick this and press FINISH on the K Jam.
10) Close bluetooth settings, now in ActiveSync screen click MENU > Connect via bluetooth. Your ActiveSync program on the computer should eventually pop up and connect.
The only port you worry about is the incoming pc one. Active Synch does the rest. You must see acitivesync as a service when you connect. I did not see it until I updated my Toshiba Bluetooth stack from thier website. Creating other ports can stop the synch from working.
Steve Sharp said:
Didn't have quite the same problem that you are having, but was having trouble. I found these instructions and took care of mine right away. The author, and the link to the site are listed in the instructions. I copied them to notepad so as not to lose them. Hopefully this will work for you.
BlueTooth Sync
I got my bluetooth to work by following Hazymat's guide: Here (http://www.modaco.com/Active_Sync_over_BlueSoleil_Blutooth-t232696.html) Excerpt:
Thanx to a Hazymat over on xda-dev I managed to get it all working, his guide, for anyone else finding this:-
1) On your computer, go into bluetooth settings. Check bluetooth is ON and set to discoverable. Add an incoming COM port, eg. COM5.
2) On ActiveSync on your computer, go into connection settings. Tick all the boxes. If the COM port is greyed out, untick it, close the settings box, go back in, now tick it and set the COM port to eg. COM5.
3) On the K Jam go into bluetooth settings, and remove the connection to your computer.
4) On your K Jam go into ActiveSync, click 'menu' > 'connect via bluetooth' then you should see a message saying 'cannot find an existing bluetooth partnership with a PC that supports ActiveSync. Would you like to set up a partnership now?'
5) Click YES - you are taken to the Bluetooth settings screen.
6) Now click 'new partnership. As soon as you do this, the K Jam will search, and as long as your computer has bluetooth discoverable turned on, your computer will eventually be displayed. Check the computer name showing on the K Jam is the same as the name you gave the bluetooth profile on your computer.
7) On K Jam, click your computer name then NEXT.
Now enter a passcode - any four digit number (remember it) then next
8) When you do this, your computer will pop up with a message saying "a bluetooth device is requesting authorisation". Open this message and type in the code that you gave the K Jam. The next screen on the computer will tell you that it was successful - click FINISH.
9) Back on the K Jam, the screen will now be showing the services available. AS LONG AS YOU FOLLOWED STEP 1 and 2, ActiveSync will be an option, and you need to tick this and press FINISH on the K Jam.
10) Close bluetooth settings, now in ActiveSync screen click MENU > Connect via bluetooth. Your ActiveSync program on the computer should eventually pop up and connect.
The only port you worry about is the incoming pc one. Active Synch does the rest. You must see acitivesync as a service when you connect. I did not see it until I updated my Toshiba Bluetooth stack from thier website. Creating other ports can stop the synch from working.
Click to expand...
Click to collapse
Dude thank you! I will try that as soon as I get home!
I have it working on my desktop PC in front of me. Here's my setup:
PC:
IVT BlueSoleil v5 I think (the one that costs money but has a new slick interface)
Device Name: PokerPro
Device Type: Desktop
Accessibility: Allow other Bluetooth devices to find this device, Allow other Bluetooth devices to connect to this device
Services: Bluetooth Serial Port (COM4), Bluetooth Serial Port (COM5), Bluetooth Advanced Audio, Bluetooth Object Push, Bluetooth File Transfer, Bluetooth Personal Area Network. All have Security On (i.e. a secure connection).
Serial Ports: COM4: Direction Incoming. COM5: Direction Incoming.
Microsoft ActiveSync:
Connection Settings:
Allow USB connections
Allow connections to one of the following: COM4
This computer is connected to: Automatic
Open ActiveSync when device connects
I >don't< have "Allow wireless connection on device when connected to the desktop" set.
On my Phone:
Running WM6 (Windows CE 5.2.1933) (note not WM6.1) and Schap's 4.01 full rom
Bluetooth device name: "Dir Someone" (my name). I don't have OBEX enabled.
Within the Bluetooth settings:
PokerPro shows up as a device. If I select it, it shows Wireless Stereo (not ticked) and ActiveSync (ticked). This is the important bit - ActiveSync needs to show up as a service under your PC paired connection.
Mode: Turn On Bluetooth is ticked, but "Make device visible to other devices" is not ticked.
COM Ports: I don't have anything there aside from "New Outgoing Port".
FTP: Enable Bluetooth Explorer is ticked
Security: Authentication (Passkey) required is not ticked.
ActiveSync: I have "Synchronise all PCs using this connection" ticked, with the default " 'USB " selected.
When I select "Connect via Bluetooth", I get a message on my desktop saying the phone has connected, and ActiveSync turns green and starts spinning.
If I recall correctly, it took me a couple of goes before the ActiveSync service appeared under the PC paired connection (the bit in italics above). I don't recall how I got that working but it was just a matter of deleting the connection and letting them discover each other again I think.
I did a bunch of research and found a few articles that I read at the time, but because I'm using BlueSoleil it was slightly different for my setup. But you can get the general idea of what you need to do here.
Check My post here, it is on the butoom of the page!!
http://forum.xda-developers.com/showthread.php?t=347472
hth,
Stuart
Steve Sharp said:
The only port you worry about is the incoming pc one. Active Synch does the rest. You must see acitivesync as a service when you connect. I did not see it until I updated my Toshiba Bluetooth stack from thier website. Creating other ports can stop the synch from working.
Click to expand...
Click to collapse
I don't see "Activesync as a service" on my Cingular 8525. now AT&T, and I have their latest software. How do I get an update?
Steve Sharp said:
Didn't have quite the same problem that you are having, but was having trouble. I found these instructions and took care of mine right away. The author, and the link to the site are listed in the instructions. I copied them to notepad so as not to lose them. Hopefully this will work for you.
BlueTooth Sync
I got my bluetooth to work by following Hazymat's guide: Here (http://www.modaco.com/Active_Sync_over_BlueSoleil_Blutooth-t232696.html) Excerpt:
Thanx to a Hazymat over on xda-dev I managed to get it all working, his guide, for anyone else finding this:-
1) On your computer, go into bluetooth settings. Check bluetooth is ON and set to discoverable. Add an incoming COM port, eg. COM5.
2) On ActiveSync on your computer, go into connection settings. Tick all the boxes. If the COM port is greyed out, untick it, close the settings box, go back in, now tick it and set the COM port to eg. COM5.
3) On the K Jam go into bluetooth settings, and remove the connection to your computer.
4) On your K Jam go into ActiveSync, click 'menu' > 'connect via bluetooth' then you should see a message saying 'cannot find an existing bluetooth partnership with a PC that supports ActiveSync. Would you like to set up a partnership now?'
5) Click YES - you are taken to the Bluetooth settings screen.
6) Now click 'new partnership. As soon as you do this, the K Jam will search, and as long as your computer has bluetooth discoverable turned on, your computer will eventually be displayed. Check the computer name showing on the K Jam is the same as the name you gave the bluetooth profile on your computer.
7) On K Jam, click your computer name then NEXT.
Now enter a passcode - any four digit number (remember it) then next
8) When you do this, your computer will pop up with a message saying "a bluetooth device is requesting authorisation". Open this message and type in the code that you gave the K Jam. The next screen on the computer will tell you that it was successful - click FINISH.
9) Back on the K Jam, the screen will now be showing the services available. AS LONG AS YOU FOLLOWED STEP 1 and 2, ActiveSync will be an option, and you need to tick this and press FINISH on the K Jam.
10) Close bluetooth settings, now in ActiveSync screen click MENU > Connect via bluetooth. Your ActiveSync program on the computer should eventually pop up and connect.
The only port you worry about is the incoming pc one. Active Synch does the rest. You must see acitivesync as a service when you connect. I did not see it until I updated my Toshiba Bluetooth stack from thier website. Creating other ports can stop the synch from working.
Click to expand...
Click to collapse
Steve Sharp - thanks a TON for this post...I've been trying to get Activesync to work on my Tilt for about 3 weeks now.
thanks!
Hello fellows i need a little bit of your expertise, i cant sync with activesync via bluetooth, i´ve searched a lot in forums but i just cant find the answer, jiji
hopefully one of you guys can help me
tnx
chinito74 said:
Hello fellows i need a little bit of your expertise, i cant sync with activesync via bluetooth, i´ve searched a lot in forums but i just cant find the answer, jiji
hopefully one of you guys can help me
tnx
Click to expand...
Click to collapse
We need more specifics to your issue, as there are several solutions. depending on which bluetooth stack you're using.
SO tell us which OS you're using on your PC (or MAC)
And tell us which bluetooth stack (drivers) you're using so we can give you the help you need
i have windows xp sp2 and the bt is dell 355 + EDR thank you
chinito74 said:
i have windows xp sp2 and the bt is dell 355 + EDR thank you
Click to expand...
Click to collapse
Do you know what COM ports (COM ports numbers) for serial connections the bluetooth stack created. The reason why i ask is, if you know which virtual serial COM ports your bluetooth stack created (ex: COM Port 3, COM Port 4, COM Port 5) and which com port number your device is assigned when you are paired with your PC, then you can go to connection settings in activeSync on your PC and select conection via com port and in the dropdown, match the COM port your device uses when connected to your PC.
Then the next time you connect your phone to your PC via bluetooth, in the services section of your phone (after it scans your PC for services) one of those services should say "Activesync" when you check that and press OK you should be able to freely connect via bluetooth
ok, im gonna do that right now
tnx
in my phone services it appears activesync, but it does not connect, i have in the port com19 and in activesync i have it too but it just doesnt connect
chinito74 said:
in my phone services it appears activesync, but it does not connect, i have in the port com19 and in activesync i have it too but it just doesnt connect
Click to expand...
Click to collapse
You need to make the port on activesync either 6 or 7 for some reason those were the only two ports for me that appear in WM I am using 6.1 now. Also are you sure that the computer and the phone are both set up to be "visible" to each other? When you do a bluetooth scan from the computer without using activesync can you see the phone? On the phone you just turn on visibility after you enable bluetooth. On your computer I am not sure. Then once they have both established a connection you should be able to see the phone then setup your comports and select activesync as a service. This should enable you to sync bluetooth by selecting it in the menu from activesync. The problem that I am having myself is that when I try to sync the phone between my laptop work--and home the internet explorer favorites get messed up and i am getting an activesync error between files and favorites. What I have been doing is deleting the device and starting fresh however this sucks but at least i always have a backup either the laptop or the desktop
they are both visible, the problem that i have is that i cant use a 6 or 7 port inmy laptop, all the ports that i can make are 14,15,16 etc. so in my computer i cant open the 6 or 7 port
so its pretty crazy
Heres what you do
chinito74 said:
they are both visible, the problem that i have is that i cant use a 6 or 7 port inmy laptop, all the ports that i can make are 14,15,16 etc. so in my computer i cant open the 6 or 7 port
so its pretty crazy
Click to expand...
Click to collapse
Can you use the soleil drivers they have always worked well for me i to have had that problem. I ended up deleting everything and starting form scratch that fixed the problem. And yes that means the drivers on the computer. Also make sure that your not running the dell driver(might be toshiba stack) and the windows drivers this will cause conflict.
I am also having all sorts of bs with the Toshiba BT stack... need to find some compatable drivers.
so the thing is, i have to uninstall de dell driver and install a bluesoleil driver???
where do i find it?
i´ve already downloaded a bluesoleil driver but it didnt work
Is it possible to use a Touch Pro2 GPS on a laptop via bluetooth?
I wouldnt bother. You can probably get a gps reciever for your comp for pretty cheap. Then you wouldnt have to use your phone at all. Using your phone as a gps reciever and sending the signal to your laptop might run your phones battery dead faster, so if you were gonna use your phone as gps reciever, youd probly want to use usb rather than bluetooth, then the phone is charging and you have your bluetooth freed up for phone calls. But I would still suggest a reciever for your laptop, you wouldnt have to bother hooking your phone up n setting everything up every time you want to use gps
But yes i believe it is possible, Im pretty sure I saw a program for windows phones somewhere, that did send the phones gps info thru bluetooth to comp
It is called GPS2Blue and I never had any luck with it on bluetooth, but have via USB.
i just tried gps2blue again after years , now with rhodium and could get to work both tcp -> com and bluetooth -> com
WORKS GREAT with garmin on my tablet pc. and garmin-pc is even kind of made the way to use it on touch screens.
what do you have for a software?
here's what I have done:
cable:
on PC, install the Czech program called 'virtual serial port for tcp/ip'
Instructions where to get it and how to set it are here: http://users.skynet.be/hofinger/GPS2BlueFAQ.html#USB
on pda in gps2blue check TCP and choose com4 (or your gps SW EMULATED com port)
in gps program on pc choose to connect to the com port you just created with 'virtual serial port'
bluetooth:
choose com2 in gps2blue and click ON, rhodium's bluetooth manager should popup asking what to do, create a new port for your PC and go.
there is a little mess with this, it created two com2 ports on pda, till one was asking for a pairing code, the other just get connected. And is not showing them in list, or sometimes showing one, but then not showing activesync port. But nevermind. it's working.