Ambient light sensor location? - Nokia 8.1 Questions & Answers

Where's the ambient light sensor on this device?

Related

[Q] Ambient light sensor - does Cyanogenmod change it

Does Cyanogenmod modify how the ambient light sensor works? My E4GT sucks at adjusting because it does it to often to drastically and to quickly. I have a touchpad that when running webos it controls ambient light sensor very different than the cyanogenmod does.
If that is not part of the rom is there a way to modify/improve how the sensor works?
PS i know there is an alpha.
Should I take that as a no?
If its a no is there something I can do to improve the way the sensor responds?
My main reason is when holding the phone horizontally and my hand goes slightly over the sensor it darkens so quickly, its just annoying.

What kind of sensor it is!?

Can any body tell me which mobile display & what kind of sensor it is?coz receantly i replace my screen.
Here is the pic-
It's the proximity and ambient light sensor.

(Q) How to Check if Ambient Light Sensor is working?

Hi Guys I just wanted to know if Ambient Light Sensor is working or Not, As I have enabled Developer Options and in that when I press Manufacturer Tab then I see the Hardware Testing.
When I press Ambient Light Sensor it shows 0.0 , is it same for everyone or just me?
Also How can I test that Ambient Light Sensor is working or not?
Thanks and Regards
abbychauhan said:
Hi Guys I just wanted to know if Ambient Light Sensor is working or Not, As I have enabled Developer Options and in that when I press Manufacturer Tab then I see the Hardware Testing.
When I press Ambient Light Sensor it shows 0.0 , is it same for everyone or just me?
Also How can I test that Ambient Light Sensor is working or not?
Thanks and Regards
Click to expand...
Click to collapse
It's highly directional. If you're in a dim room, it will sit at zero until you aim it at a light. It's not very sensitive in low light, but past some threshold it will jump up. If you can't get it to change when you shine a light on it, I think you've got a problem.
Working for me in my office ...depending on whether I cover the light/lamp or not the ambient light sensor reading is changing...even when I just tilt the watch a bit....I am on 5.0.2...never checked before...

S9 / S9+ Ambient Light sensor disabled in stock... Ish rom

The notification led is connected to the ambient light sensor so in a dark room the led is dim, in a light room the led is bright.
However if you're out and about in even a slightly bright day and take your phone out of your pocket (which is dark) you can barely see the led because it's been in your dark pocket.
This isn't a hardware limitation, if you install Resurrection Remix or Liniage OS the led is bright all the time.
I'm running a stock based custom os because of the camera quality.
I just wondered if anybody has worked out a way to either disconnect the led from the ambient light sensor or even disable the light sensor all together... I don't use it.
I've tried the Xposed Sensor disabled but it didn't work on either BRF5 or ARC5
batfink1 said:
The notification led is connected to the ambient light sensor so in a dark room the led is dim, in a light room the led is bright.
However if you're out and about in even a slightly bright day and take your phone out of your pocket (which is dark) you can barely see the led because it's been in your dark pocket.
This isn't a hardware limitation, if you install Resurrection Remix or Liniage OS the led is bright all the time.
I'm running a stock based custom os because of the camera quality.
I just wondered if anybody has worked out a way to either disconnect the led from the ambient light sensor or even disable the light sensor all together... I don't use it.
I've tried the Xposed Sensor disabled but it didn't work on either BRF5 or ARC5
Click to expand...
Click to collapse
Turn off Automatic screen brightness? Is the LED not connected to the screens brightness level?
Ummm, actually when I said I don't use the light sensor, I figured it was obvious that I don't use automatic screen brightness (since it uses the ambient light sensor).
Anyway, no.. The led isn't connected to the screen, it's connected to the same sensor as the screen... The ambient light sensor.
You can tell the screen to ignore the ambient light sensor by turning off automatic screen brightness, that however doesn't turn off the sensor.. So the notification led is still controlled by the light sensor.
Have you tried any of the notification apps on Play or Samsung Appstore? There's quite a few free ones available on Play but I've never had the need to try any on this phone.
I've tried them all, I like lightflow the best.
They let you control the brightness up to 100%, but that's 100% of the brightness controlled by the ambient light sensor which in turn answers to the Samsung software.
*Sigh*, if I can't find an answer, I might take my balls in my hand and open one of the phones and physically disconnect the sensor.. It's only a cable with a plug.
I also have an S8+ and it does the same thing.
batfink1 said:
I've tried them all, I like lightflow the best.
They let you control the brightness up to 100%, but that's 100% of the brightness controlled by the ambient light sensor which in turn answers to the Samsung software.
*Sigh*, if I can't find an answer, I might take my balls in my hand and open one of the phones and physically disconnect the sensor.. It's only a cable with a plug.
I also have an S8+ and it does the same thing.
Click to expand...
Click to collapse
LOL, if you do let us know how it comes out.....the sensor not the balls.
Has anyone solved the troublesome problem?

How to turn-off proximity sensor?

I don't use pocket mode and AOD, But the proximity sensor blink endlessly.
I know this is invisible light, It can cause cataracts.
Your browser is not able to display this video.
Light and Infrared Radiation
ehs.lbl.gov

Categories

Resources