Hi,
I have a problem with a Bluetooth GPS receiver (COPILOT) and pairing it with the XDA II.Why does it always asks me for a device PIN.I haven't got one.Why do I need one and why can I not do it without a DEvcie PIN ?
I am ROM 1.6 and Radio 1.1
Help would very much appreciated.
Heiko
To prevent people from making unauthorized use of the unit! If you haven't got the pin then there's probably something fishy about the way you got it ........
Do you have a manual? it should be in there.
Nothing fishy about it.Bought it from expansys.Does every device need a PIN then.Got Software activation code and all the boxes and manual.
Are not explaining pairing in the manual at all.Should just work according to the Manual.
Heiko
0183
All you needed to do was search the forum for Copilot.
I searched for Bluetooth and GPS,but Copilot did not come to mind.
I think I am a bit fed up in having so many problems.
EXPANSYS seem to have sent me an incomplete package.Only half the Vent mount kit and no instruction booklet for GPS.
Thanks very much.You made my day!
I am very grateful to you for that info.
Hope it will sort my problem.
Heiko
I am step furher .I got the two paired now.
It seems that I have no proper manual for the GPS receiver would anybody know which Com Port I need to set it to and what speed ?I get a green tick for GPS Comp Port Opened and when I choose Setup GPS,
Automatic seems not to detect.I get error message "Automatic GPS connection failed.Verify that your receiver is connected.".
Any ideas?
Thanks Heiko
Try com 5, assuming you answered yes to the question about serial device when bonding the gps.
I think for future reference here is my painful configuration experience of COPILOT Version 5 with a Copilot Bluetooth GPS receiver and XDA II.
1.Check that the Quickstart Package is complete:
-GPS receiver User Guide,Ventmount Kit with attachment for PDA,Bluetooth PIN code for GPS receiver.
- User/Installation Guide
- CDs and 128Mbyte SD card
2.Install the Software from the SD Card according to the User Guide
3.Check the Version number and note it down.Go to the Technical Support section of the Copilot Website and see whether there are any Patches available.
3.Deinstall the software from your device and install the patched software which you need to copy onto your SD card.
4.Install the software.
3.Check that you have bonded your Bluetooth GPS receiver with the XDA II and enable Comport 4Inbound and 5 Outbound.(ROM Version 1.60)
5.Use Code 0183 as the Bluetooth device PIN code
6.Go into Copilot software and everything should work as it did for me if you haven't lost the will to live by this time !
7.read this first : Buy a SatNav system with your car and haggle with the salesman like mad (its quicker).
Hope this helps everyone else as people helped me here.
Thanks
Heiko
Thank you, Thank you, Thank you for the code
I was just about to give up, but the 0183 code worked like a charm. I have the new PPC6700 with WM5 and all of a sudden it wants the code. Previous versions never needed it. You just saved me $150.
Thanks again
I have purchased a Polstar Gmouse GPS with XDA serial and power cable. The GPS seems to be powered up but the software on the XDa says it does not recognise a connection. All possible com port settings and speeds have been tried. My first question is Has any one connected a gps device through an XDa o2 serial / sync connector succesfully ?
My second question are there any settings in the windows software to control the serial connection to plug in devices ?
I am about to return the GPS products for a refund but I thought I should ask for help first.
Cheers
John
Mandurang South
Victoria
Go to settings/connections, make sure that the recive incoming beams box is UNCHECKED. If you have the driver for external keyboard loaded make sure the driver is disabled. In your gps software choose nmea 4800 and Com 1. If you have done all that then I would suspect the cable or the gps. I have used many different serial gps devices on xda and xda 2 and it works 100 percent.
Fan bloody tastic
Well I was going to post a similar question as the OP but with a little browsing, it looks like I may have found my answer. Will go & experiment, if it fails.....I'll be back!!! Watch this space! 8)
Cannot open com1 port does not exist
I have had a major problems connecting my GPS recently and not thinking!!! I had recently bought a infrared keyboard. You're instructions worked perfectly. You have just solved my problem. Many Thanks
Kevin :wink:
can some one here please help me this is driving me mad for days now i have been looking thro the forums at some of the posts how to set up tomtom 5 and how to setup the gps bluetooth receiver i have followed all instructions how to but iam not getting any where tomtom is installed ok the gps control panel is installed but i cant seem to get any blue tooth com ports to show up in tomtom apart from
qct data interface
ril on com6
com7
serial cable on com1
Ir on com3
if i rember when i had it installed on my xda2i when i went to tomtom and
bluetooth other then com ports i could pick from tow bluetooth coms 5 & 6
this really is getting to me now i do believe it possible to do it there guys selling the info on ebay with pictures of it running on the xda exec but i just cant seem to do it
please i would be so greatfull for any help i only got the phone last week i like it
sorry i think i had posted this in the wrong place iam not used to forums
thanks any way i have sorted it out now my xda exec is working really well with my tomtom and gps bt-77 receiver all is good
Hi all,
This forum being the greatest about HTC, I think you guys will have the answer :
I would like to use my TyTN to connect to the console of a router (using serial connection) :
1. Does anyone know where I could find a miniUSB-DB9 adapter ?
2. Will there be a driver for serial port, or is it natively managed with COM ?
Such cables exist but for PC, but not miniUSB and with a Windows driver, no info about the same thing for PocketPC.
Anyone knows ?
Thanks
zEar - HTC TyTN
Re
----
DELETED Message where I thought I found it..
Understood the problem..
Hi all,
AFAI understood I cannot find a solution due to the lack of USB Host support in the TyTN. I still wonder if the port can be used in direct low level serial mode as you see in bootloader. Could WinMobile use it ?
Another way would be to have a device that would be usb host, putting the phone into slave mode, but maybe I dream...
Thanks for any reply..
there is a bluetooth to serial adaptor which has been reported to work with the tytn.
COM1
Hi,
After much googleing there's still hope. Windows Mobile presents a COM port : 'COM1 via cable' and in the specs of the TyTN there is RS232 communication.
I still cannot figure out if the miniUSB connector pins could be simply mapped to the corresponding RS232 signals. Probably not
Anyway I flashed the XDA-Live wm6 ROM and it's great ! the battery seem to last longer (still 70% after 2 days!)
Thanks to the xda-dev community
Dear All,
I would like to share my experience in this TMC project.
Recently I bought a Chinese GPS 100 unit to connect to my JVC KD AVX40
This has an av out in 320x240 and JVC has an AV in.
You can control the unit via touchpad.
It works correctly to my unit so I decided to get a TMC for this product.
This unit has One USB port which is in Host mode.
So Put a normal USB hub on it and it worked well with Pendrive and External Mouse
Next step, I got a FTDI USB to Rs232 device.
It has FTDI 232BM chip for UART connection it's very important to use chip like this , because of the windows ce driver
I've opened it and I removed chip called SP213EHCA.
In every RS232 there are 2 chips on the board. One is for USB to UART , and the second is for Uart To Rs232.
Because the every TMC receiver uses TTL communication which is working on 3.3v I need to "convert" the unit to USB to UART TTL only.
Obviously you can build a small circuit for this communication, but for myself it was easier to use this solution.
After I removed the Rs232 chip.
Datasheet Page 5 for picture of the pin outs.
You can download it from the FTDI website
The Tmc Receiver pin out is :
Pin definition:
Pin1 Vcc: 5V +- 10%
Pin2 TX: 3.3V TTL level, TMC data output.
Pin3 RX: 3.3V TTL level, receive commands.
Pin4 GND <-- It's not ground It's 5V !!!
Pin5 GND (for mini-USB only)
I soldered a mini USB mother type connector to the chip legs:
PIN2 goes to chip leg 24
PIN3 goes to chip leg 25
PIN5 goes to chip leg 17
So after this I connected the Royaltek TMC unit to my "hacked Rs232" board.
I put the "hacked rs232" to hub and I used a USB mini usb cable for power the tmc unit, so I connect the cable to hub and after that to the tmc.
After this I used this driver for windows ce 5.0
You can download it from the ftdi web site
I have to use mortscript which copy a self made reg file to the registry and copy the ftdi dll to /windows/ folder
Reg:
REGEDIT4
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\1027_24577]
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\1027_24577\Default]
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\1027_24577\Default\Default]
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\1027_24577\Default\Default\FTDI_DEVICE]
"DLL"="ftdi_ser"
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\Default\Default\255]
[HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients\Default\Default\255\FTDI_DEVICE]
"DLL"="ftdi_ser"
[HKEY_LOCAL_MACHINE\Drivers\USB\ClientDrivers\FTDI_DEVICE]
"Index"=dword:00000001
"InitialIndex"=dword:00000001 <--- This is for which com port to use 1...9
"Dll"="ftdi_ser"
"Prefix"="COM"
"Version"="1.0.2.11"
"ActiveSyncSetting"=dword:0003e880
"LatencyTimer"=dword:00000010
"DeviceArrayIndex"=dword:00000000
This reg file is directly uses COM PORT 1 (It was free in my device )
After this I created a very small circuit which holds the usb power for 20sec
parallely my reg and driver is installing in this time.
When I reached 20sec My Hive based Windows Registry will recognize the FTDI device and there are no pop up meassegas appear ....
IGO recognized the TMC device hardware
The reason I write this how to , because I read so many forums ,and web pages to find a solution for this , but i didn't find anything.
GNS is providing a TMC receiver for CAR PC but with a prolific based USB to UART chip, and the ARM based cpu is not understanding the driver
Ough I forget the tmc receiver what used:
Royaltek RTA-3000
Have a nince day I hope that I could help to someone
guika said:
Dear All,
Snip, snip
Have a nince day I hope that I could help to someone
Click to expand...
Click to collapse
I got the same JVC stereo, how can I unlock for multizone DVD? Thank!
If i understand it correctly that you mean, you want to unlock the dvd region limitation.
I didn't unlocked it, but the main problem, that the unlock lock status is came from the dvd FW, which is not possible to reach it, via this unit. I searched for the web, and JVC also, for some FW update. There isn't any. So from my side i say it's not possible in easy way.
I have tested this solution and since half year aho its working fine under -20 to +50 so it is a solution.
Sent from my GT-I9000 using XDA App
Compatibility
Also tested with FT2232H
This soultion is working , only bug that because of the dual uart the windows device pop up a notification for the second uart driver.
Also working.
Not working with Moxa chip.
Not working with Prolific PL-2303. ( Because the driver for the chip is not going to get open com port in wince 5 :S )
It seems that the only solution is the FTDI chip.
I've made a test with bluepanter and Wayteq and a very old Blaupunkt.
Solution is worked when I changed the usb mode to Host in wince.
It's seems for the blepanter and the wayteq it make not so much sense bacuse you could buy their original accessories.
For the blaupunkt is okay.
Also this could be okay for the 1-2 din chinese gps. Needs to be tested.
Reception improving
I had issue with the tmc reception.
So the solution is make a fm Y cable, and share the outdoor antenna to the head unit and to the tmc receiver.
After the installation, I realised that the reception was not so good, because I miss calculated with the phantom power to my roof antenna, after the phantom power installation everything went fine.
I got reception where I never had it before. TMC news downloading time improved as well.
Take care with the phantom power because it could kill the TMC receiver, use only one way adapter !
hi,
many many thanks for you thread...i had some questions...
i have bought an Dynavin DVN-MC2000 and this unit is without TMC but it have an GPS-In Mother-Usb cable...i think this goes directly to the wince5.0 system.
Where did you buy your RT-3000 and do you have the complete name of the FTDI Modul?!
Maybe we can develop a solution together i could make fotos from my open DVN-MC2000 if it helps
Maybe a ohoto would be great.
I bought the tmc unit in hungary in an avarage shop.
About ftdi i had one in my work desk. But it doesnt matter the meaing is it should any type which is supporting from the wince ftdi driver side. See ftdi web.
Sent from my GT-I9000
Hello all!!
I've been reading the post and I have to congratulate you, very interesting!
If you do not mind I'll use this thread because I want to ask you a question, I haven´t found any response in any expert forum.
I have a problem with my car radio. It is a chenese radio with GPS and TMC integrated.
From the beginning the TMC worked correctly but It had problems with the GPS. It didn´t work properly (may be the driver was wrong or it was bad installed on the WIN CE5). The provider din´t give me a solution and I found a forum in France. There someone sent me an European WIN CE 5 ROM with the GPS installed a working properly. The problem is that this guy didnt have any ROM with the TMC driver integrated and now I dont have it installed.
My actual state is: WIN CE + GPS HW (installed and working) + TMC HW (not insalled)
My question is:
How could I install the TMC in my radio WIN CE5? The HW exists but my WIN CE 5 does not have the drivers and of course the IGO can not find it.
Thank you very much!
pd: sorry about my english!!!
elmike1980 said:
Hello all!!
I've been reading the post and I have to congratulate you, very interesting!
If you do not mind I'll use this thread because I want to ask you a question, I haven´t found any response in any expert forum.
I have a problem with my car radio. It is a chenese radio with GPS and TMC integrated.
From the beginning the TMC worked correctly but It had problems with the GPS. It didn´t work properly (may be the driver was wrong or it was bad installed on the WIN CE5). The provider din´t give me a solution and I found a forum in France. There someone sent me an European WIN CE 5 ROM with the GPS installed a working properly. The problem is that this guy didnt have any ROM with the TMC driver integrated and now I dont have it installed.
My actual state is: WIN CE + GPS HW (installed and working) + TMC HW (not insalled)
My question is:
How could I install the TMC in my radio WIN CE5? The HW exists but my WIN CE 5 does not have the drivers and of course the IGO can not find it.
Thank you very much!
pd: sorry about my english!!!
Click to expand...
Click to collapse
From the first i need to know what kind of tmc chip do you have. Royaltek/GNS and after that we can get closer to the problem. Qhit the upper sokution you can put in the driver if we will figure out the chip manufacturel.
Sent from my GT-I9000
I am sure that the integrated chip is GNS tipe.
The only thing that can hapen if we install a wrong driver is that it would not work, wouldnt it?
But the other things would work good...
thank you!
elmike1980 said:
I am sure that the integrated chip is GNS tipe.
The only thing that can hapen if we install a wrong driver is that it would not work, wouldnt it?
But the other things would work good...
thank you!
Click to expand...
Click to collapse
Generally yes.
But first. You will need to do some test. I will post it later. Because right now in this days i have a lot to do. I wont forget your problem so i will post it here what to check first to start your problem solving....
Sent from my GT-I9000
thank you very much!
I will wait for your answer.
regards.
please dont forget me!!
bye!
Dony worry i wont
Sent from my GT-I9000 using XDA App
Hello Guika,
Where did you get your Chinease GPS 100? can you send me the link?
Thanks,
cjean said:
Hello Guika,
Where did you get your Chinease GPS 100? can you send me the link?
Thanks,
Click to expand...
Click to collapse
http://www.car-audio.hu/?base=items&filter=cat&type=item&catid=0&cid=141&id=714
Sent from my GT-I9000
elmike1980 said:
thank you very much!
I will wait for your answer.
regards.
Click to expand...
Click to collapse
I found something maybe from your IGO8 folder is missing one file called gpstmc.dll
Check this forum
http://www.mobilepassion.org/viewtopic.php?t=2355
I will check it.
Anyway I think that I need the driver for TMC receiver. I have the HW but it is not installed. Do you know were could I find TMC drivers for Win CE 5? with them the problem would be solved-install and the IGO would take it automatically (I had it installed the first time, but the GPS didnt work).