Hello!
I can`t get connect whit activesync any more when I get a wrong rom for my wallaby device!
It have been nice if any body can send me a wallaby 1010 rom mmc/sd file??
Hope for reply!
http://www.romkitchen.de/
make a rom and use xdatools to put it on a sdcard
when a rom is places on a sd card it cant be copied or even read by a sdcard reader
Hi all, flashing my last rom, I seen that the device wasn't upgraded, but old os remained into it...
I used mtty and task 32 : leve 0
task 28 says that os not found in memory
task 2a and info 8 tell me that all blocks are bad...
the device stasrt, windows runs, only, now I cannot reflash with other rom..
some helps??? suggestions???
bye!
ervius said:
Hi all, flashing my last rom, I seen that the device wasn't upgraded, but old os remained into it...
I used mtty and task 32 : leve 0
task 28 says that os not found in memory
task 2a and info 8 tell me that all blocks are bad...
the device stasrt, windows runs, only, now I cannot reflash with other rom..
some helps??? suggestions???
bye!
Click to expand...
Click to collapse
ok, I've the solution, strange, but thrue.
I buyed yesterday a beautyfull, new minisd "4Gb", mounted it, and I discovered that if I run mtty with the 4Gb minisd into device, all blocks are bad
the rom wasn't updated into device if I flash one...
without minisd mtty give me all blocks ok, and flashing other rom, it will be uploaded into device...
ok, this is my cas, good also if someone have same problem, but my question now is, why with last 2Gb minisd this problem didn't present???
I flashed hundreds of rom with minisd iside and all ok...
my my new good, beautifull minisd 4Gb I spent a lot of time today to understand why all block were bad, this is the answer...
bye!
but the question still rests... why whit 2Gb sd all is ok, and with the 4Gb one not?!?!?!?
could this be part of the problem with ppl not being able to flash new radios to their device?
*sorry double post*
4Gb SD card MUST be a SDHC card, and these run on FAT32.... i think that might cause all problems...
Moaske said:
4Gb SD card MUST be a SDHC card, and these run on FAT32.... i think that might cause all problems...
Click to expand...
Click to collapse
maybe, only I know that from yesterday I flashed 5 times again my ppc with different roms and all is ok if I remove it from slot!
ervius said:
but the question still rests... why whit 2Gb sd all is ok, and with the 4Gb one not?!?!?!?
Click to expand...
Click to collapse
It didn't surprise me. To read files from the SD card, you need a hardware "driver" to communicate to the hardware and to understand the layout of the card, both physically - the SD/SDHC format; and logically, the file system on the card.
Remember, there is a distinction between the OS and the firmware - what an OS can do DOESN'T necessary mean that what a firmware can do, vice versa. Think it as the BIOS of your computer against your installed OS.
In this case, your WM6 can read SDHC because there's a SDHC driver in the OS. When you are doing an flash, all the vital functions that are needed are provided by SPL. If the SPL don't have the necessary "driver" - to read the SDHC, it will naturally bails out of the operations.
It's by design and is more or less expected. Period. Unless HTC is going to "update" their SPL to support SDHC as well, but who knows.
ww2250 said:
It didn't surprise me. To read files from the SD card, you need a hardware "driver" to communicate to the hardware and to understand the layout of the card, both physically - the SD/SDHC format; and logically, the file system on the card.
Remember, there is a distinction between the OS and the firmware - what an OS can do DOESN'T necessary mean that what a firmware can do, vice versa. Think it as the BIOS of your computer against your installed OS.
In this case, your WM6 can read SDHC because there's a SDHC driver in the OS. When you are doing an flash, all the vital functions that are needed are provided by SPL. If the SPL don't have the necessary "driver" - to read the SDHC, it will naturally bails out of the operations.
It's by design and is more or less expected. Period. Unless HTC is going to "update" their SPL to support SDHC as well, but who knows.
Click to expand...
Click to collapse
ok, good answer!!
I know now...
I suffered the problem of bad blocks you mention with a defective 4GB mini SD (TopRam) and reported it in Pof's thread (unlock) two months ago. I was about throwing one SPV M700 out of the window. Hopefully, I removed the card at the last minute. The result was the same as you describe: no way to flash a new ROM. Partial flash seemed to work but then I realized the previous version was still there. Wen trying to flash the OS section in the rom, the Trini faded off.
I have had recently had another problem trying to update Radio Rom with no success (no mini SD and no SIM this time). I had Olipro's Spl v1.3. I installed Olipr's Spl v1.2 back (with SSPL) and could upgrade the Radio Rom.
Benzin said:
I have had recently had another problem trying to update Radio Rom with no success (no mini SD and no SIM this time). I had Olipro's Spl v1.3. I installed Olipr's Spl v1.2 back (with SSPL) and could upgrade the Radio Rom.
Click to expand...
Click to collapse
I can confirm this.
My touchpad did not response correct so i decide to go back to the offical HTC ROM. The flashprocess finished at 100% with no error. After a reboot i can see that he radio was not updated.
After i go back to Hard-Spl 1.20 the radio rom i can flash the radio and the trinity accept it.
i have htc p3300 i have finished upgrade dis rom WM6.1 htc p3300achilles_ROM_ver_3_YouTube.1.321C02 after upgade finished my battery drain faster den i plan to upgrade radio rom, ARTEMIS_RADIO_3.39.90 it stuck in 79% but right now i got only searching for sd card then boot loader mode i have been seen lots of thread in dis forum i got only suggestion to run original htc shiped rom but da problem is when i upgrade original htc rom i got 274 error again and again i cant upgrade the original rom please help me urgent am upset
sometimes i get bootloader mode sometime i cant get,in begining searching for sd card den i get bootloader mode, is there any way to flash rom through sd card?i thought my battery is lessthan 50% how can i charge my battery in bootloader mode plz give me the solution.
If you are in bootloader you don't need 50% of battery.
Just flash the ROM.
See here for Sd-card flashing: http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
thank you for ur reply, i have rename .nbh file and put into sd card when i start phone first i get searching for sd card, den searching for sd content after 20 minutes its back to 3 colour bootscreen any solution?
thanking you.
Are you trying to do it with a SDHC card?
no just i have normal 1gb and 128mb micro sd card, first i try in 1gb card den i try 128mb card still i havnt upgrade ruu its first searching for sd card den searching sd contents datz it after dat pda is automatically turned off i do no y, how can i find SDHC card normal sd card?
yet no replies urgently required pleaseeee
my artemis always in bootloader mode i cant flash original rom also which rom i have to flash? everyday am trying to upgrade its shows 0% then upgrade error (266) and i cant sd flash also just searching for sd card den checking sd content and back to bootloader mode how many files i have to copy in sd card? am waiting for ur kind repleis thank u.
similar problem
I have some problems with my ARTEMIS P3300 (arte 100).
problem : I can't flash HTC WM6 english from http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
Why I need a clean rom : I tried FlyROM Manilla and Touch ROM WWE 4.02 full and vanilla but they are unstable. I had many white screens, phone shutting down in conversation, freezed many times.
I tried to flash with USPL and got the INVALID MODEL ID error (if I used a wrong rom please tell me what to chose from the list http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades ) ;sd card and sim were out, battery full
I tried to sd flash following these instructions http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing and got to the Update sd image but after presing the slider down the screen faded down. after 1/2 hour I pressed the power button and the old rom started
what was wrong ?
Now I'm using FlyROM manilla and i still want to flash a factory rom
Hi all,
I'm new to this. I am trying to back up my O2 Exec's ROMs before flashing a new ROM. I have superCID the phone and unlocked successfully but when trying to run a backup through mtty116.exe (typing in task 32) I get an error message saying-
USB>task 32
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SDetected one card
SD:ready for transfer OK
d.total_lba=1E2000
d.block_size=200
d.RCA=2
d.drv_type=40000000
d.busWidth=1
Total card size=3C400000
Read singal error D3
SD read fail!
Level = 0
Is this because I'm using a 2Gb SD card?
If so is there a way around this as this is only card I have. BTW I tried partitioning SD card to contain only a 128Mb partition but it didn't help.
I have been following the buzzdev.net tutorial at
http://buzzdev.net/viewtopic.php?f=40&t=33157&start=0&sid=1964ccffa3671d8cc24b1d1a71074929
Any comments or help will be greatly appreciated.
Regards,
64WT72
Sorry if my English is too bad, but i've got 1 problem when upgrading my p3300
My p3300 got spl 1.11.0000 that means i can easily upgrade my OS to wm6.5. I'm glad, but my ppc can't connect to pc via activesync so i decided to uprom in MicroSD card.
I learned in: http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
So i started upgrading, but i got some error. My ppc enter bootloader with this sign" Checking SD contents" end then it come back to the bootscreen( 3 lines of colors) . Now, i can't upgrade my Rom, can't enter OS. Please tell me what wrong with this progress. i think maybe my SD card too bad ( a chinese sd card), or my Rom too bad ( i tried 2 dif Rom).
Please someone help me. pls. Thanks first.