Develop Bugs

Flash Question

I rooted my Unlocked xl 2 using a method I found online. Used it a couple of days rooted and decided to go back to stock so....
I downloaded the factory image, ran the flash -all.bat and everything was good. Next I went back to my boot loader to re lock it, ran the command , selected yes.
After I hit yes to re lock the boot loader I got the following error. COULD NOT FIND A VALID OPERATING SYSTEM.
Any help would be greatly appreciated.

skullymullins said:
I rooted my Unlocked xl 2 using a method I found online. Used it a couple of days rooted and decided to go back to stock so....
I downloaded the factory image, ran the flash -all.bat and everything was good. Next I went back to my boot loader to re lock it, ran the command , selected yes.
After I hit yes to re lock the boot loader I got the following error. COULD NOT FIND A VALID OPERATING SYSTEM.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
1. fastboot flashing unlock
2. fastboot flashing unlock_critical
3. Reboot the phone if prompted
4. flash firmware using flash-all script again. Read the results and watch for errors that might explain the problem and which partition (a or b) it is flashing to.
5. fastboot --set-active=b (or a. Just set it to whichever partition the script was not flashing to.)
6. flash firmware with flash-all script again to flash the alternate partition

Ok Thanks Ill give that a try..

skullymullins said:
Ok Thanks Ill give that a try..
Click to expand...
Click to collapse
And don't relock until you are 100 percent certain it is ok. I suggest waiting until you get the next update to be sure. Actually I suggest not relocking it but if you insist then wait and make sure the next update goes ok.

TonikJDK said:
And don't relock until you are 100 percent certain it is ok. I suggest waiting until you get the next update to be sure. Actually I suggest not relocking it but if you insist then wait and make sure the next update goes ok.
Click to expand...
Click to collapse
When I tried the command . fastboot --set-active b i got the unknown command error

skullymullins said:
When I tried the command . fastboot --set-active b i got the unknown command error
Click to expand...
Click to collapse
You rooted your phone with a method you found online??? Hmmmm, that's curious. Hope that didn't do any internal damage. Anyways, when your in fastboot mode, and type in "fastboot devices" do you get your device ID number??

TheSt33v said:
1. fastboot flashing unlock
2. fastboot flashing unlock_critical
3. Reboot the phone if prompted
4. flash firmware using flash-all script again. Read the results and watch for errors that might explain the problem and which partition (a or b) it is flashing to.
5. fastboot --set-active b (or a. Just set it to whichever partition the script was not flashing to.)
6. flash firmware with flash-all script again to flash the alternate partition
Click to expand...
Click to collapse
I told one person that was having trouble also to instead of doing step 4 instead download Deuces bootloop kit and allow it to flash your phone for you because I noticed a few people were not flashing in fastboot properly the pixel is different from the prior phones they are used to there are many more Sig files that were not all getting flashed thoroughly causing issues. Deuces kit does it all perfect and it's pretty easy to set up and go

skullymullins said:
When I tried the command . fastboot --set-active b i got the unknown command error
Click to expand...
Click to collapse
Maybe that command works also. I use
Fastboot --set-active=b

skullymullins said:
When I tried the command . fastboot --set-active b i got the unknown command error
Click to expand...
Click to collapse
Sorry, the previous post is right. You need an = in there.

Help needed to Unbrick

Hi,
I own an Honor 7X (BND-L21) European variant. I was on Oreo Beta firmware BND-L21C432B302(432log) version.
I wanted to update to stable oreo firmware following this guide by @mrmazak
But unfortunately while in twrp, it wasn't responding to my volume down button click & auto aborted (as stated in the linked thread)
So I reboot the phone & suddenly it went into stock recovery & started to update. But at 5% it failed & from then, I'm unable to flash anything.
Tried rebooting & booting into TWRP, but TWRP doesn't exist anymore & boots into erecovery or stock recovery.
Phone doesn't goes beyond Huawei logo.
Tried flashing Oreo TWRP but it fails. tried flashing stock OREO recovery from update.zip, fails.
Tried both fastboot flash recovery & fastboot flash recovery-ramdisk command
My device detail is as below
fastboot oem get-product-model : BND-L21
fastboot getvar vendorcountry : hw/eu
fastboot oem get-build-number : BND-L21 8.0.0.302(C432log)
fastboot getvar rescue_enter_recovery : getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION : BND-L21C432B102CUSTC432D001
The firmware I tried was BND-L21C432B330CUSTC432D2
Any kind of help is appreciated.
Cheers.

mumith3 said:
Hi,
I own an Honor 7X (BND-L21) European variant. I was on Oreo Beta firmware BND-L21C432B302(432log) version.
I wanted to update to stable oreo firmware following this guide by @mrmazak
But unfortunately while in twrp, it wasn't responding to my volume down button click & auto aborted (as stated in the linked thread)
So I reboot the phone & suddenly it went into stock recovery & started to update. But at 5% it failed & from then, I'm unable to flash anything.
Tried rebooting & booting into TWRP, but TWRP doesn't exist anymore & boots into erecovery or stock recovery.
Phone doesn't goes beyond Huawei logo.
Tried flashing Oreo TWRP but it fails. tried flashing stock OREO recovery from update.zip, fails.
Tried both fastboot flash recovery & fastboot flash recovery-ramdisk command
My device detail is as below
fastboot oem get-product-model : BND-L21
fastboot getvar vendorcountry : hw/eu
fastboot oem get-build-number : BND-L21 8.0.0.302(C432log)
fastboot getvar rescue_enter_recovery : getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION : BND-L21C432B102CUSTC432D001
The firmware I tried was BND-L21C432B330CUSTC432D2
Any kind of help is appreciated.
Cheers.
Click to expand...
Click to collapse
Re failing at 5% suggests to me that one of the three file was not found.
Not able to fastboot flash never happened to me.
The not booting happened to me after flashing different region firmware. And factory resetting with recovery including format cache got it to boot.
Is you bootloader unlocked. Still?

mrmazak said:
Re failing at 5% suggests to me that one of the three files was not found.
Not able to fastboot flash never happened to me.
The not booting happened to me after flashing different region firmware. And factory resetting with recovery including format cache got it to boot.
Is your bootloader unlocked? Still?
Click to expand...
Click to collapse
all 3 files were perfectly there in "HWOTA8" folder in external SD
Bootloader & FRP both unlocked still.
Firmware region is same. I matched it thoroughly.
I don't know why fastboot can't flash recovery anymore
right now, I tried to fastboot flash system with aosp GSI img. it worked... then again extracted system.img from update.app .... again bootloop.
but still the same problem with fastboot flash recovery.... can't flash recovery.
Any advice?

mumith3 said:
all 3 files were perfectly there in "HWOTA8" folder in external SD
Bootloader & FRP both unlocked still.
Firmware region is same. I matched it thoroughly.
I don't know why fastboot can't flash recovery anymore
right now, I tried to fastboot flash system with aosp GSI img. it worked... then again extracted system.img from update.app .... again bootloop.
but still the same problem with fastboot flash recovery.... can't flash recovery.
Any advice?
Click to expand...
Click to collapse
What command Are you using to flash recovery?
Code:
fastboot flash recovery_ramdisk twrp-filename.img

mrmazak said:
What command Are you using to flash recovery?
Code:
fastboot flash recovery_ramdisk twrp-filename.img
Click to expand...
Click to collapse
Sir, I tried with the RECOVERY_RAMDIS.img in your AFH .... It worked !!!! how???
Edit
Funnily, fastboot flash recovery-ramdisk works in powershell.... doesn't work with CMD..... !!!! What in the world is happening?
edit
Sir @mrmazak can not boot into fastboot anymore.... doesn't get past after stock recovery !!! any advices?

mumith3 said:
Sir, I tried with the RECOVERY_RAMDIS.img in your AFH .... It worked !!!! how???
Edit
Funnily, fastboot flash recovery-ramdisk works in powershell.... doesn't work with CMD..... !!!! What in the world is happening?
edit
Sir @mrmazak can not boot into fastboot anymore.... doesn't get past after stock recovery !!! any advices?
Click to expand...
Click to collapse
Really don't know what you are doing, it is not recovery-ramdisk It is recovery_ramdisk
Under score not dash

mrmazak said:
Really don't know what you are doing, it is not recovery-ramdisk It is recovery_ramdisk
Under score not dash
Click to expand...
Click to collapse
it was a typo in forum.... !!! :cyclops: got into fastboot.
Sir, when I install hwota8_update-auto-rename, I need to press volume down at the end of the script, roght? but my volume down button press is not being detected.... should I try the commands from directly inside TWRP terminal?
& if you don't mind, can I have your whatsapp/telegram nmbr in PM? I'm really trying to fix my phone :crying:
Current situation,
TWRP installed,
Fastboot accessible
doesn't go past huawei splash logo/twrp
Edit
Manual Flashing through TWRP terminal worked.... currently on OREO Stable

mumith3 said:
it was a typo in forum.... !!! :cyclops: got into fastboot.
Sir, when I install hwota8_update-auto-rename, I need to press volume down at the end of the script, roght? but my volume down button press is not being detected.... should I try the commands from directly inside TWRP terminal?
& if you don't mind, can I have your whatsapp/telegram nmbr in PM? I'm really trying to fix my phone :crying:
Current situation,
TWRP installed,
Fastboot accessible
doesn't go past huawei splash logo/twrp
Edit
Manual Flashing through TWRP terminal worked.... currently on OREO Stable
Click to expand...
Click to collapse
I need to look at that code I'm using, that looks for the buttons. It works sometimes and not others.
Manual reboot to recovery should have worked also. Bit good that you are back going again
edit:
updated the hwota8_update-auto-rename.zip , removed the volume button check and leave it for the user to do a reboot recovery from menu. (made this way , to be able to cancel the update for whatever reason , might arise.)

mrmazak said:
I need to look at that code I'm using, that looks for the buttons. It works sometimes and not others.
Manual reboot to recovery should have worked also. Bit good that you are back going again
edit:
updated the hwota8_update-auto-rename.zip , removed the volume button check and leave it for the user to do a reboot recovery from menu. (made this way , to be able to cancel the update for whatever reason , might arise.)
Click to expand...
Click to collapse
Thanks for all the help Sir ?
P.S. Oreo stable is pretty damn good so far.

asus 5z stucked in fastboot loop

i tried to install twrp in asus 5z through commands then i flashed the wrong active slot or may be both.
now my mobile is stuck at fastboot , i tried many tools and commands, it is getting out i means turns off and turns on the screen then the next second itself it shows fastboot
nothing is working i tried power botton and vol+ and vol- plus power and all the combinations mobile turning off and turning on into fastboot dirctly
what should i do ?????

dharmateja439 said:
i tried to install twrp in asus 5z through commands then i flashed the wrong active slot or may be both.
now my mobile is stuck at fastboot , i tried many tools and commands, it is getting out i means turns off and turns on the screen then the next second itself it shows fastboot
nothing is working i tried power botton and vol+ and vol- plus power and all the combinations mobile turning off and turning on into fastboot dirctly
what should i do ?????
Click to expand...
Click to collapse
1. Flash original boot.img, or
2. flash full original ROM, or
3. factory reset.

dharmateja439 said:
i tried to install twrp in asus 5z through commands then i flashed the wrong active slot or may be both.
now my mobile is stuck at fastboot , i tried many tools and commands, it is getting out i means turns off and turns on the screen then the next second itself it shows fastboot
nothing is working i tried power botton and vol+ and vol- plus power and all the combinations mobile turning off and turning on into fastboot dirctly
what should i do ?????
Click to expand...
Click to collapse
1. Flash the boot.img
2. Or flash FB ROM from here:
https://dlcdnets.asus.com/pub/ASUS/...KL-90.11.162.58-MR5-user_20190424-release.zip

i tried to flash this by command fastboot flash boot filename.zip
but it saysinvalid sparse file format at header magic
and some more errors says mmultiple blocks
and failed remote flashing partition

dharmateja439 said:
i tried to flash this by command fastboot flash boot filename.zip
but it saysinvalid sparse file format at header magic
and some more errors says mmultiple blocks
and failed remote flashing partition
Click to expand...
Click to collapse
You cannot flash .zip file. Command shoulf be:
fastboot flash boot boot.img (in case the boot.img file is located in the same folder as fastboot.exe).
Do not forget to flash it to the right slot A/B, where your system is currently located.

dharmateja439 said:
i tried to flash this by command fastboot flash boot filename.zip
but it saysinvalid sparse file format at header magic
and some more errors says mmultiple blocks
and failed remote flashing partition
Click to expand...
Click to collapse
You don't have to flash it like that.
1. Extract the zip.
2. Open the extracted folder.
3. Put your phone in bootloader (fastboot mode).
4. Double click on 'flash_ALL.bat' file.
Flashing will start.
---------- Post added at 08:51 PM ---------- Previous post was at 08:51 PM ----------
pvscz said:
You cannot flash .zip file. Command shoulf be:
fastboot flash boot boot.img (in case the boot.img file is located in the same folder as fastboot.exe).
Do not forget to flash it to the right slot A/B, where your system is currently located.
Click to expand...
Click to collapse
No. It's an FB ROM, you don't have to select any partition. It will do everything on its own.

Ok, I thought you are flashing only boot... Anyway, hamzain just replied you correctly.

hamzain said:
You don't have to flash it like that.
1. Extract the zip.
2. Open the extracted folder.
3. Put your phone in bootloader (fastboot mode).
4. Double click on 'flash_ALL.bat' file.
Flashing will start.
thank you so much hamzain
you are awsme
i have been searcing for solution since 2 days ur trick worked
my mobie is alive
thanks again
Click to expand...
Click to collapse

dharmateja439 said:
hamzain said:
You don't have to flash it like that.
1. Extract the zip.
2. Open the extracted folder.
3. Put your phone in bootloader (fastboot mode).
4. Double click on 'flash_ALL.bat' file.
Flashing will start.
thank you so much hamzain
you are awsme
i have been searcing for solution since 2 days ur trick worked
my mobie is alive
thanks again
Click to expand...
Click to collapse
Nice. Don't just say thanks, click thanks
Click to expand...
Click to collapse

wth is wrong with me/asus/xda
why in the world am running CSC ROM, should i stop looking for answer and better move on to my old life?

I'm Stuck in fast boot loop while installing TWRP . your kind help will highly appreciate.

977Hemant said:
I'm Stuck in fast boot loop while installing TWRP . your kind help will highly appreciate.
Click to expand...
Click to collapse
Furthermore, my device is not connecting to PC as well.. Please don't let me sink .
#HELP#HELP

I fix your phone in 1 day

Please Help [Stuck on boot logo, can't boot to recovery or ROM]

Stuck on boot logo !!!!! :crying:
Can't :
1. Can't boot to ROM (as doing so just stays on boot logo)
2. Can't boot into recovery (as doing this gets me to either black screen or just boots back to the boot logo)
Can :
1. Can enter bootloader
2. Can able to use fastboot commands
Tried:
1. flashing stock ROM several times,
2. flashing stock recovery
3. flashing twrp recovery
:crying:

Check my guide. It might come handy.
https://forum.xda-developers.com/le...-lenovo-p2-t4006405/post80955105#post80955105

alirazaagha said:
Check my guide. It might come handy.
https://forum.xda-developers.com/le...-lenovo-p2-t4006405/post80955105#post80955105
Click to expand...
Click to collapse
Friend thanks for the reply but your link just says "Duplicate thread. "

hackiee said:
Friend thanks for the reply but your link just says "Duplicate thread. "
Click to expand...
Click to collapse
Yes, it was. Check this one.
https://forum.xda-developers.com/lenovo-p2/how-to/guide-unbrick-unlocked-lenovo-p2-t4006401

alirazaagha said:
Yes, it was. Check this one.
https://forum.xda-developers.com/lenovo-p2/how-to/guide-unbrick-unlocked-lenovo-p2-t4006401
Click to expand...
Click to collapse
Thanks for your post friend, but, your guide doesn't fulfill my situation.
As, I am stuck on bootliader or boot logo.
I have flashed all firmwares s048,s233,s244,s51 through fastboot but none of them able to get me out of it.
Even tried flashing various recoveries both stock and twrp but neither of them helped
If, anyhow I can be able to enter into TWRP. It will solve the problem. But, I don't know nothing seems to work.
Even tried corrupting the bootloader and then flashing blankflash, but that too didn't able to get me out of the bootlogo.
Please help ?

alirazaagha said:
Yes, it was. Check this one.
https://forum.xda-developers.com/lenovo-p2/how-to/guide-unbrick-unlocked-lenovo-p2-t4006401
Click to expand...
Click to collapse
Hey, can you please do 1 thing.
Can you provide an image of the bootloader mode of your lenovo p2, if, there's something to lookup idk
I am attaching image of my bootloader, if you can look into it.
Thanks

hackiee said:
Hey, can you please do 1 thing.
Can you provide an image of the bootloader mode of your lenovo p2, if, there's something to lookup idk
I am attaching image of my bootloader, if you can look into it.
Thanks
Click to expand...
Click to collapse
It's alright.

alirazaagha said:
It's alright.
Click to expand...
Click to collapse
nothing strange ? Ok thanks

hackiee said:
nothing strange ? Ok thanks
Click to expand...
Click to collapse
Yep. Go ahead. You can try S244 firmware to try and boot your phone. If it boots then update accordingly as I mentioned in my guide.

alirazaagha said:
Yep. Go ahead. You can try S244 firmware to try and boot your phone. If it boots then update accordingly as I mentioned in my guide.
Click to expand...
Click to collapse
Still no luck! :crying: flashed S244 several times but nothing.
Can you confirm one more thing.
When I give
"Fastboot format system" I get :
"Formatting is not supported for file system with type 'raw'."
screenshot attached. Please check

hackiee said:
Still no luck! :crying: flashed S244 several times but nothing.
Can you confirm one more thing.
When I give
"Fastboot format system" I get :
"Formatting is not supported for file system with type 'raw'."
screenshot attached. Please check
Click to expand...
Click to collapse
OK so you are not following my guide Check .txt file attached in that guide and if you are still unsure then ask me.

alirazaagha said:
OK so you are not following my guide Check .txt file attached in that guide and if you are still unsure then ask me.
Click to expand...
Click to collapse
I have checked the text file of your guide, and they are the same instructions which I have been following since start. :silly:
The "fastboot format system" is a command which I used to do on my Moto G, and was able to format system successfully.
But, I don't remember if it used to work on P2 or not , that's why I asked you. If, you can use that command to check the output on your device.
Thanks

hackiee said:
I have checked the text file of your guide, and they are the same instructions which I have been following since start. :silly:
The "fastboot format system" is a command which I used to do on my Moto G, and was able to format system successfully.
But, I don't remember if it used to work on P2 or not , that's why I asked you. If, you can use that command to check the output on your device.
Thanks
Click to expand...
Click to collapse
Hmmm so you haven't read .txt file carefully. Command is:
Fastboot ERASE system
See the difference now? :silly:
Please, discuss it on that thread if need so others could also benefit from it.

alirazaagha said:
Hmmm so you haven't read .txt file carefully. Command is:
Fastboot ERASE system.
Click to expand...
Click to collapse
OMG, yes brother, I already know the command, and I have used it several times, the fastboot ERASE command, but, as mentioned several timesin the past, it is not solving my problem.
As, I am still not able to enter into any recovery(neither stock nor twrp), and not able to boot and OS.
That's why, I wanna try "Fastboot format system" command.
If, somehow that solves my problem

hackiee said:
OMG, yes brother, I already know the command, and I have used it several times, the fastboot ERASE command, but, as mentioned several timesin the past, it is not solving my problem.
As, I am still not able to enter into any recovery(neither stock nor twrp), and not able to boot and OS.
That's why, I wanna try "Fastboot format system" command.
If, somehow that solves my problem
Click to expand...
Click to collapse
OK. I though that you only tried Format command not erase. You should skip this command and do the whole process. I have added this command so that previous system files are erased. But, I booted my phone without using this command first time. Second time, I tried to see if I can do it all in a single process then I added this command and it worked without any issues and all the process went smooth and phone booted like a new one.
Try all commands but skip erase system command.

stuck on logo , have access to fastboot only
My phone stuck on logo when i open it or when i insert charger
when i try to open recovery(volume up + down) it turned off and i can't open recovery by any way
i can access fastboot
i tried your instruction and Lenovo+P2+UnBrick+OneTeam-EypCnn and all other fastboot roms
i tried install Twrp and stock recovery
i tried blankflash
that didn't help ,i can only access fastboot
what is your recommendation ? it's a hardware issue ?

DrGhost001 said:
stuck on logo , have access to fastboot only
My phone stuck on logo when i open it or when i insert charger
when i try to open recovery(volume up + down) it turned off and i can't open recovery by any way
i can access fastboot
i tried your instruction and Lenovo+P2+UnBrick+OneTeam-EypCnn and all other fastboot roms
i tried install Twrp and stock recovery
i tried blankflash
that didn't help ,i can only access fastboot
what is your recommendation ? it's a hardware issue ?
Click to expand...
Click to collapse
Did you find any solution?

Same issue here, I guess it's a hardware issue: SSD is damaged ?

fastboot erase system
fastboot format:ext4 system
Maybe related to the file system ?

i have the same probelm, do you guys find any solution ?

Bricked device, can't get into EDL mode

Good night.
I have been using for a few days the YAAP custom rom for android 11 on my 7T, and it's been great. But I wanted to root it for some customizations and tried to flash magisk through mauronofrio's unnoficial TWRP. After trying to flash through it, my phone bricked. I can't get into fastbootd mode and the
HTML:
fastboot getvar is-userspace
command outputs "no", so I couldn't re-flash YAAP normally. I tried using the MSM tool for the 7T but I was also not able to boot into EDL mode. When I try to boot into it through the vol up/down mode, it reboots into bootloader again, and the
HTML:
fastboot oem edl
command returns FAILED (remote: unknown command).
I can flash twrp, but when I try to flash the YAAP zip, it shows me an error.
It shows signs of life, as it gets caught into the OOS boot animation loop, so I know there is a way around it, but I am having trouble figuring out how.
Would anyone here know how to circulate this issue? Or has been through something like this?

Shiro744760 said:
Good night.
I have been using for a few days the YAAP custom rom for android 11 on my 7T, and it's been great. But I wanted to root it for some customizations and tried to flash magisk through mauronofrio's unnoficial TWRP. After trying to flash through it, my phone bricked. I can't get into fastbootd mode and the
HTML:
fastboot getvar is-userspace
command outputs "no", so I couldn't re-flash YAAP normally. I tried using the MSM tool for the 7T but I was also not able to boot into EDL mode. When I try to boot into it through the vol up/down mode, it reboots into bootloader again, and the
HTML:
fastboot oem edl
command returns FAILED (remote: unknown command).
I can flash twrp, but when I try to flash the YAAP zip, it shows me an error.
It shows signs of life, as it gets caught into the OOS boot animation loop, so I know there is a way around it, but I am having trouble figuring out how.
Would anyone here know how to circulate this issue? Or has been through something like this?
Click to expand...
Click to collapse
If you are getting as far as the boot logo then you might be able to format data and try it
can't you reboot to EDL from fastboot?
fastboot reboot EDL ?
You said you can't use the MSM tool. Have you tried the regular all-in-one tool here on the forum?
Try fastboot boot twrp.img, format data and reflash the custom rom?
I'm just throwing ideas out here they may not be the best lol

redemptionx11 said:
If you are getting as far as the boot logo then you might be able to format data and try it
can't you reboot to EDL from fastboot?
fastboot reboot EDL ?
Click to expand...
Click to collapse
Can't. I have tried it before. fastboot reboot edl says the command is unknown, and the existing command (fastboot reboot emergency) throws me back to the bootloader.
The logo got weird. It shows up for a second after turning on and then the bootloader shows up.
redemptionx11 said:
You said you can't use the MSM tool. Have you tried the regular all-in-one tool here on the forum?
Try fastboot boot twrp.img, format data and reflash the custom rom?
I'm just throwing ideas out here they may not be the best lol
Click to expand...
Click to collapse
I haven't tried the all-in-one tool yet, but I don't know which one is it yet lol.
As for twrp this is the log I get:
HTML:
PS D:\Documentos\ADB> fastboot boot .\recovery-oneplus7t-3.4.2-10.0-b26.img
downloading 'boot.img'...
OKAY [ 2.318s]
booting...
FAILED (remote: Failed to load/authenticate boot image: Load Error)
finished. total time: 2.337s

I'm going to assume you did fastboot reboot fastboot before you tried yes?
I'd go try the all in one. There's a thread for it named "all in one" or something.
The tool might have an option to reboot to EDL I can't remember but I've fixed several soft bricks using it.

redemptionx11 said:
I'm going to assume you did fastboot reboot fastboot before you tried yes?
Click to expand...
Click to collapse
Yes I did. Powershell says it does not exist and list all other commands
redemptionx11 said:
I'd go try the all in one. There's a thread for it named "all in one" or something.
The tool might have an option to reboot to EDL I can't remember but I've fixed several soft bricks using it.
Click to expand...
Click to collapse
I will look into it

The all in one worked for getting into the EDL mode. And for the rest of the process, @SkippRunning really helped a lot. Kudos for him for helping out lost souls and bricked devices!

Shiro744760 said:
The all in one worked for getting into the EDL mode. And for the rest of the process, @SkippRunning really helped a lot. Kudos for him for helping out lost souls and bricked devices!
Click to expand...
Click to collapse
ayyy well done man. Good to see you got it going

maybe you can try changing the slot from a to b or opposite