Changing covers - how easy is it? - Upgrading, Modifying and Unlocking

Hi folks,
I have an XDA which has been upgraded to 64MB which has a bunch of scratches on the covers.
I have a spare XDA (32MB) - can I "easily" swap the covers - or is it a nightmare?
Any help/pointers/comments appreciated...
Thanks,
Geoff

its faily easy just remove the 2 silver screws (big) 2 screws (small) in the back, firmley open it into 2 parts by a small screw driver (use the area in the buttom as a biggining point, get it opened, 4 other + screws for the LCD & the front case is out 2 + screws on the Motherboard & the back back is out, what you can swap though is the battery because its glued in the back part & the vibrator since you don't need to replace it, try opening the one with scratched first to know how does't work then i would be really easy to open the other one
PS just in case you screw up i am not responsible of it, don't try to swap LCD or stuff & don't try to open it using your hand since the LCD is attached to the front part & connected to the MB by a cable & the MB screwed to the back part, so very gently things will go well

Many thanks for the advice...
Appreciated

Related

M2000 Dismantling/Housing Replacement

I dropped my SPV M2000 a few weeks ago and it has sustained a few battle scars.
I bought a dummy model on eBay which is identical to the original and am planning to use it to give my phone a new housing. Problem is I have got half way through but am a bit nervous about the keyboard/screen as these have ribbon type connectors that need to be disconnected from the main board and then reconnected.
Has anybody attempted this? I've managed to replace the back part of the case successfully as it doesn't involve interferring with any connectors...
its pretty straight forward.
when you get the back cover off (six screws, 3 short and 3 long - two on the outside top and 4 under the battery) you'll see the rest button and the vibrate motor, just gently lever them out of theire respective recesses and leave them attaced to the system board.
Then with the phone held right way up, back facing you you'll see a ribbon cable just above where the vibrator motor was. Its taped down with yellow tape.
Gently peel the tape off (keep it safe to put back later)
then the black part of the connector that the ribbon slides into lifts up be very gentle and it will pop up. Once you've popped it up, the cable will come out easily.
Once you have that cable out, slide the keyboard down without turning the phone over, then put the phone on its side and separate the system board from the keyboard/screen by a couple of inches look at the back (as you see it it actually the front of course) of the sys board, you'll see two more ribbon cables that plug on to the sys board. Gently lift the edge of each connector and they'll pop off the board easliy.
take the sys board right out of the screen/keyboard, then undo the 4 remaining torx screws (you haveto have the keyboard fully extended to see the bottom screws) and the screen/keyboard can then be gently parted from the front screen surround.
assembly is the reverse of removal. The key is to extend the keyboard when you reassemble/reinstall the system board initially.
hope that helps!
cheers
-Griz
Griz,
Thanks - I will give it a try
Cian
Please include pictures maybe you can give a tutorial.
I've followed this and changed the screen surround on my M2000 without any problems.
The only thing not mentioned in the instructions is that there are 3 small screws that secure the system board to the housing that have to be removed before the system board can be separated away.
I bought a "dummy" M2000 from eBay and most of the casing from one of these can be swapped over. The only thing that can't is the centre section that contains the keyboard as the keyboard is embedded in this and can't be removed (the keyboard on the dummy ones isn't a working one).

Replacing the digitizer on the TP2

Hi,
Just purchased a TP2 with a cracked digitizer. I also have the replacement. I've done a bit of research, and it looks like a ton of steps. I'm pretty confident I can do it, so all I'm really looking for is some tips. Any surprises I might see that may not have been covered in this guide? This is what I have so far:
http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
how did you conclude that your digitizer is cracked?
The LCD is fine. It's the top layer of plastic that is cracked. I haven't received the phone yet, but I inspected it, and that's what I concluded. The person who sold it to me is including a replacement part, but I know I'm looking at a lengthy process to dismantle the device.
Do you have to take apart the entire phone just to change the digitizer? I thought you could just hook something underneath the corner and pry it out.
It seems like such a drag if you have to take the whole phone apart to change an exterior item.
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
have you managed to replace the digitizer only? if its such a mission why are so many people selling them on ebay? a scam maby lol?
i too am interested in your results, just now bought a cracked LCD htc touch pro 2 for $100, touching the screen works, except that the phone is stuck in head-set mode and can't seem to get out of it. also, i want to replace the lcd and use the phone myself. can you pls post your success/educational steps which you followed. also, where did you buy the replacement LCD? how much ? pls help.
ultramag69 said:
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
Click to expand...
Click to collapse
Totally agree here. From what I have read you dont want to mess around with trying to pry the current digitizer off and then reapply a new one on. It's a HUGE pain in the ass. Just purchase a replacement LCD screen/digitizer combo and i's apparently super easy to swap out.
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Redman0570 said:
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Click to expand...
Click to collapse
Hi, can u post how you go with this e.g. is it easy enough to seperate the lcd and touchscreen. Maby a few pics as well if you can.
Cheers
It can be done but it requires ALOT of patience. Take it slowly and try not to leaver against the LCD in anyway. If you do break the screen when replacing it a replacement isn't expensive.
I replaced the digitizer twice. Taking the phone apart and assembling it back is difficult only when you do it for the first time. Once you know what's going on it just takes some time and precision. The REALLY tough part when replacing JUST the digitizer is putting the lcd and digitizer together without any dust or fingerprints in between. I ended up with dusting and vacuuming the room, putting some super-clean brand new plastic bags around the workplace and putting the cold shower on. Then using super-clean glass polishing microfibre cloth and anti-static glass cleaning liquid under really good lamp I managed to get both parts 100% clean and put them back together. Don't forget latex gloves (the ones that leave no marks) - fingerprints are hundred times worse than dust to get rid of. I have no idea how long did it really take but when I finished my back hurt like hell and water was dripping from the ceiling
Separating lcd and digitizer is not too hard. It was easiest when it was still attached to the bezel. I just pried it out applying easy, firm pressure and taking my time. Try not to damage the sticky layer on the edges or get it excessively dirty - it'll make your life easier later.
I hope it goes easier for you. Gud luck!
EDIT: Make sure that lcd is positioned 100% correctly (there is 1 or 2mm space to move it around). It is a very unpleasant surprise to put the phone back together just to find out that some top or bottom pixel lines are permanently invisible (The Voice of True Experience speaks here:/). And generally - keep the place around you tidy - maybe some containers for screws, parts, tools and that sort of stuff. I am not naturally anal enough to start from this point but found out in the process that this sort of job gets extremely frustrating and exhausting when you get confused, start losing parts etc.
It is major hurt! The TP2 is really not user serviceable! Anyway after reading all instructions I still screwed it up. I should have sent it in to HTC. I would not recommend changing the digitizer on your own.
Everything went well until it came to removing the LCD & replacing the digitizer. I cut the speaker cable, and the LCD just came apart. Luckily I have another LCD, looking for a speaker cable now.
has anyone found any places that sell the lcd and digitizer together for the T-Mobile TP2?
Thanks to these instructions I was able to replace the broken digitizer (glass) on my TP2. Unfortunately the Russian instructions stop short of replacing the glass.
Tools required: T5 torx mini screwdriver, letter opener, mini philips, a mini straight screwdriver and I found a very mini (1mm ) straight screwdriver handy for getthing the keyboard and screen back loose. The letter openner and two straight screwdrivers are only for prying
Here is what I did from the last spot on the Russian instructions: (yes you have to do every step)
Note: Be very careful removing the ribbon taped to the back of the LCD. You have to pry the speaker out ot the case up at the top; don't attempt to remove it by pulling on the ribbon. Once the speaker is loose (it's attached to the riboon, you are ok to remove it.
1. Take a small straight screwdriver and pry all around the LCD (metal back with handwriting on it in the last photo.) There are plastic tabs all around it centering it. You can pry gently against them. The LCD is only adhered with a small gasket around the edge of the glass. It is not glued to the screen as was posted by someone else. It comes out fairly easily.
2. Remove the black tape holding down the ribbon connected to the digitizer. I wasn't able to save the tape but not a big deal. Below the tape is one of three screws holding the buttons on. Remove those three screws.
3. Now you should be able to remove the digitizer. Go slow starting at the bottom. It is glued all around at heavily glued at the top. I had the pry the top away with small flat screwdriver and a letter opener. Go slowly and eventually it will release. At the top of the glass is the speaker for your ear. It will likely come off with the glass. Remove it and return it to the now empty case centering it in top.
4. Using gloves to prevent prints remove the protective film form your new digitizer. There is a lot of static generated when you do this so keep it away from everything for a minute while it neutralizes. Then place the digitizer in from the top, feed the ribbon through the slot and press the plastic all the way around.
5. Replace the buttons and the screws that retain them.
6. Replace the LCD; you can't screw it up the plastic tabs center the LCD. Just make sure the ribbon is at the bottom.
7. Reverse the instructions in the Russian link at the beginning of the post.
All told it took one hour the first time. I got it all together and then screen didn't light it. I had trouble reconnecting the screen ribbon during assembly so I figured the problem was there. I took the phone apart (to the end of the Russian instructions) and reinserted the screen ribbon into the connecter and then reassembled the phone. It took 10 min to disassemble and reassemble the phone the second time although I didn't have to take apart the screen.
So that's it. It cost me $22.00 for a new digitizer and $10.00 shipping, which is a lot better than a new phone if you don't have insurance and the phone looks like new. If you look very hard you can make out one tiny speck of dust under the glass but it's barely visible; much better than looking at the large V shaped crack I had before.
Hello!
I ordered (and received) a screen AND a digitizer. But there's a thin scotch tape that make the screen+digitizer (in one piece) get stick to the phone. OK, I teared it off.
But, how can I replace this scotch tape??? Much less of 1 mm thick, it seems to be made of foam...
Anyone can help me???????????
Please....
Coucou !
Is there anybody out there?
(Pink Floyd, The Wall, 1979 )
I was sent a Digitizer from Ebay (without LCD). Just for everyone elses benefit, there is no way you can remove the digitizer from the LCD Screen. It's glued down. Maybe it wasn't the case with the older ones, but mine can not be separated, no way!
Taking the phone apart is not too hard, the video instructions are pretty good, but seriously, forget trying to replace the digitizer only.
Here is the video:
http://www.youtube.com/watch?v=MrTRPTmoxpw&feature=player_embedded
Cheers, Mal.
If it has the same construction as the HD2, you can put the LCD + digitizer in the oven for 5 minutes at 50 degrees celcius. This was shown in instructions by HTC. Then you can seperate them.
Maybe, but my LCD was glued across the whole screen not just the edges. I'd suggest only buying the Digitizer/LCD combo if you want to do this yourself. If you buy both (as a single piece) the job would be pretty easy.

Replacing the lens cover of the camera

The little square plastic cover of my camera lens has got a ding in it. Has anyone else replaced one of these and if so how difficult is it. Also where could I source one from? Thanks in advance.
Sent from my GT-I9100 using xda premium
I replaced the whole back part at a samsung official technical shop because of a scratch but if it's not a scratch, just open it and clean it with pressurised air (but it's a bit risky because you might loose warranty)
here's a guide i googled ... : http://www.youtube.com/watch?v=65pvAINg2ME&feature=related
Hi Nik
Thanks for the reply......
Are you saying it was done by someone else? How much did they charge you? Warranty isn't a consideration but obtaining the part may be difficult.
Sent from my Xoom using XDA Premium HD app
I bought the part from ebay for about 12 CAD shipped and replaced it myself. Quick and easy job, took about 10 minutes altogether.
Great video, it actually looks fairly easy to replace the back cover...thanks man that's a big help
Sent from my Xoom using XDA Premium HD app
Ahhh we must have posted at the same time . Thanks Akusokuzan....out of curiosity, what happened to yours?
Sent from my Xoom using XDA Premium HD app
Hey there,
Are you saying it was done by someone else? How much did they charge you? Warranty isn't a consideration but obtaining the part may be difficult.
Click to expand...
Click to collapse
Yes it was done by samsung's affiliated repair shop in France, it was because le little plastic was scratched very hard with sand (beach etc) so all photos i would take were blured with a white fog
I'm not a huge fan of opening anything except my computer but i'm sure it could be done easily since it's just opening and cleaning (or whatever, i have not really understood what happened to you camera )
to find the part, i found someone on xda that had provided a link to the original parts of the samsung galaxy S2 for like 10 bucks which was very difficult to find because as a french i wasn't knowing the exact word for the "backplate or whatever it is"
now i know it, just google "galaxy S2 original housing" and you'll find plenty results like this one here (assuming you have to change the whole back cover )
and last things it cost me 25€ for the back only with no extra battery cover which is a bit overpriced :V
I actually just wanted to change the mid part to white to have the contrasting black/white lol. just give my phone a bit more character. The hardest part about replacing the housing though was taking the speaker out of the old one and putting it in the new one (where the hump is).
Fixed
Wow...that was easier than I expected. The kit is the same quality as the original as far as I can tell. The case cost me about $30on ebay.
Following the video I'd say that most people could probably repair their phones without too much trouble.
Thanks for your help
Have anybody actually tried to change only the camera lens cover?
I can find the part here on ebay, but I can't seem to find any instruntion or teardown on how to exchange it.
Is it glued on?
Aavar
aavar said:
Have anybody actually tried to change only the camera lens cover?
I can find the part here on ebay, but I can't seem to find any instruntion or teardown on how to exchange it.
Is it glued on?
Aavar
Click to expand...
Click to collapse
Hey Aavar, have you finally replaced the camera lens cover? The rear ones. Have you found a guide for this?
Regards.
skyline_22 said:
Hey Aavar, have you finally replaced the camera lens cover? The rear ones. Have you found a guide for this?
Regards.
Click to expand...
Click to collapse
I've done this, and it's relatively simple.
1. Remove battery cover and battery (you can remove micro sd and sim if you like).
2. Remove the 7 screws with a precision screwdriver, do not lose.
3. Carefully pry back half of phone from front half (I just used my thumb nails), be careful not to lose volume & power buttons.
4. The lens cover has three tabs that enter from the outside of the phone, and fold over on the inside to prevent it moving. Fold these out so that they are vertical (in doing so mine broke, but this does not matter as we are installing a new lens cover).
5. Once tabs are vertical, push lens cover out (this may take some persuasion).
6. Install new lens cover, fold tabs back and put phone back together.
Let me know if you need photos or further details.
chimpdaddy69 said:
I've done this, and it's relatively simple.
1. Remove battery cover and battery (you can remove micro sd and sim if you like).
2. Remove the 7 screws with a precision screwdriver, do not lose.
3. Carefully pry back half of phone from front half (I just used my thumb nails), be careful not to lose volume & power buttons.
4. The lens cover has three tabs that enter from the outside of the phone, and fold over on the inside to prevent it moving. Fold these out so that they are vertical (in doing so mine broke, but this does not matter as we are installing a new lens cover).
5. Once tabs are vertical, push lens cover out (this may take some persuasion).
6. Install new lens cover, fold tabs back and put phone back together.
Let me know if you need photos or further details.
Click to expand...
Click to collapse
Can you give me a link of the piece?
Joost
Thanks for information.
I had the same issue

Replace Chrome trim on SGS2?

I'm trying to find a source on whether I can replace the trim know my phone since it's been dinged from the previous owner as well as myself.
I've found some the link to the replacement screen thread but it doesn't say if the lcd is part of the top or how to get it out? I've seen some oem housings online but not sure if I can remove my lcd which is fine and put it in the newer housing?
Is there glue or adhesive that holds it in?
Thanks for any help.
Sent from my GT-I9100 using xda app-developers app
You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.
supermult said:
You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.
Click to expand...
Click to collapse
Sorry - but I think we have a misunderstanding. I'm talking about the chrome trim around the entire LCD not the camera.
oh.. honestly i don´t think that the part you described is chrome. Atleast not on my GSII
and the thing i posted is the shiny ring around the headphone plug.
OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.
Nyssa1104 said:
OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.
Click to expand...
Click to collapse
Thanks - that's what I wanted to hear. So it's more effort than I'd like to spend on it. Looks like I'll just move the phone to try something else.

SM-P600 series LCD+Digitizer replacement

SM-P600 series cracked screen repair.
I have a badly cracked screen on my SM-P600 and have ordered the complete LCD + digitizer to do the repair - having watched how difficult is was to clean a phone with LCD glued to the screen - and it also seems that there is nobody willing to take on the job in the UK.
The screen and all the internals extract from the front screen side of the unit leaving a "carapace" behind.
Bought LCD here -> http://www.ebay.co.uk/itm/LCD-Screen...item3ce14e2f51
Tools used :- Old credit cards cut to suit (tools had not arrived) and watchmakers cross point screwdriver. Hair-dryer. Stanley knife (Utility knife)
I decided not to video my repair as it would have taken days - being in my 70s and not too clever with the eyes, meaning I have to keep changing spectacles for everything and I have a dreadful habit of removing an item or using a tool, putting it down and spending the next few minutes looking for it - you've guessed it - changing specs!
There is a perfectly good strip down on Utube here :-
https://www.youtube.com/watch?v=zOzrRu8PB2Y many thanks to Gorepair.de for the video - and that's the easy part.
After removing all the gubbins you are left with the LCD + digitizer attached to a grey frame by means of thin double sided sticky tape. I heated the peripheral of the screen with the wife's hair dryer and very carefully removed the cracked screen. By doing this I was able to re-use the tape on the new screen after carefully examining it for any glass splinters etc.. I also placed greenhouse tape - thicker & wider than Sellotape - over the screen before dismantling so that I was not showered with glass splinters. Another tip is a piece of sellotape over the power & volume buttons to keep them in place - they may be held in by other means but it's belt & braces, no harm there.
Before replacing the screen in the frame remember to replace the HOME button as I found out the tape is indeed very sticky and it was a bugger separating screen from frame to insert the button which I had, of course, forgotten to put back in! Should have Sellotaped it in new screen immediately on removal from the damaged one! There is also a short golden coloured multi tape that needs to be fed though the frame.
Now it is just a matter of reversing the strip down procedure and Fred is your Aunt Fanny's best friend!
The unit did work afterward despite my repair. It took me about three & an half hours including changing specs and lookin for misplaced items, so I'm sure less than two hours for a good sighted person that is "compus mentis" :¬)
It is not as daunting as it may first seem!

Categories

Resources