Related
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Contact a software technician
juuz said:
hello,
i've got a water damaged op3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a linux logo (a small tux in the middle of the screen) and then turns off after 3 seconds. If i connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could i try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
Best regards and thanks in advance!
Click to expand...
Click to collapse
you better avoid doing experiments on op3. Symptoms you have mentioned in your thread, tells that your has been flashed (don't have usb drivers,no os,no firmware). I have faced same problem with my letv le 1s. It is a software problem. Your phone is totally empty. So do contact with any software technician, he uses sp flash tool to wake up the device. Download sp flash tool and follow procedure. If sp flash tool is detecting your device then it means your device hardware is fine.
juuz said:
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Click to expand...
Click to collapse
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
tnsmani said:
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
Click to expand...
Click to collapse
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
juuz said:
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
Click to expand...
Click to collapse
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
tnsmani said:
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
Click to expand...
Click to collapse
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
juuz said:
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
Click to expand...
Click to collapse
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
tnsmani said:
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
Click to expand...
Click to collapse
No need to worry.. Of course, you couldn't know and there are a lot of people asking dump questions..
My phone is back a life, I guess the data transfer via USB is not working anymore, charging works although I needed to take my Oneplus One's battery (identical connector, just need to take care of the pin layout [+/-]) because my OP3 battery is pretty low and I don't know if I can reactivate it.. It has about 3,4V at the moment and charges very slow..
Finally, if anyone else faces this issue and can't boot his phone:
Try different button combinations and keep holding the buttons several seconds/minutes..
hi
My phone does not enter EDL mode. When I press and release the volume keys, when I plug in the cable, the mobile charging screen appears and the earphone and Qualcomm are not detected by Windows.
ahmadjuybar said:
hi
My phone does not enter EDL mode. When I press and release the volume keys, when I plug in the cable, the mobile charging screen appears and the earphone and Qualcomm are not detected by Windows.
Click to expand...
Click to collapse
You should not release the key before you plugged into your PC.
Why don't you - adb reboot edl ?
ahmadjuybar said:
hi
My phone does not enter EDL mode. When I press and release the volume keys, when I plug in the cable, the mobile charging screen appears and the earphone and Qualcomm are not detected by Windows.
Click to expand...
Click to collapse
My OP7T HD1900 does not go to EDL mode as well. I've tried every possible way of holding the volume =/- then plugging the phone to the PC. It just jumps on to Fastboot mode everytime. Dev tools have been enabled and I've also tried long holding the buttons, not letting go long after I've plugged the phone -- no dice. Also tried the "adb reboot edl" command -- still no go. Hoping somebody's expert advise.
Skarrab22 said:
My OP7T HD1900 does not go to EDL mode as well. I've tried every possible way of holding the volume =/- then plugging the phone to the PC. It just jumps on to Fastboot mode everytime. Dev tools have been enabled and I've also tried long holding the buttons, not letting go long after I've plugged the phone -- no dice. Also tried the "adb reboot edl" command -- still no go. Hoping somebody's expert advise.
Click to expand...
Click to collapse
EDL mode doesn't show anything on the screen. You have to detect it with an app on the PC. Just throwing that out there in the event you're expecting to see a screen that says EDL or something.
xocomaox said:
EDL mode doesn't show anything on the screen. You have to detect it with an app on the PC. Just throwing that out there in the event you're expecting to see a screen that says EDL or something.
Click to expand...
Click to collapse
You're right. Screen's just supposed to remain black/blank (like it's turned off). But definitely it is not supposed to go on Fastboot display, right?
You can use Magisk to reboot into EDL mode.
Magisk->modules->3 vertical dots->reboot to EDL
Skarrab22 said:
You're right. Screen's just supposed to remain black/blank (like it's turned off). But definitely it is not supposed to go on Fastboot display, right?
Click to expand...
Click to collapse
It shouldn't go to Fastboot. That means it's not working right.
Do you need an unlocked bootloader to enter EDL mode?
speedyjay said:
Do you need an unlocked bootloader to enter EDL mode?
Click to expand...
Click to collapse
Nop
For edl mode shutdown the oneplus 7t
After this press and hold the voll + and voll - and putt in the usb cable but keep pressing the two buttons
And start the msm tool.
the op7t should be found by the edl tool, if not click on ensure.
and don't release the two buttons until you press the start button in the edl tool, otherwise the op7t will automatically exit the edl mode after a while (approx. 10 seconds)
Is Windows Device Manager supposed to show a yellow triangle on a "Qualcomm HS-USB QDLoader 9008" when in EDL mode? Event Manager shows the following error:
Code:
Device USB\VID_05C6&PID_9008\7&24d98034&0&4 was not migrated due to partial or ambiguous match.
Last Device Instance Id: USB\Vid_0E0F&Pid_0001\2370402450030061
Class Guid: {36fc9e60-c465-11cf-8056-444553540000}
Location Path: PCIROOT(0)#PCI(0701)#PCI(0003)#USBROOT(0)#USB(6)#USB(4)
Migration Rank: 0xF000FFFFFFFF0033
Present: false
Status: 0xC0000719
Source: Kernel-PnP, Event ID: 442
i think with this tool from this link http://forum.xda-developers.com/android/software/tool-tool-one-driversunlocktwrpfactory-t3358711 is the easiest way to put your 7T on EDL mode
Nevermind, I finally found the driver. It was in Windows Update, but Windows wouldn't install it automatically. I had to click on "View optional updates" and check the box for the Qualcomm driver.
ChrisFeiveel84 said:
For edl mode shutdown the oneplus 7t
After this press and hold the voll + and voll - and putt in the usb cable but keep pressing the two buttons
And start the msm tool.
the op7t should be found by the edl tool, if not click on ensure.
and don't release the two buttons until you press the start button in the edl tool, otherwise the op7t will automatically exit the edl mode after a while (approx. 10 seconds)
Click to expand...
Click to collapse
Thank you for this. My phone kept going out of EDL after a few seconds and I was afraid to start the msm tool thinking it would fail. Worked perfectly.
ChrisFeiveel84 said:
For edl mode shutdown the oneplus 7t
After this press and hold the voll + and voll - and putt in the usb cable but keep pressing the two buttons
And start the msm tool.
the op7t should be found by the edl tool, if not click on ensure.
and don't release the two buttons until you press the start button in the edl tool, otherwise the op7t will automatically exit the edl mode after a while (approx. 10 seconds)
Click to expand...
Click to collapse
THANK YOU FOR THIS!!!!
I was struggling to get it to work. One port on my laptop just kept launching Fastboot, I thought the other wasn't doing anything until I looked in control panel and saw it connected and disconnecting every 10 seconds!
ChrisFeiveel84 said:
For edl mode shutdown the oneplus 7t
After this press and hold the voll + and voll - and putt in the usb cable but keep pressing the two buttons
And start the msm tool.
the op7t should be found by the edl tool, if not click on ensure.
and don't release the two buttons until you press the start button in the edl tool, otherwise the op7t will automatically exit the edl mode after a while (approx. 10 seconds)
Click to expand...
Click to collapse
EVERYBODY WHO HAS BRICKED THEIR OP7TPRO READ THIS POST CAREFULLY. I THOUGHT MINE WAS TOAST BUT THE BUTTONS AND PLUGGING IN IS CRUCIAL FOR YOUR PC TO RECOGNIZE YOUR PHONE IN MSM.........IT WORKS...........THANK YOU CHRIS
Skarrab22 said:
My OP7T HD1900 does not go to EDL mode as well. I've tried every possible way of holding the volume =/- then plugging the phone to the PC. It just jumps on to Fastboot mode everytime. Dev tools have been enabled and I've also tried long holding the buttons, not letting go long after I've plugged the phone -- no dice. Also tried the "adb reboot edl" command -- still no go. Hoping somebody's expert advise.
Click to expand...
Click to collapse
Hi, I have the same issue. Have you found a solution?
XD-MOD2-9MM said:
Why don't you - adb reboot edl ?
Click to expand...
Click to collapse
sedated8 said:
Hi, I have the same issue. Have you found a solution?
Click to expand...
Click to collapse
`adb reboot edl` was the simplest approach for me.. and the 7t does reboot if it doesn't get connection request from MSMtool. so keep the msmtool open, and issue the reboot, MSM will automatically connect once it sees the phone.
Hey all,
So i've unlocked by bootloader, flashed a custom recovery to then proceed with LineageOS flashing. However it went completely wrong as on reboot i'm stuck with the bootloader unlocked warning and then a blackscreen.
I still have access to fastboot mode however it's impossible to flash a customer recovery ("No Such Partition") and also impossible to directly "fastboot boot recovery.img" as the phone simply reboots on the warning and then blackscreen.
The only solution seems to get the device to qualcomm EDL mode and reflash all with the MSM tool (which I have as well as all the drivers) however I cannot get my Oneplus 9 pro to EDL mode...
I've tried all the fastboot commands (fastboot oem EDL, fastboot reboot EDL, none of them work) as well as the combination volume UP + volume DOWN + plugging the cable (it just boots the fastboot mode.
Honestly would greatly appreciate any help as it is the first time in a decade I hard bricked a phone like this as it seems all the partitions are broken.
Make sure you have it unplugged when you do the button combos, as it will just start to boot while it's plugged in. Also, if you can reach fastboot, you can almost definitely reach EDL. Try unplugging and holding power+vol up for a bit which forces it to completely power off. Then try getting into EDL through the normal button combo/plugging. This is what I had to do since once it got into the booting/no-booting cycle I couldn't get to EDL.
1] Make sure you have it connected directly to your computer via USB port rather than via a USB Hub, I've seen that cause the device not to show up in the device manager.
2] You might have to restart your computer with driver signing disabled, check here for instructions for that
3] I've uploaded the Qualcomm drivers here
4] Make sure you use POWER + VOL DOWN + VOL UP and watch your device manager to see if the device is there
5] Make sure you choose the correct MSM tool from here for your region/provider
6] Remember to use MsmDownloadTool V4.0.exe, choose "User type : Others" and choose the correct device/region under the top "Target" dropdown.
7] If you don't see any COM device showing connected then try changing USB port or rebooting the device back into EDL mode.
Good advice above.
Last time I couldn't reach EDL with my previous phone, it turned out to be an issue with the drivers I had installed. I uninstalled all Android-related drivers including some generic thing that showed up in device manager when plugging in the phone, then reinstalled the latest Qualcomm drivers.
Also possibly try a different USB cable if you have one. My OP9P didn't show up when the cable it came with was plugged into my USB-C port for some reason, but it worked fine with a generic Type-A to C cable I had sitting around.
Thanks a lot for the different guidelines !
i'm 100% sure the drivers are working. I have another oneplus 9 pro that is detected when booted on EDL mode on the PC. The faulty one however cannot reach it. Also it cannot get any charge as whenever I plug it on it just goes on a boot loop. Tried to leave it to charge for a full night but still shows the "out of battery logo" with the red cable.
When plugged to the PC while pressing VOLUME UP + VOLUME DOWN I keep getting the windows sound of device plugged/unpluged, etc etc...
To be honest I think the flashing messed up the partitions as it is now hard to do anything with this device...
Tornadeur said:
Thanks a lot for the different guidelines !
i'm 100% sure the drivers are working. I have another oneplus 9 pro that is detected when booted on EDL mode on the PC. The faulty one however cannot reach it. Also it cannot get any charge as whenever I plug it on it just goes on a boot loop. Tried to leave it to charge for a full night but still shows the "out of battery logo" with the red cable.
When plugged to the PC while pressing VOLUME UP + VOLUME DOWN I keep getting the windows sound of device plugged/unpluged, etc etc...
To be honest I think the flashing messed up the partitions as it is now hard to do anything with this device...
Click to expand...
Click to collapse
I can fix it bro pm me telegram .. @Hunar71
Hunar999 said:
I can fix it bro pm me telegram .. @Hunar71
Click to expand...
Click to collapse
Can you help me too, I have exactly the same problem…
If you use Windows, you need to see "QDLOADER 9008" in Device Manager > Portable Devices.
When you got this it will work, 100% .
It worked for me a few days ago. My laptop runs on Windows 11 x64. And only have usb 3.0. NO usb 2.0.
was having the hardest time as well, it's not that the device wasn't going to EDL mode, it was but it had the wrong driver installed, thus making MSM tool not detect it in time, it is a very small window that you have where the device goes into EDL mode and the MSM tool detects it, makes a handshake with it and starts the process, but if you have the wrong driver, MSM tool will not detect the device and the device will just turn back into fastboot mode, I'm attaching a picture of the device manager where the said driver is under "Ports" ( COM & LTP ) make sure you download the above mentioned drivers, if there is any other driver under Ports, uninstall it and whenever you plug in your phone with the VOL + VOL - combo, you will see the device appear under PORTS, upgrade the currently installed driver for the one called qcmdm.inf which you'll find after you extract the .cab file that you downloaded previously, after that open MSM Tool and hit start, the port number should match the one on the device manager, now unplug the cable from your phone, power it off and do the button combination and then plug in the cable, MSM should instantly recognize the device and start the restoration.
Alberhasky said:
was having the hardest time as well, it's not that the device wasn't going to EDL mode, it was but it had the wrong driver installed, thus making MSM tool not detect it in time, it is a very small window that you have where the device goes into EDL mode and the MSM tool detects it, makes a handshake with it and starts the process, but if you have the wrong driver, MSM tool will not detect the device and the device will just turn back into fastboot mode, I'm attaching a picture of the device manager where the said driver is under "Ports" ( COM & LTP ) make sure you download the above mentioned drivers, if there is any other driver under Ports, uninstall it and whenever you plug in your phone with the VOL + VOL - combo, you will see the device appear under PORTS, upgrade the currently installed driver for the one called qcmdm.inf which you'll find after you extract the .cab file that you downloaded previously, after that open MSM Tool and hit start, the port number should match the one on the device manager, now unplug the cable from your phone, power it off and do the button combination and then plug in the cable, MSM should instantly recognize the device and start the restoration.
Click to expand...
Click to collapse
Yeah make sure it's exactly the same name of that driver - worked for me on oneplus 9
If you have access to fastboot still. Try switching slots. Then going into EDL
For anyone looking for help, please DM me.
djsubterrain said:
1] Make sure you have it connected directly to your computer via USB port rather than via a USB Hub, I've seen that cause the device not to show up in the device manager.
2] You might have to restart your computer with driver signing disabled, check here for instructions for that
3] I've uploaded the Qualcomm drivers here
4] Make sure you use POWER + VOL DOWN + VOL UP and watch your device manager to see if the device is there
5] Make sure you choose the correct MSM tool from here for your region/provider
6] Remember to use MsmDownloadTool V4.0.exe, choose "User type : Others" and choose the correct device/region under the top "Target" dropdown.
7] If you don't see any COM device showing connected then try changing USB port or rebooting the device back into EDL mode.
Click to expand...
Click to collapse
Thanks a lot man. Saved my Day. First 9Pro successfully restored ;-) Thank you and merry Christmas to all.
Guys I do not need to use the MSM Tool Anywhere until I reach the step where my device is being successfully detected as "QDLOADER 9008" in my windows device manager correct?
Or does the MSM Application need to be running when I reboot to EDL mode?
I am following this guide.
Please help
I always have phone powered off, and while holding both volume keys I plug it into USB cord(that is already plugged to pc) and then click on enum(button in msm screen) until it says connected then hurry and click start. Once it starts I can let go of volume keys.. Also more than likely u will need to click the box to "use lite firehose" or "Sahara communicaion" will keep failing.
make sure you have oneplus 9 pro drivers and " qaulcomm incorporated - Ports" Driver) and ("qaulcomm communications inc-Net" Driver) so your phone in edl which will be already most likely be running before you plug it in. just hold down both volume buttons and plug in to the usb port to your pc and release once plugged in and start the msm tool and hit enum it should say connect provided that you have all the necessary drivers above so the pc usb port will be able to communicate/recognize you device. its never usually A 1 and done type of thing. everytime i brick my phone its always the 100th try before i get a com port connected and the software communicating successfully, so just be patient and take your time. you will get it back up and running,
Hey, I wanted to ask in here instead of starting a new thread.
Right now I have an OP9p that wont boot to EDL (Only fastboot or Corrupt page)
I tried the fastboot commands but it won't work and it won't shut down, I have fixed multiple phones using MSM and know all the small issues and how to get around them but it's the first time finding a device that won't shut down and will keep rebooting tried volume up + Power for several seconds tried holding only power or the three.
Nothing it keeps rebooting and won't shut down for me to get into EDL.
Any ideas?
Thanks
awsan said:
Hey, I wanted to ask in here instead of starting a new thread.
Right now I have an OP9p that wont boot to EDL (Only fastboot or Corrupt page)
I tried the fastboot commands but it won't work and it won't shut down, I have fixed multiple phones using MSM and know all the small issues and how to get around them but it's the first time finding a device that won't shut down and will keep rebooting tried volume up + Power for several seconds tried holding only power or the three.
Nothing it keeps rebooting and won't shut down for me to get into EDL.
Any ideas?
Thanks
Click to expand...
Click to collapse
can't get into edl mode
how can I get oneplus 9 pro into edl mode while it's refusing to turn off? keep in mind that I can't use adb. but was able get fastboot devices command to work and I did not use any third party roms, didn't unlock the bootloader, and do not have...
forum.xda-developers.com
awsan said:
Hey, I wanted to ask in here instead of starting a new thread.
Right now I have an OP9p that wont boot to EDL (Only fastboot or Corrupt page)
I tried the fastboot commands but it won't work and it won't shut down, I have fixed multiple phones using MSM and know all the small issues and how to get around them but it's the first time finding a device that won't shut down and will keep rebooting tried volume up + Power for several seconds tried holding only power or the three.
Nothing it keeps rebooting and won't shut down for me to get into EDL.
Any ideas?
Thanks
Click to expand...
Click to collapse
Well you have a corrupted boot.img or you would not be trying to edl. Also you probably are holding down multiple buttons to power off to your phone and your either not remembering or forgot that these combination of buttons are booting you into other modes fastboot, recovery or system.
I tried ton of time while pressing Vol Up+Down Always T-Mobile 7T entering to Fastboot Menu.
Please someone help me.
Sorry for my English
Thank you
Your phone has to be off for it to go into EDL Mode. turn phone off then try again.
The commands ur using is for fastboot it sounds like.
Follow these steps:
Hold down Volume Up + Volume Down buttons for few seconds and plug in the USB cable, which is already attached to the computer from another side. Keep pressing until you see EDL mode. (Note: Make sure you have USB connected in PC before connecting it to the smartphone while pressing both the buttons.)
xHvlios said:
Your phone has to be off for it to go into EDL Mode. turn phone off then try again.
The commands ur using is for fastboot it sounds like.
Follow these steps:
Hold down Volume Up + Volume Down buttons for few seconds and plug in the USB cable, which is already attached to the computer from another side. Keep pressing until you see EDL mode. (Note: Make sure you have USB connected in PC before connecting it to the smartphone while pressing both the buttons.)
Click to expand...
Click to collapse
Note in EDL Mode your screen should be completely black and on device manager it should say like qsbulk or qualcomm something
hi
I used MSM 4.0 to revert the phone from Custom-ROM to stock OOS. Now the phone does not turn on at all. MSM won't write ROM. Firehos gives error. The device is waiting. Then this error occurs. Moreover, the message always arrives at 17 seconds.
I disconnected the phone from the computer. I hold down the volume down and power button. There is no reaction. I try the volume up and power button. There is no reaction. I also try the power button along with the volume down and power button. Again no response.
The phone does not turn on at all. I tried to write ROM with MSM 10 times. It is not happening.
What should I do? Please help. There is no image on the screen of the device. EDL mode appears to be active when connected to the computer. But nothing can be written to the device. from the computer
I tried the original cable. I connected from type-c. It did not happen. Problem not solved.
I also tried Baseus Type-C to Type-C cable. It did not happen.
I tried with Ugreen Type-A to Type-C cable. I've also tried USB 2.0 and 3.0 connections. It did not happen.
I tried with India ROM. It did not happen.
Please show me a solution.
OnePlus 9 Pro 12/256 GB Le-20120 model.
USB debugging was enabled on the old rom.
Try plugging your device to power outlet and wait for 1-2 minutes and see if it's turning on.
cyber.wise said:
hi
I used MSM 4.0 to revert the phone from Custom-ROM to stock OOS. Now the phone does not turn on at all. MSM won't write ROM. Firehos gives error. The device is waiting. Then this error occurs. Moreover, the message always arrives at 17 seconds.
I disconnected the phone from the computer. I hold down the volume down and power button. There is no reaction. I try the volume up and power button. There is no reaction. I also try the power button along with the volume down and power button. Again no response.
The phone does not turn on at all. I tried to write ROM with MSM 10 times. It is not happening.
What should I do? Please help. There is no image on the screen of the device. EDL mode appears to be active when connected to the computer. But nothing can be written to the device. from the computer
I tried the original cable. I connected from type-c. It did not happen. Problem not solved.
I also tried Baseus Type-C to Type-C cable. It did not happen.
I tried with Ugreen Type-A to Type-C cable. I've also tried USB 2.0 and 3.0 connections. It did not happen.
I tried with India ROM. It did not happen.
Please show me a solution.
OnePlus 9 Pro 12/256 GB Le-20120 model.
USB debugging was enabled on the old rom.
Click to expand...
Click to collapse
Use the Indian 11.2.4.4 MSM (if you have a Pro). I have the T-mobile variant and instead of using the T-Mobile MSM, Indian with "use lite firehose" and "Target" changed to India.
TheKnux said:
Use the Indian 11.2.4.4 MSM (if you have a Pro). I have the T-mobile variant and instead of using the T-Mobile MSM, Indian with "use lite firehose" and "Target" changed to India.
Click to expand...
Click to collapse
Phone connects and disconnects every 10 seconds. The full MSM Tool will start writing the file, the phone is disconnected.
I uninstalled the driver. I reinstalled. I installed it manually. I fully charged the phone. Charge is full. But I still can't solve it. I tried it in India. The same happened in the Hindi version.
In your device manager does it show the device with the correct drivers in the ports section of device manager?
This was a major problem for me when I started using msm.
Mainly the fact that the drivers are unsigned so even if you bypass that and install them you when you go to use them if the bypass doesn't persist then the drivers won't be usable.
Click the box to use "lite firehose" then soon as u plug it in click enum til it says connected then click start. Doing this the msm tool for "your device" will work
Shooter7889 said:
Click the box to use "lite firehose" then soon as u plug it in click enum til it says connected then click start. Doing this the msm tool for "your device" will work
Click to expand...
Click to collapse
what is an enum sir?
cyber.wise said:
what is an enum sir?
Click to expand...
Click to collapse
1; COM5; N/A; India; Param preload; 6 s; Device not match image
dediklerinizi yaptım. Bu mesaj geliyor.
Use Lite Firehose selected
Enum enabled
indian rom msm
15 saniyede bir bağlantı kopuyor.
It is the button to the right of the "start" button. As far as I have always understood it helps the "connected to device" to appear more easily and quicker. It seems to help detect device
Shooter7889 said:
It is the button to the right of the "start" button. As far as I have always understood it helps the "connected to device" to appear more easily and quicker. It seems to help detect device
Click to expand...
Click to collapse
operation failed. Unfortunately it doesn't.
OP 9Pro doesnt stay in EDL mode, only few seconds.
You have to start MSM tools and hit start before you enter EDL mode.
With MSM tools ready, waiting, you have to hold both volume up and down. Connect usb cable and still hold both buttons. It takes about 5-6 seconds to hold till the phone appears on MSM tools, flashing.
Also try different USB ports on computer, maybe uninstall drivers and start from scratch.