Hi,
so I am kinda new to this and wanted to upgrade to 5.1.1 below is the initial information.
Its a Roadmaster AN-111 GMC (if it matters)
It was MTCB - KSP 2.86
upgraded to MTCB KSP 2.89(KSP_11-28-2016_1.99_dmcu.img)
Firmware was 4.4.4_11032016
I installed the KLD - 2.1.1 december update
now the system boots up but does not show any display, if i plug in a USB it starts to play songs. All hardware button BEEP when i click so does the buttons on steering. I
I can go into recovery but I continuously receive the no sd card - cant post a picture yet
any chance of recovery please?
Hello,
Are you sure the MCU upgrade you did was to KSP 2.89 ? The filename you gave says something else: KSP_11-28-2016_1.99_dmcu.img (notice the 1.99 in the filename).
That would mean you did a MCU downgrade. Try flashing the MCU back again (i have KSP mcu too, not sure which version, i may be able to help you).
Regarding 5.1.1 update, i have the same behavior. I do not see the "desktop" with all the icons, but i see toast messages, popups, the "preparing to shutdown" window, so, maybe display driver problem ?
Hi
I recently returned my PX5 MTCD unit (purchased through Amazon) as it kept switching the speedo to kph. Since I've returned it Dasaita have sent me a sendspace link to a 500mb fix which they reckon will stop the issue. I do remember seeing others with the same problem so thought I'd share here.
This was for a Peugeot 208 UK 2015 incidentally. I'd previously tried Canbus updates, new ROM's and every Canbus setting with no luck.
If this does fix the issue please let me know as I'll probably repurchase the head unit. I've re-uploaded the file to Google Drive as i have unlimited storage there.
Here you go for the file:
Update steps：
1. Check whether the wiring is plugged rightly and the canbus is plugged in rightly.
2. Prepare a USB flash drive，format the usb, only put the CANBUS.UPDE file in the folder into the root directory of the USB flash drive.
3. Insert the USB flash drive into the navigation USB interface and check if the navigation correctly reads the USB flash drive data.
4. Enter the system settings, click the factory settings, enter the password: canupdates
5. Navigation prompt download, wait for the prompt download to complete or the machine to restart, the upgrade step is completed, then unplug the U disk
Special attention: The upgrade process is about 20 minutes, and our device is forbidden to power off during the period, otherwise the canbus will be scrapped directly!!!
EDIT: Ah, I'm new so I can't post links. If anyone wants a copy of the Canbus file, please ping me a message and I'll send over.
jamesbruton said:
Hi
I recently returned my PX5 MTCD unit (purchased through Amazon) as it kept switching the speedo to kph. Since I've returned it Dasaita have sent me a sendspace link to a 500mb fix which they reckon will stop the issue. I do remember seeing others with the same problem so thought I'd share here.
This was for a Peugeot 208 UK 2015 incidentally. I'd previously tried Canbus updates, new ROM's and every Canbus setting with no luck.
If this does fix the issue please let me know as I'll probably repurchase the head unit. I've re-uploaded the file to Google Drive as i have unlimited storage there.
Here you go for the file:
Update steps：
1. Check whether the wiring is plugged rightly and the canbus is plugged in rightly.
2. Prepare a USB flash drive，format the usb, only put the CANBUS.UPDE file in the folder into the root directory of the USB flash drive.
3. Insert the USB flash drive into the navigation USB interface and check if the navigation correctly reads the USB flash drive data.
4. Enter the system settings, click the factory settings, enter the password: canupdates
5. Navigation prompt download, wait for the prompt download to complete or the machine to restart, the upgrade step is completed, then unplug the U disk
Special attention: The upgrade process is about 20 minutes, and our device is forbidden to power off during the period, otherwise the canbus will be scrapped directly!!!
EDIT: Ah, I'm new so I can't post links. If anyone wants a copy of the Canbus file, please ping me a message and I'll send over.
Click to expand...
Click to collapse
The links send me from @jamesbruton
https://drive.google.com/open?...W_XA1nZfRiNqLyjwALBL1Q6hGi8Qot
Here's the original file:
Hi, James
Here you go for the file:
https://www.sendspace.com/file/ka4s6h
Update steps：
1. Check whether the wiring is plugged rightly and the canbus is plugged in rightly.
2. Prepare a USB flash drive，format the usb, only put the CANBUS.UPDE file in the folder into the root directory of the USB flash drive.
3. Insert the USB flash drive into the navigation USB interface and check if the navigation correctly reads the USB flash drive data.
4. Enter the system settings, click the factory settings, enter the password: canupdates
5. Navigation prompt download, wait for the prompt download to complete or the machine to restart, the upgrade step is completed, then unplug the U disk
Special attention: The upgrade process is about 20 minutes, and our device is forbidden to power off during the period, otherwise the canbus will be scrapped directly!!!
Enviado desde mi ONEPLUS A5010 mediante Tapatalk
I've got a px5 unit in a 2013 mini Cooper and it is working well except it seems to have slowed down the mph update speed on the main factory speedo. When I set cruise control, the "cruise set speed" display shows at kph instead of MPH, after cruise speed it set, the dash display switches back to showing mph. Lol.
Tried contacting hifimax to resolve but they haven't been friendly about it.
Hello.
Help me please! Diligently!
My unit is Px5 8xA53 1.5G 4G
MCU: MTCE_MX_V2.88b_1
Android: px5-userdebug 8.0.0 OPR5.170623.007 eng.hct.20180627.151600 test-keys
Ford Fiesta 2015
Unfortunately, I could not program the buttons in the "Factory settings" (nothing was visible there) and I decided to update CANBUS.UPDE but immediately he dropped the error "fail !!! 0x0e" and after the reset canbus does not work
was the canbus box damaged? Can I resuscitate this?
I disconnected the battery, reset everything to the factory settings in recovery, I have read the new MTCE ... nothing helped ... please help me quickly because the equipment is new and I do not know whether to send it to the seller ...
or maybe it hurt the new mcte and deleted the canbus settings? I do not know, help ...
Yes it does work. It is because of my pestering of Dasaita the file exists in the firstplace. I have shared the details in other posts.
The actual file is nowhere near 500mb - the file includes a number of pointless video clips. The actual required file is a few kb. Takes a few minutes to install.
I have a 2016 Peugeot 208 GT Line.
Dasaita were very helpful in working with me to provide the fix. The only remaining issue is that the fuel consumption program still only shows metric data, no matter what settings you give it.
aggiornamento can bus
can have can bus update
[email protected]
segu45 said:
The links send me from @jamesbruton
https://drive.google.com/open?...W_XA1nZfRiNqLyjwALBL1Q6hGi8Qot
Here's the original file:
Hi, James
Here you go for the file:
man please repost this file: https://www.sendspace.com/file/ka4s6h
Update steps：
1. Check whether the wiring is plugged rightly and the canbus is plugged in rightly.
2. Prepare a USB flash drive，format the usb, only put the CANBUS.UPDE file in the folder into the root directory of the USB flash drive.
3. Insert the USB flash drive into the navigation USB interface and check if the navigation correctly reads the USB flash drive data.
4. Enter the system settings, click the factory settings, enter the password: canupdates
5. Navigation prompt download, wait for the prompt download to complete or the machine to restart, the upgrade step is completed, then unplug the U disk
Special attention: The upgrade process is about 20 minutes, and our device is forbidden to power off during the period, otherwise the canbus will be scrapped directly!!!
Enviado desde mi ONEPLUS A5010 mediante Tapatalk
Click to expand...
Click to collapse
//MTCE_LM not LS, can't edit the title anymore.
Changed customer version from 1 to 3 and after reboot, i have no screen and no buttons working.
Only after car power is cut off (5-10min), the unit comes back but shuts down within 10-15 sec, not enough to quickly go to mcu config and change back to "1". Then nothing works, as if it doesn't get power anymore. I unplugged it and tried to hook up a miniHDMI cable but there's no connector on this board....not sure i can even get to recovery, but i'll try again tomorrow.
I have an older v3.06 LM MCU but no working config, so i hope to get into recovery somehow and flash both.
I suppose any LM MCU version would do, along with a CFG file, as long as it's version 1 (recognizable from _1 after mcu version or check in factory settings-other-customer version "1")
does anyone have an idea where to change customer version in a dmcu.cfg using hex editor?
or is it possible to connect and edit the MCU values stored on the unit itself?
it's a PX5 MTCE LM unit, ultraslim format.
https://www.aliexpress.com/item/Eun...-Stereo-GPS-for-VW-Passat-B6/32866279122.html
Hi,
My problem is with 65P815. Fabric software was v084, i tried to update to V191 official version from TCL page, but after update and turning off TV, there is nothing shows on screen. I hear only sounds, and remote clicks, menu gone etc.
I search for info, and go back to v083 software, that helped and fixed TV. But now I don't know what to do to fix my TV. Tried to update with factory reset, nothing helped. Any tips how to deal with it ?
Next thing is concerned with soundbar thing, I have LG soundbar, is it possible to control soundbar over TCL's remote ? On my old Samsung TV it worked normally.
Here in TCL I don't see option to choose sound sourec (tv speaker/optical/hdmi), there is no option to mute TV speaker and move sound to soundbar. For now I use 2 remotes, but I want to use only one like in Samsung. I connected soundbar with optical cable to my TV.
Hi there. Trapped into same thing. After flash, I can hear 'bing' when you navigating in menu, backlight is working, but screen still black. Tried to flash V191(Inserted stick to USB2.0 with Update.img and plugged in with power button pressed). But got same thing. Led is blinking during i suppose flashing, but after that - nothing. Can it be somehow reset to stock or whatever?
you have to go back to 0.83
Turn off the TV, plug out the cable. put the drive into usb 2.0, press power button on TV's back and plug in power cord, if led start blinking wait about 10 mins to finish flashing. Sometimes you have to do this twice and TV will be ok.
Write to TCL support about your problem, let them prepare patch
Hmm... I have couple of questions then.
Does that mean v083 firmware didn't published somewhere?
And does that mean that we can't update 65p815 to any new firmware with Android 11?
what was your native FW ?
I tried to update to V191 which is on android 9, and update was failure. There is something wrong with the FW
File upload and sharing. Large file transfers. Free online cloud storage.
Visit this link to download: V8-R51MT02-LF1V083.zip
files.fm
here you can find v0.83
Android 11 is in beta now, we have to wait for official final update
I didn't check my original fware version. I know that was very stupid, but i supposed that just platform is matter.
Thanks for link. Will try this fware. Hope that will help, because i don't like to waste time with support, that usually just redirects to another operator...
it should, try second time if the first will failure
Ok, i just finish downloading and i'll start bring that baby to life. Thanks for help. Will report if suceed.
report it to TCL support to make technical request, and to fix that firmware
Ok. Just flashed twice. God damn, you have been right! All works like charm!
If someone will be as "lucky" as me, steps are next:
1. Load to local pc zip from above.
2. Format flash stick with FAT32 and copy it to root.
3. Insertt stick into USB 2.0 port.
4. Turn off TV power physycally.
5. Press and hold On/Off button on a TV's back and plug TV holding button pressed.
6. Hold for 10 secs, the led in front of TV will start blinking - it is ok.
7. Wait till it will stop blinking and wait some 5 mins after that.
8. Repeat steps 4-7. After TV restart it will show TCL logo and Android welcome screen will appear.
Ok now we should think about how to flash properly new version of FW,
latest official firmware is
https://www.mediacenter.tcl.eu/uploads/common/R51M_Android_P_V191.zip
When I try to flash with it, from menu update/local it works but only first time. When I turn off TV, then screen is black
I found such instruction, what to do after installation
Press the Settings button in the remote control:
Press OK on the icon: Picture.
Then go to the line Advanced settings.
Scroll down to the line: Brightness settings.
Scroll down to the line: Contrast.
With the remote control, do the key sequence: 6 4 2 5
The special menu appears.
Go to the line “Reset All” and press OK.
Go to the line “Reset Shop” and press OK.
Now unplug the main power cord.
Wait for ~2 minutes.
Plug back the main power cord and perform complete installation.
Click to expand...
Click to collapse
but haven't tested it yet.
Guys, can you post "Project ID" of your P815?
As ,for firmware V191 supose to be as attached....
50P815.....285
55P815.....284
65P815.....283,305
TV panel type can be found in service menu.....Main menu (1950)...
Just grabbed my panel name.
stasiof said:
Guys, can you post "Project ID" of your P815?
As ,for firmware V191 supose to be as attached....
50P815.....285
55P815.....284
65P815.....283,305
TV panel type can be found in service menu.....Main menu (1950)...
Click to expand...
Click to collapse
Seems on mine 65P815 by your table, the code should be ST6451D02-3 (code 305), but i have ST6451D02-H (code 283).
I have flashed v272 (img file) from v084 to my 65P815. Flashing went smoothly with no black screen ecountered. v272 works nicely with no problem.
TCL Android TV model 55p8m / Android Recovery TCL/BeyondTV/BeyondTV
My TCL Android TV model 55p8m has stuck and can't press any key in remote. The screen gives options to - Try Again - Factory data reset, but do not know how to select one of this option and continue without a keyboard or remote connected to the...
forum.xda-developers.com
@ancifil said:- "Did you reboot your TV after that?"
Sure I had rebooted it after flashing as I have been using this firmware for about a month.
I remembered flashing it 2 times. The first time was not successful (can't remember due to what). The second time reflash (same as what you did as in post #10) was smooth and without any problem.
jngiag, looks like it should, as for me... Maybe, i shall try 272 one more time.
superfly86, did you try 272?
jngiag said:
I remembered flashing it 2 times. The first time was not successful (can't remember due to what). The second time reflash (same as what you did as in post #10) was smooth and without any problem.
Click to expand...
Click to collapse
Btw, one thing. Can you remember, after you had flashed 272 first time and after that launched flash menu, to flash second time, was you able to see menu?
ancifil said:
Btw, one thing. Can you remember, after you had flashed 272 first time and after that launched flash menu, to flash second time, was you able to see menu?
Click to expand...
Click to collapse
I think it was due to a request to input pin while I was trying to setup live TV. I did not know the pin so I powered it off and reflashed as in post #10. Sorry, I can't remember it exactly.
ancifil said:
Seems on mine 65P815 by your table, the code should be ST6451D02-3 (code 283), but i have ST6451D02-H (code 305).
Click to expand...
Click to collapse
Your 65P815 with panel ST6451D02-H...... Project ID MUST be 283.
This is your problem with firmware (black screen ) !
So you need to change ID number from 305 to 283.
To modify the project ID, when TV is ‘ON’, with the remote control do the key sequence
0 6 2 5 9 8 .....MENU.... 283.
At the end of the key sequence the TV must reboots alone if the project ID has been understood by the TV. If it doesn’t, update the product with the last software available and try again.
Sometimes several tries can be necessary for successful project ID modification.
stasiof said:
Your 65P815 with panel ST6451D02-H...... Project ID MUST be 283.
This is your problem with firmware (black screen ) !
Click to expand...
Click to collapse
I've got that. But the hard thing is that i will not see this manipulation... I have to do that blindly. Risky stuff, right?