Dead after Qi charging?! - Nexus 7 (2013) Q&A

Hi Guys,
I'm hoping someone can point me in the right direction here, firstly, I have indeed used the search function and I am more than aware of the many cases of dead tablets with charging issues. As such, I have also tried all of the proposed solutions with no joy so far....
So my N7 2013 is basically my old work tablet that was never used, literally sat in my drawer for 3 years not even out of the box but a couple of years ago I started to use it, loaded it up with a custom ROM and everything was well, no issues whatsoever as it was a brand new tablet. Now, my PC monitor has a QI charger in the base and I had been charging the tablet on there for months but one day it was left on there all day and when I got back later on that day, it was dead..... It was warm to the touch, normal for charging but would not power on. No indicator light or anything.
When plugging in the usb cable to charge, I get nothing, no indicator or anything.
I have held the power button for well over a minute and nothing.
I have held the power and volume down button for well over a minute and nothing.
I have done both of the above with power plugged in and not plugged in, nothing.
I have replaced the battery with a brand new one, nothing.
I have checked the contacts for the QI charging meet the tabs as I read this and the USB charging is on the same circuit, nothing.
I have vaguely read something about quite literally "jump starting" dead N7's and I have not yet gone down this road, I'm hoping there is something obvious I have missed.
Can anyone suggest anything else?
Thanks in advance! :good:

sirleeofroy said:
...I have replaced the battery with a brand new one, nothing..:
Click to expand...
Click to collapse
Hi, the new battery may be faulty too. Measure its voltage - if it is below 3V, it is faulty for sure.
If it is above 3.0V but below 4.0V, recharge it externally in any Lipo charger to 4.2V, then re-connect it to N7 and try to power up.
Your N7 may work on pre-charged battery, but be unable to recharge it because of an internal fault. There is no N7 schematic available and component-level repair is unlikely, but if it works on pre-charged battery then you could do "no battery mod" and keep this great tablet alive and useful. So, do the above tests and search for the mod, which is very popular for car use.
:highfive:

k23m said:
Hi, the new battery may be faulty too. Measure its voltage - if it is below 3V, it is faulty for sure.
If it is above 3.0V but below 4.0V, recharge it externally in any Lipo charger to 4.2V, then re-connect it to N7 and try to power up.
Your N7 may work on pre-charged battery, but be unable to recharge it because of an internal fault. There is no N7 schematic available and component-level repair is unlikely, but if it works on pre-charged battery then you could do "no battery mod" and keep this great tablet alive and useful. So, do the above tests and search for the mod, which is very popular for car use.
:highfive:
Click to expand...
Click to collapse
Thanks for the reply, I hadn't thought to check the new battery.... I'll do that tonight..... The "no battery" mod is no good to me unfortunately as I want the tablet as a tablet..... I already have an android head unit in my car...
The thing I find slightly jarring is that if i put the tablet on my wireless charger, it gets really warm at the top end of the tablet but with the USB, literally nothing. The charging indicator has not been seen since it first wouldn't turn on.

sirleeofroy said:
Thanks for the reply, I hadn't thought to check the new battery.... I'll do that tonight..... The "no battery" mod is no good to me unfortunately as I want the tablet as a tablet..... I already have an android head unit in my car...
The thing I find slightly jarring is that if i put the tablet on my wireless charger, it gets really warm at the top end of the tablet but with the USB, literally nothing. The charging indicator has not been seen since it first wouldn't turn on.
Click to expand...
Click to collapse
Ok, so I've tested both the old and new battery and both are at a solid 3.8v as per the battery spec

Related

[Q] A100 Powers OFF when charger is connected.

Recently successfully replaced the LCD screen on my Acer A100. Device worked fine for some time after that repair. Wanting to get a secondary charger for use at work I went to radio shack. Sales "tech" tried several different adapters, found one that fit inside he port, but wiggled. She plugged it in but device wasn't showing a charge. Decided to order one from online. At home the device still would not charge with its own charger. Thought maybe the charger was faulty. Ordered two more. Still the A100 turned off when charger plugged in. Figured tech had burned out the a/c port. Ordered and installed a new one. Still A100 turns off immediately when charger is plugged in. I have 3 chargers now - same results with all 3. Have now ordered a docking station to utilize (hopefully) charging ability through 40 pin connector.
If this connection creates same shut down am I looking at a battery replacement? AM sitting at 33% battery level now, device shut down completely.
Acer wants 199.00 prepaid to submit to them for repair - this is more than I paid for the device! Not really an expense I am willing to pay if all it needs is a battery. There is no erratic behavior , just immediate shutdown as soon as a charger is connected. Any ideas?
PocketFuzz said:
Recently successfully replaced the LCD screen on my Acer A100. Device worked fine for some time after that repair. Wanting to get a secondary charger for use at work I went to radio shack. Sales "tech" tried several different adapters, found one that fit inside he port, but wiggled. She plugged it in but device wasn't showing a charge. Decided to order one from online. At home the device still would not charge with its own charger. Thought maybe the charger was faulty. Ordered two more. Still the A100 turned off when charger plugged in. Figured tech had burned out the a/c port. Ordered and installed a new one. Still A100 turns off immediately when charger is plugged in. I have 3 chargers now - same results with all 3. Have now ordered a docking station to utilize (hopefully) charging ability through 40 pin connector.
If this connection creates same shut down am I looking at a battery replacement? AM sitting at 33% battery level now, device shut down completely.
Acer wants 199.00 prepaid to submit to them for repair - this is more than I paid for the device! Not really an expense I am willing to pay if all it needs is a battery. There is no erratic behavior , just immediate shutdown as soon as a charger is connected. Any ideas?
Click to expand...
Click to collapse
If its doing it on 3 chargers its sounding more like a board charging circuit issue. You could remove the battery and then see if it behaves normally, that'll be battery or board right there. Or if you have a multi meter test output at the battery connector.
Tapatalked from my HTC DNA - ReVolt
Tried connection without battery
pio_masaki said:
If its doing it on 3 chargers its sounding more like a board charging circuit issue. You could remove the battery and then see if it behaves normally, that'll be battery or board right there. Or if you have a multi meter test output at the battery connector.
Tapatalked from my HTC DNA - ReVolt
Click to expand...
Click to collapse
Don't have a multi meter. Tried connection via new docking station, got same response: device immediately shut off. Tried your suggestion, disconnected battery connected to docking station, got immediate shut off. Same with charger via a/c port. :crying: Mainboard is out? But Device responds and acts normal when in battery mode - or is this isolated to the charging circuit part of the main board?
Thanks for the suggestion!
PocketFuzz said:
Don't have a multi meter. Tried connection via new docking station, got same response: device immediately shut off. Tried your suggestion, disconnected battery connected to docking station, got immediate shut off. Same with charger via a/c port. :crying: Mainboard is out? But Device responds and acts normal when in battery mode - or is this isolated to the charging circuit part of the main board?
Thanks for the suggestion!
Click to expand...
Click to collapse
Sounds like its tripping on the charger circuit and cutting out, like a breaker tripping. IMO look carefully for any shorts on the boards, even something stupid like dog hair can cause strange things to happen. A good blasting with air wouldn't hurt either. It could even be the dock port as it does charge from there and is subject to debris also.
Tapatalked from my HTC DNA - ReVolt
one more try
pio_masaki said:
Sounds like its tripping on the charger circuit and cutting out, like a breaker tripping. IMO look carefully for any shorts on the boards, even something stupid like dog hair can cause strange things to happen. A good blasting with air wouldn't hurt either. It could even be the dock port as it does charge from there and is subject to debris also.
Tapatalked from my HTC DNA - ReVolt
Click to expand...
Click to collapse
Thanks again for more suggestions. Yup I have been over the board and all connections with a looking glass. Changed out the A/C dock port. My suspicion is that when the Radio Shack tech powered up the "Almost fits" adapter it blew whatever breaker the board has.
When I had it connected to the docking station with the battery disconnected, it powered on, then immediately shut off. So this definitely sounds like a "blown fuse". I completely disassembled and reassembled it again (except for the LCD screen) and checked all connections and plugs. Nothing visible to indicate a burnout or cross connection.
No odd smells either. Probably some teensy weensy transistor or resistor or something. I am not an electrician - just good at R & R.
Another visit to ebay and I am parting with 50 bucks for a "factory refurbished" motherboard. In the mean time, my beloved tablet will await further surgery. Will keep you posted. Board should be here by Saturday. I hope so - battery is down to 27%. Thanks again for weighing in!
PocketFuzz said:
Thanks again for more suggestions. Yup I have been over the board and all connections with a looking glass. Changed out the A/C dock port. My suspicion is that when the Radio Shack tech powered up the "Almost fits" adapter it blew whatever breaker the board has.
When I had it connected to the docking station with the battery disconnected, it powered on, then immediately shut off. So this definitely sounds like a "blown fuse". I completely disassembled and reassembled it again (except for the LCD screen) and checked all connections and plugs. Nothing visible to indicate a burnout or cross connection.
No odd smells either. Probably some teensy weensy transistor or resistor or something. I am not an electrician - just good at R & R.
Another visit to ebay and I am parting with 50 bucks for a "factory refurbished" motherboard. In the mean time, my beloved tablet will await further surgery. Will keep you posted. Board should be here by Saturday. I hope so - battery is down to 27%. Thanks again for weighing in!
Click to expand...
Click to collapse
To bad considering the crappy battery life so its not like you can charge some other way and swap the battery around.
Example, I have a bricked unit that charges but doesn't otherwise work, so I mean using my bricked board to charge it and the non charge board for use. The a100 isn't really a good setup for swapping around lol. I may actually be interested in that board now that I think about it...
Tapatalked from my HTC DNA - ReVolt
hmmm an idea for the brave
pio_masaki said:
To bad considering the crappy battery life so its not like you can charge some other way and swap the battery around.
Example, I have a bricked unit that charges but doesn't otherwise work, so I mean using my bricked board to charge it and the non charge board for use. The a100 isn't really a good setup for swapping around lol. I may actually be interested in that board now that I think about it...
Tapatalked from my HTC DNA - ReVolt
Click to expand...
Click to collapse
If I could figure out a way to charge the battery OTHER than through the board - I would! Which got me to thinking. One COULD get a second rear panel, cut a door in it, install teensy weensy hinges or create a hinge with cloth tape. then make some sort of extension cord for the battery charging cord, plug it in to the "external" charging board and refill the battery that way.
With a working board and the right know how, one could just extract the board, put it in a box and make a charger out of it too.
But that is just my brain rattling around ideas. :silly: Hopefully this new "refurbished" mother board will do the trick and I will learn my lesson and NEVER let a sales "tech" attempt trial adapters! at 10 minutes to 9pm tonight it was in Texas....
Until I CANNOT use it, I didn't realize how MUCH I used this little tablet!
now it blinks orange?
Oh fer cryin out loud! The motherboard has arrived, I have installed it. Can plug n the charger and drop it onto the docking station and now I get the same response for both charging options: Charge LED lights up orange solid for just about 60 seconds, then begins blinking. Device doesn't respond when power button is pushed UNLESS it is plugged in, and then it just sits at the "ACER" screen.led changes to blue.
OK, wait a minute, this is the third time I have turned it on while plugged in. Acer screen has moved to Android, Device has started. Battery icon showing a question mark. 23%
Turned off, turned back on, now battery shows only 3%????
Think I saw something on the forums about that. will go on a quest.
Finally charging again!
Shhh, don't want to disturb my device....
Found folks on other forums with similar issues of the Acer A100 tablet showing only 3% charge. I removed and inserted the charging pin several times, the device would show solid orange led for about one minute then start blinking. Turned the device on when charger plugged in, unlocked the screen, then with device still plugged in I shut it down completely. Removed charger. Plugged it back in and so far the led is staying at solid orange.
Please keep your fingers crossed for me! This has been quite the roller coaster ride of discovery. Will leave it be for overnight (what is left of the overnight). Then peek at it in the morning. With any luck at all it will have accepted a full charge and I will be greeted with a functioning device! I almost want to learn a new trade..
well now that is weird, got up this morning to a nice blue charge indicator. Yay! Unplugged charger, press on button, hold, hold, hold, hold, hold and device does not start up. Dang it! Plugged it back in, led went solid orange, then started blinking again! Pressed and held on button. Device came on. battery meter shows 3% and a question mark! HUH?
have device plugged in, settings of course show android version 3.2.1 for this motherboard. Guess I need to upgrade it to ICS maybe that will resolve this weird battery issue? Hope soemone here has ideas, feels like I am soooo close to resolving this.
I read the upper posts.
Now I want to share my experience regarding battery load sharing:
I have allso problems to charge the battery.
I have on my tab, for example, 40% of battery power.
I turn my tab off.
When i plugged the charging cable in it shows me the orange led for load.
After two hours or more i turned the tab on.
It shows me not more than 40% but only 37% or so.
So not loaded. This was a bad sign....
I dont no was happend.
I get a little bit nervous but when the tab not get power it doesnt work....
After two/three hours the battery was empty.
Now i can only start my tab while plugged the charging cabel in because the battery will not load.
I have tried several options to find a solution (disconnect the battery, install a new battery, etc. ....).
My solution was fairly straightforward:
I open the tab. Look where the power comes in.
Of the charging socket go four (two red and two black) cable to the motherboard and from the motherboard it goes seven (two red, two black and for me not so important three other coloured cabels) to the battery.
I organized four thin wire and soldered it from the charging socket directly to the battery (of course red to red black to black ).
The result:
When i plugged the charging cabel in while android is running i get no information to load and it shows me not to.
But when i turned the tab off and on again it shows me that it has the battery charged :fingers-crossed: .
After on night while the charger plugged in the battery is fully loaded!!
And of course i get the information in android the discharging of the battery but this is an normaly thing!
So, the problem to load the battery for me is solved .
I hope it helps a little bit for everyone!
frischeis said:
I read the upper posts.
Now I want to share my experience regarding battery load sharing:
I have allso problems to charge the battery.
I have on my tab, for example, 40% of battery power.
I turn my tab off.
When i plugged the charging cable in it shows me the orange led for load.
After two hours or more i turned the tab on.
It shows me not more than 40% but only 37% or so.
So not loaded. This was a bad sign....
I dont no was happend.
I get a little bit nervous but when the tab not get power it doesnt work....
After two/three hours the battery was empty.
Now i can only start my tab while plugged the charging cabel in because the battery will not load.
I have tried several options to find a solution (disconnect the battery, install a new battery, etc. ....).
My solution was fairly straightforward:
I open the tab. Look where the power comes in.
Of the charging socket go four (two red and two black) cable to the motherboard and from the motherboard it goes seven (two red, two black and for me not so important three other coloured cabels) to the battery.
I organized four thin wire and soldered it from the charging socket directly to the battery (of course red to red black to black ).
The result:
When i plugged the charging cabel in while android is running i get no information to load and it shows me not to.
But when i turned the tab off and on again it shows me that it has the battery charged :fingers-crossed: .
After on night while the charger plugged in the battery is fully loaded!!
And of course i get the information in android the discharging of the battery but this is an normaly thing!
So, the problem to load the battery for me is solved .
I hope it helps a little bit for everyone!
Click to expand...
Click to collapse
I really hope other isn't any voltage or amperage changes needed of that can blow that battery up real quick, plus it can't stop charging, you'll need to monitor that yourself.
Thanks for the info though, it does appear to be yet another somewhat common bug these have that can be addressed by a user if they feel the need to.
Tapatalked from my HTC DNA - ReVolt
Not switch the charger off when the battery is full?
I think the charger there is a shutdown would otherwise overload the battery, right?
Or do this the motherboard?
Anyway, for me the tab is fully working now and if the battery is broken, it is not a big expense to replace them .
frischeis said:
Not switch the charger off when the battery is full?
I think the charger there is a shutdown would otherwise overload the battery, right?
Or do this the motherboard?
Anyway, for me the tab is fully working now and if the battery is broken, it is not a big expense to replace them .
Click to expand...
Click to collapse
I was saying the board is in charge of cutting the battery charge off, not the charger itself so maybe keep an eye on it, its a good way for an explosion or fire.
Tapatalked from my HTC DNA - ReVolt
A100 tablet not charging still
Frischies is much braver than I am.
Wiring the battery direct to the charging port- I would definitely worry about burning up the battery or causing a fire - especially while charging when I sleep. I have had more than my fair share of run ins with fire.
The Motherboard I ordered arrived and I installed it. It was listed as "factory refurbished", but unfortunately will not accept a charge. I thought it had charged overnight at one point, but all it does is blink orange and the battery reads 3% or 0%. Turning the device off when plugged in and doing a reset has not helped. The vendor has been gracious to do a replacement, so I will follow that route until I get a working motherboard.
I have discovered that the docking station will be a welcome addition to my Acer tablet paraphernalia! Although this model docking station isn't the one that allows HDMI throughput, it still will be nice for music, and other media. A Bluetooth keyboard and the tablet will offer yet another computer tool!
First things first though, get the tablet to accept a charge - until then it is a really wide flat paper weight! I am getting VERY adept at opening the tablet and removing the internals!
It is working again! The motherboard sent was defective but vendor issued an RMA. Received the replacement yesterday, installed it last night. Charged over night and fully functional this morning! Ahhh it feels good to have my little buddy back again. Didn't realize how much I used it, until I couldn't use it! Thanks to all for the help.
Sent from my A100 using xda app-developers app

Note 8 5110 dead?

The other day I plugged in the Note 8 at night, all was fine. When I picked it up the next day, it was totally dead. There is no charging light. I have tried several chargers. I have tried holding down the power button for over a minute. I took the back off and pulled the battery and reinstalled it. Nothing. Tried multiple chargers (all of which are in working order and several that were used to charge this device previously)
Could this possibly be a bad battery? I would try replacing the battery if it seemed like a possibility, but I've never had a battery go instantly bad. It would make more sense if it just wasn't holding a charge but the charging light would still be on.
It's just out of warranty by a month. Anyone think it's worth spending the money on a new battery?
Thanks in advance for any wisdom
My 5110 does not have a removable battery, though I had two bad samsung USB charging cables, and went to Blackberry and Samsung cables. My second Samsung cable melted down and just about caused a fire at the tablet's connector.
gooberdude said:
My 5110 does not have a removable battery, though I had two bad samsung USB charging cables, and went to Blackberry and Samsung cables. My second Samsung cable melted down and just about caused a fire at the tablet's connector.
Click to expand...
Click to collapse
Thanks for your response. It's not officially removable, but it just involves removing the back and then 8 screws. I'm certain it's not a cable problem. I've tried most every cable and charger I have and they all work on other devices.
I guess I'm a little confused. Where is the charging light? There aren't any LED's on the 5110 and the charger doesn't have any either.
As mentioned, the Note 8's battery is not intended to be replacable, as other phone batteries are. It is doable, and would be my first attempt as it sounds like you've tried multiple chargers.
Beyond that, I doubt anyone here would be able to diagnose without seeing it personally.
Charging light
Eodmule said:
I guess I'm a little confused. Where is the charging light? There aren't any LED's on the 5110 and the charger doesn't have any either.
Click to expand...
Click to collapse
Ok, I have to admit it, I cannot actually remember what it looked like when powered off and charging (mainly because it is rarely powered off). Can someone tell me - Isn't there a battery symbol that displays in the middle of the screen? If so, even if the battery was totally honked, my uneducated guess is that it would still show the battery symbol perhaps with a yellow triangle.
If there is not supposed to be any charging indication at all, then my hopes are higher, because that's what I see.
Either way, I've got a battery on order, so I'll let you know what happens.
pro450 said:
Ok, I have to admit it, I cannot actually remember what it looked like when powered off and charging (mainly because it is rarely powered off). Can someone tell me - Isn't there a battery symbol that displays in the middle of the screen? If so, even if the battery was totally honked, my uneducated guess is that it would still show the battery symbol perhaps with a yellow triangle.
If there is not supposed to be any charging indication at all, then my hopes are higher, because that's what I see.
Either way, I've got a battery on order, so I'll let you know what happens.
Click to expand...
Click to collapse
The only battery indicators are on the screen. When it's powered off and charging you should see the battery in the center charging up. If the battery is hosed it'd be like no battery is in there at all, and on Samsung devices you won't see anything on the screen if no battery is present while power is plugged in.
My clients frequently have the microUSB port (charger port) go bad on tablets in general. If you've got a can of air, blow out the inside of that port (You can also use a compressed air line, but be a little more careful with that). You might also benefit by checking out the condition of the contact pins in there.
Other than that, try a different cable and a different USB charging brick. Try to use the original one that came with it, then try one that has an output of at least 1 amp (The one that came with mine was a 2 amp, but it charges alright with 1 amp). And check your outlet. It sounds stupid, but you never know.

[Q] Tablet Refuses to power on

Hello XDA members. I have a very troublesome issue with my galaxy tab 3 7.0 inch tablet. It will NOT turn on at all, no battery charging, no device power on, no comp recognition, nothing. I have already tried:
Letting it charge overnight (factory charger along with others) with several known working cables
Unplug battery for 5 minutes
Press and hold power, Vol Down, and home for 10 sec, 30 sec, and 1 minute
Press and hold power and vol down for 10,30,60 seconds.
I sent it in for repair and they wouldnt fix it because it's rooted. When I got it back it briefly turned on to the battery charging, but nothing since. I'm thinking there must have been some way they got it on.... All proper drivers are installed on PC and it's never been dropped, water damaged, etc.
Would anyone be able to provide insight as to why and provide a fix?
My 8 inch tab 3 wasn't coming on either a few days back, I got it back on by holding home and the power button for a while. I was about to give upwhen the battery charging image came on. I think I did the same again and it came on normally.
a97antonio said:
My 8 inch tab 3 wasn't coming on either a few days back, I got it back on by holding home and the power button for a while. I was about to give upwhen the battery charging image came on. I think I did the same again and it came on normally.
Click to expand...
Click to collapse
Was that from computer or wall?
From wall, it was about 3/4 charged by then
a97antonio said:
My 8 inch tab 3 wasn't coming on either a few days back, I got it back on by holding home and the power button for a while. I was about to give upwhen the battery charging image came on. I think I did the same again and it came on normally.
Click to expand...
Click to collapse
a97antonio said:
From wall, it was about 3/4 charged by then
Click to expand...
Click to collapse
Still no luck... I can feel the tablet getting hot down at the charge port so I know it's charging, and i know the lcd isn't damaged.
Mine is in the same condition. Anyone know how or why this happens and how to fix it?
Sent from my LG-LS980 using Tapatalk
Not sure if this will help, but just like with phones, sometimes android tablets just need a battery pull. My kids xo tablet went dead and before I tossed it in the trash I took the housing off and had to clip the + wire since it was soldered to the board. Twisted it back together to check and sure enough the tablet powered on like normal. Ive had to pull the battery on an Sm-t217a and it was a lot easier. They have a removable clip that attaches to the board.
Sent from my SAMSUNG-SM-T217A using XDA Premium 4 mobile app
I think it might be the battery itself. Just for giggles I left it plugged in for days and i just checked back on it and the Battery charging screen kept flashing on and off. Won't hold any charge. Probably will just order a new battery and see what happens. I pulled the battery a couple times and nothing happened. Closer inspection found that the tech that looked at it damaged the battery cord (unless it came with the copper on the wiring already exposed...)
xkn0s said:
I think it might be the battery itself. Just for giggles I left it plugged in for days and i just checked back on it and the Battery charging screen kept flashing on and off. Won't hold any charge. Probably will just order a new battery and see what happens. I pulled the battery a couple times and nothing happened. Closer inspection found that the tech that looked at it damaged the battery cord (unless it came with the copper on the wiring already exposed...)
Click to expand...
Click to collapse
You might be right about the battery being dead, although they usually don't just go all at once like that. The charge indicator flashing is odd. The only thing close I've seen is an "x" over the icon when there aren't enough amps (my tab needs 2 amps. 1 amp chargers and some pc usb ports give me the x.
If you have an old cable you can cut, you could try to charge the battery itself to see if it takes a charge (or at least use a multimeter on it to check for voltage). Then you could narrow it down a bit to whether it is the battery or possibly the charge port/hardware..... I saw a bit of exposed wire just before the clip of mine too, made me extra careful pulling the clip up.
rmntruexjr said:
You might be right about the battery being dead, although they usually don't just go all at once like that. The charge indicator flashing is odd. The only thing close I've seen is an "x" over the icon when there aren't enough amps (my tab needs 2 amps. 1 amp chargers and some pc usb ports give me the x.
If you have an old cable you can cut, you could try to charge the battery itself to see if it takes a charge (or at least use a multimeter on it to check for voltage). Then you could narrow it down a bit to whether it is the battery or possibly the charge port/hardware..... I saw a bit of exposed wire just before the clip of mine too, made me extra careful pulling the clip up.
Click to expand...
Click to collapse
I wouldn't even know where to start with the wiring. Multimeter isn't something I have access to, and it seems a little complicated for me to spend time on.
When I say it's flashing, I mean the device powers on to the battery charging screen, then dies, wash rinse repeat. If I go into recovery, same thing. It all happens within a couple seconds, so it's hard to describe.
My dad has one that I can pull the battery from, I might do that. Batteries are like 20 bucks on amazon, so I think I'll test with my Dads and if it works just order a battery and report back here.
similar problem here
rmntruexjr said:
You might be right about the battery being dead, although they usually don't just go all at once like that. The charge indicator flashing is odd. The only thing close I've seen is an "x" over the icon when there aren't enough amps (my tab needs 2 amps. 1 amp chargers and some pc usb ports give me the x.
If you have an old cable you can cut, you could try to charge the battery itself to see if it takes a charge (or at least use a multimeter on it to check for voltage). Then you could narrow it down a bit to whether it is the battery or possibly the charge port/hardware..... I saw a bit of exposed wire just before the clip of mine too, made me extra careful pulling the clip up.
Click to expand...
Click to collapse
My daughters tab 3 7 inch T210 also refuses to start. First time it was fixed by opening the device and disconnecting the battery. Now that doesn't help anymore. If I attach the original charger and measure the voltage when the device has rested for some months I can see that the voltage slowly rises so it seems to do the charging even if there is no sign of charging on the screen. After some hours of charging I measure 3,78V on the battery, after disconnecting the battery.
If I attach the battery and turn on the device I measure 3,76V before I push the start button and 3,74V directly after pushing the button. After about 15s the voltage goes back to 3,76V. Nothing happens on the screen... Tried with different combinations of pushing on-button and volume up, volume down, menu....
So -the best thing would of course be a quick visit to local shop to buy a new device of another brand but for some reason I refuse to give up.
Any advice would be appreciated.
(I Have made no significant modifications but the 4-year old daughter may have contributed in an unknown way )
magnusn68 said:
My daughters tab 3 7 inch T210 also refuses to start.
So -the best thing would of course be a quick visit to local shop to buy a new device of another brand but for some reason I refuse to give up.
Any advice would be appreciated.
(I Have made no significant modifications but the 4-year old daughter may have contributed in an unknown way )
Click to expand...
Click to collapse
The better way to test if your tablet can turn on: buy a new battery, under $15 on Ebay since your old battery is dead or completely drained.
Use the new battery to turn on your tablet. If it's on, check the build number of your device after go to About My Device: if it's not end with OB1, the latest firmware which fix charging issue.
It's more likely your build number is MK1 to NI1, the build numbers count by alphabet order. Upgrade the software via Wifi, battery must be at least 25%, otherwise your tablet won't allow you to upgrade. Bring the firmware to the current OB1, your tablet should take charge normally, otherwise the USB charging port is defective or damaged. This micro USB is cheap, around $2, but it need to solder to motherboard to replace the defective one.

No Power - Tab S Dead?

So I woke up this morning to find my Tab drained. I plugged it in for half an hour, then when I picked it up I noticed there was no charging indicator (the green liquid battery thing). So I thought maybe I didn't plug it in right. I reattached everything, tested the charger on another device, then plugged it back into the tab for about 2 hours...still no juice. I tried powering on and doing the reset thing. still nothing. I brought it to a Samsung service center and they said I have a faulty motherboard. Now I'm wondering how the hell that happened when I've been using this device for about 6 months (only 6 months) without any issues, no overheating or strange reboots or anything, and now just like that I have a motherboard issue? The kicker here is that they're charging 75% of the tablet price to fix it! What gives?! I purchased it from a non-samsung mall store so they said I can't claim warranty. I popped the back off and did the battery pull thing and tried to charge - still nothing. Did I buy a device that decided it was a lemon after 6 months light-moderate use?
Anyone else have this happen? It's never been dropped or anything and I was on stock firmware with nothing but root.
In the UK, If your tablet goes faulty in 12months your guarantee is with the place you bought it from, not Samsung.
John.
It's ALIVE! I thought I'd get a 2nd opinion on my Tab since the guys at the Samsung service center popped it open anyway. Went to a generic phone repair store, all they did was hook it up to this box thing, and it came back to life! The guy said something got corrupted and just re flashed everything to stock rooted. He charged me less than $20 and I have a working Tab again. Obviously the very first thing I did with my resurrected device was to call Samsung's hotline and report how this one service center was trying to scam me into buying a motherboard that cost nearly as much as what I paid for the thing brand new.
Some li-poly battery have an protection circuit built in, if the voltage falls below a certain level say 2.5volts per cell, it disables the battery, if you connect an meter to the battery you will get 0volts , you need an li-ion charger that passes an higher voltage that resets the battery and allows it to work again, I wonder if this is what happened.
http://batteryuniversity.com/learn/article/low_voltage_cut_off
John.
Did they connect via USB or to the motherboard?
@tinderbox could be...must have over-drained itself for some reason.
@ashyx I couldn't really see what he was doing since his work table was obstructed by a bunch of stuff and he had his back towards me, I just saw him grab this small black box, then minutes later he showed me that the tab was already powering on though couldn't get past samsung logo, then he went ahead and flashed to stock.
Reason I ask is I wonder if he used a jtag box to ressurect it by reflashing the bootloader.
If he did there must be jtag points on the board as it can't usually be done via USB.
Pity you didn't ask what he actually did as I'm intrigued now.
Did the box look like this: riff box
ashyx said:
Reason I ask is I wonder if he used a jtag box to ressurect it by reflashing the bootloader.
If he did there must be jtag points on the board as it can't usually be done via USB.
Pity you didn't ask what he actually did as I'm intrigued now.
Did the box look like this: riff box
Click to expand...
Click to collapse
Yes! but without the markings.:good:
pawces said:
Yes! but without the markings.:good:
Click to expand...
Click to collapse
Exactly the same or just similar?
yeah i think so... it had similar ports, though not sure about the outer shell of it... i think it was smooth all around with no ridges or anything, just a little black rectangular box.
Sorry to revive an old topic, but i thought i'd do an update instead of start a new one. Tab S died again and I'm now convinced it's over-discharge, as I left it at about 20% and forgot to plug it in before going to bed. Woke up with the tab drained, not responding to any button combinations, not charging with any of my chargers that tested ok with other devices.
Instead of bringing it back to the technician, I thought I'd try mcguyvering the damn thing. I opened up the back, pried the battery terminals up off the board, lifted the battery out, and with a spliced USB cord hooked up to a powerbank, I gave the battery terminals a direct zap, inserting the exposed USB wires into the battery terminals. This took some trial and error as, I didn't know which wire was supposed to go where, but finally I saw the powerbank leds blink, indicating it was discharging into something. I held the wires in place for about 5-10 minutes, noticing some heat on the battery by then. I reinstalled the battery back into the tablet, closed everything up and tried charging again and...hey presto! the tab started charging. :victory: Let it charge for 2 hours and powered on like nothing happened.
disclaimer:
I don't recommend you defibrillate your device's battery unless you know exactly what you're doing and are fully aware of the risks. (I didn't know what I was doing at the time but I was so frustrated at that point I didn't mind if the battery blew up in my face.)
Mine just dead last night while CHARGING (turned off at 13%).....
And refused to turn on till now (still charging and both warm (charger + tab)...
I even plugged an ampere meter to really know if its drawing any or not (it is, at 5.2V 1.7A for 15mins)...
And still no luck
Samsung's device become more ****ty each generations..... Esp the battery...
This one is the replacement batt they gave me after 2mos of usage for infamous Tab S battery issue...
I saw a video on youtube, a guy had a dead 10.5" T1 he took the back off and connected an 1amp microusb charger pcb to connections directly to the battery under a piece a tape, I bought a couple of the microusb charger pcb`s from ebay for 0.42p each in case mine goes dead.
EDIT: I found the video.
https://www.youtube.com/watch?v=BRTgLGrzNz0
John.
pawces said:
Sorry to revive an old topic, but i thought i'd do an update instead of start a new one. Tab S died again and I'm now convinced it's over-discharge, as I left it at about 20% and forgot to plug it in before going to bed. Woke up with the tab drained, not responding to any button combinations, not charging with any of my chargers that tested ok with other devices.
Instead of bringing it back to the technician, I thought I'd try mcguyvering the damn thing. I opened up the back, pried the battery terminals up off the board, lifted the battery out, and with a spliced USB cord hooked up to a powerbank, I gave the battery terminals a direct zap, inserting the exposed USB wires into the battery terminals. This took some trial and error as, I didn't know which wire was supposed to go where, but finally I saw the powerbank leds blink, indicating it was discharging into something. I held the wires in place for about 5-10 minutes, noticing some heat on the battery by then. I reinstalled the battery back into the tablet, closed everything up and tried charging again and...hey presto! the tab started charging. :victory: Let it charge for 2 hours and powered on like nothing happened.
disclaimer:
I don't recommend you defibrillate your device's battery unless you know exactly what you're doing and are fully aware of the risks. (I didn't know what I was doing at the time but I was so frustrated at that point I didn't mind if the battery blew up in my face.)
Click to expand...
Click to collapse
Crescendo Xenomorph said:
And still no luck
Samsung's device become more ****ty each generations..... Esp the battery...
This one is the replacement batt they gave me after 2mos of usage for infamous Tab S battery issue...
Click to expand...
Click to collapse
Samsung tablets only have issue with battery connectors. The white connector with 6 wires has loose connection, the black connector soldered to mainboard has cracked solder joints. New battery won't solve problem if you don't fix these two flaws. Resolder the battery connector will fix most of problems: not charging, reboot, flickering, auto shutdown.
I posted more details in the threat: flickering screen.
so the problem is Samdung's QC....
anyway no more somedung, I switched to Xiaomi Mi Mix, still preordering from China.....
You have to watch these chinies owened tablet and phone manufactues, they have been found to come with built in spyware, sending copys of all your texts ect back to china, it`s been in the news that last few day`s
Lenovo notebooks had a spyware app and Lenovo had to issue insturctions on hot to remove it once it was found.
John.
Crescendo Xenomorph said:
so the problem is Samdung's QC....
anyway no more somedung, I switched to Xiaomi Mi Mix, still preordering from China.....
Click to expand...
Click to collapse
That's OK, I can scan and remove all those spyware.
Still its better to have it properly supported with actual updates (older phone still got all UI + android update, hello MIUI 8).
Rather than using phone without proper software support....
Tab S - buggy and prolly the last MM update
Note 3 - useless LL update, very unstable, consider alpha
Note 8.0 - buggy last KK update, switched to CM13 and happy with it

Samsung Galaxy Tab 3 8.0 (SM-T311) not charging: troubleshooting help needed

Hi there,
I have received this Galaxy Tab 3 (SM-T311) and it does not turn on nor charge.
I have tried the various suggested button presses, I have tried unplugging the battery for a while. Now I am leaving it to charge but this was already tested by the previous owner with no success.
I would like to find out if charger circuit, battery or motherboard need replacement.
I have tested with a multimeter that battery leads show 3.7V - with charger plugged or not. With battery removed the leads show a value of 0.4V.
Can somebody help to figure out whether it is a battery problem, a charger circuit problem or a motherboard problem? I think it might be one of the first two since battery charge should not be so low.
Thanks
By the way, I have already been through this video: https://www.youtube.com/watch?v=m2VJ_VRIRSI
Which comes from this blog post: http://www.bigpicturebigsound.com/Samsung-Galaxy-Tab-3-Won-t-Charge-or-Turn-On---How-to-Fix.shtml
I am not using the original charger and cable but a 2A one, sorry but I do not believe that the original USB cable and PSU would be any different it's like with HDMI, it's a standard. The only thing that could change is the power intensity which is 2A as per original.
hyklamin77 said:
By the way, I have already been through this video: https://www.youtube.com/watch?v=m2VJ_VRIRSI
Which comes from this blog post: http://www.bigpicturebigsound.com/Samsung-Galaxy-Tab-3-Won-t-Charge-or-Turn-On---How-to-Fix.shtml
I am not using the original charger and cable but a 2A one, sorry but I do not believe that the original USB cable and PSU would be any different it's like with HDMI, it's a standard. The only thing that could change is the power intensity which is 2A as per original.
Click to expand...
Click to collapse
Sorry I can't help, except to say it sounds just like my problem. I'd been using mine mainly as a clock/alarm clock using a great alarm app. The battery was good enough to last about 15 or more hours with a clock display on, but then I left for a 2 week vacation, and decided to turn the tablet off rather than leave it on a charger. Came back and it was dead.
I also did all sorts of button presses, used various chargers and cables (I have the original charger, which works for other devices, but didn't help). I disconnected the battery for several hours. Tried charging off a computer USB-2 port. etc, etc. Still, "It's dead, Jim".
I suspect it's the battery, which is pretty old now, and has been left on the charger a lot lately, though not 24 hours a day. Lithium batteries don't like to go totally dead, but I guess that's what happened. If the tablet were still useful to me, I'd try a cheap one from Amazon, not really expecting it to last a long time, but useful to see if it works without losing too much.
I've seen one repair tech who fixed a similar problem by disconnecting the battery and connecting it to a power supply briefly to give the battery enough of a charge to get the phone to start charging it normally. Obviously, this is something that mere mortals would not be able to do.

Categories

Resources