I was trying to update to MIUI 12 on my Note 8.
I installed Orange Fox and did all the correct procedures.
I tried to install the ROM miui_GINKGOGlobal_V12.0.1.0.QCOMIXM_f5da3c2665_10. 0.zip but Orange Fox presented an error message saying that I was trying to install the wrong version and that my phone would need the Willow version.
I downloaded the version miui_WILLOWEEAGlobal_V12.0.1.0.QCXEUXM_87056480ce_ 10.0 and Orange Fox managed to complete the installation.
But that's when my problems started: my phone is no longer on. I turn on the power button and it flashes and turns off.
If I try the power button / volume combination - the Fastboot screen flashes for a second and goes out.
If I connect the USB cable it is flashing, turning on and off.
Is there anything I can do or is my phone a brick?
Anyone have tryed the EDL in cases like this?
https://miui15.blogspot.com/2019/07/edl-mode-or-test-points-for-redmi-note-8.html
marcelopessanha said:
Anyone have tryed the EDL in cases like this?
https://miui15.blogspot.com/2019/07/edl-mode-or-test-points-for-redmi-note-8.html
Click to expand...
Click to collapse
edl mode is locked,
go to service center
Redmi 4A abdal said:
edl mode is locked,
go to service center
Click to expand...
Click to collapse
EDL locked? Why? I do not understand. It is a physical procedure
if you sure your phone is ginkgo then NEVER and EVER try to flash other device rom, you flash willow and because miui rom includes the firmwares as well then this behavior will be expected from flashing wrong driver
there's problem with your recovery, i use twrp and never encounter anything like that
---------- Post added at 02:42 PM ---------- Previous post was at 02:41 PM ----------
marcelopessanha said:
EDL locked? Why? I do not understand.
Click to expand...
Click to collapse
it need authorized xiaomi account, few peoples has it but most of them arent trustworthy
better option are going to service center
I did the EDL boot and now all is fine!!!
Works perfect!!!
marcelopessanha said:
I did the EDL boot and now all is fine!!!
Works perfect!!!
Click to expand...
Click to collapse
nice !
you followed the tutorial here ???
https://miui15.blogspot.com/2019/07/edl-mode-or-test-points-for-redmi-note-8.html
and was your bootloader locked or not ?
loopypalm said:
nice !
you followed the tutorial here ???
https://miui15.blogspot.com/2019/07/edl-mode-or-test-points-for-redmi-note-8.html
and was your bootloader locked or not ?
Click to expand...
Click to collapse
Yes, I followed this tutorial.
My bootloader had been unlocked
The phone is now working perfectly, with all apps and files restored from backup.
Related
power button is broken.
Flashed an odin stock (tried multiple) and I m still getting stuck on samsung logo
with no power button, I cant get to recovery to wipe/reset
any ideas boys?
ordered the replacement power switch but it's a long wait for it to reach me. I not in the US currently
nabilbek said:
power button is broken.
Flashed an odin stock (tried multiple) and I m still getting stuck on samsung logo
with no power button, I cant get to recovery to wipe/reset
any ideas boys?
ordered the replacement power switch but it's a long wait for it to reach me. I not in the US currently
Click to expand...
Click to collapse
http://youtu.be/pqBgbN8NLjI
sounds crazy , but i did this to my sons t989 a year ago and still working-might be worth a try
Fasted12 said:
http://youtu.be/pqBgbN8NLjI
sounds crazy , but i did this to my sons t989 a year ago and still working-might be worth a try
Click to expand...
Click to collapse
tried a lot man
the button seems completely dead
nabilbek said:
tried a lot man
the button seems completely dead
Click to expand...
Click to collapse
you know, unless you have a touch recovery , getting there wont help with a bad power button
Fasted12 said:
you know, unless you have a touch recovery , getting there wont help with a bad power button
Click to expand...
Click to collapse
yep ... using latest twrp
but I dont think there is a way into recovery if you are unable to boot the phone and no power button
I need something like a odin flashable tar that wipes cache /resets (because this usually fixes the stuck on logo)
nabilbek said:
yep ... using latest twrp
but I dont think there is a way into recovery if you are unable to boot the phone and no power button
I need something like a odin flashable tar that wipes cache /resets (because this usually fixes the stuck on logo)
Click to expand...
Click to collapse
flashing anything with a fluky power button is very hazardous. If it goes off in the middle of something, your device could be toast.
I'd get it fixed before doing anything. if it can't be fixed....phone shopping time! [emoji106]
KJ said:
flashing anything with a fluky power button is very hazardous. If it goes off in the middle of something, your device could be toast.
I'd get it fixed before doing anything. if it can't be fixed....phone shopping time! [emoji106]
Click to expand...
Click to collapse
I ordered a new power switch but I am bad at waiting
nabilbek said:
I ordered a new power switch but I am bad at waiting
Click to expand...
Click to collapse
You're risking your phone flashing anything.
But its yours to do with as you wish. Just would suck to finally get that power button delivered....and not have a functioning phone to use it with.
nabilbek said:
I ordered a new power switch but I am bad at waiting
Click to expand...
Click to collapse
you could try installing adb http://forum.xda-developers.com/showthread.php?t=1853159
Fasted12 said:
you could try installing adb http://forum.xda-developers.com/showthread.php?t=1853159
Click to expand...
Click to collapse
I am aware and have adb. thing is phone is bricked after last update (stuck at logo)
so i can only get into download mode ....wish there was a way to get from download to recovery but I cant find any
without the use of the power button ofc ...
nabilbek said:
I am aware and have adb. thing is phone is bricked after last update (stuck at logo)
so i can only get into download mode ....wish there was a way to get from download to recovery but I cant find any
without the use of the power button ofc ...
Click to expand...
Click to collapse
sorry man, hope the button install goes well
hmm
Fasted12 said:
sorry man, hope the button install goes well
Click to expand...
Click to collapse
i have the same exact problem minus my power button, it works normal
and i get firmware upgrade encountered an issue
i get that screen when i normal boot it, try recovery, or download mode, everything results to firmware upgrade encountered an issue
not sure if i should post here with this or not, just letting you know
ovenbird said:
i have the same exact problem minus my power button, it works normal
and i get firmware upgrade encountered an issue
i get that screen when i normal boot it, try recovery, or download mode, everything results to firmware upgrade encountered an issue
not sure if i should post here with this or not, just letting you know
Click to expand...
Click to collapse
i guess the question is, can you get your phone to download mode...
download mode
Fasted12 said:
i guess the question is, can you get your phone to download mode...
Click to expand...
Click to collapse
it reaches download mode no matter what i do ( the firmware error is in the download mode )
the problem is while in download mode nothing recognizes it ( its not normal download mode )
Im getting this :
I cant post links but this is the image i can send you
cdn.droidviews.com/wp-content/uploads/2013/09/Firmware-upgrade-encountered-an-issue jpg
put a DOT in there
ovenbird said:
it reaches download mode no matter what i do ( the firmware error is in the download mode )
the problem is while in download mode nothing recognizes it ( its not normal download mode )
Im getting this :
I cant post links but this is the image i can send you
cdn.droidviews.com/wp-content/uploads/2013/09/Firmware-upgrade-encountered-an-issue jpg
put a DOT in there
Click to expand...
Click to collapse
if kies wont recognize, nor will odin-i dont know--try reposting maybe get some new views, sorry
ovenbird said:
i have the same exact problem minus my power button, it works normal
and i get firmware upgrade encountered an issue
i get that screen when i normal boot it, try recovery, or download mode, everything results to firmware upgrade encountered an issue
not sure if i should post here with this or not, just letting you know
Click to expand...
Click to collapse
this happened with me once. long long time ago
But I swear I cant remember why
here try this : https://www.youtube.com/watch?v=GbAJH_mL6N4
another well explained guide for solving using kies : http://androidcentral.us/2013/09/how-to-fix-firmware-upgrade-encountered-an-issue-on-kies/
In case anyone doesn't know.....Odin won't see your device if kies is running. You need to kill the kies process. Make sure there's no mention of it in windows task manager.
Then, if your drivers are installed right....Odin should see your phone.
Also, I've always had the best luck with Odin 3.04.
---------- Post added at 07:31 PM ---------- Previous post was at 07:30 PM ----------
Or uninstall kies... I never once used it for anything.
KJ said:
In case anyone doesn't know.....Odin won't see your device if kies is running. You need to kill the kies process. Make sure there's no mention of it in windows task manager.
Then, if your drivers are installed right....Odin should see your phone.
Also, I've always had the best luck with Odin 3.04.
---------- Post added at 07:31 PM ---------- Previous post was at 07:30 PM ----------
Or uninstall kies... I never once used it for anything.
Click to expand...
Click to collapse
exactly ... kies is utter ****!
I would never recommend it too. A pure waste of time
Also, see what your phone shows as in windows device manager. If its listed with an "!" on it....the drivers may need to be reinstalled. If windows doesn't see it correctly, either will Odin. ?
Problem solved, I reinstalled drivers.
That simple.
Thanks for the video btw, I even added the guy from youtube channel
Hi to all,
yesterday I attempted to install LineageOS on my LG G4 h815.
I followed this tutorial -> https://forum.xda-developers.com/g4/general/howto-complete-guide-to-unlock-twrp-t3370003
Everything went fine. I was able to boot under LineageOS reinstall my apps etc, etc.
This morning when I woke up everything seemed normal too. But, few minutes ago, I sent an SMS via Google Messages the phone froze and then black screen.
When it froze I had 97% battery.
Ï tried to reboot it with power button -> Nothing.
I tried to remove the battery put it back on and pressed the power button -> One tiny vibration but nothing
I tried several times the same last process and finally I managed to get the screen with "Bootloader state : Unlocked !", but I cannot go further.
If I connect the phone with a USB cable, wether he's "turned on" or turned off no led is blinking.
Does someone have a clue to fix this or has ever encountered this issue ?
Tanks in advance and do not hesitate to refer to an old post. I wil check (but found no same case).
Jérémie.
Monkeypox95 said:
Hi to all,
yesterday I attempted to install LineageOS on my LG G4 h815.
I followed this tutorial -> https://forum.xda-developers.com/g4/general/howto-complete-guide-to-unlock-twrp-t3370003
Everything went fine. I was able to boot under LineageOS reinstall my apps etc, etc.
This morning when I woke up everything seemed normal too. But, few minutes ago, I sent an SMS via Google Messages the phone froze and then black screen.
When it froze I had 97% battery.
Ï tried to reboot it with power button -> Nothing.
I tried to remove the battery put it back on and pressed the power button -> One tiny vibration but nothing
I tried several times the same last process and finally I managed to get the screen with "Bootloader state : Unlocked !", but I cannot go further.
If I connect the phone with a USB cable, wether he's "turned on" or turned off no led is blinking.
Does someone have a clue to fix this or has ever encountered this issue ?
Tanks in advance and do not hesitate to refer to an old post. I wil check (but found no same case).
Jérémie.
Click to expand...
Click to collapse
Take note of what version of recovery you have you at need to try a few different versions or your device has the dreded boot loop issue........
---------- Post added at 10:38 AM ---------- Previous post was at 10:22 AM ----------
stinka318 said:
Take note of what version of recovery you have you at need to try a few different versions or your device has the dreded boot loop issue........
Click to expand...
Click to collapse
This at help to........
https://forum.xda-developers.com/g4/help/installing-twrp-issue-t3606772
stinka318 said:
Take note of what version of recovery you have you at need to try a few different versions or your device has the dreded boot loop issue........
---------- Post added at 10:38 AM ---------- Previous post was at 10:22 AM ----------
This at help to........
https://forum.xda-developers.com/g4/help/installing-twrp-issue-t3606772
Click to expand...
Click to collapse
Not sure to understand but how can I try different versions of TWRP if I can't get to Recovery mode ?
Monkeypox95 said:
Not sure to understand but how can I try different versions of TWRP if I can't get to Recovery mode ?
Click to expand...
Click to collapse
What version did you flash.......
stinka318 said:
What version did you flash.......
Click to expand...
Click to collapse
I flashed this img twrp-3.0.2-1-h815.img
Monkeypox95 said:
I flashed this img twrp-3.0.2-1-h815.img
Click to expand...
Click to collapse
Is there another version that you can try found on Samsung device sometimes flashing a older version may work.....
stinka318 said:
Is there another version that you can try found on Samsung device sometimes flashing a older version may work.....
Click to expand...
Click to collapse
I really would like to try another version but how ? I can't even get to recovery mode... I'm stuck on the first LG logo.
Monkeypox95 said:
I really would like to try another version but how ? I can't even get to recovery mode... I'm stuck on the first LG logo.
Click to expand...
Click to collapse
If you can get it in to download mode use you laptop to flash recovery this is probably why it has failed.......remember Google s your friend.
stinka318 said:
If you can get it in to download mode use you laptop to flash recovery this is probably why it has failed.......remember Google s your friend.
Click to expand...
Click to collapse
Just to perfectly understand.
Are you advising me to flash my recovery with an older version via my laptop (I imagine via adb/fastboot) despite I can't even get my LG be recognized by my laptop ?
Will the adb/fastboot command be functional as the LG seems not to be recognized on the PC?
Monkeypox95 said:
Just to perfectly understand.
Are you advising me to flash my recovery with an older version via my laptop (I imagine via adb/fastboot) despite I can't even get my LG be recognized by my laptop ?
Will the adb/fastboot command be functional as the LG seems not to be recognized on the PC?
Click to expand...
Click to collapse
The best way to get your laptop I recognize your phone is to get LG up running then with the usb plugged n drop the battery out then put battery back in then close off LG up.
Then start it again and when it go's into download mode the pull usb and close off LG up Then plug it back in with dos prompt open............
stinka318 said:
The best way to get your laptop I recognize your phone is to get LG up running then with the usb plugged n drop the battery out then put battery back in then close off LG up.
Then start it again and when it go's into download mode the pull usb and close off LG up Then plug it back in with dos prompt open............
Click to expand...
Click to collapse
Thanks for your reply and your time. I didn't know this software "LG Up", I will give it a try this evening (in France ^^') and give you feedback then.
Monkeypox95 said:
Thanks for your reply and your time. I didn't know this software "LG Up", I will give it a try this evening (in France ^^') and give you feedback then.
Click to expand...
Click to collapse
LG UP had no effect on the phone.
However, now the phone seems to have 0% battery and when I try to boot it I get the graphics to plug the phone on a source of energy. Once I do that the front led is blinking in orange (I guess because I had less than 1 or 2% o battery) and now the front led is still lit on in orange. Is this a good news or I'm hoping for nothing.
Anyway tomorrow I will try to get it back to my retailer.
Does anyone succedeed to get it replaced by LG even if the bootloader is unlocked ?
Thanks.
After a little journey to the repair shop of my retailer everything seems to work correctly, for the moment, with LineageOS !
Thanks everyone for your help !
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
*additional informations*
here are the steps i followed:
1) unlocked bootloader succesfully
2) flashed official twrp
3) wiped EVERYTHING except sd ext
4) flashed this firmware
https://sourceforge.net/projects/xiaomi-firmware-updater/files/Developer/
5) flashed this rom
https://forum.xda-developers.com/re...ment/ota-resurrection-remix-os-6-0-0-t3777375
6) rebooted, dead
I noticed now that if i try to turn on the phone, the led blinks a few times
PROBLEM SOLVED:
the phone is alive again. Here is what I have done-
1) I opened the phone and tried the test point method, but I noticed that nothing changed in the way the phone was detected by my laptop. So, it's not crucial have "COM 7" in device manager.
Then I basically followed the steps suggested by @Destrangis in post #3
2- In MiFlash Choose CLEAN ALL and install this rom: http://bigota.d.miui.com/V9.2.7.0.NE...179eb04f38.tgz
3- Installed TWRP, WIPES and flash https://androidfilehost.com/?fid=5862345805528041092 and Magisk
4- Come back TWRP, WIPES and install your favorite rom.
Click to expand...
Click to collapse
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
EDL booting and flashing is your solution.
Now, only debatable is will you use EDL booting procedure which requires opening of the phone to short two contacts to be able to boot in EDL or You will use altered ADB which gives possibility to boot in EDL without case opening. This second option is somehow questionable but first, i think, if second option to enter EDL without opening is way to go!
---------- Post added at 07:37 PM ---------- Previous post was at 07:03 PM ----------
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
I hope this guide will help you!
lomax84 said:
Hi all,
after waiting 15 days, I have unlocked the bootloader, flashed twrp, firmware and rom, then rebooted.
the phone is dead ever since.
I can see it in device manager as "Qualcomm HS-USB QDLoader 9008 (COM10)", but I am not able to flash a rom through miflash.
any help is welcome
Click to expand...
Click to collapse
Hard brick. I went through it. Follow these steps: https://www.youtube.com/watch?v=lfkRHAW2iXI .
1- You have to activate the EDL mode.
2- In MiFlash Choose CLEAN ALL and install this rom: http://bigota.d.miui.com/V9.2.7.0.N...EK_20180406.0000.00_7.1_global_179eb04f38.tgz
3- Installed TWRP, WIPES and flash https://androidfilehost.com/?fid=5862345805528041092 and Magisk
4- Come back TWRP, WIPES and install your favorite rom. :good:
PD: If you see "COM7" in MIFLASH, go directly to step 2.
---------- Post added at 07:59 PM ---------- Previous post was at 07:55 PM ----------
Jehonan said:
EDL booting and flashing is your solution.
Now, only debatable is will you use EDL booting procedure which requires opening of the phone to short two contacts to be able to boot in EDL or You will use altered ADB which gives possibility to boot in EDL without case opening. This second option is somehow questionable but first, i think, if second option to enter EDL without opening is way to go!
---------- Post added at 07:37 PM ---------- Previous post was at 07:03 PM ----------
I hope this guide will help you!
Click to expand...
Click to collapse
The second opcion (ADB) doesnt work in RMN5.
what rom caused the brick?
devcon69 said:
what rom caused the brick?
Click to expand...
Click to collapse
info updated in the first post.
Is it crucial to have COM 7 port for EDL?
so, its been over a day now, have you fixed the problem?
t.hasan1 said:
so, its been over a day now, have you fixed the problem?
Click to expand...
Click to collapse
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
lomax84 said:
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
Click to expand...
Click to collapse
Whats did you do?
lomax84 said:
the phone is alive again.
I am in the process of flashing a custom rom again.
I'll update you when I'm done
Click to expand...
Click to collapse
what method you solved your brick phone ?
Give the method you do
Error: Cannot read hello packet. Why solved?
following...how did you solve it ? come on
mxilil said:
what method you solved your brick phone ?
Click to expand...
Click to collapse
masjiko said:
Give the method you do
Click to expand...
Click to collapse
please see first post
I tried to test point to give flash in the rom by Miflash, the pc recognizes my device in the COM port, when initiating the process it gives an error message: CAN NOT READ HELLO PACKET. Does anyone know how I can solve this problem? my device is simply dead because of that anti-rollback that Xiaomi implemented.
Diegosdias said:
I tried to test point to give flash in the rom by Miflash, the pc recognizes my device in the COM port, when initiating the process it gives an error message: CAN NOT READ HELLO PACKET. Does anyone know how I can solve this problem? my device is simply dead because of that anti-rollback that Xiaomi implemented.
Click to expand...
Click to collapse
Did you removed the battery?
devcon69 said:
Did you removed the battery?
Click to expand...
Click to collapse
yes...
Diegosdias said:
yes...
Click to expand...
Click to collapse
Try to use usb 2.0 ports.
Maybe edl mode has timed out. Press the power button for 20-30 seconds to power cycle the phone.
Or open it up and remove battery pin for a minute. Reconnect and try again.
devcon69 said:
Try to use usb 2.0 ports.
Maybe edl mode has timed out. Press the power button for 20-30 seconds to power cycle the phone.
Or open it up and remove battery pin for a minute. Reconnect and try again.
Click to expand...
Click to collapse
I already tried on usb ports 2 and 3, and it did not work. Holding the buttons for a long time did not solve either. I opened it to test point, removed the battery, but none of it makes the phone work. The problem is that at the time of fash in Miflash it gives the following error: CAN NOT READ HELLO POCKET. I do not know what this error is or what it is about?
lomax84 said:
please see first post
Click to expand...
Click to collapse
Did you recognize what caused the hard brick to your phone?
I think you followed the right steps, yet your phone got hard bricked, is it a firmware issue or RR rom issue?!
Ahmed_HM said:
Did you recognize what caused the hard brick to your phone?
I think you followed the right steps, yet your phone got hard bricked, is it a firmware issue or RR rom issue?!
Click to expand...
Click to collapse
By following his link to the firmware file on sourceforge you will see that he flashed a note4x firmware on his note5... So guess where the issue was...
Hi there,
I am having troubles with my phone (LMG810EAW) after uninstalling Magisk per app. The phone was Magisk-rooted and the bootloader is unlocked.
It constantly repeats rebooting, telling me that my bootloader is unlocked and then just showing the "No command"-Screen.
I do not have ADB-connection and the device is not recognized as USB device by Win10 at all.
None of the Vol+/Vol-/PWR combinations worked.
Except I can go into bootloader with VOL- & PWR and shortly releasing PWR at LG logo. But there it only shows the "Factory Reset" options.
Is there any option I can debrick my phone?
Thanks!
Best regards,
LeFish
I just got into fastboot-mode by fiddling arround with the phone!!!
Maybe this helps other to debrick their phone:
*The phone was plugged into USB of the computer.
*I pressed Vol- & PWR while on "No command"-screen
*The screen turned off
*Instantaniously, I released PWR, kept holding Vol-
Suddenly I was in fastboot-mode and the phone was recognized in CMD/fastboot.
Trying to get on from there - I'll keep reporting.
Best regards
LeFish
LeFish1 said:
I just got into fastboot-mode by fiddling arround with the phone!!!
Maybe this helps other to debrick their phone:
*The phone was plugged into USB of the computer.
*I pressed Vol- & PWR while on "No command"-screen
*The screen turned off
*Instantaniously, I released PWR, kept holding Vol-
Suddenly I was in fastboot-mode and the phone was recognized in CMD/fastboot.
Trying to get on from there - I'll keep reporting.
Best regards
LeFish
Click to expand...
Click to collapse
Just extract your boot IMG from your kdz and fastboot flash it. What's your reason for unrooting? If you want safety net to pass without magisk hide, you'll also need to relock bootloader
---------- Post added at 07:28 PM ---------- Previous post was at 07:27 PM ----------
antintin said:
Just extract your boot IMG from your kdz and fastboot flash it. What's your reason for unrooting? If you want safety net to pass without magisk hide, you'll also need to relock bootloader
Click to expand...
Click to collapse
Or just flash the magisk patched boot again for now
With holding Vol+ & Lock Button and then at the LG logo releasing the Lock Button, I managed to get into the Download-Mode.
I then installed LGup-LAB-Edition. Afterwards I could flash the stock 10r ROM. Everything is working now.
antintin said:
Just extract your boot IMG from your kdz and fastboot flash it. What's your reason for unrooting? If you want safety net to pass without magisk hide, you'll also need to relock bootloader
---------- Post added at 07:28 PM ---------- Previous post was at 07:27 PM ----------
Or just flash the magisk patched boot again for now
Click to expand...
Click to collapse
LeFish1 said:
I just got into fastboot-mode by fiddling arround with the phone!!!
Maybe this helps other to debrick their phone:
*The phone was plugged into USB of the computer.
*I pressed Vol- & PWR while on "No command"-screen
*The screen turned off
*Instantaniously, I released PWR, kept holding Vol-
Suddenly I was in fastboot-mode and the phone was recognized in CMD/fastboot.
Trying to get on from there - I'll keep reporting.
Best regards
LeFish
Click to expand...
Click to collapse
Sorry to bring up an old post, but what was on your screen when you got into fastboot?
Got the same problem with my LG V50 I got from China when I tried to remove Magisk as well, now I'm stuck in the no command boot loop. Tried all of the button combination and I'm still stuck "No Command" screen, tried to manually check adb devices to see if it was detected every time it rebooted but still no luck.
antintin said:
Just extract your boot IMG from your kdz and fastboot flash it. What's your reason for unrooting? If you want safety net to pass without magisk hide, you'll also need to relock bootloader
---------- Post added at 07:28 PM ---------- Previous post was at 07:27 PM ----------
Or just flash the magisk patched boot again for now
Click to expand...
Click to collapse
how is that done precisely ? please?
lateloads1 said:
how is that done precisely ? please?
Click to expand...
Click to collapse
and no reason other than im an idiot and hit uninstall after getting the phone back from a friend who "found" it with a newly broken screen and no battery or back, replaced screen and was getting " usb audio device not compatible with this device" when i would attach the second screen. I figured well , start from scratch cuz im an idiot and very green at rooting and flashing and this other dude raped my phone. That being said could educate me PLEASE on how to fastboot flash and would that be easier than Qfil or is that what your referring to....LOL. See? GREEEEEEn.
hello guys. i have a redmi note 8 (not 8t) and i used a custom rom android 10. then i want to test something and i flash the original rom with miflash without lock the bootloader. something happen after the flash and my phone is now on edl mode. can i save it? i try volume up down + power. i hear the restart sound on pc from reconection but still black screen.
demezakos said:
hello guys. i have a redmi note 8 (not 8t) and i used a custom rom android 10. then i want to test something and i flash the original rom with miflash without lock the bootloader. something happen after the flash and my phone is now on edl mode. can i save it? i try volume up down + power. i hear the restart sound on pc from reconection but still black screen.
Click to expand...
Click to collapse
go to the Xiaomi authorized service center
Baim alif said:
go to the Xiaomi authorized service center
Click to expand...
Click to collapse
there is nothing like this in greece
demezakos said:
there is nothing like this in greece
Click to expand...
Click to collapse
Have you ever tried reinstalling fastboot rom via mi flash tool?
---------- Post added at 01:03 AM ---------- Previous post was at 12:28 AM ----------
https://forum.xda-developers.com/redmi-note-8/help/redmi-note-8-firehose-authentication-t4031513
demezakos said:
hello guys. i have a redmi note 8 (not 8t) and i used a custom rom android 10. then i want to test something and i flash the original rom with miflash without lock the bootloader. something happen after the flash and my phone is now on edl mode. can i save it? i try volume up down + power. i hear the restart sound on pc from reconection but still black screen.
Click to expand...
Click to collapse
can you enter fastboot mode,
edl mode is no good its locked,
did you flashed correct version global, Eu etc
try this stupid steps too discharge battery or remove from phone and install again, now connect charger
Redmi 4A abdal said:
can you enter fastboot mode,
edl mode is no good its locked,
did you flashed correct version global, Eu etc
try this stupid steps too discharge battery or remove from phone and install again, now connect charger
Click to expand...
Click to collapse
well i discharge battery and this did not help. i put the correct global rom i did it some times before 2. i think i need some1 with edl account for reflash :/