Hello
Posted this over in Pauls MoDaCo forum as well but not had any replies yet so thought it best to try here as well.
I've bricked my Desire, phone loads up but the sim and sd card aren't recognised (though I can still use wi fi).
When connecting the phone to my PC (tried windows 7 and XP) the drivers fail to install and I get various faults like the device being recognised as android 1.0 usb to a Qualcomm device.
The phone is still rooted (I can install rooted apps from the market) however after following various unbricking guides I always get stuck at stage 2 (i.e. enable sd card), if the PC won't recognise the device how can i run the 'fastboot oem enableqxdm 0' command?
I've also tried running fastboot using a terminal app on the phone but it doesn't recognise fastboot, should i be in a specific directory on the phone when running this command?
Any help greatly appreciated.
Cheers
Have you tried using a different jab port? I had to use one at the back of my pc front ports wouldn't install drivers properly.
Sent from my HTC Desire using XDA App
You need to follow the guide on modaco for unbricking your device. You have the usb brick, and it can easilly be fixed.
Follow the steps religiously and you will be up n running in no time again.
I've followed the guide lots of time, it's not that long winded so it shouldn't be to hard to follow.
I get stuck on step two, using the fastboot command.
My PC and also tried laptop (Win XP and 7), different USB ports (front and back) but each time it attempts to load drivers and I end up with it either being recognised as an Android 1.0, Android Bootloader Interface or a Qualcomm device. I then run fastboot, and get the device not recognised error.
I've now tried to connect my phone to a windows Xp and 7 PC and a laptop, a Linux laptop and tried using the Tiny Linux root guide to see if that would work, but each time the PC/laptop fails to recognise the phone so can't get into recovery or run the fastboot command.
celticone said:
I've now tried to connect my phone to a windows Xp and 7 PC and a laptop, a Linux laptop and tried using the Tiny Linux root guide to see if that would work, but each time the PC/laptop fails to recognise the phone so can't get into recovery or run the fastboot command.
Click to expand...
Click to collapse
You don't need to get into recovery for this.
You have sdk installed, so boot your phone by pressing power while holding down the volume down button.
Use a command prompt on your pc and cd to the tools directory in the sdk. If the sdk is saved to the root of your C: drive on the pc you would type
Code:
cd C:\android-sdk-windows\tools
When in there type
Code:
fastboot oem enableqxdm 0
This will re-enable your sd card and allow you to continue.
That doesnt work, just stops on the waiting for device line and doesnt continue.
Also using the cmd 'adb devices' shows nothing so I'm guessing my phone isn't recognised on my PC. At the moment it's in fastboot usb (on phone) and in devices on the PC I've got Android Bootloader Interface with the yellow problem sign against it.
thanks for your help, it's appreciated, tried a few forums but no one is that interested in helping.
Cheers
celticone said:
That doesnt work, just stops on the waiting for device line and doesnt continue.
Also using the cmd 'adb devices' shows nothing so I'm guessing my phone isn't recognised on my PC. At the moment it's in fastboot usb (on phone) and in devices on the PC I've got Android Bootloader Interface with the yellow problem sign against it.
thanks for your help, it's appreciated, tried a few forums but no one is that interested in helping.
Cheers
Click to expand...
Click to collapse
It definitely sounds like the old usb brick problem, so that's a good thing! When you tried the commands were you booted into fastboot? When you connect the phone to the computer does the phone display change from saying fastboot to fastboot usb? I think thats what it should say, can't remember to be honest!
Have you tried another usb port, and a different cable too?
Edit: I'd also try rebooting the computer to ensure any running process etc are closed.
Got it fixed, final throw of the dice this morning I connected the phone to a Vista laptop and it was recognised straight away, so downloaded HTCSync then ADB tools on to the laptop and finally got the re enable command to work.
Jeez that took for ever, strange that Xp, Win7 and Linux PCs couldn't recognise the phone but Vista did.
Still got it sorted, thanks for the help.
No worries. Glad you got it sorted.
I have almost the same problem.
but with the legend.
SD is not recognized.
Can´t Call,
Can´t connect via USB.
Is there something I can do in the built in terminal in the ROM?
When I connect my HTC Desire through USB cable to my laptop, my laptop wait a while then pop a windows which says USB Device Not Recognised. My device just got the orange light lit up but there is no response other than that i.e. no menu pops up to choose "charge only, disk drive" whatsoever.
It worked just two days ago before I reflash a new ROM (RCMixHD 3.6.1).
During the flash, the SD card was not recognised too so I tried to get it work by using "fastboot oem enableqxdm 0" as instructed by one post named "USB brick/rickrolled/b0rked -> FIXED!" on MoDaCo.
But I did not flash the update.zip as required cos my problem was fixed before this step.
Can anyone help me fix this problem? Waiting online
USB debugging still enabled?
What result from either adb or fastboot?
Code:
fastboot devices
adb devices
FASTBOOT shows "FASTBOOT USB", Bootloader also gives me "HBOOT USB PLUG", I think the USB cable is fine.
stringer7 said:
USB debugging still enabled?
What result from either adb or fastboot?
Code:
fastboot devices
adb devices
Click to expand...
Click to collapse
I tried the two commands in cmd, I copy down what it gives me
E:\SDK\Tools> adb devices
List of devices attached
E:\SDK\Tools> fastboot devices
HT05HPL12963 fastboot
E:\SDK\Tools>
Ok so the fastboot result means you can connect to PC.
What happens if you connect your device whilst it's booted up with USB debugging enabled? Enable this prior to connecting in settings>applications>development.
Hi thanks for the help, I managed to unbrick the USB brick. But now even though I'm able to connect to my laptop, the adb devices still doesn't give me any device. In device manager, I got an "ADB" with yellow exclamation mark under “Other Devices”, just cannot get the right driver for it. Could it be due to the USB brick?
Hey gals and guys,
my girlfriend dropped her Xiaomi A2 lite and no the touchscreen doesn't respond. The phone has the stock Android One and I can only access fastboot.
Code:
fastboot devices
recognizes the phone.
The recovery is the stock recovery.
Code:
adb devices
won't recognize the phone and gives me an empty line as output
I also can't access the phone via usb with my filebrowser. If I try, the phone makes a "bing"-sound and the filebrowser gives me:
Code:
unable to open MTP device
I am using archlinux and I also have a windows device available.
Is there any chance on getting pictures etc from the phone?
Any suggestions besides getting a replacement for the touchscreen?
Thank you so much.
Connecting via USB probably needs you to click something.
I'm guessing developer mode is not enabled...
If you've got a micro USB OTG cable, you could plug a mouse in.
If you boot TWRP (fastboot boot twrp-3.3.1-dees-troy.img) you should be able to get adb and usb transfers working. Don't need to install it, just boot it. Not sure if that works without unlocked bootloader.
If you've got a micro USB OTG cable, you could plug a mouse in.
Click to expand...
Click to collapse
This did the trick.
Thank you
So I'm trying to use fastboot but whenever i connect my phone to pc on fastboot, my pc never detects it and neither does adb. it doesn't even show in device manager. if i turn on show hidden devices it show on there but it says its not connected. and every timei connect it or disconnect it from my pc, my pc makes the sound that its connected/disconnected but it still doesn't show up in device manager and trying to install the drivers for fast boot just gives me the error "The folder you specified doesn't contain a compatible driver for your device. If the folder contains a driver, make sure it is designed to work with windows for x64-based systems." Whats weird that odin still finds the phone when its on fastboot mode. Can someone please help me?
you know what to do when device recognize on pc on usb but don't go anywhere?. My device recognize on pc but when i will run the blank flash to open the fastboot it don't run the fastboot screen and continues black. The process that i trying to do is connect the phone on pc and turn it on by the connectors on the motherboard, after that theoretically i have to put it in fastboot with blankflash and install the rom by the qualcom driver but it stops on the blankflash part. It's like my phone don't have the fastboot anymore.