Develop Bugs

D851 Hard Brick

I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355

Nit3H8wk said:
I cannot boot into download mode and cannot boot into twrp. The phone will not boot no matter how long i hold the power button and there is no lights. When connected to the pc it shows up as Qcom Dload. Can someone please create a debrick.img. All you need to do is flash this in twrp and send me the debrick file which should end up on your sdcard.
h ttps://www.androidfilehost.com/?fid=23578570567721355
Click to expand...
Click to collapse
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.

ThePagel said:
This has been tried before and it didnt work for the guy. Have you tried flashing a tot? It has the begining of the emmc so same outcome but you can skip all the sd card work. Good luck if the tot fails and no one steps up ill get you that debrick file just to see if your luck is better.
Click to expand...
Click to collapse
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142

Nit3H8wk said:
That was a no go i tried the older dll that bypass model checks but still fails. Guess there is a linux method that worked on the older g2 and someone with a g3 reported success so i already extracted the TOT files i need to dd over from linux.
h ttp://forum.xda-developers.com/showthread.php?t=2582142
Click to expand...
Click to collapse
Yeah that's probably your best option I have a partitions dump from the tot if yours are not working for some reason. Instead of installing twrp If I was you I would boot into download mode after and flash the tot. I did do a debrick dump with the script that I can get to you tomorrow some time and if that doesn't work tell me and I can give you a link that has 250-500mb range for the dumps from when I was helping the other guy. They weren't made with a script but with terminal emulator but they should be the same thing just bigger because the smaller dumps weren't working for him. Any way here are the partitions just in case https://www.androidfilehost.com/?fid=23622183712472493
---------- Post added at 11:59 PM ---------- Previous post was at 11:36 PM ----------
Oh and before I go to bed another thing you can try if you can send the images over but they don't seem to work. Hunt down the fastboot laf.img send that over then do the rest of the partitions via fastboot instead. Good luck!

Dead phone
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.

Nit3H8wk said:
Dead in the water. Only qpst seems to see it besides device manager (Qualcomm HS-USB QDLoader 9008). The linux method was for people who get the lg logo. I don't get anything but a black screen. Problem is i don't know enough about the qpst software to guide you on making the files. All i can say is try to make a backup using qpst and provide links. Don't know what else to do.
Click to expand...
Click to collapse
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.

ThePagel said:
In order to get you the files someone needs to reboot from the hidden menu into somthing I cant remember. Its not mini os and the d851 lacks the option in hidden menu atleast I didnt see it. The d855 hidden menu has the option and I was going to try it but he ended up sending it in before I got around to flashing the d855 rom. If you want to fix it yourself and can do without a cell phone for a few days I can try but might not be able to get you the files until sunday if it works.
Click to expand...
Click to collapse
Yeah i will have to wait then can't afford the $175 deductible right now. Thanks for the help. I don't mind waiting just hope i can find a less costly solution know what i mean?

QPST
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.

Nit3H8wk said:
So it looks like i will need a hex file and mbn partition files vs the bin files that come from the tot file. From what i read in the forums lg offers a 1 year warrenty. So i guess as a last resort i could send it in for service but i would rather try to resolve it myself.
Click to expand...
Click to collapse
Yeah I got ready to do it last night but got side tracked hopefully tonight

qpst
ThePagel said:
Yeah I got ready to do it last night but got side tracked hopefully tonight
Click to expand...
Click to collapse
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.

Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
Ill be able to tell you tomorrow afternoon if I can do it.

Nit3H8wk said:
I get paid on monday so going to ship it out to LG then. But if you are able to get the hex and mbn and secure boot files let me know i would still like to tinker a bit before that time as i know it will take a few weeks to get the phone back otherwise.
Click to expand...
Click to collapse
I cant seem to get into diag mode or field test mode so I cannot create the files for you :crying: BUT before you completely give up on fixing it take a look at this http://forum.cyanogenmod.org/topic/71825-hard-brick-to-hell-and-back-guide-to-recovery/

Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.

cesarandres_8911 said:
Qualcomm MSM8975AC
Hello
I tell them my story, mistakenly doing a ported rom stock LG G3 Marshmallow, I flashed my phone with the stock rom from Marshmallow (model D855) and after that I have bricked the phone. No download mode, no emergency mode, only is recognize for the computer as AndroiNet usb port serial.
Could please you help me to unbrick my lg g3 Phone model d851,t-mobile variant. When I plug in my Phone to computer, this is recognized as lgandroinet port serial but I have made a testpoint (open the mobile) to change the phone mode to Qualcomm HS-USB QDLoader 9008”. I have used tools like boardiag but I get the followin message: “No response from the device. Check PMIC first and if still boot problem, replace AP.” To look at this thread: http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ ... but report that it is not compatible for ATT and Tmobile variations. I currently have two virtual machines: Window xp 32 bit and Ubuntu 15.04. My client OS is 8.1 Window 64 bit.
I will be very grateful if you can help me to find a solution or can show me which is the correct way. I've been several weeks looking for a solution but I have not been able to fix my cellphone. I hope that my computer still recognizes it.
Click to expand...
Click to collapse
I just did the same thing tonight, I'll let you know if I fix it.

mxpxboi said:
I just did the same thing tonight, I'll let you know if I fix it.
Click to expand...
Click to collapse
Hello,
What is your phone and variant model? Do you have D851 model?

Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"

mxpxboi said:
Yeah D851, Black Screen and only connects as "LGE androidnet usb serial port"
Tried flashing TOT file and I get the error "Model Information Check FAIL!"
Click to expand...
Click to collapse
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.

cesarandres_8911 said:
Hello,
I will try help you, first of all you must to change the Qualqomm mode in your phone, namely change usb LGE Androinet by QDloader 9008. For this you must remove the battery from the phone, open the phone and use copper cable or tweezers and you must to touch two points on the mainboard in order to force Qualcomm mode on your phone. I have attached photos to guide you in this process. You must touch two points (without battery) and connect the usb cable to the computer. You'll hear a sound that indicates that qualcomm is active otherwise could see a battery warning on the screen. If this happens, you must disconnect the usb cable and repeat the process.
The second thing you're going to do is install the drivers appropriate for Qualcomm mode. Please follow this thread: http://www.droidsavvy.com/unbrick-qualcomm-mobiles/
This is the download link for the drivers referred to the post: http://forum.xda-developers.com/attachment.php?attachmentid=3261089&stc=1&d=1428980071
Now your computer will recognize the cellular in the indicated mode (Relink HS-USB QDloader 9008).
The next step is to use the Boarddiag tool in this post but in the root folder, place the file sbl1.mbn which is located in the folder that you extract the file TOT.
I am currently uploading a package that includes bordiag tool, sbl1.mbn file, and TOT file extracted. When the upload is complete, I could tell you what is the download link, this contain the version of Boardiag that will work in our model. Currently my phone lg g3 D851 (chip MSM8975AC) was revived.
Click to expand...
Click to collapse
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.

cesarandres_8911 said:
Good morning, please try downloading this package;
https://mega.nz/#!5lRGUZqZ!HZXaf4SP_PtuPEkg0ycdWXZP977_lBdVVqkI1P8DVtU
I'm not sure if it will work for your model, please performs the tests at your risk. Let me clarify that this is the same boarddiag version , only I try added the files needed.
Within the. 7z, there is a file called "TOT Extract", please extract it and open application BoardDiag. In the section "Target Dir" choose the path where you extracted the file.
Please inform me as it was with the tests.
Click to expand...
Click to collapse
Thank you SOOO much for your help so far.
I installed Qualcomm Drivers and touched the points and it connected.
But it says that the Drivers are blocked due to not being digitally signed.
And it's showing up in Device Manager as "Qualcomm HS-USB QDLoader 9008" with an exclamation point.
I am posting screen shots.'
You didn't have this issue?
What steps do I do in the BoardDiag exactly? Just add the directory with the file and hit start?

@mxpxboi it seems you're using windows 8/above, you have to disable driver signature, here is how to do it https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8
Sent from my LG-D801 using Tapatalk

Device will not turn on LG G3 D855 32GB

Hello everyone.
I need your help.
My Device: LG G3 D855 32GB
The device does not turn on, the only thing that appears is because when I connect the device to a PC, I see a driver installed:
RELINK HS-USB QDLoader 9008
I read guides on site here, and I'm trying to order
I downloaded the software BoardDiag 2.9
I downloaded the files to the appropriate TOT
I extracted the files by instructors on site.
I opened the program and I followed the guide and it seems to me an error
Download mode is enabled Mode,
I quickly disconnects from the computer and reconnect the computer and then the moment I am unable to do a test and the results are:
AP CHECK START = PASS
EMMC TEST START
FAILED TO OPEN PARTITION FROM EMMC
TEST ABORTED !!
I tried a lot of tutorials but I can not, it always seems the device is in Download Mode
What can I do more?
Please your help,
Eliran

If you go that way, you will need bunch of other stuff. Here is the link
http://open-freax.fr/guide-unbrick-your-lg-g3/
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.

The phone fell
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the comment
The phone fell into the vehicle.
I know the phone is always in Download Mode
The software does not let me do anything and making phone download mode
I did not try to install KDZ.
And I can not open a setup KDZ because the device does not rise and there is no open port.
I only have the port I did above.

Thanks for the help, I worked in the guide and I could not ...
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran

I need help please. What can i do
zarfati66 said:
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
Click to expand...
Click to collapse
I need help please. What can i do

The phone woke for a moment ...
zarfati66 said:
I need help please. What can i do
Click to expand...
Click to collapse
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran

relink hs-USB Qdloader 9008
ZARFATI6 said:
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
Click to expand...
Click to collapse
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????

apur32 said:
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
Click to expand...
Click to collapse
Same situation too, solutions yet?

Hey I have the same problem .
If any of you found the solution please post it here or pm me, I am stuck

Overwritten aboot.img -> G3 bricked?

Hi guys,
I made a stupid mistake:
I was overwriting aboot.img from terminal to solve "secure boot failed" error. I didn't have backcase installed and battery fell out.
Now, the phone is bricked or at least the screen remains black, no vibrating, no flashing LED.
Is there anything I can do to revive the phone?

Can you enter anything ? Download mode ?
IF nothing you have to force to qualcomm 9008 mode and use boarddiag to fix the phone

Download-mode (Vol-up while plugging in USB) does not work.
Do you think, I can unbrick it by using willcracker's method?
Is there anything I need to keep in mind? Can you give an estimation whether this approach will solve the issue?

Yes, both willcrackers and the link will fix it
If you somehow fail write here

uhm, it seems as if the archive is protected by password? Any adive on how to get hold of it or any alternative solution?
What's also a little strange: the file "androidbrick_G3_fix.7z" is above 100MB while the download of "BoardDiag v2.99a.zip" is around 7MB...
Do I need to dis-assemble the G3 to short the pins stated here?

I did the EXACT SAME THING. I guess we can be idiots together, right?
Unfortunately, boarddiag refuses to flash with some error about the AP and android_g3_fix fails for me (looks like it's working but does nothing).
If you want to try anroidbrick_g3_fix you can email the author for the password.
I'm at a loss as to what to do, I'm already in qualcomm 9008 mode with drivers...

Follow the steps on this post: http://forum.xda-developers.com/lg-g3/help/fix-marshmallow-autorec-hard-brick-t3284608
After i killed my G3 with TWRP (Autorec for LP) on MM i bring my G3 back to life.
Tip: Use a thin massive copper caple, 0,5mm, and put the other end on the top of the sim-slot for ground.
It´s easier.

Haribo68 said:
Follow the steps on this post: http://forum.xda-developers.com/lg-g3/help/fix-marshmallow-autorec-hard-brick-t3284608
After i killed my G3 with TWRP (Autorec for LP) on MM i bring my G3 back to life.
Tip: Use a thin massive copper caple, 0,5mm, and put the other end on the top of the sim-slot for ground.
It´s easier.
Click to expand...
Click to collapse
I don't have TWRP though, will it work?

Didn't seem to. I've had horrid luck with BoardDiag though...
I'm not sure if it makes any difference, but my phone is a Verizon 32GB LG G3 w/MSM8975AC that came preflashed with 35b 5.1.1 (thanks, ,verizon) and has never seemed to respond to any of the downgrade methods. Hence me playing with partitions, flashing aboot to an earleir version, and getting into this mess by failing to flash sb1.
I'm willing to pay to get this fixed, but unsure where to go or who is reputable.

I have managed to shortcircuit the pins and get my G3 to be listed as "Qualcomm HS-USB QDLoader 9008" and a corresponding COM port.
When I start the "androidbrick_G3_fix" as administrator, the tool shows that "USB Status" is "not ready". In the guide it says:
if your driver is installed you will see your port, if not, youll see “Not ready” in little green window.
Click to expand...
Click to collapse
EDIT:
I've used BoardDiag 2.99a to flash different partions according to this source extracted from *.tot file.
Now the phone (obviously) does not boot and shows "Security Error".
Trying to enter download mode seems to work though as it shows "Download Mode" followed by "Firmware Update".

MacWarrior said:
I have managed to shortcircuit the pins and get my G3 to be listed as "Qualcomm HS-USB QDLoader 9008" and a corresponding COM port.
When I start the "androidbrick_G3_fix" as administrator, the tool shows that "USB Status" is "not ready". In the guide it says:
As I've successfully installed the driver (at least the device is listed in device manager) I don't know how to proceed.
Anyone got an idea how to fix this?
Click to expand...
Click to collapse
You need to do the short and connect the cable with the tool open first. Otherwise for some weird reason it doesn't detect the phone.
It appeared to work for me but did nothing. I hope you have better luck.
---------- Post added at 11:55 AM ---------- Previous post was at 11:12 AM ----------
Just saw your edit.
If you can enter download mode, you can now flash a tot using any online guide for such, and in theory unbrick your phone.

As for me, still no luck.
Willing to paypal gift $30.00 to anyone who can help. I've recieved some help invitations but they all insist I install whatsapp, and I can't do that without a phone...

Currently, I am flashing a kitkat kdz (D85510f_00.kdz) to the phone using LG Flash Tool 2014.
It seems to takes ages but is progressing nevertheless. After 30 minutes the tool says 14% whereas the phone says 5% on the screen. I hope the process speeds up a little...
Wish me luck
----
@ R-T-B:
Are you able to get the phone to 9008 mode? Have you tried using the plain BoardDiag 2.99a to extract from *.tot file and flash those afterwards?

MacWarrior said:
Currently, I am flashing a kitkat kdz (D85510f_00.kdz) to the phone using LG Flash Tool 2014.
It seems to takes ages but is progressing nevertheless. After 30 minutes the tool says 14% whereas the phone says 5% on the screen. I hope the process speeds up a little...
Wish me luck
Click to expand...
Click to collapse
I wish you enough luck for both of us!
But seriously, good luck. Sounds like you are in the home stretch.
EDIT: Yes, I am in 9008. Unfortunately BoardDiag seems to refuse to flash it with AP errors. I think it's an issue with the updated chipset Verizon uses on the 32gb model.

[HELP] G3 Hardbrick Help! URGENT!

Here's my case:
I've got a LG G3 F400L (Korean LGU Variant), its on Marshmallow(6.0), and for all I know I used the Autorec program for Lollipop, and apparently got my bootloader corrupted; No led flashing, no display. But the Qualcomm 9008 serial port is shown on the device manager and I can use Boardiag to detect it. I know, irony and idiocy made this dilemma.
Diagnostics:
I've used Boardiag 2.99a by willcracker and yes I've checked "AP check" and "EMMC TEST" and both are tagged as "Pass", but when it comes to the "SDRAM TEST" it throws off an error indicating that there is a flash error on partition "boot" along with a 0x3000 and I can't progress beyond that, I've also tried to use the "Restore Device" option to revive it but still the later error still persists.
I've also tried Smart Boot Diagnostics but the problem is that my device's AP Chip doesn't exist on the current version of the tool.
What I would like to press on:
I would want to resolve this on my own and that no amount of suggesting on sending this to the service center would yield fruit. Please do understand, I would also like this to be a thread that can help me and other on resolving their corrupted bootloader units.
Please, can someone help me on my dilemma. Thank you very much. Any amount of help is appreciated.

Try using board diag with the battery unplugged.
Sent from my SM-G935T using Tapatalk

Already tried that but still nothing works.
Current situation:
Alas, I've accessed fastboot and had wiped the boot partition, but now the USB is detected as "LGE AndroidNet USB Serial Port."

FeitX said:
Already tried that but still nothing works.
Current situation:
Alas, I've accessed fastboot and had wiped the boot partition, but now the USB is detected as "LGE AndroidNet USB Serial Port."
Click to expand...
Click to collapse
You need to short with a cable internet connection I do this last night and changes for Qalcomm USB in the same time...After that, you need to open BoarDiag and do the process. If you can´t enter in download mode, you need in BoarDiag pass the USERDATA
I follow this link: http://open-freax.fr/guide-unbrick-your-lg-g3/

bricked my amazon fire phone

I was trying to go back to stock os from cm11 on the Amazon fire phone. Downloaded a stock rom and tried to install using safestrap.
After I pressed reboot the phone turned off but didn't turn back on. It's not responding to anything , not even goes into recovery , but when I connect it to computer by cable , six partitions show up , five of which it says are in need of format , and one contains a folder named image , which has a lot of files.
I'm new to this , got cm by following a simple guide , help pls

Hi to you all!
I have exactly the same issue.
If I connect the Fire Phone to the Pc there are six partitions that show up. So ADB sideload is not possible any more. Ialready disconected the battery- did not work out
Does any of you have any idea?
Thanks

How come no one answered to this issue since 2016
Good day everyone,
I wonder why this issue was not replied to since 2016 on a professional forum. Is it because its not fixable?
I just bought an Amazon Fire Phone 64GB, the AT&T version. I already knew the phone was a complete disaster, but I still bought due to my low budget. Its the SnapDragon 800 series processor which I considered for such a small budget phone. Anyways, I rooted it via KingRoot, installed Safestrap-Kodiak-4.0.1-B01. I then downloaded the Unlocked version of the Fire phone Fireware "update-kindle-35.4.6.6_user_466000820" (since I wanted to avoid AT&T bloatware. I reside outside the States so cant use AT&T, so no use keeping it running all the time and sacrifice my battery) and flashed that. It flashed alright but got stuck after the welcome screen after selecting English (United Sates or UK). I then thought of of reverting it back to its original state Fire OS Ver 3.5, so downloaded "update-fire-phone-121_1.0.1_user_101012120" and now it has no life what so ever. Now it in the same state as mentioned by 2 others on this thread. It shows total 6 partitions with only 1 partition with an "Image" named Dir and a few files around 53MB or so residing in it.
I have snapshots of the Image folder files and the "QHSUSB_Bulk" status shown in Device manager, but I cant seem to find an option here to attach my jpg's here. Gosh! It doesnt get dumber than this.
Requesting help from someone who can help me out with anything at all, links, text, vdo's.
I've already downloaded the following files, but dont have a clue what to do with any one of them
QPST.2.7.460
Qualcomm_Flash_Image_Loader_v1.0.0.3
SRKtool_2.1_droidth
Qualcomm HS-USB QDLoader 9008 Driver Qualcomm HS-USB QDLoader 9008 Driver2.1.0.4
Qualcomm HS-USB QDLoader 9008 Driver Ver8.5

Have you tried going into adb sideload, installing adb drivers and sideloading the stock rom?

Now deleted the 29 partitions of the phone.
After experimenting with it, i deleted the 29 partitions of the phone, now its not even showing Qualcomm eMMC USB Storage in device manager.:crying:. Is there anyone who can help me out here. I'd really be grateful.

No life in the phone except for QDLoader 9008 (COM4)
Android# said:
Have you tried going into adb sideload, installing adb drivers and sideloading the stock rom?
Click to expand...
Click to collapse
Its not powering up, going into stock recovery even so i cant get into sideload, if my understanding is correct.

SohailAzeem said:
Its not powering up, going into stock recovery even so i cant get into sideload, if my understanding is correct.
Click to expand...
Click to collapse
*****Sorry, just realized that you can't get into stock recovery anymore please disregard the following as obviously that would only help if you could enter recovery*****
I am sure you already tried but what i meant to say was if you tried power + volume up button, you end up in stock recovery and that's where you gotta go, and select "apply update from ADB" from the recovery menu.
But even before all this, first make a new folder on your desktop, then download the ADB drivers for windows from here: https://developer.android.com/studio/releases/platform-tools.html
Extract the ADB drivers into the new folder you just made. Now, go to https://www.amazon.com/gp/help/customer/display.html?nodeId=201607550 and download the 4.6.6.1 bin file for Amazon Fire Phone, either version will work with AT&T phone, and also put the bin file in the new folder you made earlier. Rename the bin file to just 'fire' or something short and easy. Now on an empty space in that folder press Shift + Right Click together, and select 'open command prompt or windows powershell from here' depending on your computer OS.
Now make sure your phone is powered off, then press power + volume up together to get into stock recovery, and you will see option "apply update from ADB", select that and when phone is ready, connect it to the computer via usb cable. In the command prompt window on the computer, type 'adb devices' and press enter. It should show the amazon phone in adb devices list. Next, type 'adb sideload fire.bin'. If you named the bin file something else make sure you replace 'fire' with that. It will take about 5-10 minutes and once done it should be able to boot normally. You can use kingroot 4.1 and then replace the kinguser with SuperSU using the supersume app. You can download supersume app by searching online or from google appstore, either one works. Hope this helps.

SohailAzeem said:
After experimenting with it, i deleted the 29 partitions of the phone, now its not even showing Qualcomm eMMC USB Storage in device manager.:crying:. Is there anyone who can help me out here. I'd really be grateful.
Click to expand...
Click to collapse
No you bricked it good and proper now.
I have bricked 3 now
It seems while you still have QDLoader 9008 showing up the device is repairable and any Official repairer would be able to restore the phone easily with the correct software and recovery firmware package.
I was in this exact same situation and was unable to get out of this mode even after using "dd" to send the stock recovery and my backed up .img's
Once you Kill the phone in this mode (As I did) it's un fixable and Amazon will send you a new or replacement phone if it still has any manufacture warranty time left.
They will be unable to prove you tampered with it since they cant revive them :laugh:
Just tell them it bricked during a adb side load of the official firmware.

bigrammy said:
No you bricked it good and proper now.
I have bricked 3 now
It seems while you still have QDLoader 9008 showing up the device is repairable and any Official repairer would be able to restore the phone easily with the correct software and recovery firmware package.
I was in this exact same situation and was unable to get out of this mode even after using "dd" to send the stock recovery and my backed up .img's
Once you Kill the phone in this mode (As I did) it's un fixable and Amazon will send you a new or replacement phone if it still has any manufacture warranty time left.
They will be unable to prove you tampered with it since they cant revive them :laugh:
Just tell them it bricked during a adb side load of the official firmware.
Click to expand...
Click to collapse
Wow! That very sad. That was a new phone. Didnt even have a chance to use it. I thought android phones were unbrickable. What brands give away there firmware to be flashed, or in other words Phones which are unbrickable.

SohailAzeem said:
Wow! That very sad. That was a new phone. Didnt even have a chance to use it. I thought android phones were unbrickable. What brands give away there firmware to be flashed, or in other words Phones which are unbrickable.
Click to expand...
Click to collapse
If your able just return the phone as said then they will likely send you a replacement or refund. :good:
Nearly all phones are brickable if you try hard enough but this fire phone is very very easy to brick :laugh:
(In My Opinion only) If you want a cheap almost unbrickable phone then go with the cheap china brands using the MediaTek CPU's. Stay away from the flag ship brands like sony htc lg samsung which use MediaTek CPU's as these manufacturers locked their devices down by removing the MediaTek flashing method and installing their own.
SPFlashTool is the PC software and the Swiss Army knife used for MediaTek so ensure you research :good:
Team MAD (MediaTek Android Developers) Have quite a few devices they support so choose any of those depending on your budget and it will ensure you get some decent updates and running the Latest Android Version. :good:
Do your research by reading the associated threads before you choose.
https://github.com/MediatekAndroidDevelopers

i think you don't read carefully what the Problem is.
Hi to you all!
I have exactly the same issue.
If I connect the Fire Phone to the Pc there are six partitions that show up. So ADB sideload is not possible any more. The Phone is not working not getting ON. The phone is in Dead Condition but if you Connect with PC it shows its Memory Partations. if any phone not getting ON than how can enter to ADB Mode...???