I have a plan to re-flash my LGOGP E988 stock kitkat not rooted and i already downloaded the files i need but when i try to enter download mode based on what i read in all thread regarding to my unit (vol+ & vol - + usb plug into computer), thers no luck for me.. It always go to charging and not in download mode. I already installed required driversCan you help me?
Combination i tried that was no luck(usb plug in computer);
1. Off phone>remove battery>hold both volume>reinsert battery>plug micro usb
2. Off phone>hold both vol.>plug micro usb
3. Off phone>hold +vol >plug micro usb(vice versa, also use -vol)
4. Off phone> hold both vol. >Power button (go to hard reset)
5. Remove battery> hold both vol.>insert micro usb
Please help me i will update things that i already try.
Thanks in advance..
And i know thia will be benefit other members that getting hard times to enter download mode.
robtoman said:
I have a plan to re-flash my LGOGP E988 stock kitkat not rooted and i already downloaded the files i need but when i try to enter download mode based on what i read in all thread regarding to my unit (vol+ & vol - + usb plug into computer), thers no luck for me.. It always go to charging and not in download mode. Can you help me?
Combination i tried that was no luck;
1. Off phone-remove battery-hold both volume-reinsert battery-plug usb to computer
2. Off phone- hold both vol.-plug usb to computer
3. off phone- hold +vol -plug usb tomputer (vice versa alao use -vol)
4. Off phone- hold both vol. Power button (go to hard reset)
Please help me i will update things that i already try?thanks in advance..
Click to expand...
Click to collapse
Skip the reinsert battery part in your item #1:
1) Remove battery
2) Hold Volume plus and minus keys down
3) Insert USB cable while still continuing to hold down those two buttons.
WIthin 1-2 seconds you should have download mode. When download mode appears, then re-insert battery. For sure you're not going into charging mode with no battery to charge. This is the method I always use, and it always works (aside from hard-brick situations, but you can access battery charging mode/graphics, which surely means that ain't you).
not works.
culot said:
Skip the reinsert battery part in your item #1:
1) Remove battery
2) Hold Volume plus and minus keys down
3) Insert USB cable while still continuing to hold down those two buttons.
WIthin 1-2 seconds you should have download mode. When download mode appears, then re-insert battery. For sure you're not going into charging mode with no battery to charge. This is the method I always use, and it always works (aside from hard-brick situations, but you can access battery charging mode/graphics, which surely means that ain't you).
Click to expand...
Click to collapse
I realy appreciate your help but i try it several time but still not enter download mode. Just always show the boot logo of LG then off then show again the boot logo. Why am i getting this? Can anyone has their own solutions?
robtoman said:
I realy appreciate your help but i try it several time but still not enter download mode. Just always show the boot logo of LG then off then show again the boot logo. Why am i getting this? Can anyone has their own solutions?
Click to expand...
Click to collapse
What does your computer say when you plug it in? If in Windows check Device Manager and see what your phone is being recognized as. Can you access the phone's contents via USB cable from your computer? Does ADB recognize it at all? Or does it just loop like that, not starting?
Also, it sometimes takes several tries to get it into download mode, as if you're holding the buttons down and not timed just right, the phone ignore your attempt. Make sure you do not let go of both volume buttons even after you plug in the USB cable, you must continue to hold them down for a couple of seconds (until the DL mode appears). Don't even think about putting the battery back in until you see that download mode box. Try that a few times maybe? If it doesn';t work ,maybe you're boned.
robtoman said:
I realy appreciate your help but i try it several time but still not enter download mode. Just always show the boot logo of LG then off then show again the boot logo. Why am i getting this? Can anyone has their own solutions?
Click to expand...
Click to collapse
remove battery and place it again. then press both volume+ and Volume - . By keeping pressed both buttons insert your usb cable. don't release pressed buttons until its in download mood. by the way install unified adb driver for android by koush if your using windows 8.1 otherwise lg official driver is ok
I've got a Samsung Galaxy Tab S 8.4" which no longer has a working display. I want to back up as much of it as I can, so I've set to work on installing TWRP. I already installed and used it successfully on an identical device (but with the screen working!), but this time round, it just doesn't work.
TL;DR: My questions: Is there any way to add TWRP to my device without using Download Mode? Is there any way to check if TWRP is installed? And is there any way to, once I'm in Download Mode, determine that without exiting and without a display?
My process: I've tried getting into Download Mode both by shutting down, then holding the power, volume down, and home buttons for ten or so seconds, then following up with a volume up press to confirm that I want to use download mode; and by just typing reboot download in adb. I've then used Odin to flash it with TWRP. Odin shows a PASS, so I wait for the tablet to reboot into the normal mode.
Once there, I've tried to get into TWRP by both shutting down, then holding the power, volume up, and home buttons for ten or so seconds; and by just typing reboot recovery in adb. But, no matter how long I wait, my device never reconnects to my computer, and adb shell can't connect to it.
When I've rebooted into recovery, I seem to be able to press the power button once, and it reboots into the normal boot mode; this indicates to me that it's in the normal Recovery Mode, since this isn't default TWRP behaviour. That would mean that TWRP hasn't been successfully installed.
I came across this thread, which suggested that using Odin to flash a device while it's not in Download Mode would likely have no effect. My figuring, then, is that I haven't successfully booted into Download Mode ever.
Interestingly, when I ran Odin during what I thought was Download Mode, it did seem to restart the device when it was done (at least, after a bit I could connect to it normally with adb).
My question, then: Is there any way to add TWRP to my device without using Download Mode? Is there any way to check if TWRP is installed? And is there any way to, once I'm in Download Mode, determine that without exiting and without a display?
I know it's a bit of a tricky one, so :good: if you can think of an answer to any of those.
I wonder if the hdmi adaptors would work in recover, they are quite cheap to buy.
Your issue is likely that you're not manually booting to recovery IMMEDIATELY after flashing with Odin. TWRP is obviously successfully flashing.
You need to disable auto-reboot then when odin states PASS, force manual reboot by holding POWER + HOME + VOL DOWN for a few seconds then change to VOL UP whilst still holding the other buttons.
This is all gonna come down to timing, so you may have to do it several times until you get it.
In any case if all you need to back up is your stuff stored on internal storage, you don't need twrp for that. Just connect the tablet to the PC and use MTP to backup what you need.
Hi there. After (an attempt) to unlock the bootloader of my A50 and installing TWRP Recovery (TWRP_A50_Magisk_Prepatched) i find myself in an orange bootstate. I can't get it into recovery, download or fastboot mode. It seems like a full brick. I can't even power off the device. Only Volume up, Volume down and Power button let's the device reboot but then the same boot problems appear. Is there anything i can do to recover my phone?
Text of first screen when booting up:
"The phone's bootloader is unlocked and it's software integrity can't be verified. Andy data on this phone may be vulnerable to attackers. Don't store any important or sensitive information on this phone". Press power key to continue"
Text of second screen when booting up:
"The phone is not running Samsung's official software. You may have problems with features or security and you won't be able to install software updates"
Any ideas!?
flash stock via odin
nikolas60 said:
flash stock via odin
Click to expand...
Click to collapse
I have the same problem described as above. To use odin you need access to the download menu. Personally, i can not even access the download menu using any cobination of volume up-down & power combination...
RestrictedPower said:
I have the same problem described as above. To use odin you need access to the download menu. Personally, i can not even access the download menu using any cobination of volume up-down & power combination...
Click to expand...
Click to collapse
caztricum said:
Hi there. After (an attempt) to unlock the bootloader of my A50 and installing TWRP Recovery (TWRP_A50_Magisk_Prepatched) i find myself in an orange bootstate. I can't get it into recovery, download or fastboot mode. It seems like a full brick. I can't even power off the device. Only Volume up, Volume down and Power button let's the device reboot but then the same boot problems appear. Is there anything i can do to recover my phone?
Text of first screen when booting up:
"The phone's bootloader is unlocked and it's software integrity can't be verified. Andy data on this phone may be vulnerable to attackers. Don't store any important or sensitive information on this phone". Press power key to continue"
Text of second screen when booting up:
"The phone is not running Samsung's official software. You may have problems with features or security and you won't be able to install software updates"
Any ideas!?
Click to expand...
Click to collapse
Try connecting your phone to your PC with the USB Type C cable, and do VolDown + Power to reboot the phone, and the moment the screen turns black, press VolUp + VolDown. It'll bring you to a different screen where you can press VolUp to go into download mode for flashing the stock firmware via Odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
jtanhw said:
Try connecting your phone to your PC with the USB Type C cable, and do VolDown + Power to reboot the phone, and the moment the screen turns black, press VolUp + VolDown. It'll bring you to a different screen where you can press VolUp to go into download mode for flashing the stock firmware via Odin. I got my stock firmware from (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
This did it for me! Many thanks...
jtanhw said:
download mode for flashing the stock firmware via Odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
I had the same problem and managed to get back to the Download Page.
How do I find out what is the correct region of the correct Modem Version of my phone? It's an S10 (intl unlocked) that I bought in the US from Amazon.
TheAsker70 said:
I had the same problem and managed to get back to the Download Page.
How do I find out what is the correct region of the correct Modem Version of my phone? It's an S10 (intl unlocked) that I bought in the US from Amazon.
Click to expand...
Click to collapse
You can find answers in the S10 forum. But I think the steps will be the same (this is A8 device/forum).
Rexton270 said:
You can find answers in the S10 forum. But I think the steps will be the same (this is A8 device/forum).
Click to expand...
Click to collapse
My bad. Apologize. Will head over there. Thanks!
No bother. Hope you are sorted by now.
this is the exact same problem that goes for me with my samsung a505gn, i flashed a twrp 3.3.1-2_zvox and im stuck at this state. i found my stock firmware at the link provided above, but there are multiple types of a505gn stock firmware (XTC, SMA, GLB), question is, how do i know the correct type of stock firmware to reinstall to my phone, hence, having a limited information of the phone because of this problem (which is stuck at orange bootstate).
Same Problem
caztricum said:
This did it for me! Many thanks...
Click to expand...
Click to collapse
for now work on not sir
i have same problem stuk n auto restart
if u work can u help me thanks
jtanhw said:
try connecting your phone to your pc with the usb type c cable, and do voldown + power to reboot the phone, and the moment the screen turns black, press volup + voldown. It'll bring you to a different screen where you can press volup to go into download mode for flashing the stock firmware via odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your model number - sm-a505f/sm-a505fn/sm-a505fm, and select the correct region. Also, select the correct modem version (the last 4 letters/number of the item to download). Then, follow the "flashing guide" at the bottom of the samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
thank you very much
thanks for your comment, its help me. my Samsung A50 hanged on boot-loader and loop turn on/off.
Is there a way to install twrp if the problem is like this every time I try to install the twrp it came to this problem. Please help me
jtanhw said:
Try connecting your phone to your PC with the USB Type C cable, and do VolDown + Power to reboot the phone, and the moment the screen turns black, press VolUp + VolDown. It'll bring you to a different screen where you can press VolUp to go into download mode for flashing the stock firmware via Odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
Hi this helped me many thanks <3
jtanhw said:
Try connecting your phone to your PC with the USB Type C cable, and do VolDown + Power to reboot the phone, and the moment the screen turns black, press VolUp + VolDown. It'll bring you to a different screen where you can press VolUp to go into download mode for flashing the stock firmware via Odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
thank you so much you just helped me save my phone
peace keeper said:
thank you so much you just helped me save my phone
Click to expand...
Click to collapse
Have you got the a21s? As can't root it, as every twrp source I use soft bricks the phone, or just bootloops, or goes into error at boot up and stops half way. Was thinking trying other custom recovery. Any tips m8?
jtanhw said:
Try connecting your phone to your PC with the USB Type C cable, and do VolDown + Power to reboot the phone, and the moment the screen turns black, press VolUp + VolDown. It'll bring you to a different screen where you can press VolUp to go into download mode for flashing the stock firmware via Odin. I got my stock firmware from https://samfrew.com/all/page/2/#t (you'll need to search for your Model Number - SM-A505F/SM-A505FN/SM-A505FM, and select the correct Region. Also, select the correct Modem Version (the last 4 letters/number of the item to download). Then, follow the "Flashing Guide" at the bottom of the Samfrew page where you downloaded your firmware.
Click to expand...
Click to collapse
My phone is Realme 6 it doesnt take me anywhere my laptop only does the plugging in and plugging out sound all the time and when I let go of the volume buttons the bootloop happens again
caztricum said:
Hi there. After (an attempt) to unlock the bootloader of my A50 and installing TWRP Recovery (TWRP_A50_Magisk_Prepatched) i find myself in an orange bootstate. I can't get it into recovery, download or fastboot mode. It seems like a full brick. I can't even power off the device. Only Volume up, Volume down and Power button let's the device reboot but then the same boot problems appear. Is there anything i can do to recover my phone?
Text of first screen when booting up:
"The phone's bootloader is unlocked and it's software integrity can't be verified. Andy data on this phone may be vulnerable to attackers. Don't store any important or sensitive information on this phone". Press power key to continue"
Text of second screen when booting up:
"The phone is not running Samsung's official software. You may have problems with features or security and you won't be able to install software updates"
Any ideas!?
Click to expand...
Click to collapse
caztricum said:
Hi there. After (an attempt) to unlock the bootloader of my A50 and installing TWRP Recovery (TWRP_A50_Magisk_Prepatched) i find myself in an orange bootstate. I can't get it into recovery, download or fastboot mode. It seems like a full brick. I can't even power off the device. Only Volume up, Volume down and Power button let's the device reboot but then the same boot problems appear. Is there anything i can do to recover my phone?
Text of first screen when booting up:
"The phone's bootloader is unlocked and it's software integrity can't be verified. Andy data on this phone may be vulnerable to attackers. Don't store any important or sensitive information on this phone". Press power key to continue"
Text of second screen when booting up:
"The phone is not running Samsung's official software. You may have problems with features or security and you won't be able to install software updates"
Any ideas!?
Click to expand...
Click to collapse
I HAD the same issue an I resolved it.
There are 2 methods to overcome this problem.
I even wrote a PDF and attached here in this post.
Below is SOME content from the PDF so it could be easy for users to find it on Google. I still strongly recommend you to refer to the PDF attached as it has pictures as well.
Samsung Galaxy M31 / Samsung M31 Screen is stuck on the following error message / error screen:
‘This phone’s bootloader is unlocked and the software integrity can’t be verified. Any data on this phone may be vulnerable to attackers. Don’t store any important or sensitive information on the phone.’
‘The phone is not running Samsung’s official software. You may have problems with features or security. And you won’t be able to install software updates.’ (error screen looks like below):
I was using correct TWRP and I was on Android 11 One UI 3.1.
Just to experiment, I flashed wrong TWRP version which was meant for Android 10 while being on Android 11. And so this problem started. Stuck on the error screen. Phone will not power off or on. Could not even enter the bootloader screen. Nothing works whatever keys I press. The same screen comes up. When the phone goes off and the phone will not accept charging that mean even you it whole night connected to charger, phone will not be charged- the same error screen.
So, the battery was not charging (my battery was at 24% just before this tragedy happened. It was late night and I thought of waking up tomorrow and plug in charger for an hour thinking if its battery is quite charged then I will follow Fix Method 2).
I woke up next morning and the phone was off (Battery drained fully). To this I was happy thinking that I can now hold Volume + and Power key and connect USB cable to enter Bootloader. When I did that phone would enter bootloader and gets switched off automatically (remember the battery was drained completely, charger too failed to charge battery and phone is not drawing enough power from USB port to stay on bootloader. On bootloader screen the phone’s display is fully on so more power usage).
Now I knew that the USB port is not proving enough power so that the phone could remain On while in bootloader when I hold Volume + and Power key and connect USB cable to enter Bootloader. I know for sure that Fix Method 2 will fix this for sure but it’s quite tiring.
So I referred to my PC manual to figure out which USB port provides maximum power. I found the right port (refer pic below):
So now I figured out 5 Volts port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
If you don’t know which USB Port is 5 Volts then I recommend you to try all the ports and try getting to bootloader screen.
So when the phone was off, I pressed and hold the Volume up and Volume down key and with other hand I connected USB cable and now the phone went in bootloader and then I quickly flashed the right TWRP. Disconnected the USB cable and put the phone to charge and now it was accepting charge. Phone was back into life.
So I resolved it by Fix Method 1 below:
Fix Method 1: On my PC, I located the 5 Volts USB port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
Entered Bootloader screen.
How to enter bootloader screen:
Assuming your phone is unlocked and the developers options are on and you have enabled USB debugging in Developer options and you have little knowledge of flashing firmware or TWRP via Odin.
Press and hold Volume Up and Volume down keys together with one hand and using other hand, connect USB cable to phone and release all the keys. Now phone will show bootloader screen which looks like below pic:
I quickly flashed the correct TWRP via Odin:
Flashing TWRP:
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Press the volume down + volume up button whilst the phone is connected to a pc to boot in download mode;;
· Long press vol up then confirm you want to unlock bootloader (this is needed one time only);
* Please be aware all your data will be erased including internal storage and phone will reboot!!
· Let the phone boot normally, pass the setup and connect to internet (wireless or mobile data) in order to unlock RMM;
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Use Vol up + Power + usb cable plugged to a pc to start the phone in download mode, short press vol up to confirm you want to go to download mode;
* If by any chance you see RMM state=Prenormal or KG state=Prenormal, factory reset data and redo from step 5!
TWRP screen was up. I tapped on Reboot and it did not reboot because the battery was not enough charged however I saw that TWRP Menu this means TWRP was working so the phone will boot up once it is charged.
Now I plugged in charger and was happy to see the correct charging screen (refer below pic):
I would turn power switch Off and On it quicky to know the charging percentage.
When it reached 20% I started phone (obviously by long pressing power key and it booted up just fine).
I loved myself
Fix Method 2:
Remove the phone’s back cover.
Be careful while removing the back case as you could screw the finger print sensor.
Disconnect the battery connector from motherboard and reconnect it.
Do not turn on the phone. As turning On will again get you back to the same error screen.
Put the back cover on.
Connect charger. Do not turn phone On yet. Wait for 5 min.
Do not even touch the phone.
Now you need to know the percentage of charge so do not hit the power button yet instead locate the main switch to which your charger is connected. Quickly turn Off and On and look at phone it shows charging percentage.
Once charging percentage reached around 20% you can touch your phone and power it on and it should boot up fine. It should not take more than 5 min to boot up.
Atharkhan101 said:
I HAD the same issue an I resolved it.
There are 2 methods to overcome this problem.
I even wrote a PDF and attached here in this post.
Below is SOME content from the PDF so it could be easy for users to find it on Google. I still strongly recommend you to refer to the PDF attached as it has pictures as well.
Samsung Galaxy M31 / Samsung M31 Screen is stuck on the following error message / error screen:
‘This phone’s bootloader is unlocked and the software integrity can’t be verified. Any data on this phone may be vulnerable to attackers. Don’t store any important or sensitive information on the phone.’
‘The phone is not running Samsung’s official software. You may have problems with features or security. And you won’t be able to install software updates.’ (error screen looks like below):
I was using correct TWRP and I was on Android 11 One UI 3.1.
Just to experiment, I flashed wrong TWRP version which was meant for Android 10 while being on Android 11. And so this problem started. Stuck on the error screen. Phone will not power off or on. Could not even enter the bootloader screen. Nothing works whatever keys I press. The same screen comes up. When the phone goes off and the phone will not accept charging that mean even you it whole night connected to charger, phone will not be charged- the same error screen.
So, the battery was not charging (my battery was at 24% just before this tragedy happened. It was late night and I thought of waking up tomorrow and plug in charger for an hour thinking if its battery is quite charged then I will follow Fix Method 2).
I woke up next morning and the phone was off (Battery drained fully). To this I was happy thinking that I can now hold Volume + and Power key and connect USB cable to enter Bootloader. When I did that phone would enter bootloader and gets switched off automatically (remember the battery was drained completely, charger too failed to charge battery and phone is not drawing enough power from USB port to stay on bootloader. On bootloader screen the phone’s display is fully on so more power usage).
Now I knew that the USB port is not proving enough power so that the phone could remain On while in bootloader when I hold Volume + and Power key and connect USB cable to enter Bootloader. I know for sure that Fix Method 2 will fix this for sure but it’s quite tiring.
So I referred to my PC manual to figure out which USB port provides maximum power. I found the right port (refer pic below):
So now I figured out 5 Volts port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
If you don’t know which USB Port is 5 Volts then I recommend you to try all the ports and try getting to bootloader screen.
So when the phone was off, I pressed and hold the Volume up and Volume down key and with other hand I connected USB cable and now the phone went in bootloader and then I quickly flashed the right TWRP. Disconnected the USB cable and put the phone to charge and now it was accepting charge. Phone was back into life.
So I resolved it by Fix Method 1 below:
Fix Method 1: On my PC, I located the 5 Volts USB port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
Entered Bootloader screen.
How to enter bootloader screen:
Assuming your phone is unlocked and the developers options are on and you have enabled USB debugging in Developer options and you have little knowledge of flashing firmware or TWRP via Odin.
Press and hold Volume Up and Volume down keys together with one hand and using other hand, connect USB cable to phone and release all the keys. Now phone will show bootloader screen which looks like below pic:
I quickly flashed the correct TWRP via Odin:
Flashing TWRP:
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Press the volume down + volume up button whilst the phone is connected to a pc to boot in download mode;;
· Long press vol up then confirm you want to unlock bootloader (this is needed one time only);
* Please be aware all your data will be erased including internal storage and phone will reboot!!
· Let the phone boot normally, pass the setup and connect to internet (wireless or mobile data) in order to unlock RMM;
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Use Vol up + Power + usb cable plugged to a pc to start the phone in download mode, short press vol up to confirm you want to go to download mode;
* If by any chance you see RMM state=Prenormal or KG state=Prenormal, factory reset data and redo from step 5!
TWRP screen was up. I tapped on Reboot and it did not reboot because the battery was not enough charged however I saw that TWRP Menu this means TWRP was working so the phone will boot up once it is charged.
Now I plugged in charger and was happy to see the correct charging screen (refer below pic):
I would turn power switch Off and On it quicky to know the charging percentage.
When it reached 20% I started phone (obviously by long pressing power key and it booted up just fine).
I loved myself
Fix Method 2:
Remove the phone’s back cover.
Be careful while removing the back case as you could screw the finger print sensor.
Disconnect the battery connector from motherboard and reconnect it.
Do not turn on the phone. As turning On will again get you back to the same error screen.
Put the back cover on.
Connect charger. Do not turn phone On yet. Wait for 5 min.
Do not even touch the phone.
Now you need to know the percentage of charge so do not hit the power button yet instead locate the main switch to which your charger is connected. Quickly turn Off and On and look at phone it shows charging percentage.
Once charging percentage reached around 20% you can touch your phone and power it on and it should boot up fine. It should not take more than 5 min to boot up.
Click to expand...
Click to collapse
Atharkhan101 said:
I HAD the same issue an I resolved it.
There are 2 methods to overcome this problem.
I even wrote a PDF and attached here in this post.
Below is SOME content from the PDF so it could be easy for users to find it on Google. I still strongly recommend you to refer to the PDF attached as it has pictures as well.
Samsung Galaxy M31 / Samsung M31 Screen is stuck on the following error message / error screen:
‘This phone’s bootloader is unlocked and the software integrity can’t be verified. Any data on this phone may be vulnerable to attackers. Don’t store any important or sensitive information on the phone.’
‘The phone is not running Samsung’s official software. You may have problems with features or security. And you won’t be able to install software updates.’ (error screen looks like below):
I was using correct TWRP and I was on Android 11 One UI 3.1.
Just to experiment, I flashed wrong TWRP version which was meant for Android 10 while being on Android 11. And so this problem started. Stuck on the error screen. Phone will not power off or on. Could not even enter the bootloader screen. Nothing works whatever keys I press. The same screen comes up. When the phone goes off and the phone will not accept charging that mean even you it whole night connected to charger, phone will not be charged- the same error screen.
So, the battery was not charging (my battery was at 24% just before this tragedy happened. It was late night and I thought of waking up tomorrow and plug in charger for an hour thinking if its battery is quite charged then I will follow Fix Method 2).
I woke up next morning and the phone was off (Battery drained fully). To this I was happy thinking that I can now hold Volume + and Power key and connect USB cable to enter Bootloader. When I did that phone would enter bootloader and gets switched off automatically (remember the battery was drained completely, charger too failed to charge battery and phone is not drawing enough power from USB port to stay on bootloader. On bootloader screen the phone’s display is fully on so more power usage).
Now I knew that the USB port is not proving enough power so that the phone could remain On while in bootloader when I hold Volume + and Power key and connect USB cable to enter Bootloader. I know for sure that Fix Method 2 will fix this for sure but it’s quite tiring.
So I referred to my PC manual to figure out which USB port provides maximum power. I found the right port (refer pic below):
So now I figured out 5 Volts port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
If you don’t know which USB Port is 5 Volts then I recommend you to try all the ports and try getting to bootloader screen.
So when the phone was off, I pressed and hold the Volume up and Volume down key and with other hand I connected USB cable and now the phone went in bootloader and then I quickly flashed the right TWRP. Disconnected the USB cable and put the phone to charge and now it was accepting charge. Phone was back into life.
So I resolved it by Fix Method 1 below:
Fix Method 1: On my PC, I located the 5 Volts USB port and plugged the original white Samsung M31 USB cable into one (refer the pic below):
Entered Bootloader screen.
How to enter bootloader screen:
Assuming your phone is unlocked and the developers options are on and you have enabled USB debugging in Developer options and you have little knowledge of flashing firmware or TWRP via Odin.
Press and hold Volume Up and Volume down keys together with one hand and using other hand, connect USB cable to phone and release all the keys. Now phone will show bootloader screen which looks like below pic:
I quickly flashed the correct TWRP via Odin:
Flashing TWRP:
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Press the volume down + volume up button whilst the phone is connected to a pc to boot in download mode;;
· Long press vol up then confirm you want to unlock bootloader (this is needed one time only);
* Please be aware all your data will be erased including internal storage and phone will reboot!!
· Let the phone boot normally, pass the setup and connect to internet (wireless or mobile data) in order to unlock RMM;
· Make sure OEM Unlock is ON in developer settings;
· Turn off the phone;
· Use Vol up + Power + usb cable plugged to a pc to start the phone in download mode, short press vol up to confirm you want to go to download mode;
* If by any chance you see RMM state=Prenormal or KG state=Prenormal, factory reset data and redo from step 5!
TWRP screen was up. I tapped on Reboot and it did not reboot because the battery was not enough charged however I saw that TWRP Menu this means TWRP was working so the phone will boot up once it is charged.
Now I plugged in charger and was happy to see the correct charging screen (refer below pic):
I would turn power switch Off and On it quicky to know the charging percentage.
When it reached 20% I started phone (obviously by long pressing power key and it booted up just fine).
I loved myself
Fix Method 2:
Remove the phone’s back cover.
Be careful while removing the back case as you could screw the finger print sensor.
Disconnect the battery connector from motherboard and reconnect it.
Do not turn on the phone. As turning On will again get you back to the same error screen.
Put the back cover on.
Connect charger. Do not turn phone On yet. Wait for 5 min.
Do not even touch the phone.
Now you need to know the percentage of charge so do not hit the power button yet instead locate the main switch to which your charger is connected. Quickly turn Off and On and look at phone it shows charging percentage.
Once charging percentage reached around 20% you can touch your phone and power it on and it should boot up fine. It should not take more than 5 min to boot up.
Click to expand...
Click to collapse
Hi, friend. I have the same problem. But I don't even have a bootloader. When I log in, I just get a black screen.
Hi,
After wiping /system on my Razer Phone, I tried to sideload an image, and the recovery crashed and the phone rebooted. Since, it has been restarting indefinitely, being on the Razer logo and the "Your device is insecure" message.
I have tried to hard shutdown the phone with power+volume up, then holding volume down and plugging the phone, but I was unable to get download mode working...
Volume up then plugging in the phone to my computer did not help either. Both volumes either.
If someone has an idea on how to get it into download mode, I'd really be grateful. Thanks.
Try power and up for nearly a min sounds stupid I know but forces a full full power down. Otherwise wait a few days for the battery to die then plug into pc with vol down held.
Tried both. I even opened the phone, unplugged the battery, then plugged it again to force a shutdown. It never got into download mode
What type of USB cable are you using?
So I have spent hours now looking around for an answer the phone is find my phone locked and I can't remember my pin code. I have done all the tricks with the combination keys.
The usual way to get into Recovery mode is Hold V+ and power until the phone vibrates and you should be in recovery mode release the keys. (Doesn't work)
Iv read that you should have the USB cable connected from pc/laptop while you do the same holding V+ and power button... (doesn't work ether)
and download mode should be very easy just hold V+ and V- plug USB cable from pc/laptop and you should get into download mode by pressing V+. Will only show charging Icon and that's its.
So is it possible to turn off this modes from the manufactor? Or is this a completely new security future? How can you use odin? How can you wipe the cache? If you end up having some issues.
Im going nuts....
No way to get into fastboot ether. So if anyone know why this is happening to me or got any solution I would appreciate it.
Plug in your cable with the phone turned on. Hit Power Off and wait for the phone to fully turn off. The charging logo will show up so let the animation do its thing. After maybe 20 seconds, press Volume up + Power and keep them pressed until you boot to recovery. If the command wasn't recorded in the first place and the phone is still off after more than 15 seconds, let go of the buttons and press them again and keep them pressed until it boots in Recovery
dragos281993 said:
Plug in your cable with the phone turned on. Hit Power Off and wait for the phone to fully turn off. The charging logo will show up so let the animation do its thing. After maybe 20 seconds, press Volume up + Power and keep them pressed until you boot to recovery. If the command wasn't recorded in the first place and the phone is still off after more than 15 seconds, let go of the buttons and press them again and keep them pressed until it boots in Recovery
Click to expand...
Click to collapse
It will not work. How the hell should I be able to cle3ar cache if I got a boot loop ??? They can't just turn off recovery mode mand download mode??? This is so strange even paying for a frp reset but not even he does know what wrong??? Can they turn off fastboot, recovery mode and Download mode on this new phones? Is it because its locked with find my phone? 1 week researching now. It will only vibrate. And my PC cant find my phone anymore worked fine 30min ago nothing has changed... So annoying never seen this happened before every combination with buttons to get in any mode doesn't work only vibrates and go to pin lock screen...
Take it to a Samsung Experience center at best buy. Or send it into Samsung for repair.
download mode:
Turn off phone
plug cable in pc but not in phone
pres "volume +" and "volume -" in the same time
plug cable in phone
recovery mode:
plug cable in pc and s22
power off
press "volume +" and power
wait until see recovery mode
starciti said:
download mode:
Turn off phone
plug cable in pc but not in phone
pres "volume +" and "volume -" in the same time
plug cable in phone
recovery mode:
plug cable in pc and s22
power off
press "volume +" and power
wait until see recovery mode
Click to expand...
Click to collapse
thats a solid advice assuming his bootloader/recovery/download mode is fully functional then this advice works, in his case and in mine too it does not work and trying to get to the root of the problem is the key. In my case recovery mode gives error on screen so it may have to do with the way firmware is installed as these modes are not accessible.
have you sorted it out? Its nearly a year onwards =)
CrispShadow19 said:
thats a solid advice assuming his bootloader/recovery/download mode is fully functional then this advice works, in his case and in mine too it does not work and trying to get to the root of the problem is the key. In my case recovery mode gives error on screen so it may have to do with the way firmware is installed as these modes are not accessible.
Click to expand...
Click to collapse
This, at index 2:48 minutes.
It needs to be connected to the PC. Another screwy quirk Samsung added recently. Your button timing/sequence matters as well.
On my N10+'s you can go into recovery directly with a restart if you do it right. Otherwise they will puke on you.