{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
DISCLAIMER
I am not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed. Please do some research if you have any concerns about features included in this ROM before flashing it! YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
FEATURES
All J730 variants should be supported
Android 10
Arm64 with Treble support
3.18.140 kernel with f2fs support and many more
Enforcing build
VNDK-Full
The included vendor will let you boot any GSI a/b arm64
crDroid features
KNOWN BUGS
Other inherent bugs from AOSP, LineageOS or crDroid sources
Some 3rd camera apps have preview streched
CTS profile can fail in Magisk
Volte (it never will work)
SCREENSHOTS
https://crdroid.net/#screenshots
INSTALLATION
You need to have vendor partition in your device.
Wipe system, data (clean install recommended), vendor, dalvik&cache and cache
Flash rom zip (YOU DONT NEED TO FLASH ANY VENDOR, the vendor is inbuilt in the rom)
Flash GAPPS
Reboot
DOWNLOAD
Lastest build: 20/08/2020
GoogleDrive folder
GAPPS
Arm64 gapps
ROOT
Flash Magisk as usual
SUPPORT
Telegram group
SOURCES
My github org
CREDITS
Me, for infinite hours spent with this project
Special thanks to @Valera1978 for bringing this to the exynos7870
@followmsi for the upstream kernel commits
@stricted and 7870 dev team for his work in exynos source code
DONATIONS
I don't need them, I don't need coffees or beers. I really hate see here people with high end devices asking for donations, but you can still donate money to charity. Donate money or simply help people that is really needed. If you like this rom you can make me very happy just pushing THANKS
XDA:DevDB Information
crDroid 6.9, ROM for the Samsung Galaxy J7 (2017)
Contributors
Astrako
Source Code: https://github.com/crdroidandroid
ROM OS Version: Android 10
ROM Kernel: Linux 3.x
ROM Firmware Required: Oreo bootloader
Version Information
Status: Stable
Created 2020-06-19
Last Updated 2020-09-25
Reserved
New build is up! (19/06/2020)
Synced with lastest crDroid sources (6.7)
June security patch
Selinux enforcing
New H-KERNEL included, built enforcing and overclocked from lastest A6 Q sources
Updated a lot of proprietary stuff from lastest Samsung Q releases
Other minor changes and/or improvements
As usual, if you want to support my work, just push thanks button here and in first post of this thread.
Enjoy!
Great Job thanks my friend
Great job I have been using it for 2 days and it is perfect I love this rom
Thank you for the ROM, I am testing the ROM on SM-J730F and found one problem for now
First, thank you for the ROM, the problem that I have now is that the phone user interface(UI) is not showing when somebody is calling me, so I can't answer the call.
Does anybody have this problem?
Edit: It seems that now, the UI for answering call is showing now, I will continue to test the ROM.
Awesome ROM and vendor, works really great, chrome is working like a charm !
First Boot (Time)
Is it normal that the first boot takes several minutes? It's been about 10 minutes I've flashed it on my J7 Prime G610M, using Project TreBlue Vendor on my TWRP 3.2.3 and I was running Havoc OS 2.9 (Pie)?
Edit 1: After 15min waiting, stuck on CrDoird logo colorful, I am going to restart (vol down, home + power) to see if it starts and gets the Android setup.
Can somebody tell me how to take a NANDROID backup of this ROM properly?
I created vendor partition and installed this ROM using OrangeFox.
I also took full Backup(partitions selected: Boot, Cache, Recovery, System, System Image, Vendor, Vendor Image, Data, Modem, EFS) using OrangeFox.
I tried restoring the backup(selecting all partitions previously from backup), it did restore( i think phone rebooted while it was restoring the backup), but the ROM is not booting(it is stuck on crDROID logo)
So, how to take a proper backup of a crDROID ROM, or generally, of any treble ROM?
Edit: There is one approach to solve(partially) this problem: First, install crDROID as you would normally do(using the official guide on the first page on this thread), then don't restore the full backup, restore only the Data partition and crDROID will boot successfully.
Still, I wonder why full restore is not working, as the phone is rebooting while it is restoring(could be there a problem with the selected partition System Image and Vendor Image?)
what is main differences between havoc and crdroid?
tilkifatih said:
what is main differences between havoc and crdroid?
Click to expand...
Click to collapse
Havoc OS uses Project Treblue, while crDROID uses H-VENDOR(which is included in the current flashable ZIP of crDROID)
You can install either of them, it will be good.
I personally use crDROID, it is stable for now(everything that I tested is working: Camera, Wifi, Hotspot, SIM, Fingerprints).
My phone is J730F
---------- Post added at 01:13 PM ---------- Previous post was at 01:07 PM ----------
death.by.confusion said:
I created vendor partition and installed this ROM using OrangeFox.
....
Click to expand...
Click to collapse
Well, it seems the problem was in fact in System Image and Vendor Image
When you restore, don't restore System Image and Vendor Image. Only restore Boot, Recovery, Cache, Vendor, System, Data.
New build is up! (29/06/2020)
Synced with lastest crDroid sources (6.7)
Small changes in overlays
Now right device should appear in about menu
Other minor changes and/or improvements
As usual, if you want to support my work, just push thanks button here and in first post of this thread.
Enjoy!
Dirty flashing failed for me, but after a clean install it works perfectly.
Thanks!
Rom is wonderful but a problem. Always on does not appear despite playback and cannot connect the phone to the Samsung Smart TV
Sim card not detected
how I can fix this
Wow. Im surprised with this rom cant expect anyting. This rom is most stable than other gsi rom.
Its possible to turn this rom to permissive enforce? Il try lot of scrips but not working.
invalid zip file format?
thank you...
reason for stuck on logo is gapps 10
I hope you will still update this great ROM as i'm not a huge fan of oneui.
Keep the good work!
Is there a screen delay in the g610f
Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
/*
* I'm not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed (like it did for me...).
* Please do some research if you have any concerns about features included in the products you find here before flashing it!
* YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
* Your warranty will be void if you tamper with any part of your device / software.
* Same statement for XDA.
*/
LineageOS is a free, community built, aftermarket firmware distribution of Android 9 (Pie), which is designed to increase performance and reliability over stock Android for your device.
LineageOS is based on the Android Open Source Project with extra contributions from many people within the Android community. It can be used without any need to have any Google application installed. Linked below is a package that has come from another Android project that restore the Google parts. LineageOS does still include various hardware-specific code, which is also slowly being open-sourced anyway.
All the source code for LineageOS is available in the LineageOS Github repo. And if you would like to contribute to LineageOS, please visit out Gerrit Code Review.
What's working :
Boots
RIL (Calls, SMS, Data)
Fingerprint
Wi-Fi
Bluetooth
Camera
Audio
Sensors
Flash
LED
GPS
Known issues :
NFC
selinux permissive
Instructions :
Download the latest build , GApps and TWRP from downloads
Reboot to recovery
Flash the latest build and GApps
Reboot
Downloads :
Unofficial builds : Link
TWRP : Link (only this recovery can flash P roms , can flash all other zips too)
Gapps : Link
Credit :
Thanks to all testers who helped in testing
XDA:DevDB Information
LineageOS 16.0, ROM for the Asus ZenFone Max Pro M1
Contributors
SagarMakhar, Shivam Kumar Jha
Source Code: https://github.com/LineageOS/android_kernel_asus_sdm660
ROM OS Version: 9.x Pie
ROM Kernel: Linux 4.x
ROM Firmware Required: latest available
Based On: LineageOS
Version Information
Status: Stable
Beta Release Date: 2018-08-16
Created 2018-08-16
Last Updated 2019-07-21
reserved
reserved1
WeW
Good job dev
Thanks!
Great job, I enjoyed it
Nice work
Volte not working in any sim ?...or dual volte not working?
I never thought this device will have this much development all thanks to you sir!
Developers on fire??
Wew pru af:laugh:
murshi said:
Nice work
Volte not working in any sim ?...or dual volte not working?
Click to expand...
Click to collapse
Not working on any sim.
Can someone confirm, install .apk files is working ?
Because on AOSP is broken.
Thank you.
i see development in our community
Lineage 16 ? ?
Awesome dev, 1st Lineage 16 ROM out in town it seems...
Appreciate your efforts ??
@SagarMakhar, you maintain so many things for X00TD. I would suggest you focus with one or two: AOSP Pie and Lineage 16.
Otg works?
---------- Post added at 06:27 AM ---------- Previous post was at 06:24 AM ----------
gusbalaa said:
Can someone confirm, install .apk files is working ?
Because on AOSP is broken.
Thank you.
Click to expand...
Click to collapse
Installing .apk files works fine on AOSP P.
Mr.Ak said:
---------- Post added at 06:27 AM ---------- Previous post was at 06:24 AM ----------
Installing .apk files works fine on AOSP P.
Click to expand...
Click to collapse
How did you install .apk files on AOSP ?
My package installer always force close
Edit : Got it, i just search workaround.
lineage-os 9 rebooting into twrp recovery
ok, i might be the only one in this situation: i was running pie pr1 by @SagarMakhar. i installed the latest twrp v3.2.3-0 by @SagarMakhar, rebooted into recovery and made a full backup.
then, having read about flashing vendor.img, proceeded to wipe cache, dalvik-cache, data, system and vendor partitions. flashed the rom zip and vendor.img from pr1, wiped cache & dalvik-cache and rebooted. but, the device kept rebooting into twrp recovery immediately after reaching the home/lockscreen.
so, i wiped cache, dalvik-cache, data, system and vendor partitions and this time flashed only the rom zip and rebooted, but the device stayed at the bootanimation stage. although i badly wanted to run lineage-os 9 on x00td, i had to restore my nandroid backup (which went fine on the twrp v3.2.3-0 by @SagarMakhar) to make the device usable.
hope i get tips here to resolve the above issues and run lineage-os 9 on x00td. thanks in advance to SagarMakhar and others.
m0han said:
ok, i might be the only one in this situation: i was running pie pr1 by @SagarMakhar. i installed the latest twrp v3.2.3-0 by @SagarMakhar, rebooted into recovery and made a full backup.
then, having read about flashing vendor.img, proceeded to wipe cache, dalvik-cache, data, system and vendor partitions. flashed the rom zip and vendor.img from pr1, wiped cache & dalvik-cache and rebooted. but, the device kept rebooting into twrp recovery immediately after reaching the home/lockscreen.
so, i wiped cache, dalvik-cache, data, system and vendor partitions and this time flashed only the rom zip and rebooted, but the device stayed at the bootanimation stage. although i badly wanted to run lineage-os 9 on x00td, i had to restore my nandroid backup (which went fine on the twrp v3.2.3-0 by @SagarMakhar) to make the device usable.
hope i get tips here to resolve the above issues and run lineage-os 9 on x00td. thanks in advance to SagarMakhar and others.
Click to expand...
Click to collapse
I too faced the same issue with TWRP. The workaround that worked for me is that when you have flashed the zips after wipe, dont reboot using the menu given in TWRP. Just press the power button until it reboots.
UPDATE 20180817
Changelogs :
- fixed Music Player crash
- Fixed case where device reboots to recovery after flashing custom zips ( disabled rescue party )
Download : https://androidfilehost.com/?fid=1322778262903982435
m0han said:
lineage-os 9 rebooting into twrp recovery
Click to expand...
Click to collapse
fixed in latest build
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
DISCLAIMER
I am not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed. Please do some research if you have any concerns about features included in this ROM before flashing it! YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
FEATURES
J710X supported
Built with lastest OrangeFox sources and my own device tree
Vendor partition supported
f2fs supported
and many more!
INSTALLATION
Flash OrangeFox recovery zip in your current recovery
DOWNLOAD
Lastest build: 04/08/2020
OrangeFox downloads
SUPPORT
Telegram group
OrangeFox support group
SOURCES
https://gitlab.com/OrangeFox
CREDITS
Me, for infinite hours spent with this project
Special thanks to @Valera1978
@stricted and 7870 dev team for his work in exynos source code
OrangeFox Recovery team
DONATIONS
I don't need them, I don't need coffees or beers. I really hate see here people with high end devices asking for donations, but you can still donate money to charity. Donate money or simply help people that is really needed. If you like this rom you can make me very happy just pushing THANKS
XDA:DevDB Information
OrangeFox Recovery Project, ROM for the Samsung Galaxy J7
Contributors
Astrako
Source Code: https://gitlab.com/OrangeFox
ROM OS Version: 9.x Pie
ROM Kernel: Linux 3.x
Version Information
Status: Beta
Current Stable Version: 11.0
Stable Release Date: 2020-08-04
Current Beta Version: 10.1
Beta Release Date: 2020-03-09
Created 2020-03-09
Last Updated 2020-08-04
reserved
Since I don't have this phone and I can't test for myself, I suggest to flash it having Odin and TWRP at hand, just in case. It has been tested for other users tho, and it worked fine.
THANK YOU SO MUCH FOR THE BRINGING ORANGEFOX RECOVERY FOR OUR DEVICE. YOU'RE AWESOME DEVELOPER!
I finally tested it in first time. I highly recommend it!
And a question, is this works on treble?
The OrangeFox Recovery is flashed successfully on J7 2016 (SM-J710FQ)
TRalperenTR said:
And a question, is this works on treble?
Click to expand...
Click to collapse
Thanks for your feedback, appreciated.
Yeah it supports vendor partition so treble too.
I have never heard of the OrangeFox Recovery Project but I might try it out since I appreciate all the development given into it and I generally like the overall design. I'm just a little scared that I might lose all my data.
EDIT: Decided to install it. Looks really nice. Great work developer. The only issue I have is that it says my ROM isn't Treble when it clearly is and that it spends like 10 seconds on the splash screen rather than like 3 seconds when I try to go into recovery. But overall I'd say that this recovery is very well made, has a beautiful and easy to navigate UI, tons of features like Magisk Manager and the App Manager which I know I'll look into at some point.
J710FN don`t have vendor partition. Do I need to flash vendor before use treble with OrangeFox Recovery?
ekobaltika said:
J710FN don`t have vendor partition. Do I need to flash vendor before use treble with OrangeFox Recovery?
Click to expand...
Click to collapse
You can use it without vendor partition. No problem at all.
Great recovery. Loved the advanced UI and amazingly I can backup EFS partition which I previously couldn't do on TWRP. Its awesome that it can extract compressed files (useful for those who forgot to extract GSI before flashing lol) and it can edit text files because the recovery has nano (a CLI text editor that's popular on Linux). Lots of customizability which I wouldn't expect a recovery to have. And for those who wants to make sure no one picks up your phone and factory reset it for laughs, you can apply security for your recovery (password etc).
This recovery might take a little longer to boot as compared to other recoveries but its definitely worth trying.
Hi again. The OrangeFox is very beautiful recovery I've ever had. I have the some issues in this build.
Bugs:
- The OrangeFox recovery launching time is longer than TWRP (10-15 seconds on bootlogo, 6-8 seconds on recovery bootlogo)
- The Power Off button doesn't power off my device lol (It's just rebooting back)
- The "/vendor" partition isn't hidden in non-treble device. (It's hidden on TWRP. Idk why. I don't even using non-treble rom. Maybe the creator of OrangeFox's fault?)
That's all for now. Thank you dev for building this for j7 2016.
It is a very good recovery. It solved my issue of internal storage unable to mount on twrp.
It still need some improvements. Bit overall it is a good one. I m waiting for future updates.
Works great on SM-710FN.
Thank you so much!
Is there a new update coming?
For Delete
New build is up! (28/05/2020)
- Synced with lastest OrangeFox sources
- Built with A600FNXXU5CTB9 Q sources
As usual, if you want to support my work, just push thanks button here and in first post of this thread.
Enjoy!
Tnx alot for your awesome work.......
Thank you for your work, good sir!
One drive download link is down
Thanks for your great work....
I have installed some of your treble rom with this orangefox. everything fine but when i try to restore the backup rom, process on restoring always fail on restore system image. can you explain this? when i try restore with TWRP 3.4 it goes well
New build is up! (04/08/2020)
- Updated to Official R11.0 release
- Synced with lastest OrangeFox sources
- Other minor changes
As usual, if you want to support my work, just push thanks button here and in first post of this thread.
Enjoy!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
DISCLAIMER
I am not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed. Please do some research if you have any concerns about features included in this ROM before flashing it! YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you
Since I dont have EVERY 7870, this project is open to contributions, so feel free to suggest fixes, improvements or any other thing that could be helpful.
FEATURES
Arm64 vendor ported from J6, A7 2018 and S20
A320X, G610X, J530X, J600X, J701X, J710X, J730X are supported
Android 10 A/B ARM64 supported. Android 11 ready.
H-KERNEL included (3.18.140 kernel compiled from A600FNXXU5CTB9 sources. Built permissive and overclocked. F2fs supported)
AresKernel by @SPARTANICUS supported and recommended
And many more!
KNOWN BUGS
Remember that some bugs could come from GSI side and not from vendor
We haven't tested EVERY 7870 out there, so could be possible that some variants has specific and unknown bugs, or even not booting
Always provide logs and dmesg if you want to report bugs
Common bugs: offlice charging, screen unlock takes a while after a reboot, camera preview streched for some variants or apps. BT calls is a common bug too for some devices. Stock camera flash can be unstable, use footej
A320X: echo in calls
G610X: sometimes, screen delay when coming on, camera flash?
J530X: ?
J600X: NFC could be broken for some variants
J701X: front camera flash
J710X: NFC could be broken for some variants. Audio has a delay for the NM
J730X: ?
You tell me
DOWNLOAD
Current version: 1.0 (16/06/2020)
GoogleDrive folder
Mega folder
md5: 30620c555e13eaecca42ddda56ddec58
INSTALLATION
Vendor partition is required
HIGHLY RECOMMENDED TO USE AN UPDATED RECOVERY. Check my OrangeFox or SHRP builds.
Wipe system, data (clean install mandatory), vendor, dalvik&cache and cache
Flash an Android 10 A/B ARM64 system GSI image
Flash H-VENDOR zip
Reboot
WALLPAPERS
https://imgur.com/a/El75gHV. Thanks to @SaiFurR
ROOT
Flash stable Magisk
SUPPORT
Telegram group
CREDITS
Me, for infinite hours spent with this project
Special thanks to @ananjaser1211, @SPARTANICUS and @Valera1978, and everyone that has contributed to the 7870 development
Huge thanks also to my testers, without them this coundn't have been possible
Thanks to @Kique119, because he pushed me to start this project
And finally thanks to @SaiFurR for the banner and supporting me in every project
DONATIONS
I don't need them, I don't need coffees or beers. I really hate see here people with high end devices asking for donations, but you can still donate money to charity. Donate money or simply help people that is really needed. If you like this project you can make me very happy just pushing THANKS
XDA:DevDB Information
H-VENDOR, ROM for the Samsung Galaxy J7 (2017)
Contributors
Astrako
Source Code: https://gitlab.com/android_samsung_universal7870/common/android_kernel_samsung_exynos7870/-/tree/oneui_q
ROM OS Version: Android 10
ROM Kernel: Linux 3.x
Version Information
Status: Stable
Current Stable Version: 1.0
Created 2020-06-16
Last Updated 2020-10-06
Reserved
Thanx for great work
thanks dude.
Great Job
In J730g only offline charging bugg
Thanks
Can i flash stable version of magisk when i use this vendor?
System UI restarts when turning on quick tile settings (quick bar).
Great! Something to play around with. Thanks!
hacker812c said:
Great Job
In J730g only offline charging bugg
Thanks
Click to expand...
Click to collapse
Same here
Astrako said:
Reserved
Click to expand...
Click to collapse
Testing and repporting
1. vendor stable and fast
2. using other vendor Corvus os fail boot
3. using H vendor Corvus os 9.0 boot perfectly
No news updates ?
Great Job
is face unlock working?
hacker812c said:
Great Job
In J730g only offline charging bugg
Thanks
Click to expand...
Click to collapse
So will my phone boot up immediately when I charge it ?
Also does USB tethering (network of phone share to computer ) work?
Great vendor j7 the.best vendor for me
I recomend this vendor
Can you flash it over an existing vendor without losing your data?
lucas_54 said:
Can you flash it over an existing vendor without losing your data?
Click to expand...
Click to collapse
Flash over no delete data
The only way i've made it work is to flash H-Vendor + Ares Kernel RC1 + Magisk 20.4 phhusson.
All the other solutions lead to being stuck on LineageOS boot animation.
Maybe i need to format the Vendor partition first?
someone pls explain what is h-vendor? I need to install lineage GSI, I need H-vendor or is optional?
xiaomiyaaa said:
someone pls explain what is h-vendor? I need to install lineage GSI, I need H-vendor or is optional?
Click to expand...
Click to collapse
You need
Twrp and magisk
Install create vendor to
Vendor partition
Lineage for j7 have orher vendor
After create vendor you install
Some roms in your j7
hacker812c said:
Install create vendor to
Vendor partition
Click to expand...
Click to collapse
how do i create vendor?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
brought to you by the
Code:
/*
* I'm not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed (like it did for me...).
* Please do some research if you have any concerns about features included in the products you find here before flashing it!
* YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
* Your warranty will be void if you tamper with any part of your device / software.
* Same statement for XDA.
*/
About /e/:
/e/ is an a mobile ecosystem (ROM + onlines services) that:
is open source
is pro-privacy
is compatible with most existing Android applications
cares about usability
is as far as possible freed from shackles by Google and OEMs
already exists!
It’s the alternative to the Apple/Google duopoly on the smartphone.
... so again and just to be clear: /e/ is not just a ROM, it is more a complete privacy ecosystem and consists of:
an installable mobile operating system for smartphones, which is forked from Android and strongly “ungoogled”
a set of sorted and improved default open source applications
various online services that are linked to the mobile operating system, such as: a meta search engine for the web, drive (with synchronization), mail, calendar, notes, tasks.
Features:
Based on the stable Lineage OS 17.1
microG fully pre-installed with Signature Spoofing in restricted mode!
All features described on the /e/ page: What is e
All features and fixes of our LOS 17.1 builds (Whatawurst team).
No OTA suppport for now.
What works:
Same as Whatawurst team LOS 17.1 build
Known issues:
/e/ Q is still in development stage (still, stable enough for a daily driver with no bugs). So you may still see one or two calls to Google servers until the Q branch is official.
You tell me
Same as Whatawurst team LOS 17.1 build
SECURITY ADVICE
Don't flash Magisk modules or anything else which sets SELinux to permissive or you open your device for malware!
Do not flash Multi Disabler on this ROM!
Requirements:
Latest TWRP build.
Do a full Nandroid backup before doing anything!
Installation:
If this is your first time flashing a rom, or not coming from @modpunk LOS 17.1 build, please follow the same steps than their detailed installation process
Otherwise:
Full clean install is highly recommended. DO NOT REPORT ISSUES when you have skipped that step!
Flash /e/
Optional (if you want root): Flash Magisk
Flashing OpenGapps ????? NO No no! you don't want that on a google-free phone! /e/ contains everything you need to live without Google! So flashing OpenGapps on /e/ is like using a bit more secure LOS but that's not the point of /e/. Either try without or go with LOS (imho).
Boot it (will take a bit on first boot!!! be patient!)
Enjoy the most easy way to have a privacy focused and google-free phone!
Download:
Get your builds from my GoogleDrive (I know, it's ironical)
S10e (beyond0lte, SM-G970F)
S10 (beyond1lte, SM-G973F)
S10+ (beyond2lte, SM-G975F)
Note:
Builds are updated as soon as possible. There is no build cycle.
Information pertaining to your device is displayed accordingly.
The current build is the latest for your device.
Changelogs:
Check /e/, LineageOS or whatawurst team changelogs. I build straight from sources
Support:
/e/ Support Telegram Channel
Credits:
LineageOS (the base of /e/)
The /e/ foundation and all related devs making this experience possible!
the whatawurst team for their kernel, device and vendor sources.
The Exynos9820 Team
and more..
Sources:
How to build /e/
Local_manifest ==> See attachments
XDAevDB Information
beyond0lte_eos-Q_custom, ROM for the Samsung Galaxy S10e Exynos
Contributors:
Whatawurst team (modpunk, derf elot,Linux4), steadfasterX, Exynos9820 Team
Source Code:
https://github.com/whatawurst/
ROM OS Version: Android 10
ROM Kernel: Linux 4.x
ROM Firmware Required: XXS9DTI8
Based On: LineageOS
Version Information
Status: Stable
Stable Release Date: 2020-11-25
Please note that I don't own the device and am not a dev. Just an Android enthusiast who knows how to build ROM's based on existing sources and loves privacy.
I built this version for someone I know who's about to buy a S10e and wants /e/ on it.
Please give me your feedback. This will be highly appreciated.
Changelog 11/25/2020:
Updating builds based on modpunk's LOS 17.1 V1.3
Changing the way proprietary blobs are integrated into the zip (hopefully fix the robotic voice on bluetooth calls)
S10e build uploaded on 11/25/2020
S10/S10+ uploaded on 11/26/2020
Changelog 11/08/2020:
Re-uploaded builds, manually replaced the vendor files in the .zip using the official from Whatawurst LOS builds as it seems my build method did not populate properly vendor.
Another one
Hi !
It's awesome but for S10 I guess "soon" doesn't mean later today ?
florek_18 said:
Hi !
It's awesome but for S10 I guess "soon" doesn't mean later today ?
Click to expand...
Click to collapse
S10 at 96% !!!
Please note I am not a dev, just an Android enthusiast who knows how to build based on existing sources and loves privacy.
S10 (beyond1lte) build uploaded!
Again: awesome !!!
Will test it tonight I was interested in this OS for some time already.
florek_18 said:
Again: awesome !!!
Will test it tonight I was interested in this OS for some time already.
Click to expand...
Click to collapse
Keep us posted.
I guess format data is required? With regular wipe data, cache, dalvik and system it's stuck on boot logo (powered by android i mean).
florek_18 said:
I guess format data is required? With regular wipe data, cache, dalvik and system it's stuck on boot logo (powered by android i mean).
Click to expand...
Click to collapse
Are you encrypted? While for the bootloader version and firmware, please refer to the thread below; I used their sources:
https://forum.xda-developers.com/ga...rom-lineageos-17-1-beta0-s10e-update-t4076585
As I told previously, I am not a dev unfortunately. I just build using existing sources proven to work.
edit: Seems yes, format data is required. This is mentioned in their FAQ.
Install LinageOS
copy the ROM ZIP file an external SD card
Boot into the recovery
Wipe cache + dalvik (wipe->advanced and select cache + dalvik)
Format data (wipe->format data, use the dedicated button, wipe->advanced does not work)
Flash the ROM (install -> select storage -> micro SD card and select the .zip file)
Optional: Flash GAPPS (e.g. OpenGAPPS)
Reboot to system
I also see that on my builds, the vendor.img is much smaller than in their builds.
I'll ask them.
Yeah, thats what I thought as i flashed LoS from modpunk before. Anyway, doing complete backup and will try again.
florek_18 said:
Yeah, thats what I thought as i flashed LoS from modpunk before. Anyway, doing complete backup and will try again.
Click to expand...
Click to collapse
I took modpunk sources to build /e/. But I fear my vendor.img is missing some things (my vendor.img are about 17Mo while his are up to 120Mo).
Need to figure out what and why.
Don't know if it could be doable to repack the /e/ zip with the vendor files from modpunk builds zips.
I don't know the S10.
Gotta sleep. Good luck and keep in touch tomorrow.
So i just found out copying all the vendor files from modpunks lineage os to the /e/ zip with 7zip actualy works so il keep updated if its stable
catormeme said:
So i just found out copying all the vendor files from modpunks lineage os to the /e/ zip with 7zip actualy works so il keep updated if its stable
Click to expand...
Click to collapse
Cool to know thanks.
I'll do for all the other files then.
What device are you running on?
Uploading zips with replaced vendor files now. Should be available in a few mn.
Please test and let me know. I'd like to see what device you are running on as well thanks.
@catormeme
Did you have to format data to boot?
Anghirrim said:
@catormeme
Did you have to format data to boot?
Click to expand...
Click to collapse
yes, i formated data before and after installing also did the same with cache and dalvic
catormeme said:
yes, i formated data before and after installing also did the same with cache and dalvic
Click to expand...
Click to collapse
What device?
Is it possible to upgrade from modpunks lineageos 17.1 without format data partition?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
brought to you by the
Code:
/*
* I'm not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed (like it did for me...).
* Please do some research if you have any concerns about features included in the products you find here before flashing it!
* YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
* Your warranty will be void if you tamper with any part of your device / software.
* Same statement for XDA.
*/
About /e/:
/e/ is an a mobile ecosystem (ROM + onlines services) that:
is open source
is pro-privacy
is compatible with most existing Android applications
cares about usability
is as far as possible freed from shackles by Google and OEMs
already exists!
It’s the alternative to the Apple/Google duopoly on the smartphone.
... so again and just to be clear: /e/ is not just a ROM, it is more a complete privacy ecosystem and consists of:
an installable mobile operating system for smartphones, which is forked from Android and strongly “ungoogled”
a set of sorted and improved default open source applications
various online services that are linked to the mobile operating system, such as: a meta search engine for the web, drive (with synchronization), mail, calendar, notes, tasks.
Features:
Based on the stable Lineage OS 17.1
microG fully pre-installed with Signature Spoofing in restricted mode!
All features described on the /e/ page: What is e
All features and fixes of our LOS 17.1 builds (Whatawurst team).
No OTA suppport for now.
What works:
Same as Whatawurst team LOS 17.1 build
Known issues:
/e/ Q is still in development stage (still, stable enough for a daily driver with no bugs). So you may still see one or two calls to Google servers until the Q branch is official.
You tell me
Same as Whatawurst team LOS 17.1 build
SECURITY ADVICE
Don't flash Magisk modules or anything else which sets SELinux to permissive or you open your device for malware!
Do not flash Multi Disabler on this ROM!
Requirements:
Latest TWRP build.
Do a full Nandroid backup before doing anything!
Installation:
If this is your first time flashing a rom, or not coming from @modpunk LOS 17.1 build, please follow the same steps than their detailed installation process
Otherwise:
Full clean install is highly recommended. DO NOT REPORT ISSUES when you have skipped that step!
Flash /e/
Optional (if you want root): Flash Magisk
Flashing OpenGapps ????? NO No no! you don't want that on a google-free phone! /e/ contains everything you need to live without Google! So flashing OpenGapps on /e/ is like using a bit more secure LOS but that's not the point of /e/. Either try without or go with LOS (imho).
Boot it (will take a bit on first boot!!! be patient!)
Enjoy the most easy way to have a privacy focused and google-free phone!
Download:
Get your builds from my GoogleDrive (I know, it's ironical)
S10e (beyond0lte, SM-G970F)
S10 (beyond1lte, SM-G973F)
S10+ (beyond2lte, SM-G975F)
Note:
Builds are updated as soon as possible. There is no build cycle.
Information pertaining to your device is displayed accordingly.
The current build is the latest for your device.
Changelogs:
Check /e/, LineageOS or whatawurst team changelogs. I build straight from sources
Support:
/e/ Support Telegram Channel
Credits:
LineageOS (the base of /e/)
The /e/ foundation and all related devs making this experience possible!
the whatawurst team for their kernel, device and vendor sources.
The Exynos9820 Team
and more..
Sources:
How to build /e/
Local_manifest ==> See attachments
XDAevDB Information
beyond0lte_eos-Q_custom, ROM for the Samsung Galaxy S10e Exynos
Contributors:
Whatawurst team (modpunk, derf elot,Linux4), steadfasterX, Exynos9820 Team
Source Code:
https://github.com/whatawurst/
ROM OS Version: Android 10
ROM Kernel: Linux 4.x
ROM Firmware Required: XXS9DTI8
Based On: LineageOS
Version Information
Status: Stable
Stable Release Date: 2020-11-25
Please note that I don't own the device and am not a dev. Just an Android enthusiast who knows how to build ROM's based on existing sources and loves privacy.
I built this version for someone I know who's about to buy a S10e and wants /e/ on it.
Please give me your feedback. This will be highly appreciated.
Changelog 11/25/2020:
Updating builds based on modpunk's LOS 17.1 V1.3
Changing the way proprietary blobs are integrated into the zip (hopefully fix the robotic voice on bluetooth calls)
S10e build uploaded on 11/25/2020
S10/S10+ uploaded on 11/26/2020
Changelog 11/08/2020:
Re-uploaded builds, manually replaced the vendor files in the .zip using the official from Whatawurst LOS builds as it seems my build method did not populate properly vendor.
Another one
Hi !
It's awesome but for S10 I guess "soon" doesn't mean later today ?
florek_18 said:
Hi !
It's awesome but for S10 I guess "soon" doesn't mean later today ?
Click to expand...
Click to collapse
S10 at 96% !!!
Please note I am not a dev, just an Android enthusiast who knows how to build based on existing sources and loves privacy.
S10 (beyond1lte) build uploaded!
Again: awesome !!!
Will test it tonight I was interested in this OS for some time already.
florek_18 said:
Again: awesome !!!
Will test it tonight I was interested in this OS for some time already.
Click to expand...
Click to collapse
Keep us posted.
I guess format data is required? With regular wipe data, cache, dalvik and system it's stuck on boot logo (powered by android i mean).
florek_18 said:
I guess format data is required? With regular wipe data, cache, dalvik and system it's stuck on boot logo (powered by android i mean).
Click to expand...
Click to collapse
Are you encrypted? While for the bootloader version and firmware, please refer to the thread below; I used their sources:
https://forum.xda-developers.com/ga...rom-lineageos-17-1-beta0-s10e-update-t4076585
As I told previously, I am not a dev unfortunately. I just build using existing sources proven to work.
edit: Seems yes, format data is required. This is mentioned in their FAQ.
Install LinageOS
copy the ROM ZIP file an external SD card
Boot into the recovery
Wipe cache + dalvik (wipe->advanced and select cache + dalvik)
Format data (wipe->format data, use the dedicated button, wipe->advanced does not work)
Flash the ROM (install -> select storage -> micro SD card and select the .zip file)
Optional: Flash GAPPS (e.g. OpenGAPPS)
Reboot to system
I also see that on my builds, the vendor.img is much smaller than in their builds.
I'll ask them.
Yeah, thats what I thought as i flashed LoS from modpunk before. Anyway, doing complete backup and will try again.
florek_18 said:
Yeah, thats what I thought as i flashed LoS from modpunk before. Anyway, doing complete backup and will try again.
Click to expand...
Click to collapse
I took modpunk sources to build /e/. But I fear my vendor.img is missing some things (my vendor.img are about 17Mo while his are up to 120Mo).
Need to figure out what and why.
Don't know if it could be doable to repack the /e/ zip with the vendor files from modpunk builds zips.
I don't know the S10.
Gotta sleep. Good luck and keep in touch tomorrow.
So i just found out copying all the vendor files from modpunks lineage os to the /e/ zip with 7zip actualy works so il keep updated if its stable
catormeme said:
So i just found out copying all the vendor files from modpunks lineage os to the /e/ zip with 7zip actualy works so il keep updated if its stable
Click to expand...
Click to collapse
Cool to know thanks.
I'll do for all the other files then.
What device are you running on?
Uploading zips with replaced vendor files now. Should be available in a few mn.
Please test and let me know. I'd like to see what device you are running on as well thanks.
@catormeme
Did you have to format data to boot?
Anghirrim said:
@catormeme
Did you have to format data to boot?
Click to expand...
Click to collapse
yes, i formated data before and after installing also did the same with cache and dalvic
catormeme said:
yes, i formated data before and after installing also did the same with cache and dalvic
Click to expand...
Click to collapse
What device?
Is it possible to upgrade from modpunks lineageos 17.1 without format data partition?