Hello,
at first i am sorry for my englisch. I will give my best to write without any mistakes.
I have a big problem. I unlocked the bootloader on my LG g4 than I am gonna installed TRWP. Suddenly i couldnt boot my phone again.
I see only the branding logo. I ve tried to make a hardreset with the power and volume down buttom, but the phones is stuck at the branding logo.
I have also an access to downloading mode. I also tried to install a other firmware, but with LG Flash tool its not possilbe. It gives me during the installation an error. "Upgrade stopped due to an error".
Have i any possiblities to unbrick my phone ?? My currently software was Android 6 815.20A. Please help me to find out any solutions.
thanks
michael2412 said:
Hello,
at first i am sorry for my englisch. I will give my best to write without any mistakes.
I have a big problem. I unlocked the bootloader on my LG g4 than I am gonna installed TRWP. Suddenly i couldnt boot my phone again.
I see only the branding logo. I ve tried to make a hardreset with the power and volume down buttom, but the phones is stuck at the branding logo.
I have also an access to downloading mode. I also tried to install a other firmware, but with LG Flash tool its not possilbe. It gives me during the installation an error. "Upgrade stopped due to an error".
Have i any possiblities to unbrick my phone ?? My currently software was Android 6 815.20A. Please help me to find out any solutions.
thanks
Click to expand...
Click to collapse
Check if you can use LGUP while in download mode.
thanks
Thank you very much. I resolved the problem with LGUP.
Hi everyone. So a few days ago I was trying to install some new roms on my G3. Being the sped I am, I installed the D855 version of the rom rather than the d851. My phone is now hard bricked. I followed this guide http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 and could do a couple of things. My phone actually connects via qualcomm mode but that is not the problem. When I try do the EMMC test it does not detect my phone. I get the message No response from the device. Check PMIC first andif still boot problem, replace AP or device not found in dload trying flash programmer. This is a problem I can't seem to fix. Anyone have any help?
Andrescelano said:
Hi everyone. So a few days ago I was trying to install some new roms on my G3. Being the sped I am, I installed the D855 version of the rom rather than the d851. My phone is now hard bricked. I followed this guide http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 and could do a couple of things. My phone actually connects via qualcomm mode but that is not the problem. When I try do the EMMC test it does not detect my phone. I get the message No response from the device. Check PMIC first andif still boot problem, replace AP or device not found in dload trying flash programmer. This is a problem I can't seem to fix. Anyone have any help?
Click to expand...
Click to collapse
Hmmm.... You have a hard brick just like i do. Join the club. http://forum.xda-developers.com/tmo...-d851-hard-brick-qualcomm-9008-mode-t3319504/
Hi,
So today suddenly my phone restarted and after that it was stuck on the micromax logo, I coudnt get into recovery either. So I tried to flash the stock kitkat rom using sp tools, it did manage to flash it the first time but the phone after that wont start at all, nothing not even the charging screen.
Is it bricked for good? I tried to flash it again but if I choose firmware upgrade or download+firmware upgrade in sp tools I get the pmt info error. Is there any way to get the phone back to a working state? Any help would be much apprecited.
Note: I did look through the old post on the similar topic where the guy managed to solve the problem by using a latest version of sp tools, Im already using the latest version , no dice.
Did you get anywhere with this to unbrick the device as I have similar with a GDP XP and it wont now boot or show charge its just dead!
Any help on fixing this would be great as we cant be alone with this. ATB
Redmi Note 8 Pro Global 128gb 6gb
Here's my story,
I was using Android 10 with TWRP before and then I bricked my phone by installing some magisk module and was stuck in bootloop. I was going to re-flash A10 global fastboot rom but I accidentally installed A9 instead and thus, my phone was hard bricked. Dead screen and only led notification light is on.
Here are the steps on how to unbrick your phone. (Not 100% sure if it works but we've got nothing to lose since our phone is already hard bricked.)
1. Try to install any A9 stock rom on your phone through "flash_all.bat" inside your A9 stock rom and wait for it to finish or at least long enough when you feel like it's stuck. (https://www.youtube.com/watch?v=cn5F12ixLB8)
You can download stock roms here (https://mirom.ezbox.idv.tw/en/phone/begonia/)
2. Assuming you have installed most of A9 stock rom including preloader, try to flash "preloader_begonia.bin" and "lk.img" found here (https://forum.xda-developers.com/redmi-note-8-pro/how-to/guide-redmi-note-8-pro-megathread-t4056527) and follow instructions on how to flash both files.
3. Download and install MiFlash Pro (https://mega.nz/folder/xZtzjRQI#p24N5i5Xi1S_KXPGK4Hk4w)
4. (https://www.cyanogenmods.org/forums/topic/how-to-unbrick-redmi-note-8-pro/) Follow this tutorial starting from step 3 and wait for around 5 mins until "Download OK" shows up and then reboot your phone.
PS: If your having a hard time trying to detect your phone on your pc, don't connect your phone yet. Click the "download" button on SP Flashtool first and then connect your phone. Press all 3 buttons (Vol+, Vol-, Power button) until your pc detects your phone and SP Flashtool will automatically flash your device.
5. DONE!
Tell me if it works or not so that I can try to help each and every one of you. Cheers!
HEllo could help my on teamviewer?
seser111 said:
HEllo could help my on teamviewer?
Click to expand...
Click to collapse
Hi! Could you tell me how you bricked your phone? is it soft bricked or hard bricked?
djgilquirino said:
Hi! Could you tell me how you bricked your phone? is it soft bricked or hard bricked?
Click to expand...
Click to collapse
It's hard bricked. I tried sp flash tool it requires authorized account.
djgilquirino said:
Redmi Note 8 Pro Global 128gb 6gb
Here's my story,
I was using Android 10 with TWRP before and then I bricked my phone by installing some magisk module and was stuck in bootloop. I was going to re-flash A10 global fastboot rom but I accidentally installed A9 instead and thus, my phone was hard bricked. Dead screen and only led notification light is on.
Here are the steps on how to unbrick your phone. (Not 100% sure if it works but we've got nothing to lose since our phone is already hard bricked.)
1. Try to install any A9 stock rom on your phone through "flash_all.bat" inside your A9 stock rom and wait for it to finish or at least long enough when you feel like it's stuck. (
)
You can download stock roms here (https://mirom.ezbox.idv.tw/en/phone/begonia/)
2. Assuming you have installed most of A9 stock rom including preloader, try to flash "preloader_begonia.bin" and "lk.img" found here (https://forum.xda-developers.com/redmi-note-8-pro/how-to/guide-redmi-note-8-pro-megathread-t4056527) and follow instructions on how to flash both files.
3. Download and install MiFlash Pro (https://mega.nz/folder/xZtzjRQI#p24N5i5Xi1S_KXPGK4Hk4w)
4. (https://www.cyanogenmods.org/forums/topic/how-to-unbrick-redmi-note-8-pro/) Follow this tutorial starting from step 3 and wait for around 5 mins until "Download OK" shows up and then reboot your phone.
PS: If your having a hard time trying to detect your phone on your pc, don't connect your phone yet. Click the "download" button on SP Flashtool first and then connect your phone. Press all 3 buttons (Vol+, Vol-, Power button) until your pc detects your phone and SP Flashtool will automatically flash your device.
5. DONE!
Tell me if it works or not so that I can try to help each and every one of you. Cheers!
Click to expand...
Click to collapse
How can you even brick if you rollback to older Android version accidentally via fastboot ? This phone doesn't even have ARB
Anyway, it's possible to unbrick since you able to flash factory preloader and lk
TheMalachite said:
How can you even brick if you rollback to older Android version accidentally via fastboot ? This phone doesn't even have ARB
Anyway, it's possible to unbrick since you able to flash factory preloader and lk
Click to expand...
Click to collapse
That's the problem. I didn't know why I bricked my phone while flashing A9. It just didn't boot after rebooting my phone. I think as long as you flashed A9, you can proceed to flash the preloader and lk and unbrick it.
Same pproblem
djgilquirino said:
Redmi Note 8 Pro Global 128gb 6gb
Here's my story,
I was using Android 10 with TWRP before and then I bricked my phone by installing some magisk module and was stuck in bootloop. I was going to re-flash A10 global fastboot rom but I accidentally installed A9 instead and thus, my phone was hard bricked. Dead screen and only led notification light is on.
Here are the steps on how to unbrick your phone. (Not 100% sure if it works but we've got nothing to lose since our phone is already hard bricked.)
1. Try to install any A9 stock rom on your phone through "flash_all.bat" inside your A9 stock rom and wait for it to finish or at least long enough when you feel like it's stuck. (https://www.youtube.com/watch?v=cn5F12ixLB8)
You can download stock roms here (https://mirom.ezbox.idv.tw/en/phone/begonia/)
2. Assuming you have installed most of A9 stock rom including preloader, try to flash "preloader_begonia.bin" and "lk.img" found here (https://forum.xda-developers.com/redmi-note-8-pro/how-to/guide-redmi-note-8-pro-megathread-t4056527) and follow instructions on how to flash both files.
3. Download and install MiFlash Pro (https://mega.nz/folder/xZtzjRQI#p24N5i5Xi1S_KXPGK4Hk4w)
4. (https://www.cyanogenmods.org/forums/topic/how-to-unbrick-redmi-note-8-pro/) Follow this tutorial starting from step 3 and wait for around 5 mins until "Download OK" shows up and then reboot your phone.
PS: If your having a hard time trying to detect your phone on your pc, don't connect your phone yet. Click the "download" button on SP Flashtool first and then connect your phone. Press all 3 buttons (Vol+, Vol-, Power button) until your pc detects your phone and SP Flashtool will automatically flash your device.
5. DONE!
Tell me if it works or not so that I can try to help each and every one of you. Cheers!
Click to expand...
Click to collapse
I have same problem like you. How did you flash when your RM8P is hard brick? I try same things like youtube, but my cmd windows just close immediately. And if I move fastboot tool in the rom folder, cmd window didn't close but doing nothing. How did you do that?
My RN8P don't have recovery or fastboot.
thanks
thank you very much, my phone is resurrected. ?❤
OP's phone was softbricked(as they still had access to fastboot) and is now claiming that a preemptive measure can unbrick a hardbricked phone
Benedict Cumberbatch said:
OP's phone was softbricked(as they still had access to fastboot) and is now claiming that a preemptive measure can unbrick a hardbricked phone
Click to expand...
Click to collapse
Well I pointed out that it was just a possible way and not an absolute way on unbricking my phone. And I guess you're right about my phone being softbricked and I apologize for that mistake. Cheers
djgilquirino said:
Redmi Note 8 Pro Global 128gb 6gb
Here's my story,
I was using Android 10 with TWRP before and then I bricked my phone by installing some magisk module and was stuck in bootloop. I was going to re-flash A10 global fastboot rom but I accidentally installed A9 instead and thus, my phone was hard bricked. Dead screen and only led notification light is on.
Here are the steps on how to unbrick your phone. (Not 100% sure if it works but we've got nothing to lose since our phone is already hard bricked.)
1. Try to install any A9 stock rom on your phone through "flash_all.bat" inside your A9 stock rom and wait for it to finish or at least long enough when you feel like it's stuck. (https://www.youtube.com/watch?v=cn5F12ixLB8)
You can download stock roms here (https://mirom.ezbox.idv.tw/en/phone/begonia/)
2. Assuming you have installed most of A9 stock rom including preloader, try to flash "preloader_begonia.bin" and "lk.img" found here (https://forum.xda-developers.com/redmi-note-8-pro/how-to/guide-redmi-note-8-pro-megathread-t4056527) and follow instructions on how to flash both files.
3. Download and install MiFlash Pro (https://mega.nz/folder/xZtzjRQI#p24N5i5Xi1S_KXPGK4Hk4w)
4. (https://www.cyanogenmods.org/forums/topic/how-to-unbrick-redmi-note-8-pro/) Follow this tutorial starting from step 3 and wait for around 5 mins until "Download OK" shows up and then reboot your phone.
PS: If your having a hard time trying to detect your phone on your pc, don't connect your phone yet. Click the "download" button on SP Flashtool first and then connect your phone. Press all 3 buttons (Vol+, Vol-, Power button) until your pc detects your phone and SP Flashtool will automatically flash your device.
5. DONE!
Tell me if it works or not so that I can try to help each and every one of you. Cheers!
Click to expand...
Click to collapse
In soft bricks, you can access recovery or fastboot or both, and easily flash the stock ROM, but you have mentioned above that your phone was hard bricked, there is almost no way to unbrick a hard bricked RN8P without authorized account, even if you do, its very likely it was once in a million chance that it got flashed, best way to recover a hard bricked RN8P is to not mess it up more and take it to service center right away.
Help please!!
I'm Stuck.. idk what it is.
I flashed my RN8 with Google PE using TWRP. But now I'm stuck in some sort of boot-loop where I'm neither able to access Recovery menu nor the Fast-boot page.
Help me too somehow.
Thanks if you could respond. :crying::crying:
---------- Post added at 12:50 PM ---------- Previous post was at 12:37 PM ----------
I'm Stuck.. idk what it is.
I flashed my RN8 with Google PE using TWRP. But now I'm stuck in some sort of boot-loop where I'm neither able to access Recovery menu nor the Fast-boot page.
Help me too somehow.
Thanks if you could respond
there are ways to unlock the RN8Pro, even after a hard brick. Either you buy the UFI Box and do it yourself (180 €) or you call someone who does it using the team viewer, the call was cheaper and more successful for me. I would love to share the phone number with you guys, but I think the moderators will mind ?!
there are ways to unlock the RN8Pro, even after a hard brick. Either you buy the UFI Box and do it yourself (180 €) or you call someone who does it using the team viewer, the call was cheaper and more successful for me. I would love to share the phone number with you guys, but I think the moderators will mind ?!
Hey, my redmi 4a is soft bricked, please guide me how to fix it. I'm like a noob, so i need A to Z guide
Hey my
djgilquirino said:
Redmi Note 8 Pro Global 128gb 6gb
Here's my story,
I was using Android 10 with TWRP before and then I bricked my phone by installing some magisk module and was stuck in bootloop. I was going to re-flash A10 global fastboot rom but I accidentally installed A9 instead and thus, my phone was hard bricked. Dead screen and only led notification light is on.
Here are the steps on how to unbrick your phone. (Not 100% sure if it works but we've got nothing to lose since our phone is already hard bricked.)
1. Try to install any A9 stock rom on your phone through "flash_all.bat" inside your A9 stock rom and wait for it to finish or at least long enough when you feel like it's stuck. (
)
You can download stock roms here (https://mirom.ezbox.idv.tw/en/phone/begonia/)
2. Assuming you have installed most of A9 stock rom including preloader, try to flash "preloader_begonia.bin" and "lk.img" found here (https://forum.xda-developers.com/redmi-note-8-pro/how-to/guide-redmi-note-8-pro-megathread-t4056527) and follow instructions on how to flash both files.
3. Download and install MiFlash Pro (https://mega.nz/folder/xZtzjRQI#p24N5i5Xi1S_KXPGK4Hk4w)
4. (https://www.cyanogenmods.org/forums/topic/how-to-unbrick-redmi-note-8-pro/) Follow this tutorial starting from step 3 and wait for around 5 mins until "Download OK" shows up and then reboot your phone.
PS: If your having a hard time trying to detect your phone on your pc, don't connect your phone yet. Click the "download" button on SP Flashtool first and then connect your phone. Press all 3 buttons (Vol+, Vol-, Power button) until your pc detects your phone and SP Flashtool will automatically flash your device.
5. DONE!
Tell me if it works or not so that I can try to help each and every one of you. Cheers!
Click to expand...
Click to collapse
Hey, my redmi 4a is soft brick,
Can you guide me from beginning?
megaros said:
there are ways to unlock the RN8Pro, even after a hard brick. Either you buy the UFI Box and do it yourself (180 €) or you call someone who does it using the team viewer, the call was cheaper and more successful for me. I would love to share the phone number with you guys, but I think the moderators will mind ?!
Click to expand...
Click to collapse
Would you be so kind as to maybe PM that # to me? Ive been trying to get mine unbricked for probably over a year now and havent had any luck even finding a place or person to do the unlock.... I would really appreciate it...
U mnie zadziałał ten sposób
.
namurnik said:
U mnie zadziałał ten sposób
.
Click to expand...
Click to collapse
No widze ze dobrze to wyglada , powiedz mi tylko czy miales naprawde HARDBRICK , czy tylko SOFTBRICK , ?
Well I see it looks good, just tell me if you had a really HARDBRICK or just a SOFTBRICK?
Hi everyone. My Redmi note 5 pro is not turning on, it just gets stucked at the "redmi" logo. I tried disconnecting the battery but that didn't work. Since I can enter fastboot mode I also tried to flash the fastboot miui 12 rom with Miflash but an error appears saying "error flashing partition - write protected" (my phone has bootloader already unlocked). Even in EDL mode I couldn't flash the rom since it doesn't let me authenticate in my xiaomi account and miflash gets stucked at "edl authentication". Can you help me to unbrick my phone? Thank you.
nico.fiaba1 said:
Hi everyone. My Redmi note 5 pro is not turning on, it just gets stucked at the "redmi" logo. I tried disconnecting the battery but that didn't work. Since I can enter fastboot mode I also tried to flash the fastboot miui 12 rom with Miflash but an error appears saying "error flashing partition - write protected" (my phone has bootloader already unlocked). Even in EDL mode I couldn't flash the rom since it doesn't let me authenticate in my xiaomi account and miflash gets stucked at "edl authentication". Can you help me to unbrick my phone? Thank you.
Click to expand...
Click to collapse
Same thing happened to me and another one of my friends who owned redmi note 5 pro last week. Trust me I literally tried everything, but sadly I had to go for a new phone. The xiaomi service center told me the motherboard needed to be replaced which would cost 4-5k plus the screen would need to be replaced ( if you have even a couple screen cracks ) which would cost another 2-3k. Even then I would advise to go for a new phone.
Still sus how so many RN5 pro are getting the write protected error out of nowhere in the past 15 days. I did see a couple more posts about the same here.
Hi, I have the same problem. So I did enter EDL with the two pins on the mainboard, but when I try to flash miui 12 with QFIL (Qualcomm Flash Image Loader) I get authentication error. Even if I used a patched firehose programmer file. I tried 3 different patched firehose programmer files.
Does someone have a working patched firehose programmer file for Xiaomi Redmi Note 5 Pro?
So If we do not find a working patched firehose programmer file or a xiaomi developer who share his account for 5 min then I think we are not able to solve this problem..
ralaud said:
Hi, I have the same problem. So I did enter EDL with the two pins on the mainboard, but when I try to flash miui 12 with QFIL (Qualcomm Flash Image Loader) I get authentication error. Even if I used a patched firehose programmer file. I tried 3 different patched firehose programmer files.
Does someone have a working patched firehose programmer file for Xiaomi Redmi Note 5 Pro?
So If we do not find a working patched firehose programmer file or a xiaomi developer who share his account for 5 min then I think we are not able to solve this problem..
Click to expand...
Click to collapse
Search it on XDA forum there are links and explanation how to use it.
Tip: use MI flash tool (start with version from 2018 and than newer....)
Same thing happened to me in the last week of may, I even posted a thread here for help and my phone is even stuck on fastboot logo, sadly i couldn't find any solutions. If you find any solutions please reply to this post and help a brother.
Warvid said:
Same thing happened to me in the last week of may, I even posted a thread here for help and my phone is even stuck on fastboot logo, sadly i couldn't find any solutions. If you find any solutions please reply to this post and help a brother.
Click to expand...
Click to collapse
Did you end up solving the issue? I am also facing the exact same issue.