Hello lads,
I have been having issues with my OnePlus Nord N100.
On my fault, I wanted to root with magisk using fastboot. Unfortunately, I had flashed boot a magisk.img which was not compatible with OnePlus Nord N100.
The phone is currently stuck in Fastboot Mode. I have tried several times to flash boot it back to its original boot.img, unfortunately it does not work.
Every time I try to go to Recovery Mode, it leads me right back to the Fastboot main menu. I can turn off the phone and reboot it with no issues.
I believe I have soft bricked it, and I need help recovering it back to it's original state, or better yet root it in a riskless way.
Here is a list of commands and techniques I have tried so far:
- Fastboot -w
- Fastboot erase cache
- Fastboot erase boot
- Fastboot erase boot_a
- Fastboot erase boot_b
- Fastboot boot boot.img (Ends up with a failure)
- Fastboot flash boot boot.img (Command is successful, but no changes for boot)
- Tried all combinations keys to go to Recovery Mode (Power button + Volume Down Button + Volume Up Button)
Thank you for helping me out if you can.
Windwell said:
Hello lads,
I have been having issues with my OnePlus Nord N100.
On my fault, I wanted to root with magisk using fastboot. Unfortunately, I had flashed boot a magisk.img which was not compatible with OnePlus Nord N100.
The phone is currently stuck in Fastboot Mode. I have tried several times to flash boot it back to its original boot.img, unfortunately it does not work.
Every time I try to go to Recovery Mode, it leads me right back to the Fastboot main menu. I can turn off the phone and reboot it with no issues.
I believe I have soft bricked it, and I need help recovering it back to it's original state, or better yet root it in a riskless way.
Here is a list of commands and techniques I have tried so far:
- Fastboot -w
- Fastboot erase cache
- Fastboot erase boot
- Fastboot erase boot_a
- Fastboot erase boot_b
- Fastboot boot boot.img (Ends up with a failure)
- Fastboot flash boot boot.img (Command is successful, but no changes for boot)
- Tried all combinations keys to go to Recovery Mode (Power button + Volume Down Button + Volume Up Button)
Thank you for helping me out if you can.
Click to expand...
Click to collapse
Tried changing between active slot ?
Also flashed the unpatched boot.img to both slots a/b?
fastboot --set-active=a
or:
fastboot --set-active=b
AJHutchinson said:
Tried changing between active slot ?
Also flashed the unpatched boot.img to both slots a/b?
fastboot --set-active=a
or:
fastboot --set-active=b
Click to expand...
Click to collapse
Hey mate,
Thanks for responding. Sorry for the late reply.
From what you had suggested, I did "fastboot --set-active=a" , "fastboot flash boot boot.img", and "fastboot reboot" (with the stock unpatched boot.img) the commands were successful once again, but there were no effective changes.
Afterwards, I did "fastboot --setactive-b", "fastboot flash boot boot.img", and "fastboot reboot" the commands were successful once more, and this time, I was finally able to go into recovery mode. On the other hand, in recovery mode I wiped the cache and erased everything, but unfortuantely I still could not boot into Android, even though I tried to flash boot the image once more.
Thank you for these commands, as I was at least able to recover recovery mode.
Any other suggestions maybe?
Hello,
Use this tool and it will fix it, I had the same problem. Just download the software and flash it in Qualcomm EDL mode.
MSMDownload image needed
Hello guys, I managed to flash the wrong image to OnePlus NORD N100 BE2013, I overlooked for the first time what I'm doing and messed it up Now it's in Qualcomm EDL mode and I need and image to flash it to bring it back do life, anyone I can...
forum.xda-developers.com
I alsp posted boot.img which is compatible you can flash it. Link is in the comments.
Thanks
Boot.img from nord n100 in this thread, I exctracted and rooted it myself.
I WHANT RECOVERY Boot.img FOR ROOT MY ONEPLUS NORD N100
I unlock bootloader and i whant to root with magisk my phone, i need boot.img for rocovery..I try anather boot.img from One plus nord, etc, i sucessfull flash this recovery's with command in windows but is no go in recovery, stay in bootloop..Can...
forum.xda-developers.com
Hello,
I used the tool MSMDownload but unfortunately I was unable at all to boot into Qualcomm Edl mode, even though I have installed correctly all the drivers for Windows Qualcomm, and OnePlus USB drivers, and used the correct method (Volume Button UP and Down at the same time whilst connecting the phone via USB). I tried flash booting with the boot.img you gave me, but still no changes. I am still stuck in Fastboot.
If you had encountered the same issue back then, can you tell me the excat procedure you did please?
Thank you so much.
I was in the exact same situation after flashing boot.img from one plus nord by mistake.
It got so bad it was totally bricked and just got into EDL mode by holding down the up and down volume buttons and holding power on. Even the screen didn't work.
Once that started, MSMDownload tool from the N100 thread worked fine, you downloaded the proper package right?
Which model does it say on the back? This was BE2013.
I think solution for you is a fastboot image, I extracted the payload.bin to .img files and brought it back to life with it and rooted it with magisk.
The boot.img I uploaded here was from Oxygen OS 10.5.5.
If you have fastboot you should 100% be able to boot into EDL mode, just hold down the up and down volume buttons for long time and then the power button
Thanks
AJHutchinson said:
Tried changing between active slot ?
Also flashed the unpatched boot.img to both slots a/b?
fastboot --set-active=a
or:
fastboot --set-active=b
Click to expand...
Click to collapse
oh
thts ok man
بلوک سبک
I will try to make a fastboot image for OnePlus NORD N100 BE2013 with 10.5.5 and upload it to mega, I'll send you the link. If you are in fastboot mode you will be able to flash it I believe, let me have a look.
Fast boot image is ready for Oxygen 10.5.5 Nord N100 EUROPE, I am uploading it to MEGA.
motovnet said:
I was in the exact same situation after flashing boot.img from one plus nord by mistake.
It got so bad it was totally bricked and just got into EDL mode by holding down the up and down volume buttons and holding power on. Even the screen didn't work.
Once that started, MSMDownload tool from the N100 thread worked fine, you downloaded the proper package right?
Which model does it say on the back? This was BE2013.
I think solution for you is a fastboot image, I extracted the payload.bin to .img files and brought it back to life with it and rooted it with magisk.
The boot.img I uploaded here was from Oxygen OS 10.5.5.
If you have fastboot you should 100% be able to boot into EDL mode, just hold down the up and down volume buttons for long time and then the power button
Thanks
Click to expand...
Click to collapse
For some reason Qualcomm Mode Edl does not launch whatsoever.
motovnet said:
Fast boot image is ready for Oxygen 10.5.5 Nord N100 EUROPE, I am uploading it to MEGA.
Click to expand...
Click to collapse
Thank you that's very kind of you. I think the only way to fix it by flash boot.img, but I have doubts because it does not work.
The only commands I am doing are "fastboot devices", "fastboot flash boot boot.img"
With the fastboot image you will be able to flash everything, it contains not only boot.img but system and etc. I managed to boot mine and bring it back to life by reflashing everyhing.
So the only thing I need to do is "fastboot flash boot ''.img" right?
Where can I get all the nesscary files?
And how did you manage to root it?
The fastboot image flashes all partitions, not just boot with stock Oxygen OS 10.5.5
What you need to do is run flash-all.bat from the archive and it will flash the entire os not just boot.img.
If you can't get to EDL mode, fastboot flash is the only solution. What model does it say in the back? This one was EUROPE BE2013.
Is your EU or Global device?
Archive is uploading still.
Thanks
The model is the correct one. BE2013, although it does not say EU or anything.
In the archive, I would just need to run flash-all.bat which flash boots all the nesscary images correct?
Thank you once agian.
2.55 GB file on MEGA
mega.nz
This is a fastboot image for OnePlus NORD N100 EU BE2013 device.
Extract it to a new folder, it contains fastboot in it.
Right click flash-all.bat and run as admin.
You can open the flash-all.bat file with notepad to check yourself there is nothing strange in it. I used a bat file from the forum that was fastboot image for OnePlus NORD and changed it to use the .img files for OnePlus NORD N100.
Contains Oxygen 10.5.5, once you bring it back to life (IF YOU HAVE THIS MODEL), you can use magisk to patch the boot.img and flash it via fastboot.
This is how I rooted it and it worked properly.
Please use it with caution and ensure your model matches! I can not guarantee it will work on other devices.
If you can't go to EDL mode, this is your way to go, but I don't know if flashing GLOBAL version will work.
Thanks
Windwell said:
The model is the correct one. BE2013, although it does not say EU or anything.
In the archive, I would just need to run flash-all.bat which flash boots all the nesscary images correct?
Thank you once agian.
Click to expand...
Click to collapse
I would guess BE2013 is the EU one, as this worked on mine.
motovnet said:
I would guess BE2013 is the EU one, as this worked on mine.
Click to expand...
Click to collapse
Okay thank you for helping me. I will try this later and keep you in touch.
Windwell said:
Okay thank you for helping me. I will try this later and keep you in touch.
Click to expand...
Click to collapse
Thanks, let me know if it works for you. If you're unable to flash it via fastboot, only EDL will help.
Related
Hi,
I own an Honor 7X (BND-L21) European variant. I was on Oreo Beta firmware BND-L21C432B302(432log) version.
I wanted to update to stable oreo firmware following this guide by @mrmazak
But unfortunately while in twrp, it wasn't responding to my volume down button click & auto aborted (as stated in the linked thread)
So I reboot the phone & suddenly it went into stock recovery & started to update. But at 5% it failed & from then, I'm unable to flash anything.
Tried rebooting & booting into TWRP, but TWRP doesn't exist anymore & boots into erecovery or stock recovery.
Phone doesn't goes beyond Huawei logo.
Tried flashing Oreo TWRP but it fails. tried flashing stock OREO recovery from update.zip, fails.
Tried both fastboot flash recovery & fastboot flash recovery-ramdisk command
My device detail is as below
fastboot oem get-product-model : BND-L21
fastboot getvar vendorcountry : hw/eu
fastboot oem get-build-number : BND-L21 8.0.0.302(C432log)
fastboot getvar rescue_enter_recovery : getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION : BND-L21C432B102CUSTC432D001
The firmware I tried was BND-L21C432B330CUSTC432D2
Any kind of help is appreciated.
Cheers.
mumith3 said:
Hi,
I own an Honor 7X (BND-L21) European variant. I was on Oreo Beta firmware BND-L21C432B302(432log) version.
I wanted to update to stable oreo firmware following this guide by @mrmazak
But unfortunately while in twrp, it wasn't responding to my volume down button click & auto aborted (as stated in the linked thread)
So I reboot the phone & suddenly it went into stock recovery & started to update. But at 5% it failed & from then, I'm unable to flash anything.
Tried rebooting & booting into TWRP, but TWRP doesn't exist anymore & boots into erecovery or stock recovery.
Phone doesn't goes beyond Huawei logo.
Tried flashing Oreo TWRP but it fails. tried flashing stock OREO recovery from update.zip, fails.
Tried both fastboot flash recovery & fastboot flash recovery-ramdisk command
My device detail is as below
fastboot oem get-product-model : BND-L21
fastboot getvar vendorcountry : hw/eu
fastboot oem get-build-number : BND-L21 8.0.0.302(C432log)
fastboot getvar rescue_enter_recovery : getvar:rescue_enter_recovery FAILED (remote: FAIL:need all image flashed!)
fastboot oem oeminforead-SYSTEM_VERSION : BND-L21C432B102CUSTC432D001
The firmware I tried was BND-L21C432B330CUSTC432D2
Any kind of help is appreciated.
Cheers.
Click to expand...
Click to collapse
Re failing at 5% suggests to me that one of the three file was not found.
Not able to fastboot flash never happened to me.
The not booting happened to me after flashing different region firmware. And factory resetting with recovery including format cache got it to boot.
Is you bootloader unlocked. Still?
mrmazak said:
Re failing at 5% suggests to me that one of the three files was not found.
Not able to fastboot flash never happened to me.
The not booting happened to me after flashing different region firmware. And factory resetting with recovery including format cache got it to boot.
Is your bootloader unlocked? Still?
Click to expand...
Click to collapse
all 3 files were perfectly there in "HWOTA8" folder in external SD
Bootloader & FRP both unlocked still.
Firmware region is same. I matched it thoroughly.
I don't know why fastboot can't flash recovery anymore
right now, I tried to fastboot flash system with aosp GSI img. it worked... then again extracted system.img from update.app .... again bootloop.
but still the same problem with fastboot flash recovery.... can't flash recovery.
Any advice?
mumith3 said:
all 3 files were perfectly there in "HWOTA8" folder in external SD
Bootloader & FRP both unlocked still.
Firmware region is same. I matched it thoroughly.
I don't know why fastboot can't flash recovery anymore
right now, I tried to fastboot flash system with aosp GSI img. it worked... then again extracted system.img from update.app .... again bootloop.
but still the same problem with fastboot flash recovery.... can't flash recovery.
Any advice?
Click to expand...
Click to collapse
What command Are you using to flash recovery?
Code:
fastboot flash recovery_ramdisk twrp-filename.img
mrmazak said:
What command Are you using to flash recovery?
Code:
fastboot flash recovery_ramdisk twrp-filename.img
Click to expand...
Click to collapse
Sir, I tried with the RECOVERY_RAMDIS.img in your AFH .... It worked !!!! how???
Edit
Funnily, fastboot flash recovery-ramdisk works in powershell.... doesn't work with CMD..... !!!! What in the world is happening?
edit
Sir @mrmazak can not boot into fastboot anymore.... doesn't get past after stock recovery !!! any advices?
mumith3 said:
Sir, I tried with the RECOVERY_RAMDIS.img in your AFH .... It worked !!!! how???
Edit
Funnily, fastboot flash recovery-ramdisk works in powershell.... doesn't work with CMD..... !!!! What in the world is happening?
edit
Sir @mrmazak can not boot into fastboot anymore.... doesn't get past after stock recovery !!! any advices?
Click to expand...
Click to collapse
Really don't know what you are doing, it is not recovery-ramdisk It is recovery_ramdisk
Under score not dash
mrmazak said:
Really don't know what you are doing, it is not recovery-ramdisk It is recovery_ramdisk
Under score not dash
Click to expand...
Click to collapse
it was a typo in forum.... !!! :cyclops: got into fastboot.
Sir, when I install hwota8_update-auto-rename, I need to press volume down at the end of the script, roght? but my volume down button press is not being detected.... should I try the commands from directly inside TWRP terminal?
& if you don't mind, can I have your whatsapp/telegram nmbr in PM? I'm really trying to fix my phone :crying:
Current situation,
TWRP installed,
Fastboot accessible
doesn't go past huawei splash logo/twrp
Edit
Manual Flashing through TWRP terminal worked.... currently on OREO Stable
mumith3 said:
it was a typo in forum.... !!! :cyclops: got into fastboot.
Sir, when I install hwota8_update-auto-rename, I need to press volume down at the end of the script, roght? but my volume down button press is not being detected.... should I try the commands from directly inside TWRP terminal?
& if you don't mind, can I have your whatsapp/telegram nmbr in PM? I'm really trying to fix my phone :crying:
Current situation,
TWRP installed,
Fastboot accessible
doesn't go past huawei splash logo/twrp
Edit
Manual Flashing through TWRP terminal worked.... currently on OREO Stable
Click to expand...
Click to collapse
I need to look at that code I'm using, that looks for the buttons. It works sometimes and not others.
Manual reboot to recovery should have worked also. Bit good that you are back going again
edit:
updated the hwota8_update-auto-rename.zip , removed the volume button check and leave it for the user to do a reboot recovery from menu. (made this way , to be able to cancel the update for whatever reason , might arise.)
mrmazak said:
I need to look at that code I'm using, that looks for the buttons. It works sometimes and not others.
Manual reboot to recovery should have worked also. Bit good that you are back going again
edit:
updated the hwota8_update-auto-rename.zip , removed the volume button check and leave it for the user to do a reboot recovery from menu. (made this way , to be able to cancel the update for whatever reason , might arise.)
Click to expand...
Click to collapse
Thanks for all the help Sir ?
P.S. Oreo stable is pretty damn good so far.
Hello everyone! So I have a OP7T 1907 TMobile variant, and I've been following this guide to convert it. I have done it successfully a long time ago. I went to update to android 11 and after a while my flashing stopped working, I finally figured out the problem. I was getting the error. "fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable."
I was stuck here for a while so I deleted the adb folder and went to bed last night. I woke up and it suddenly was working again. I tried to update to Android 11 and it bootlooped my phone, I tried to reflash but I had already relocked the bootloader, and the command "fastboot flashing unlock_critical" would return the error I had to flip the enable oem unlock switch. So I plugged into the MSM tool and hit start. I am now stuck at the same fastboot error. Any ideas?
After trying a bunch of different stuff, flashing the international rom and it stopped. I guess that put back some files that I was missing. I was then stuck with the tmo splash screen that goes nowhere, I then restarted and I finally go to the fastbootd screen. I wiped all data. After that fastboot reboot fastboot worked, idk if I just once again got lucky or not. But It worked
having same problem, can anyone explain how to enable fastbootd for oneplus 7t indian variant?
You need stock recovery (not twrp, los recovery, etc) for fastboot reboot fastboot to enter fastbootD mode (looks like stock recovery mode with 2 lines of Chinese and 1 line of English)
HueyT said:
You need stock recovery (not twrp, los recovery, etc) for fastboot reboot fastboot to enter fastbootD mode (looks like stock recovery mode with 2 lines of Chinese and 1 line of English)
Click to expand...
Click to collapse
Not entirely true, though.
Both LOS recovery (like the one from StatixOS or Pixel Expierience) and TWRP (the unofficial 3.5.1_10) have working fastbootd.
I don't think the same can be said about the Chinese TWRP, or mauronofrio's version, however.
Good 2 know. Thanks
open platform tools zip (fastboot&adb) place everything you want to flash in same folder as open zip (it can be whole payload extracted) and that will fix fastboot error
ecompton59 said:
open platform tools zip (fastboot&adb) place everything you want to flash in same folder as open zip (it can be whole payload extracted) and that will fix fastboot error
Click to expand...
Click to collapse
I don't think this is true.
I've been trying to root my Note 9T. The bootloader has been unlocked, and I've followed a guide from here: https://unofficialtwrp.com/twrp-3-4-2-root-redmi-note-9-5g-cannon/
I'm now stuck in a bootloop.
Anyone been successful?
I additionally tried using a different version of TWRP, which wiped the "misc" partition. Can anyone provide an image dump of the misc partition so I can flash it back on? I can't find a copy of misc in the stock firmware file.
UPDATE 1:
I put the full stock image back on and am back to having a working unrooted phone, so I don't need the misc image. Would really like to get this thing rooted though.
I've installed the Magisk APK, patched the boot image, and flashed it. But this also results in a boot loop. If I flash the stock image back it works again. Any ideas what's going on here?
UPDATE 2:
I got it working! The key was to flash the stock vbmeta.img with fastboot functions to disable it.
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
Hiya. I've tried that and managed to get to the twrp page. However, when I go to install magisk via twrp, it just reboots into a bootloop. Any ideas?
Update: This seems to have worked.
[SOLVED] Phone gets stuck in bootloop if I try to install Magisk ZIP!
From the forum I followed these step to install magisk: - Patched my boot.img of my current rom using Magisk Manager and flashed via fastboot - After rebooting from fastboot it got stuck in recovery so had to wipe all data and it booted finally...
forum.xda-developers.com
Did you manage to get Magisk working after the reinstall of stock firmware, or you've just resolved the bootloop?
dsclee1 said:
I've been trying to root my Note 9T. The bootloader has been unlocked, and I've followed a guide from here: https://unofficialtwrp.com/twrp-3-4-2-root-redmi-note-9-5g-cannon/
I'm now stuck in a bootloop.
Anyone been successful?
I additionally tried using a different version of TWRP, which wiped the "misc" partition. Can anyone provide an image dump of the misc partition so I can flash it back on? I can't find a copy of misc in the stock firmware file.
UPDATE 1:
I put the full stock image back on and am back to having a working unrooted phone, so I don't need the misc image. Would really like to get this thing rooted though.
I've installed the Magisk APK, patched the boot image, and flashed it. But this also results in a boot loop. If I flash the stock image back it works again. Any ideas what's going on here?
UPDATE 2:
I got it working! The key was to flash the stock vbmeta.img with fastboot functions to disable it.
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
Click to expand...
Click to collapse
I'm interesting in at least rooting and if possible install TWRP .
Can you post i complete procedure to root the note 9 T ?
Thanks
I can have a go. But I'm not 100% sure what exact steps I took that got it working, as I flashed and re-flashed several times. Give this a try and let me know if it works or not?
WARNING: EXPECT TO LOSE ALL THE DATA ON YOUR PHONE!
Step 1
Obviously you need to unlock the bootloader first: https://en.miui.com/unlock/
If you haven't done this already, after your application it's likely you might have to wait 7 days before Xiaomi actually let you unlock.
Unlocking wipes your data.
Step 2
Start the phone normally. Copy the latest magisk apk (https://github.com/topjohnwu/Magisk/releases) over to the phone and install it.
Step 3
Find the correct original ROM for your device (https://xiaomifirmwareupdater.com/miui/cannong/). You'll need the full image. From the ROM extract the boot.img and vbmeta.img. Copy the boot.img over to your phone.
Step 4
In magisk choose the option to install and select "Select and Patch a File" (should be the only option anyway). Select the boot.img you copied over. This will produce a new file called something like "magisk_patched-22100_XXXXX.img". Copy this file off your phone and onto your computer.
Step 5
Boot your phone to fastboot mode (you should already know how to do this, as you would have had to have done it to unlock your phone in the first place - Hold down Volume Down and the Power button at the same time).
Step 6
Run the following commands (obviously replace the boot image with the correct magisk image, and use the vbmeta.img you took from the ROM):
Code:
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot flash boot magisk_patched-22100_XXXXX.img
Hopefully this will work. But I can't be 100% sure, as the disabling of "verity" could mean that your encrypted user data now can't be read (if you've only just unlocked the bootloader then you're not going to have any data anyway, so not too much of an issue). If this is the case it's likely you'll now need to factory reset the phone. Hold down Volume Up and Power on start to reach the stock recovery menu, and there's a selection for factory reset. You can also install TWRP at this point, and could then use it's factory reset function instead. I downloaded this version of TWRP: https://www.mediafire.com/file/ou8553psro9yyt2/3.4.2_redmi_note_9_5G.rar/file, which came from the other rooting guide (https://unofficialtwrp.com/twrp-3-4-2-root-redmi-note-9-5g-cannon/ - which didn't work). Just flash that version of TWRP to the recovery partition (fastboot flash recovery recovery.img), and ignore all the steps given in the guide it came from.
Let me know how you get on.
sorry for the answer delay.
Adding my 2 cents about unlocking the bootlader .
In order to do it .
FIRST - do not try it from a virtual PC . It does not work (at least it did not work for me)
SECOND , before to run the xiaomi batch_unlock bootlader , don't forget to update google usb drivers
I hard some hard time to just connect the unlocker to my phone . Now i have to wait 167 hours to complete the process .
dsclee1 said:
I've been trying to root my Note 9T. The bootloader has been unlocked, and I've followed a guide from here: https://unofficialtwrp.com/twrp-3-4-2-root-redmi-note-9-5g-cannon/
I'm now stuck in a bootloop.
Anyone been successful?
I additionally tried using a different version of TWRP, which wiped the "misc" partition. Can anyone provide an image dump of the misc partition so I can flash it back on? I can't find a copy of misc in the stock firmware file.
UPDATE 1:
I put the full stock image back on and am back to having a working unrooted phone, so I don't need the misc image. Would really like to get this thing rooted though.
I've installed the Magisk APK, patched the boot image, and flashed it. But this also results in a boot loop. If I flash the stock image back it works again. Any ideas what's going on here?
UPDATE 2:
I got it working! The key was to flash the stock vbmeta.img with fastboot functions to disable it.
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
Click to expand...
Click to collapse
ive been trying for the last 4 hours to flash twrp on my redmi note 9T 5g global..can you please explain to me how you got it to work. i flashed the recovery.img and vbmeta.img file that i got from the unofficialtwrp.com download, when i flash boot recovery.img, it just reboots my phone into normal...and i missing something? My device is on Miui 12.0.8.0 andriod 10. should i be on the new update 12.5 andriod 11 for it to work. Please help.
dsclee1 said:
I can have a go. But I'm not 100% sure what exact steps I took that got it working, as I flashed and re-flashed several times. Give this a try and let me know if it works or not?
WARNING: EXPECT TO LOSE ALL THE DATA ON YOUR PHONE!
Step 1
Obviously you need to unlock the bootloader first: https://en.miui.com/unlock/
If you haven't done this already, after your application it's likely you might have to wait 7 days before Xiaomi actually let you unlock.
Unlocking wipes your data.
Step 2
Start the phone normally. Copy the latest magisk apk (https://github.com/topjohnwu/Magisk/releases) over to the phone and install it.
Step 3
Find the correct original ROM for your device (https://xiaomifirmwareupdater.com/miui/cannong/). You'll need the full image. From the ROM extract the boot.img and vbmeta.img. Copy the boot.img over to your phone.
Step 4
In magisk choose the option to install and select "Select and Patch a File" (should be the only option anyway). Select the boot.img you copied over. This will produce a new file called something like "magisk_patched-22100_XXXXX.img". Copy this file off your phone and onto your computer.
Step 5
Boot your phone to fastboot mode (you should already know how to do this, as you would have had to have done it to unlock your phone in the first place - Hold down Volume Down and the Power button at the same time).
Step 6
Run the following commands (obviously replace the boot image with the correct magisk image, and use the vbmeta.img you took from the ROM):
Code:
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot flash boot magisk_patched-22100_XXXXX.img
Hopefully this will work. But I can't be 100% sure, as the disabling of "verity" could mean that your encrypted user data now can't be read (if you've only just unlocked the bootloader then you're not going to have any data anyway, so not too much of an issue). If this is the case it's likely you'll now need to factory reset the phone. Hold down Volume Up and Power on start to reach the stock recovery menu, and there's a selection for factory reset. You can also install TWRP at this point, and could then use it's factory reset function instead. I downloaded this version of TWRP: https://www.mediafire.com/file/ou8553psro9yyt2/3.4.2_redmi_note_9_5G.rar/file, which came from the other rooting guide (https://unofficialtwrp.com/twrp-3-4-2-root-redmi-note-9-5g-cannon/ - which didn't work). Just flash that version of TWRP to the recovery partition (fastboot flash recovery recovery.img), and ignore all the steps given in the guide it came from.
Let me know how you get on.
Click to expand...
Click to collapse
should I be on the latest version of Miui...12.5 android 11? for me to be able to install twrp. i downgraded back to Miui 12.0.8.0 android 10 as i didnt like my data folder been blocked in android folder. My device is global cannong redmi 9T 5g with diminsity 800u soc, can you please help if you can. thanks in advance
Android 10 is fine. You need to fastboot flash recovery recovery.img
To boot into it you need to turn the phone off, then hold vol up and power until you feel a buzz, then let go.
I have the same Problem as HighEndGamer:
if I enter 'fastboot flash recovery recovery.img', it sayes that everything worked OK in just a few seconds. But nothing realy happend!
If I enter 'fastboot boot recovery.img', phone boot just as normal.
If I enter 'fastboot oem device-info', it sayes "FAILED (remote: unknown command)'.
If I enter 'fastboot oem lock', it works and I have to start from the beginning..
I have MIUI Global 12.0.2.0{QJEEUMX)
chmick said:
sorry for the answer delay.
Adding my 2 cents about unlocking the bootlader .
In order to do it .
FIRST - do not try it from a virtual PC . It does not work (at least it did not work for me)
SECOND , before to run the xiaomi batch_unlock bootlader , don't forget to update google usb drivers
I hard some hard time to just connect the unlocker to my phone . Now i have to wait 167 hours to complete the process .
Click to expand...
Click to collapse
I confirm it does not work from a VM (and the need for latest drivers). There is something funky going on with the USB communication when running from a VM: the first call of the fastboot executable from the windows VM generally works fine, but any other call hang. So the batch_unlock tool cannot work (since it does call fastboot several times).
Had an 11.2.3.3 Global rooted via Magisk OP9 Pro that I wanted to update via OTA to 11.2.4.4, which was offered via system update. I used Magisk to restore images before update, did the update, and then went back to install to inactive slot. Rebooted and it was still on 11.2.3.3 so I tried again. Upon trying again, my phone got to a Qualcomm debug/error mode. I experienced this before when on a different boot slot for some other diagnosis of another issue in the past so I switched boot slots.
The other boot slot is stuck in fastboot mode I come to find so I check what it shows if I reverted back to the other boot slot, which was the Qualcomm error. Now instead of a Qualcomm error, it shows language options, one of which is English, and then gives me "boot reason", "wipe data and cache" and "advanced". I believe this is the OnePlus recovery menu, which I have not needed to use before and in the past, used TWRP on other devices.
Can't I just reflash a whole system image for 11.2.4.4 (it'd have to be the European one right now since Global isn't available) via fastboot and it should be fixed, albeit unrooted and I can just re-root? I'd like to try this, but there's no "flash-all.bat" and I don't know the proper flash order for the Euro images within payload.bin as there's no xml file (I looked up a guide for directions on how to flash without flash-all.bat that I have used on other devices). Oh, and I tried to fastboot a known good boot.img and on one of the slots, it works fine, but still wont boot. The other gives error "FAILED (remote: Failed to load/authenticate boot image: Load Error)". I'm stumped.
Wondering if this has been experienced by anyone else before. Wiping my device is the last resort and shall be avoided at all costs after how much I have configured it to my liking.
I saw the following on another guide:
Code:
fastboot flash boot boot.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash recovery recovery.img
fastboot --disable-verity flash vbmeta vbmeta.img
fastboot --disable-verity flash vbmeta_system vbmeta_system.img
fastboot reboot fastboot
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash cmnlib cmnlib.img
fastboot flash cmnlib64 cmnlib64.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash logo logo.img
fastboot flash mdm_oem_stanvbk mdm_oem_stanvbk.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash odm odm.img
fastboot flash opproduct opproduct.img
fastboot flash qupfw qupfw.img
fastboot flash spunvm spunvm.img
fastboot flash storsec storsec.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash system system.img
fastboot flash vendor vendor.img
fastboot flash product product.img
Followed this guide here after extracting the Europe full system image via Payload-dumper and it now boots somewhat, but after it looks like it's loading into OOS and boot is complete, I get a black screen instead of the lock screen. I get charging sounds when plugged into the computer, but just a black screen.
How to Create Fastboot-flashable Factory Image for Any OnePlus Phone
Learn how to create a factory image for any OnePlus phone and flash it using Fastboot. Useful for restoring stock OxygenOS software and unbricking.
www.thecustomdroid.com
Wondering if this has to do with the Europe 11.2.4.4 on my Global device. Going to try reverting to 11.2.2.2 Global full image now.
Geez, good luck
vibrantliker said:
Geez, good luck
Click to expand...
Click to collapse
Just tried flashing the older 11.2.2.2 images one at a time and now it's stuck in recovery...
The closest I can get it to full booting is with 11.2.4.4 Europe full image and I get a black screen only, after it boots up with the OnePlus logo. When plugged in, I get a charging sound every 10-20 seconds or so. Too bad there's no 11.2.4.4 full image for Global or I'd try that.
Also just tried fastboot boot 11.2.4.4_global_boot.img on this 11.2.4.4 Europe image and still no go. Boots and makes sounds, but black screen still.
Have you tried the MSM tool?
hadesflames said:
Have you tried the MSM tool?
Click to expand...
Click to collapse
I was considering it, but don't want to lose any data. Next step is to contact OnePlus technical support during normal hours and see if they can work with me to resolve this one. I believe I read here on XDA that people have contacted them and usually are able to resolve the issue. Trying to avoid clearing data as the device is fine as it boots, but I think the Europe image is conflicting somewhere and not allowing me into the system since it boots all the way to the lock screen, but I don't see a lock screen, just a blank screen with sounds after boot seemingly working, along with charging sounds (albeit, sounding every 10-20s like its periodically charging).
This is so odd though because I did everything as I should've and update seemingly occurred, but system version still showed 11.2.3.3. So I go back to system update and it said there was an issue and to restart again. Did that two times with magisk revert image and restore to inactive and it then stopped booting.
If you're able to get to the recovery you can try sideloading the zip file
ADB Sideload name.zip
That should put the rom back to default, I would reboot the phone back into recovery and then do a wipe or go to fastboot and use "fastboot -w" to wipe the userdata
djsubterrain said:
If you're able to get to the recovery you can try sideloading the zip file
ADB Sideload name.zip
That should put the rom back to default, I would reboot the phone back into recovery and then do a wipe or go to fastboot and use "fastboot -w" to wipe the userdata
Click to expand...
Click to collapse
Does stock recovery support ADB? At 8 pro you needed modified one..
pyry666 said:
Does stock recovery support ADB? At 8 pro you needed modified one..
Click to expand...
Click to collapse
As far as I know, it should do as long as the drivers are installed properly, you can check with "ADB Devices", if you see the number returned then the phone is responding.
As for the fastboot commands above, I know there was a post on the OP7P forum that would make fastboot script packs for each build, if you use the script from those, you should able to amend it to flash the images above. Afaik the structure is likely the same anyway. The post also shows "ADB push" commands you can use to flash individual images to the phone.
I might have a look later and see if I can make a similar one although there seems to be a lot more build versions on the OP9P than there were for the OP7P.
Might just be easier to use the Payload Dumper program to unpack the images from the payload.bin file (instructions here) and then use a generic script to flash them to the phone, all the different models should have similar images although I do know there's an additional India.img for the Indian models (which I think is also shown in the global rom).
djsubterrain said:
As far as I know, it should do as long as the drivers are installed properly, you can check with "ADB Devices", if you see the number returned then the phone is responding.
Click to expand...
Click to collapse
I was just corious, not at home right now so i cant test. My drivers are fine and have no issues..I am using linux myself though
pyry666 said:
I was just corious, not at home right now so i cant test. My drivers are fine and have no issues..I am using linux myself though
Click to expand...
Click to collapse
Yeah I'm working at the moment so not on my own PC, can't really test it out
djsubterrain said:
Yeah I'm working at the moment so not on my own PC, can't really test it out
Click to expand...
Click to collapse
Just tried. ADB with stock recovery is "unauthorized"..So modified is needed if one wants to use stock recovery with adb
djsubterrain said:
As far as I know, it should do as long as the drivers are installed properly, you can check with "ADB Devices", if you see the number returned then the phone is responding.
As for the fastboot commands above, I know there was a post on the OP7P forum that would make fastboot script packs for each build, if you use the script from those, you should able to amend it to flash the images above. Afaik the structure is likely the same anyway. The post also shows "ADB push" commands you can use to flash individual images to the phone.
I might have a look later and see if I can make a similar one although there seems to be a lot more build versions on the OP9P than there were for the OP7P.
Might just be easier to use the Payload Dumper program to unpack the images from the payload.bin file (instructions here) and then use a generic script to flash them to the phone, all the different models should have similar images although I do know there's an additional India.img for the Indian models (which I think is also shown in the global rom).
Click to expand...
Click to collapse
I tried flashing all of the 11.2.4.4 Europe full system image payload_dumper extracted images (such as boot.img, system.img, dtbo.img) to the phone and I get where I am now. It goes through boot, but no lock screen, just a non-lit/black screen with sounds that the phone is charging when plugged in and is recognized by the computer (but can't see internal storage since you have to use notification center to turn on usb storage).
bulletbling said:
I tried flashing all of the 11.2.4.4 Europe full system image payload_dumper extracted images (such as boot.img, system.img, dtbo.img) to the phone and I get where I am now. It goes through boot, but no lock screen, just a non-lit/black screen with sounds that the phone is charging when plugged in and is recognized by the computer (but can't see internal storage since you have to use notification center to turn on usb storage).
Click to expand...
Click to collapse
See if you can do a fastboot -w to wipe the userdata in case it's been left with unusable data.
djsubterrain said:
See if you can do a fastboot -w to wipe the userdata in case it's been left with unusable data.
Click to expand...
Click to collapse
This is what I'm trying to avoid...
Since it mostly boots on the Euro 11.2.4.4, I feel that the Global full image would resolve this, but OnePlus never updates their darn website with the latest for Global.
bulletbling said:
This is what I'm trying to avoid...
Since it mostly boots on the Euro 11.2.4.4, I feel that the Global full image would resolve this, but OnePlus never updates their darn website with the latest for Global.
Click to expand...
Click to collapse
Are there actual hw differences between AA and BA?
bulletbling said:
This is what I'm trying to avoid...
Since it mostly boots on the Euro 11.2.4.4, I feel that the Global full image would resolve this, but OnePlus never updates their darn website with the latest for Global.
Click to expand...
Click to collapse
There's a pinned post at the top of the forum with all the available latest roms. Not sure they've added Global yet tho. Best going there or Oxygen Updater (when the phone is working) than the download page tbh, OnePlus ALWAYS takes ages to add builds there
pyry666 said:
Are there actual hw differences between AA and BA?
Click to expand...
Click to collapse
Not that I know of, but I have seen users use the Europe image to update their device on this forum before with the OP9Pro because they either didn't want to wait or needed to fix their device for whatever reason and the Europe version worked fine. So I don't know if this is different on 11.2.4.4.
bulletbling said:
Not that I know of, but I have seen users use the Europe image to update their device on this forum before with the OP9Pro because they either didn't want to wait or needed to fix their device for whatever reason and the Europe version worked fine. So I don't know if this is different on 11.2.4.4.
Click to expand...
Click to collapse
I know that BA is coming first than AA. Dont know reason for that but with op8p situation was same. Then was talk about googles servers or something but cant remember what that was exactly because it never affected me..
pyry666 said:
I know that BA is coming first than AA. Dont know reason for that but with op8p situation was same. Then was talk about googles servers or something but cant remember what that was exactly because it never affected me..
Click to expand...
Click to collapse
I wish I could go without my phone for weeks until they post the latest firmware to see if that even works, but I can't so I guess I'll have to use the msm tool and wipe all of my internal storage of documents, including taxes, and various files and downloads I've amassed over the past half decade. This really sucks. All because of a simple OTA that should've never caused this. They really should prevent this from being possible with the OTA update tool built-in to their system.
Hello
I've just ordered my Pixel 6 Pro, coming from the OnePlus 8 Pro.
I love tinkering with Root/Kernels/Roms.
So my question is, if there is always a way to get back to stock in case of emergency?
The OnePlus phones are considered as "unbreakable", because You can ALWAYS unbrick it via MSM unbrick tool.
Would be nice to know when I start unlocking the bootloader of my Pixel
Thanks!
Sorry that Pixel doesn't have that unbrick tool ...
The only one is a batch commend file - Flash-All extracted from factory full ROM ...
It is possible to hardbrick a Pixel device without hopes of getting it running again, for example if you nuke your recovery.
Most softbricks can be solved by either doing what Kris Chen suggested, or by using
Android Flash Tool
flash.android.com
or
Google Pixel - Update and Software Repair
After flashing a module that bootloops you can try this:
If it almost boots up but flashes, in a cmd window type:
adb wait-for-device shell magisk --remove-modules
It may grab that and remove all modules. If it doesn't, you can try this:
1. fastboot flash boot boot.img, reboot.
2. long press power button, then long press "power off", click ok to enter safemode.
3. Before your phone boots all the way up, boot to fastboot.
4. fastboot flash boot magisk_patched.img, reboot.
5. In cmd window type: adb wait-for-device shell magisk --remove-modules
6. Your phone will boot up with root and all modules removed.
There's a shortcut to safemode that removes everything but I'm not sure what it is.
Edit: boot.img is taken from the applicable firmware you are on downloaded from Google. Unzip the main zip, go into the folder and unzip the image zip that is inside.
Thank you all for your detailed information, very appreciated
Could someone check if the following is the right procedure to revert to stock kernel?
fastboot flash boot <magisk-patched-image>.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash dtbo dtbo.img
fastboot reboot fastboot (wait a bit, this takes a bit of time until you see the fastbootd screen)
fastboot flash vendor_dlkm vendor_dlkm.img
fastboot reboot
And do I have to do this procedure everytime before switching from a custom kernel to another kernel?
Thanks!
Lycidias said:
Thank you all for your detailed information, very appreciated
Could someone check if the following is the right procedure to revert to stock kernel?
fastboot flash boot <magisk-patched-image>.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash dtbo dtbo.img
fastboot reboot fastboot (wait a bit, this takes a bit of time until you see the fastbootd screen)
fastboot flash vendor_dlkm vendor_dlkm.img
fastboot reboot
And do I have to do this procedure everytime before switching from a custom kernel to another kernel?
Thanks!
Click to expand...
Click to collapse
Yes, correct, and yes, safest to do so each time switching kernels.