Hey guys,
Running ILWT CM7. Flashed about two weeks ago. My phone has been working fine except for the past few days where it's been constantly freezing, requiring a battery-out and turn on, and rebooting on it's own.
Last time it froze, I removed the battery and turned back on, and it got to the "htc" logo and froze. After ~25minutes, I took the battery out and tried again.
Phone seems completely dead, won't respond to power on, volume down and power on, no lights come on when charger cable is plugged in. When USB cable is plugged in and no buttons or anything on the phone is pressed, my laptop attempts to install drivers.
Tried leaving battery out for 30minutes and trying again, but no luck.
Any suggestions?
Cheers!
Stuck in RUU mode?
Kaph said:
Hey guys,
...
Last time it froze, I removed the battery and turned back on, and it got to the "htc" logo and froze. ...
Phone seems completely dead ... When USB cable is plugged in and no buttons or anything on the phone is pressed, my laptop attempts to install drivers.
... Any suggestions?
Cheers!
Click to expand...
Click to collapse
Looks like your phone is stuck in RUU mode.
In RUU mode you see the silver "HTC" logo as long as your phone is connected to your computer with an USB data cable. No charging lights will show in this mode.
You can use the following command to boot your phone to Android:
Code:
fastboot oem boot
When that does not work, because your partition table or system partition might be corrupted, then you would have to use the correct RUU (Rom Update Utility) for your phone to get it back to a working state.
When you have a bricked internal memory chip (emmc) than nothing will work properly to restore your phone to normal working conditions.
In the case you have an engineering HBOOT you could boot a ROM from SD card, but that is a far shot.
Best regards,
Catherall
catherall said:
Looks like your phone is stuck in RUU mode.
In RUU mode you see the silver "HTC" logo as long as your phone is connected to your computer with an USB data cable. No charging lights will show in this mode.
You can use the following command to boot your phone to Android:
Code:
fastboot oem boot
When that does not work, because your partition table or system partition might be corrupted, then you would have to use the correct RUU (Rom Update Utility) for your phone to get it back to a working state.
When you have a bricked internal memory chip (emmc) than nothing will work properly to restore your phone to normal working conditions.
In the case you have an engineering HBOOT you could boot a ROM from SD card, but that is a far shot.
Best regards,
Catherall
Click to expand...
Click to collapse
Thanks for the help
When plugged in with the USB cable -> computer, I still get no response from the phone itself. Screen doesn't turn on, still seems dead. My laptop still says "Installing device driver software" to no avail, and phone is still dead. No lights, screen is off, nada. As though it was powered-off.
ADB Devices lists nothing, and fastboot oem boot hangs on <waiting for device>.
Am I out of luck? I could send the phone off for repair, but as I'm rooted I think warranty is void.
Remarks
Kaph said:
Thanks for the help
My laptop still says "Installing device driver software" to no avail, and phone is still dead
ADB Devices lists nothing, and fastboot oem boot hangs on <waiting for device>.
Am I out of luck? I could send the phone off for repair, but as I'm rooted I think warranty is void.
Click to expand...
Click to collapse
Windows seems to need a driver installation for using fastboot. Did you try to automaticall install device driver software? Have you installed HTC sync on your Windows computer?
When your device does not respond at all, and even refuses to connect in fastboot, then nobody can tell that you have been rooted.
Best regards,
Catherall
Sounds like your EMMC is fried, as of now I don't think there's a solution other than sending it back. Many say HTC accept and fix it even though it is s-off
Sent from my HTC Vision using XDA
did you get this worked out? i had a similar problem, ended up booting into fastboot by holding the trackpad and the power button, then just selected reboot and my phone powered on like nothing had happened, i was running the same rom.
Hey, did you alreasy tourned your phone to the fastboot mode?
Or does your device still have a black screen during boot?
I rooted this phone and when I was done trying S-OFF, phone would not respond to anything. It would only blink the orange notification light when I pressed Power and Vol+, or it would stay steady green with both Vol keys and Power. But the phone screen would never turn on. So after trying for hours to figure it out. I finally took the battery off, plugged the phone held pressed the power button and then put the battery in place the phone finally turned on and it worked. I turned the phone off again and it was doing the same issue. So I did the same step but this time with power and vol- to get in the bootloader and changed the hboot version to Desire Z. After that phone works perfectly, turns on and off with out any issues.
I did have to try the trick a couple of times idk why but it would work once in a while not everytime i tried it. Hope this helps anyone who also ends up with a similar issue.
Hi.
I have a Xiaomi mi5s 64/3 GB in an endless bootloop. Here are the details:
The phone is:
rooted
bootloader unlocked
developer mode enabled
internal storage *not* encrypted
no MIUI account activated
USB debugging on
running the last EU MIUI 9.x development version (don't remember the exact version) with Android 7.0
has TWRP 3.2.1.0 and supersu 2.82
no password is set for unlocking the screen etc.
For some unknown reason the phone suddenly rebooted yesterday and got into an infinite bootloop cycle. I haven't changed any roms recently or done any such flashing. My google play automatic updates were disabled, but a few days ago I manually updated all the apps.
The only odd thing that happened prior to this bootloop, was that when shooting some photos with the google camera mod (same one I've been using for the past few weeks), 2 images were saved as corrupt unreadable files. But that happened a few hours before the bootloop suddenly started.
The current status is:
1. I cannot turn the power off (tried holding the power button, or power button + vol up and down for a very long time --> nothing).
2. I cannot enter recovery mode using vol up + power.
3. I cannot enter EDL using all 3 buttons.
4. If I hold volume down, it enters fastboot but automatically exits from it within 4 seconds (ADB and miflash cannot detect the device in this short period of time). holding the volume down button for a long time has a repating enter-exit-after-4-seconds from the fastboot graphics.
I waited until the battery was completely dead, than started charging it and the status described above was unchanged.
QUESTION 1 - restoring the internal data is my number one priority - does it seem possible here?
To be exact: I want the DCIM folder with the photos+ videos. What should I try now?
QUESTION 2 - I ordered an EDL cable, but am unsure if it supported for my MIUI version. if the EDL cable works, can I force the phone to enter recovery mode from within EDL?
If so - I guess I can copy the internal data to an external USB OTG flash drive I have (that works well with the phone).
If my data is restored, I will then move onto trying to reflash the phone, but at this point this is the least of my worries...
Thanks all.
Anyone?
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
bedson87 said:
Maybe it's a problem with the button? I would disassembly the phone and check the hardware.
Click to expand...
Click to collapse
I don't know - the buttons don't seem like they are stuck in any way. When I push them, they click back out as usual.
Update - I created an EDL flash cable by stripping the cable gently, exposing the green and black wires, and looping them together - connecting this cable to the phone didn't help either.
Maybe I need to wait for the battery to die so the phone will turn off, connect this cable to the phone, keep the power button pressed while I connect it to the usb port in my PC... what do you think?
I have the same problem with mi 5s which started after update. Don't know what to do.
Took the phone to a local lab - it was all due to a faulty power button module.
So Here are the steps
1. My bootloader got unlocked.
2. I Installed factory preloader and lk images.
3. Rebooted to Fasboot and flashed TWRP 3.3.1-0924 by wzsx150 (the only Android 9 recovery that didn't get removed immediately after flashing and rebooting for 1st time to get to recovery).
4. Formatted Data, Closed AVB 2.0 and Signed TWRP.
5. Rebooted to Fastboot and flashed stock EEA Android 9 (11.0.3.0) from Global (11.0.6.0) and reflashed factory preloader and lk.
6. Rebooted to recovery, Formatted Data, Closed AVB 2.0 and Signed TWRP.
7. Using ADB sideload from Twrp Installed EEA Android 10 (11.0.2.0).
8. Rebooted into fastboot Installed Updated TWRP-3.3.1-1210 (by wzsx150).
9. Rebooted into fastboot and flashed misc.bin from same zip (according to bat file inside it should get flashed after recovery but I forgot.)
10. BRICKED. Booted to Redmi logo for 3 seconds and rebooted infinitely.
This type of brick in 4pda.ru according to google translate can be mitigated by letting battery drain and then enter DA download mode using SP Flash Tool.
I've Used the tool several time so I thought Okay no big deal.
So This is what I tried:
11. Pressed download button
12. Connected USB Cable to phone.
13. Device pauses a second (Probably for SP Flash Tool to respond) then doesn't enter DA (Unlike previous times) and screen brighten for a second or two but then turns off and repeats this process forever.
I've been using Drivers provided by Microsoft Update Catalogue but tried all the drivers on 'MTK Usb Driver v1.0.8' and 'Mediatek_Driver_Auto_Installer_1.1352.00' after disabling Driver Signature Enforcement. but even though drivers are installed they don't get loaded and after force installing them in add legacy drivers they are their but have yellow triangles and their Location lists as 'Unknown' and status as 'This device cannot start. (Code 10)'. Tried Removing them after adding them as a site suggested but that didn't work either.
I learned the hard way to never mismatch partitions with this phone. I thought having the factory preloader and lk1/2 would protect me but no.
When you say brick, do you mean you have a completely black screen with only the notification LED turning on when you plug it in?
Grab a bootable Linux image and use that on a USB stick to eliminate the driver issue you're having. Interface is identical
wang1chung said:
I learned the hard way to never mismatch partitions with this phone. I thought having the factory preloader and lk1/2 would protect me but no.
When you say brick, do you mean you have a completely black screen with only the notification LED turning on when you plug it in?
Grab a bootable Linux image and use that on a USB stick to eliminate the driver issue you're having. Interface is identical
Click to expand...
Click to collapse
So I tried Ubuntu. Problem isn't from Drivers. It's because my Windows or linux didn't ever got a chance to enter fastboot so they can load preload drivers properly.
In Windows, Mediatek USB Port is the only driver that get loaded, and that for only an instant then it disappears in Device Manager.
In Linux according to this Tutorial everything is fine but SP Flash Tool gives me a " ERROR : STATUS_ERR (-1073676287) , MSP ERROE CODE : 0x00. "
Based on this chinese site I should find my Vendor Id and Product Id specific to my system (or is it my chipset?) and then change some files but how do I get linux to recognize mediatek usb device first when It needs to enter fastboot for that to happen.
Is there any way to manually add it?
EDIT: So After some reading I realized that I have to get my phone to fastboot first to get the drivers recognized. In windows as far as I know there is no way for manually adding 'Location' to Drivers. what about Linux?
I think you're talking about a soft-brick and I'm talking about a hard-brick. If you can get to fastboot, it's a soft-brick.
Hold the volume down and power buttons simultaneously for 1min and see if your screen changes.
Don't worry about the Linux drivers, if your phone is in the correct mode, it'll work.
I don't think it's a Soft-Brick (unless Hard-Brick means even the display not turning up at all), Holding them for a minute with battery charged doesn't do anything. As soon as it boots back up it starts getting caught in Booting until Redmi logo and staying there for 2-3 seconds then reboots. I tried to hold Volume Down + Power for 3 minutes while caught in this bootloop but no fastboot. I'll retry when battery discharges again. first without usb cable attached then with.
Thanks for taking time to work this through with me. Nowadays with all service centers being closed it's really a nightmare to have something you need on internal storage and not being able to access it. First thing I'll do after this is to buy a 128GB SD card to store the important stuff.
By the way should I just use the Live Ubuntu or Install it to see if the problem is from being a live image.
When I hard bricked my phone, I didn't have anything but that white led when I plugged it in. If you have the redmi logo, should mean there is hope. I've only ever entered DA mode when I had a hard brick.
This might be one of those situations where letting the battery drop to 0% would allow you to access fastboot. MiFlash only works in fastboot and DA mode I believe. What happens when you hold volume up and power for a minute while plugged in to your computer? Run "ADB devices" to start the adb service first
I doubt it would make a difference live to installed, but it's your call if you have the time.
With Phone in Bootloop mode Holding Either Vl+ and Power or Vl- and Power doesn't make a difference.
With Phone Off and USB detached It's the same.
With USB attached Vol+ and Power for over 3 Mins result in Device Manger listing 'Mediatek USB Port' for as long as display remains 'dark but bright' (for 2-3 seconds then shuts down and turns itself back on). removing it when phone suddenly shuts down. when USB is detached phone remains shutdown.
With USB attached Vol- and Power for over 3 Mins result in Phone's Display Brightening for 5 seconds no device listing in Device Manager nor entering fastboot or being recognized by adb or fastboot (set on a permanent re-checking by a cmd script). then phone shuts itself down and back on.
LED situation:
With Vol+ and Power with USB attached LED when phone is Off is Fullbright. When Display Brightens It turns off.
With Vol- and Power with USB attached LED when Phone is Off Blinks Once Fullbright and then remains Semi-bright whether phone is on until shutdown and the Blinks Fullbright again.
I Live in Iran and with sanctions there is no way to pay anyone overseas. Unless they're willing to risk accepting cryptocurrencies from an Iranian , my only chance if I can't work it out is to wait till unofficial service centers here open.
Your phone only being detected for 5 seconds is supposed to happen. It checks for a signal from so flash and if it doesn't see it, drops off.
I'm not sure paying someone to remotely flash your phone will work if SP Flash isn't even trying or detecting your phone. With mine, it would detect and try to flash (red bar sitting at 100%) before throwing an error.
Try letting your battery die, if that doesn't work, maybe the test point mod will work. Otherwise, I think your only option is a service center.
Hello,
I own a OnePlus 3, running stock firmware (up to date). I never tinkered much with it*: it has never been rooted and the bootloader stayed locked.
Yesterday I have been welcomed by a white on black text saying “The dm-verity is not started in enforcing mode and may not work properly – your device will boot in 5 seconds”. Letting it continue the boot sequence shows the 1+ logo and then the phone becomes unresponsive with a totally black screen (pink notification led on though).
Pressing volume key on the dm-verity message reveal more options : Power off, Restart, Recovery, Fastboot, Back to previous page.
Recovery seems to restart the phone and bring me back to the dm-verity message.
Fastboot options (Start, Restart bootloader, Recovery mode) do nothing or bring me back to the dm-verity screen too.
What I have tried so far :
- Booting it with power button+vol up or power + volume dows ;
- Testing that is is seen by the fastboot command from my laptop (it is) ;
- Opening the phone and disconnecting the battery for several minutes and reconnecting the battery (does nothing).
Did I missed something ? Is there a way to have it working again and back-up my data ?
Any help greatly appreciated !
Rodoro said:
Hello,
I own a OnePlus 3, running stock firmware (up to date). I never tinkered much with it*: it has never been rooted and the bootloader stayed locked.
Yesterday I have been welcomed by a white on black text saying “The dm-verity is not started in enforcing mode and may not work properly – your device will boot in 5 seconds”. Letting it continue the boot sequence shows the 1+ logo and then the phone becomes unresponsive with a totally black screen (pink notification led on though).
Pressing volume key on the dm-verity message reveal more options : Power off, Restart, Recovery, Fastboot, Back to previous page.
Recovery seems to restart the phone and bring me back to the dm-verity message.
Fastboot options (Start, Restart bootloader, Recovery mode) do nothing or bring me back to the dm-verity screen too.
What I have tried so far :
- Booting it with power button+vol up or power + volume dows ;
- Testing that is is seen by the fastboot command from my laptop (it is) ;
- Opening the phone and disconnecting the battery for several minutes and reconnecting the battery (does nothing).
Did I missed something ? Is there a way to have it working again and back-up my data ?
Any help greatly appreciated !
Click to expand...
Click to collapse
It might be a hardware issue since you did not meddle with it. If so, you will have to go to the service center.
Before that, it is worth trying out the various Unbrick Tools available in the OP 3 forum. Search for them and try a few. Sometimes it requires repeated attempts before the phone responds. I know because i have gone through the unbrick procedure earlier. Please note that the tool is different for 3 & 3T.
Best of luck!
EDIT:
Before attempting anything, backup your data to the PC with adb commands (as it is working now, according to you). It is possible and search for it.
TNSMANI said:
It might be a hardware issue since you did not meddle with it. If so, you will have to go to the service center.
Before that, it is worth trying out the various Unbrick Tools available in the OP 3 forum. Search for them and try a few. Sometimes it requires repeated attempts before the phone responds. I know because i have gone through the unbrick procedure earlier. Please note that the tool is different for 3 & 3T.
Best of luck!
EDIT:
Before attempting anything, backup your data to the PC with adb commands (as it is working now, according to you). It is possible and search for it.
Click to expand...
Click to collapse
Thanks for your feedback TNSMANI, I’ll give those unbrick tool a try. As for adb it’s not working unfortunately… but that was expected given I never bothered activating USB debugging. Fastbook commands do work but I can’t do much with them regarding data recovery.
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Call whoever you bought the phone from and do warranty claim.
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Baumhouse said:
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Click to expand...
Click to collapse
rao_hamza said:
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Click to expand...
Click to collapse
rao_hamza said:
Hi there,
I am looking for some guidance on my bricked Pixel 6 Pro.
I transfered the data from my old pixel, but then decided to do a full flash to refresh. Downloaded the stock image from google, used the fastboot-all script to flash the phone, but as soon as it was done, I never reboot. my phone is looking completely dead since.
Attempt # 1
- black screen, with no sound to any actions of response to any key combination (power or volume keys).
- tried holding the power button for 60 secs, no response
- tried holding power and volume down, no response
- tried holding power and volume up, no response
- when I plug the phone on charge, no response. neither the charging display.
Atempt # 2
- Only time the phone shows some sign of life, is when I connect the phone to my PC, it makes a sound of detecting a device, but then instantly it get a disconnect sound, (in 2-3 sec).
- I tried holding the power button, while plugged in. it makes a sound of usb detection, (but no visual response on the phone) after holder for 30 secs, it makes another sound of usb detach.
- While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone.
Not sure, if I have bricked the bootloader, and if yes, what can be done? Any guidance in this regards will be highly appreciated.
Thanks
Click to expand...
Click to collapse
Bootloader unlocked?
cultofluna said:
Bootloader unlocked?
Click to expand...
Click to collapse
If I remeber correctly flashing factory images forces you to unlock the device. So yes, the bootloader of rao_hamza's device should be unlocked.
From memory you can revive it through QPST and orher Qualcomm utilities, however hard part is to get the files. the phone is too new and many shops dont have the unlock tools yet.
" While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone. " - this is still good news, as phone is being detected by windows, try to install Qualcomm drivers and see if you can get it to boot into EDL. GOOD LUCK.
Pixel 6 uses Google's own new Tensor chip - so no Qualcomm tools
Like @Baumhouse I went through something similar. Two things for me: it took way longer to hold power and volume down than any other phone I've owned. I was seriously concerned I wasn't going to get there. Two, the factory images all made it to fastbootd and then failed all because I hadn't updated to the latest SDK.
Just throwing this out in hopes you don't have to send it back.
What @ridobe said. Make sure you're using the latest official Google Platform Tools (there's a link in my thread at the top of my signature below if you need it, or just Google for it). If I had a nickel every time someone didn't update the tools when they went to use them...
roirraW edor ehT said:
What @ridobe said. Make sure you're using the latest official Google Platform Tools (there's a link in my thread at the top of my signature below if you need it, or just Google for it). If I had a nickel every time someone didn't update the tools when they went to use them...
Click to expand...
Click to collapse
This and a bad/wrong cable seem to be the most common culprits
ridobe said:
Like @Baumhouse I went through something similar. Two things for me: it took way longer to hold power and volume down than any other phone I've owned. I was seriously concerned I wasn't going to get there. Two, the factory images all made it to fastbootd and then failed all because I hadn't updated to the latest SDK.
Just throwing this out in hopes you don't have to send it back.
Click to expand...
Click to collapse
Any idea how long you had to hold that button combinaiton? I tried longer, maybe 60 sec, but still no response from the phone.
tids2k said:
From memory you can revive it through QPST and orher Qualcomm utilities, however hard part is to get the files. the phone is too new and many shops dont have the unlock tools yet.
" While I am experimentating with PC connection, I also tried fastboot reboot command, it only shows waiting for a device and nothing happens, either on the console or phone. " - this is still good news, as phone is being detected by windows, try to install Qualcomm drivers and see if you can get it to boot into EDL. GOOD LUCK.
Click to expand...
Click to collapse
What is EDL? and had the Google usb drivers installed, to get the fastboot working.
Baumhouse said:
I struggled with a soft bricked / bootlooping phone after removing Magisk. Although my phone at least booted to bootloader and a connection via fastboot was working, the factory images wouldn't flash properly. Google support couldn't help me and I thought I had to send it to repair.
In the end I could solve the issue by switching to the Android SDK 31. I know your case is different, because your phone is bricked worse than mine was, but you could give it a try.
Click to expand...
Click to collapse
Yes, I don't know who to get into a bootloader in this situation, if that were working I would have some hope.
If you can get to the bootloader you can use google's flashing website, flash.android.com. I just use that to go back to stock, even with an unlocked bootloader.
pysklona said:
If you can get to the bootloader you can use google's flashing website, flash.android.com. I just use that to go back to stock, even with an unlocked bootloader.
Click to expand...
Click to collapse
Thanks @pysklona. you are right, but the problem is I can't get into the bootloader. This is what I am seeking help for.
rao_hamza said:
Thanks @pysklona. you are right, but the problem is I can't get into the bootloader. This is what I am seeking help for.
Click to expand...
Click to collapse
Sorry, misread the post.
@pysklona came here because I'm in the same boat, hard-bricked my device after running the flash-all script. Was using the most recent version of platform tools and the brand new cable that came with the phone.
Was getting the same result, attaching it to a windows pc makes the attached device chime, but disconnects after a few seconds. It came up first as "Setting up Pixel ROM Recovery". I let it sit overnight and now it doesn't auto-disconnect and I get a serial device under com3 on windows. Attaching it to macos gives me a "Pixel ROM Recovery" device. Despite "recovery" in the name, I think it's actually in EDL mode, not recovery mode. No devices come up for adb or fastboot on windows, linux or macos. Screen is completely blank no matter what.
Not being a Qualcomm chip makes this whole process from here a bit of an unknown, but will assume the process for recovery is more or less the same. Looking into QPST/MsmDownloadTool/OpenPST, although as pointed out, I'm not sure any of those tools will work since this isn't a qualcomm chip. MsmDownloadTool is for oneplus, but maybe something can be modded.
ootri said:
@pysklona came here because I'm in the same boat, hard-bricked my device after running the flash-all script. Was using the most recent version of platform tools and the brand new cable that came with the phone.
Was getting the same result, attaching it to a windows pc makes the attached device chime, but disconnects after a few seconds. It came up first as "Setting up Pixel ROM Recovery". I let it sit overnight and now it doesn't auto-disconnect and I get a serial device under com3 on windows. Attaching it to macos gives me a "Pixel ROM Recovery" device. Despite "recovery" in the name, I think it's actually in EDL mode, not recovery mode. No devices come up for adb or fastboot on windows, linux or macos. Screen is completely blank no matter what.
Not being a Qualcomm chip makes this whole process from here a bit of an unknown, but will assume the process for recovery is more or less the same. Looking into QPST/MsmDownloadTool/OpenPST, although as pointed out, I'm not sure any of those tools will work since this isn't a qualcomm chip. MsmDownloadTool is for oneplus, but maybe something can be modded.
Click to expand...
Click to collapse
Thanks for sharing your experience. I just returned the device and got myself a new one.
anyways, i am not sure what is causing this hard brick. thats is something we all should be careful about it.
same thing here. pixel 6 from google store. magisk installed on the december update and i downgraded to the november one using the flash-all.bat script. phone reboots and am told the software is corrupt
reboot back into fastboot mode, run the script again. and get this software is corrupt message again
this time I cant' even boot into fastboot/bootloader mode. and plugging the phone into windows gives me the "pixel rom recovery" message
phone seems dead (black screen, not responding to hardware buttons)
any other solutions than to get it replaced?
Hmm, maybe plug it in to a PC via USB to supply it with power (maybe the battery is down) and just do a very long press of the power button - at least 30 seconds - until the phone starts up. If it does and isn't in fastboot you could try "Power-VolDown" to get into fastboot...
If it just doesn't react to all of this and waiting a bit (in case the battery was at 0% and needs some minimal charge) I think a replacement is the only way to go....
Enddo said:
same thing here. pixel 6 from google store. magisk installed on the december update and i downgraded to the november one using the flash-all.bat script. phone reboots and am told the software is corrupt
reboot back into fastboot mode, run the script again. and get this software is corrupt message again
this time I cant' even boot into fastboot/bootloader mode. and plugging the phone into windows gives me the "pixel rom recovery" message
phone seems dead (black screen, not responding to hardware buttons)
any other solutions than to get it replaced?
Click to expand...
Click to collapse
You could try Official Google Android Flash Tool. It's merely another method of doing what you effectively tried, but from what I've read, it's helped some folks. Sadly, others have reported that the Official Google Pixel Update and Software Repair hasn't been updated for the P6P yet.
If that doesn't help, hang in there. There are others in here who will likely have even better advice.
roirraW edor ehT said:
You could try Official Google Android Flash Tool. It's merely another method of doing what you effectively tried, but from what I've read, it's helped some folks. Sadly, others have reported that the Official Google Pixel Update and Software Repair hasn't been updated for the P6P yet.
If that doesn't help, hang in there. There are others in here who will likely have even better advice.
Click to expand...
Click to collapse
appreciate the links. right now, I can't even get into fastboot/bootloader mode. so neither of those tools detect the phone.
@s3axel the battery definitely isn't low. I charged it up before all this specifically so that I know it had plenty of juice (was at 93% or something).
I'm thinking maybe after letting the battery die, charging it back up will let me boot into a special boot mode
but any other ideas, please, I'm all ears