You guys are my last hope!
I can only get into Download mode, I can not go to my recovery using the hardware button combo. Flashing kdz files with lgup doesn't work because my device model is "unknown" therefore I can't get to the actual flashing.
The 2014 flash tool is telling me that the installation failed due to an error.
I currently have no internet at home so it can take a while until I can answer. Currently stealing McDonald's Wi-Fi trying to unbrick my phone :good:
Hello, (complete n00b here)
Several days ago I've tried to flash a 6.0 MM (from 5.1) to my LG G4 H815 phone. There was no option to do it automatically so I proceded to do it manually via flashboot.
I hard-bricked it to oblivion as in black screen, no response whatsoever.
While investigating @ the internet I've managed to understand I could get it fixed via quadcomm drivers (mode 9008).
Tried various "fixes" for H815 but was getting safari download errors. For some reason I tried a LS991 fix and it worked. When I started the phone it showed no logo but just a secure booting error 1006.
Still, could enter firmware download so I began to flash a lot of KDZ firmwares with no success.
LGUP shows my model : H81510H.
While in fastboot mode there is a note below (wasn't there the first time) with codes : 633 B46 or something like that.
While flashing anything it ALWAYS STOPS at 9% with a tot anti-rollback error. While flashing the code changes briefly where one can read smth like : LGLS991ZVA ver. 6.0
Managed to download some KDZ for that exact model, SAME ERROR. Tried to find / flash LS991ZVA with no success in finding a TOT file.
Also, managed to get ADB drivers up and it shows unauthorized in listing (LS991). Fastboot does not detect my device even in fastboot mode @ phone.
Please HELP!
Longbranch said:
Hello, (complete n00b here)
Several days ago I've tried to flash a 6.0 MM (from 5.1) to my LG G4 H815 phone. There was no option to do it automatically so I proceded to do it manually via flashboot.
I hard-bricked it to oblivion as in black screen, no response whatsoever.
While investigating @ the internet I've managed to understand I could get it fixed via quadcomm drivers (mode 9008).
Tried various "fixes" for H815 but was getting safari download errors. For some reason I tried a LS991 fix and it worked. When I started the phone it showed no logo but just a secure booting error 1006.
Still, could enter firmware download so I began to flash a lot of KDZ firmwares with no success.
LGUP shows my model : H81510H.
While in fastboot mode there is a note below (wasn't there the first time) with codes : 633 B46 or something like that.
While flashing anything it ALWAYS STOPS at 9% with a tot anti-rollback error. While flashing the code changes briefly where one can read smth like : LGLS991ZVA ver. 6.0
Managed to download some KDZ for that exact model, SAME ERROR. Tried to find / flash LS991ZVA with no success in finding a TOT file.
Also, managed to get ADB drivers up and it shows unauthorized in listing (LS991). Fastboot does not detect my device even in fastboot mode @ phone.
Please HELP!
Click to expand...
Click to collapse
H81510h is os version it is still at 5.1 I think....what may help is plug your phone in with lgup and drop the battery out of it then closes of LG up put battery back in and start LG up and find kdz that matchs your phone and make sure that it doesn't have anti rollback.....
stinka318 said:
H81510h is os version it is still at 5.1 I think....what may help is plug your phone in with lgup and drop the battery out of it then closes of LG up put battery back in and start LG up and find kdz that matchs your phone and make sure that it doesn't have anti rollback.....
Click to expand...
Click to collapse
Hello and thx for reply. I tried to do what u've said. It did something (I was looking for a while back). When I plug the cable back in, my windows 7 immediately installs quadcomm hs-usb driver (9008) and my phone acts as if it was dead. LGUP cannot find it in that state. I've been trying to QFIL the "proper" soft but it continues to pop different errors (using different QFIL versions). Either saharafail or some sort of download fail.
LGUP still presents an error (if I decide to "fastboot" it) @ 9% 0x2000, TOT antirollback version is smaller than device version.
How can I make sure I've got the proper KDZ without ANTI-ROLLBACK?
Longbranch said:
Hello and thx for reply. I tried to do what u've said. It did something (I was looking for a while back). When I plug the cable back in, my windows 7 immediately installs quadcomm hs-usb driver (9008) and my phone acts as if it was dead. LGUP cannot find it in that state. I've been trying to QFIL the "proper" soft but it continues to pop different errors (using different QFIL versions). Either saharafail or some sort of download fail.
LGUP still presents an error (if I decide to "fastboot" it) @ 9% 0x2000, TOT antirollback version is smaller than device version.
How can I make sure I've got the proper KDZ without ANTI-ROLLBACK?
Click to expand...
Click to collapse
This may help........
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
stinka318 said:
This may help........
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
Click to expand...
Click to collapse
Thx again. Uppercut shows H81510H as LGUP did. Is it possible that it's somehow write-protected?
It confuses me, since during the firmware update on my phone, I get this small box below the picture showing wierd codes : 633A Bxx and when I'm trying to flash my phone, the code gets longer with LS991ZVA v6.0 and more other. It then stops.
Funny thing is, when I got the phone I couldn't even connect to the LG bridge to update it at all. I've managed to do it bugging the MTP protocol but THAT on the other hand prevented me from copying stuff / FLASH my phone to MM 6.0. Had to factory reset it back then and all went back to "normal" = LG couldnt detect my device but I could copy photos or stuff from it.
NOW, when my phone is bricked, LGbridge DETECTS my phone (in fastboot), downloads the newest KDZ update BUT cannot install it (same thing as in LGUP). Hence my question : is it somehow write-protected?
Longbranch said:
Thx again. Uppercut shows H81510H as LGUP did. Is it possible that it's somehow write-protected?
It confuses me, since during the firmware update on my phone, I get this small box below the picture showing wierd codes : 633A Bxx and when I'm trying to flash my phone, the code gets longer with LS991ZVA v6.0 and more other. It then stops.
Funny thing is, when I got the phone I couldn't even connect to the LG bridge to update it at all. I've managed to do it bugging the MTP protocol but THAT on the other hand prevented me from copying stuff / FLASH my phone to MM 6.0. Had to factory reset it back then and all went back to "normal" = LG couldnt detect my device but I could copy photos or stuff from it.
NOW, when my phone is bricked, LGbridge DETECTS my phone (in fastboot), downloads the newest KDZ update BUT cannot install it (same thing as in LGUP). Hence my question : is it somehow write-protected?
Click to expand...
Click to collapse
Have you tried to eset it by pushing power and volume own then when you see bootsplash then release power button and hen quickly push the power button again....
But in your case push power and volume down within the count or 20 then release power then push power button again and see what happens and then try the same thing on volume up......
Thanks for the reply.
I did what u've said. Despite no logo I tried to release power button for a second just after the screen's brightness goes up (I also get a small vibration @ start). Everytime I get secure booting error 1006 after a few seconds.
On the other hand when I did that with volume UP button there was no error but there was nothing aswell until I release power button in which case I got the secure booting error. All of the above tries were done with no USB connection with anything.
Longbranch said:
Thanks for the reply.
I did what u've said. Despite no logo I tried to release power button for a second just after the screen's brightness goes up (I also get a small vibration @ start). Everytime I get secure booting error 1006 after a few seconds.
On the other hand when I did that with volume UP button there was no error but there was nothing aswell until I release power button in which case I got the secure booting error. All of the above tries were done with no USB connection with anything.
Click to expand...
Click to collapse
Do try with usb s well it may do something r do nothing......
Can't tell atm since I gave it to professionals. I'll wait and see how it'll turn up. Thx for all the effort tho, was nice to tinker with a lil help
@Longbranch did you solve this problem ? I'm in the same state but my phone model is H810, everything else is the same as yours.
Nope, not really. I gave it back to the reseller and my money got returned luckily.
The professionals I refer to above did install a specific firmware for the ls991 type. Firmware ZVB I think. The only one appliable apparently. Anyways, as I suspected the ls991 type is for the US and therefore it didn't work in my country in EU. My sim card wouldnt work with it. Besides, without the sim card, the phone decided to freeze and die after several minutes every time I turn it on. Swapped for LG G5 and it's working flawlessly up until this day.
good for you, what i don't understand is that it's a h810 model but now identify as ls991 does that mean you can convert it just by a Qfil flash? I may try another model flash if can't find a suitable Rom for it
Longbranch said:
Nope, not really. I gave it back to the reseller and my money got returned luckily.
The professionals I refer to above did install a specific firmware for the ls991 type. Firmware ZVB I think. The only one appliable apparently. Anyways, as I suspected the ls991 type is for the US and therefore it didn't work in my country in EU. My sim card wouldnt work with it. Besides, without the sim card, the phone decided to freeze and die after several minutes every time I turn it on. Swapped for LG G5 and it's working flawlessly up until this day.
Click to expand...
Click to collapse
Chebhou said:
good for you, what i don't understand is that it's a h810 model but now identify as ls991 does that mean you can convert it just by a Qfil flash? I may try another model flash if can't find a suitable Rom for it
Click to expand...
Click to collapse
Yes! That's what I and neutrondev telling everyone :
do not use qfil without the knowledge about the result!
The only working firehose file available out there is for the ls991 and that means if you use it it will turn your device into a ls991 without any way to get back to your previous device model!!
.
Sent from my LG-H815 using XDA Labs
@steadfasterX since I have done it already is there any way to get it working even as an LS991 ?
here is what i did till now
the reason for using Qfill is that it went dead after flashing an H810 rom .
after that when it's in download mode it doesn't allow me to flash the ls911ZV5 ls911ZV6 ls911ZV6_12 roms that i found ( it says LS991ZVA )
so i went in fastboot and flashed boot/aboot/recovery....img extracted from the ls911ZV6 rom then it accepted the rom in download mode
but it is stuck in a hard bootloop ( reboots when it is getting in recovery but still has download mode yet no fastboot as before)
any thoughts ?
Chebhou said:
@steadfasterX since I have done it already is there any way to get it working even as an LS991 ?
here is what i did till now
the reason for using Qfill is that it went dead after flashing an H810 rom .
after that when it's in download mode it doesn't allow me to flash the ls911ZV5 ls911ZV6 ls911ZV6_12 roms that i found ( it says LS991ZVA )
so i went in fastboot and flashed boot/aboot/recovery....img extracted from the ls911ZV6 rom then it accepted the rom in download mode
but it is stuck in a hard bootloop ( reboots when it is getting in recovery but still has download mode yet no fastboot as before)
any thoughts ?
Click to expand...
Click to collapse
Yes it's possible. You can boot a h811 H815 or any other rom you like. Even LOS!!
Great right? BUT you are bounded to the ls991 modem and so you need to be in a sprint network to use telephony. That means the phone is now useless outside the US .
And you wrote you tried ls911 ROMs? I hope you meant ls991
I work on a fully working experience on every network though. Checkout my proof of concept for unlocking the bootloader thread
I can go into details on IRC if you like.
..
Sent from my LG-H815 using XDA Labs
@steadfasterX thank you for keeping up with me ! ( btw what room on IRC ?)
for now I have used Qfill again and got fastboot working again and flashed TWRP ( not sure where ! ) so when the phone is off and i plug the usb it boots to twrp ( but it doesn't in recovery )
normal boot will show "secure boot error 1002"
then i flashed twrp img to recovery partition using twrp but it didn't work in recovery ( still reboots after showing Recovery Mode loading screen )
also tried to load some roms on the device to try them but I got error "file too large for filesystem " when copying them .
atm I don't know the state I'm in and what should be next ?
btw here are the recovery log and dmesg
Chebhou said:
@steadfasterX thank you for keeping up with me ! ( btw what room on IRC ?)
for now I have used Qfill again and got fastboot working again and flashed TWRP ( not sure where ! ) so when the phone is off and i plug the usb it boots to twrp ( but it doesn't in recovery )
normal boot will show "secure boot error 1002"
then i flashed twrp img to recovery partition using twrp but it didn't work in recovery ( still reboots after showing Recovery Mode loading screen )
also tried to load some roms on the device to try them but I got error "file too large for filesystem " when copying them .
atm I don't know the state I'm in and what should be next ?
btw here are the recovery log and dmesg
Click to expand...
Click to collapse
Np we can bring you back to life but as already said without cell service. That's the price for the firehose and unlocked feeling you have now.
Did you found and read my thread here?
https://forum.xda-developers.com/g4/general/bl-unlock-unlock-bootloader-proof-t3648288
There you will find some more info and also the IRC details how you can find me. I'm online from Monday to Friday mainly.
It's much easier to talk in chat then here. once all the details are known I will provide a full guide.
.
Sent from my LG-H815 using XDA Labs
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Solution
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I've used MiFlash Tool, and the problem was fixed. Sahara Error occurs when you take to much time to flash after booting to EDL, you only have few seconds to flash util the port is closed for writing. QFIL takes around 20 to 25 seconds in caching the files so use MiFlash and It'll flash. Best way to do it is:
1. Install and setup MiFlash for flashing.
2. Open MiFlash and select your Firmware's folder.
3. As soon as you connect the phone refresh miflash and hit flash.
If everything goes well you'll flash will be successful else try again.
I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.
Chin_hebbar said:
I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.
Click to expand...
Click to collapse
I need to flash Baseband for Oreo. Please guide me
windows 10 problem
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I face this problem in windows 10.
first uninstall zuk drivers and qfill and disable driver signature enforcement (Google it how to do it) then install zuk drivers and qfill use original cable and your phone will get flashed
Balaji Sriram said:
I need to flash Baseband for Oreo. Please guide me
Click to expand...
Click to collapse
Follow the instruction from this post
https://forum.xda-developers.com/lenovo-zuk-z2/how-to/zuk-z2-baseband-flashing-guide-t3715121
Do not listen to anyone telling you to use miflash, only use qfil otherwise you WILL encounter other issues because qfil is the only way to reach the deeper partitions that mi is unable to... Other issues may range from no volte, calling or signal problems etc its just easier to do it right the first time.
getting the error message "KERNEL REV. CHECK FAIL DEVICE: 12 BINARY: 5 (BOOT)"
can someone help me out here?
got a bricked s20 (G981BXXU5CTL1 H3G)
only able to go into download mode or boot loop
Recovery mode does not open
Tried installing TWRP when this showed up
I tried several times to flash factory firmware
anybody know what the error message means and how I can unbrick my phone?
Edit: nvm I got it
btw. I cant seem to find firmware with my csc: H3G
and my Odin seems to be stuck on super.img when trying to flash AP
please help me out if you can ty
I’ve tried everything I know how to do. What I did was used msm tool to get a stock rom back and it worked so I then use fastboot enhanced to flash upgrade so to say and what I did was I switched the partition from B TO A so I think I overwrote the main boot partition. Well anyhow that failed. I’ve the QPST firmware for snapdragons and can’t get it out of download mode. I’ve tried so many variants including the Indian ver. I don’t know why that varient works more than others but I’m stuck in a bad way. I have bricked my phone before and sent it back to company only for them to tell me it can’t be fixed. I fixed it within and hour of them sending back but this is a new issue. Stuck in EDL. And msms just get Sahara comm error and I’ve done all the trouble shooting for that scenario. Heeeeeeeeeelp. Please. Lol
Fixed. I read some post somewhere and as I started playing with those combos it wasn’t the one I had done but it is the Indian version that it for some reason but here it is.
MSM mode :
Target = India
sha256 = off
chek - use lite firehose