Related
I just got my Incipio Feather in the mail, and I must say I am very let down. When I looked at the picture on the website, I really thought that the case was going to wrap around the front but it does not. In all fairness, I did look at the picture again and it doesn't wrap around in it like I thought it did. The picture is very deceiving, the way they shade the Evo makes it look like the case wraps around, at least to me it does. Anyways...
The Incipio is a lot thicker than the Barely There, and doesn't come up as high on the sides either. That actually makes it feel rather awkward in the hand because there is a very pronounced lip around the whole phone. Also, the Incipio case has a full cutout, like a bite, from the front of the case for the volume rocker whereas the Barely There has a rectangular hole and covers the plastic in front of the rocker.
The Incipio also provides far less protection for the camera lens. With the Barely There, the lens is completely protected, it covers the edge of the glass, fully recessing the lens into the case. It has a separate cutout for the flash, lens, and speaker. The Incipio just has one gaping hole for all three to share.
My biggest complaint about the Incipio is that because it doesn't come up all the way around the sides, the face of the Evo sticks out from it and consequently the corners are not fully protected. If this thing takes a tumble on to concrete, there is a good chance your corner could still get scratched. With the Barely There case, while still not very protective, at least your corners won't get beat up.
The only positive about the Incipio is that I like the way the material feels better than the Barely There. It has a softer, almost velvety finish to it. The Barely There still has a nice rubberized texture to it, just not as nice as the Incipio's.
I see no reason at all to purchase the Incipio case when you can buy the Barely There case instead. The Barely There is thinner, feels more comfortable in the hand, and provides more coverage/protection. I am sticking with my Barely There case and will probably give the Incipio away.
Casemate Barely There
Incipio Feather
Both cases cost $19.99.
Thanks for the review ... appreciate it. Have you looked at the other Case Mate Evo case that is two part (Tough Case)? Just wondering about the protection and quality.
No I haven't, at least not in person. I'm sure it's a great case, and I know other people have had good experiences with it, but I personally don't like the way it looks compared to the OB Commuter case or the Seidio Active Limited, and I already have both of those.
_MetalHead_ said:
No I haven't, at least not in person. I'm sure it's a great case, and I know other people have had good experiences with it, but I personally don't like the way it looks compared to the OB Commuter case or the Seidio Active Limited, and I already have both of those.
Click to expand...
Click to collapse
Couple of quick questions for you ... since you have both. I had the Seidio Active Limited from Amazon, really liked the feel of it, but the plastic back began to peel off. I didn't replace it with another ... afraid the same thing would happen. Any issues for you? So I've been using the Otter Box Impact case, but since I keep my phone in my front pocket ... it can be a lint magnet. If you don't mind ... tell me about your experience with the Commuter case from OB. Thanks.
wmdunn said:
Couple of quick questions for you ... since you have both. I had the Seidio Active Limited from Amazon, really liked the feel of it, but the plastic back began to peel off. I didn't replace it with another ... afraid the same thing would happen. Any issues for you? So I've been using the Otter Box Impact case, but since I keep my phone in my front pocket ... it can be a lint magnet. If you don't mind ... tell me about your experience with the Commuter case from OB. Thanks.
Click to expand...
Click to collapse
I have the exact same issue as you with the Seidio. I have actually gone through 3 of them now, and they all started peeling within a week. The first one I had one of the tabs broke off while putting the case on. It's a shame that the build quality is so crappy on them because I really like the design, and I think it's a little more rugged than the OB Commuter. Not by much though, it just has thicker silicone.
My only complaint about the Commuter, and I know a lot of people share the same feeling, is that the cover for the charging and HDMI ports was poorly designed. It is a pain to get it closed, and it never stays in place for very long. Also, the way they cut the silicone for that cover, it is subject to tearing. Mine hasn't torn, and neither has my buddy's, but I know some people have had that issue. The good news is that Otterbox, unlike Seidio, has no problem whatsoever sending out a replacement case if by some chance that piece tears off, or any other defect for that matter. Overall I think it is a great case and I use it regularly, and even with the small issue of that cover, I can still recommend it to people.
Thank you ... I'm thinking about trying the "Barely There" since I'm an "in pocket" guy.
You can barely tell that there is a case on the phone with the Barely There, hence the name. If you're an in pocket guy, then that is definitely the case you want. I use it way more than all my other cases combined.
get the barely there case, i have it and love it, and as they say, its hardly noticable. plus case-mate came out with a full frontal screen cover, so you have case protection on back and sides and a full screen cover to cover the remaining parts
wmdunn said:
Thank you ... I'm thinking about trying the "Barely There" since I'm an "in pocket" guy.
Click to expand...
Click to collapse
You said my words exactly. I too am very let down with the Incipio Feather case. I also thought that it would at least have a lip that came over the front edge but nothing. I dropped my phone on the carpet(fortunately it was carpet) and it popped right out of the case. If you want protection I don't think this is the case to use. They could have done much better. I would have preferred one of the Incipio NGP cases to this thing.
I've been using the Barely There case for almost 2 months. I love the feel of it. The material holds well. The screen protector it came with is awesome. I hated the way stealthguards and invisible shield felt on the glass. The screen protector that the Barely There came with feels just like glass when it's on.
The only thing is that this case is just to protect against scratches and minor drops on carpet maybe. I dropped it once on concrete and the case flew off and I have a small dent on the top front corner of my Evo.
This is my experience exactly
dcfella said:
I've been using the Barely There case for almost 2 months. I love the feel of it. The material holds well. The screen protector it came with is awesome. I hated the way stealthguards and invisible shield felt on the glass. The screen protector that the Barely There came with feels just like glass when it's on.
The only thing is that this case is just to protect against scratches and minor drops on carpet maybe. I dropped it once on concrete and the case flew off and I have a small dent on the top front corner of my Evo.
Click to expand...
Click to collapse
I have the Seidio Rugged and it comes with the Innocase Surface as well and I really like the Surface, its not too thick and protects the camera lenses from scratches. I just need to get the belt clip for the Surface so outside of work I don't have all the bulk.
Sent from my PC36100 using XDA App
Get the Otterbox Impact. I love it. High quality silicone and nice thick screen protector.
Sent from my PC36100 using XDA App
Those aren't really barely there cases
xlGmanlx said:
Those aren't really barely there cases
Click to expand...
Click to collapse
Barely there cases are counter-intuitive. If you want to protect a case against impact should you drop it, the case needs to be heavy enough to absorb most of the impact itself and not the phone. These barely there cases may protect from scratches on the phone body but that's it. So I guess you can safely slide the phone around on your desk but don't drop it.
Sent from my PC36100 using XDA App
Case mate barely-there case on newegg for $9.99. I would post the link but I don't have 8 posts yet.
Not really applicable in a thin case review check op as the subject isn't the merits of thin cases versus other types
mitchellvii said:
Barely there cases are counter-intuitive. If you want to protect a case against impact should you drop it, the case needs to be heavy enough to absorb most of the impact itself and not the phone. These barely there cases may protect from scratches on the phone body but that's it. So I guess you can safely slide the phone around on your desk but don't drop it.
Sent from my PC36100 using XDA App
Click to expand...
Click to collapse
the bottom flap on my commuter stays in place fine, also fits great in your pocket, unless your female and wear them skin tight the barely there doesn't have any lay on the table protection for the front glass, which is just too risky in my opinion.
Sent from my PC36100 using XDA App
Poetik said:
Case mate barely-there case on newegg for $9.99. I would post the link but I don't have 8 posts yet.
Click to expand...
Click to collapse
Thanks, just order it. I had the ID case for the iPhone from them and that thing took a beating and never gave up. Hope to expect the same from them again
I still think the Otterbox Commuter is the best case out there. It doesn't add that much bulk, feels sturdy and protects like none other. Well worth the money.
Yep, I'm starting another Evo 4g case thread. Mainly due to the fact that I can't find any decent reviews on the new Ballistic SG.
I've pretty much ruled out the Otterbox Defender and Ballistic HC because they seem a little more bulky than I want and overkill.
(link removed)
I'm aware of the Otterbox Commuter's issues with the silicone port cover coming off. I held the case and it just seems a little unsubstantial to me. The silicone seems very thin and the hard case is adequate but still seems very thin as well. I've also read a lot of complaints about the silicone deforming and not fitting the phone well after a short time.
(link removed)
The CaseMate Tough Case seems a little more substantial but I can't tell how thick/thin it is from the pictures. The corners seem better protected than the Commuter but there are no port covers.
(link removed)
I can't find any adequate reviews of the Ballistic SG case. It seems a little beefier than both of the others. I've heard the kick stand is a flimsy POS (if it's the same as the Ballistic HC) but I don't mind snapping it off and using the stock one. There are also no port covers with this one. Their customer service seems a little lacking so I don't know about support/warranty issues.
(I can't post links to the cases which is pretty annoying)
Does anyone have any updated information to share on these cases? I searched the forum but couldn't find anything current, especially on the Ballistic SG.
I too am looking for more information or detailed review of the Ballistic SG. Thakx in advance.
The Ballistic SG looks to basically be like the inner layer of the HC, but with a more finished look. It looks like the kickstand is the same. The kickstand on my HC has held up well, it isn't flimsy at all.
Sent from my HTC EVO 4G with Tapatalk
kd0axs said:
The Ballistic SG looks to basically be like the inner layer of the HC, but with a more finished look. It looks like the kickstand is the same. The kickstand on my HC has held up well, it isn't flimsy at all.
Sent from my HTC EVO 4G with Tapatalk
Click to expand...
Click to collapse
Except that the very most inner layer of the SG is silicone instead of the outermost layer of the HC. Does the HC case have anything soft inside next to the phone to protect it or do you think the inside could possibly rub the paint off the phone eventually?
How do you like the built in screen protector of the HC? Is it better than a stick on if you've used one of those?
I totally forgot about not having to use the outer layer of the HC which would be good to take that off and stick the phone in my pocket. It looks like the most versatile case.
The only thing about the SG is it has the inner silicone which also servers as the corner bump guards.
I'm still torn. lol
The HC isn't lined with silicone, but it does have "shock absorbent polymer" on both the inside and outside of the inner case. The hard plastic does not touch the phone so there's no need to worry about it getting scratched. The corners are also well protected.
The built in screen protector is the only thing I didn't like about the HC. I actually removed it from the case and I am using a regular protector on my screen.
Sent from my HTC EVO 4G with Tapatalk
I was leary if the HC because of the built-in screen protector. I has been waiting months for the release and actually bought the Seidio Innocase Rugged instead. After a couple months I bought the HC simply cause I wanted something new. The screen protector is actually great and feels natural with no loss of function.
stanglifemike said:
I was leary if the HC because of the built-in screen protector. I has been waiting months for the release and actually bought the Seidio Innocase Rugged instead. After a couple months I bought the HC simply cause I wanted something new. The screen protector is actually great and feels natural with no loss of function.
Click to expand...
Click to collapse
Are you also using the inner adhesive screen protector? I read the outer protector could show air bubbles if not used with the inner one.
A big concern of mine with the HC is the plastic cover around the front rim that covers the prox sensor near the ear piece. I also read that some people have had problems with this. The manufacturer may have resolved this by now.
I have the Ballistic HC case with the screen protector that came with it. No bubbles here. The cover for the 3.5mm is a little bit floppy, but otherwise ok. I haven't had any issues wit the proximity sensor. Overall, the case is good. I paid $30 at Amazon for it.
sqwerl said:
Are you also using the inner adhesive screen protector? I read the outer protector could show air bubbles if not used with the inner one.
A big concern of mine with the HC is the plastic cover around the front rim that covers the prox sensor near the ear piece. I also read that some people have had problems with this. The manufacturer may have resolved this by now.
Click to expand...
Click to collapse
I'm using a Zagg screen protector and did get the oil slick look. The cabby powder trick works to cure that though. I am about to try the protector that came with it and see if that helps. No issues with the proximity sensor here though. I love it though, no complaints from me.
I have the red Ballistic HC case. Love it, but I have the proximity sensor issue. Is there a fix, or should I call Ballistic and try to get a new case?
Sent from my rooted EVO 4G running Myn's Warm 2.2 ROM, using Tapatalk.
I have an Otterbox Commuter (Bought 11/1 Last Year) and it works great. I cut the port cover off the bottom a couple months after I got it because it took too much fidgeting with it to get it to close right and I did not really need it.
The headphone cover on top is also getting pretty close to getting removed since it is an annoyance to have to open/close it all the time when I need it. It does not flip open like the bottom port cover did, but I just don't find that I need the extra protection for the ports on the phone.
Blkdimnd,
I don't know of a fix. Is the plastic raised a bit over the speaker and proximity sensor? Mine wasnt snapped together all the way at the top one time and I had that issue, but it was my fault. You could try bending the front cover so it bows in, instead of out, if that is your issue. Other than that, call Ballistic and see what they say.
Im trying to find reviews on the Ballistic SG myself... Seems good so far in terms of form factor as compared to the HC and Defender. I might end up purchasing it !!!
I own an Otterbox Commuter for my HTC EVO 4G and it is my second case. My first case was a simple and very inexpensive Amzer black silicone case that did the job of saving the phone's battery cover and camera lens from wear and tear for the first few months. After a friend purchased the Commuter and spoke highly of it and my Amzer case started to fit poorly -- likely my fault from removing it too many times -- I felt the need for something a bit more substantial. I bought the Commuter for around $30 in January and, nearly two months later, I must say that I'm pleased with my second case.
I agree that the silicone port cover feels flimsy. However, the cover shows no signs of ripping and I recharge my phone daily, resulting in heavy use of the cover. It would be great had Otterbox designed the port cover similar to the headphone jack cover, e.g., a cover that fits inside of the ports themselves, preventing them from opening on its own. Nevertheless, I understand why this may not have been practical: the ports are tiny as compared to the headphone jack port and appear to be more delicate.
I love the hard shell that covers that back of the phone. I purchased an inexpensive silicone mat for my car to keep the phone from sliding around on my center console; my first silicone case kept the phone from sliding on much of anything. The silicone inner shell and the hard outer shell easily protect the phone's camera and the screen.
My biggest gripe about the Commuter was the lackluster screen protector. It was great that the case came with a screen protector; it wasn't so great that the screen protector had numerous scratches after only one week of use. I replaced it after two or three weeks with a REALOOK premium screen protector, which comes with two (2) screen protectors and applied more easily than the one included with the case. Thus far, the REALOOK screen protector is holding up much better than the one included with the case and I have a second one to replace the first if it starts to show excessive signs of wear.
I can't personally compare the Commuter with any of the other cases in which you're interested but will personally vouch for the Otterbox Commuter. For $30, I feel that it does a better than adequate job of protecting my phone and it's so much nicer looking than most of the ones that friends and co-workers use for their phones, EVOs or not.
matthewdavisnelson said:
I own an Otterbox Commuter for my HTC EVO 4G and it is my second case. My first case was a simple and very inexpensive Amzer black silicone case that did the job of saving the phone's battery cover and camera lens from wear and tear for the first few months. After a friend purchased the Commuter and spoke highly of it and my Amzer case started to fit poorly -- likely my fault from removing it too many times -- I felt the need for something a bit more substantial. I bought the Commuter for around $30 in January and, nearly two months later, I must say that I'm pleased with my second case.
I agree that the silicone port cover feels flimsy. However, the cover shows no signs of ripping and I recharge my phone daily, resulting in heavy use of the cover. It would be great had Otterbox designed the port cover similar to the headphone jack cover, e.g., a cover that fits inside of the ports themselves, preventing them from opening on its own. Nevertheless, I understand why this may not have been practical: the ports are tiny as compared to the headphone jack port and appear to be more delicate.
I love the hard shell that covers that back of the phone. I purchased an inexpensive silicone mat for my car to keep the phone from sliding around on my center console; my first silicone case kept the phone from sliding on much of anything. The silicone inner shell and the hard outer shell easily protect the phone's camera and the screen.
My biggest gripe about the Commuter was the lackluster screen protector. It was great that the case came with a screen protector; it wasn't so great that the screen protector had numerous scratches after only one week of use. I replaced it after two or three weeks with a REALOOK premium screen protector, which comes with two (2) screen protectors and applied more easily than the one included with the case. Thus far, the REALOOK screen protector is holding up much better than the one included with the case and I have a second one to replace the first if it starts to show excessive signs of wear.
I can't personally compare the Commuter with any of the other cases in which you're interested but will personally vouch for the Otterbox Commuter. For $30, I feel that it does a better than adequate job of protecting my phone and it's so much nicer looking than most of the ones that friends and co-workers use for their phones, EVOs or not.
Click to expand...
Click to collapse
I appreciate the feedback. I just realized the Ballistic SG also doesn't come with a screen protector. While the one that came with your Commuter may not the best, I suppose it's still better than nothing if comparing it to the other case.
Quite a few people haven't really had a problem with the port cover like you say and if someone wants a case to be indestructible then you probably need to get a Defender.
Just for comparison these are the dimensions I got directly from Ballistic.
Ballistic said:
Thank you for your interest in the HTC Evo Ballistic HC case. Here are the dimensions you requested.
Dimensions in the Gel, including holster:
X – 85.34mm (3.36in)
Y – 145.91mm (5.74in)
Z – 42.47mm (1.67in)
Dimensions in the Gel, No Holster:
X – 81.69 mm (3.22in)
Y – 135.63mm (5.34in)
Z – 24.75mm (0.97in)
Here are the Dimensions for the Shell Only:
X – 77.59mm (3.05in)
Y – 131.27mm (5.17in)
Z – 21.99mm (0.87in)
Here are the dimensions of the HTC Evo Ballistic SG case.
X – 75.97mm (2.99in)
Y – 131.40mm (5.17in)
Z – 22.48mm (0.89in)
Click to expand...
Click to collapse
What I don't understand is if the SG is supposedly thinner than the HC it doesn't appear that way by the dimensions, unless that takes into account the curvature and the "lay on table" feature of the SG.
One reason I haven't already snatched up the SG is the cost. It looks like no one besides Ballistic is selling it so I can get an HC on Amazon cheaper.
I love my otterbox case because it is big and fits in my hands
I used the commuters for many months and never had a problem with the bottom port cover. in fact, that was one of my favorite things about the case. i was impressed how well it stayed in, considering all the hating I had read about it.
Sent from my PC36100 using XDA Premium App
I ended up buying a Ballistic HC. For the price, I couldn't beat it. Ballistic is charging $7.95 for shipping so the total on the SG would be around $43 when there are HCs on Amazon all day for a lot less. That's with no screen protector or you can buy a $10 screen protector and get free shipping for an order over $40. Still pricey for such a simple case that I haven't seen any reviews whatsoever on.
Besides price it came down to buying a case with or without a silicone boot. Every complaint I've heard about silicone is stretches out and I didn't want to have to constantly take the boot off my phone to remove dust and lint. I have a silicone cover on another device and it has some terrible scratches all over it from all the trash accumulating. The HC seemed ideal since the silicone layer is optional and has an attached screen protector which pretty much seals it off.
I love the semi-soft material over the inner hard shell. It's firm enough not to move around but soft enough to stick fairly well to most surfaces. It slides easily in and out of my pocket.
The power and volume buttons have a very solid feel.
I was surprised that having an inner and outer screen cover didn't make it any more difficult to register touching the screen.
My biggest gripe about the case is the terrible kickstand. It doesn't snap down very snugly and once you snap it out, it swings very loosely. I thought about taking it totally off but then about 3/4 of the area under the kickstand is only covered by thin mesh for a flush fit. The Otterbox Defender kickstand is much more solid. I'll probably stick some tape under it to stop the rattle.
My second biggest gripe about the HC is some lint/dust still gets inside the case. I hope the case will always stay snapped together well after a lot of opening it to dust off the phone screen. The case snaps together like you almost need a crowbar to get it open!
Whereas the Otterbox Commuter's silicone port plug doesn't stay in place but the headphone plug is good, the exact opposite is true of the HC's silicone jacket. The port plug fits and stays but the headphone plug doesn't stay very well.
Since the top area of the case drops down to right about the screen viewing area, it's difficult to drag the status bar down without a little finesse.
All in all, I think all these trade-offs were pretty acceptable considering the price I paid.
I *LOVE* my Seido Innocase Surface II/Best Buy Platinum case. It's solid, adds very minimal to the "footprint", doesn't collect lint, and with a screen protector, gives me about 95% coverage (camera lens/leds/kickstand/ear port). It's held up remarkably well with removing it many times to change the battery too. Some cases wear out & become loose or whatnot. I have added a couple pieces of paper to keep the edges firmly seated, but it does fine without it.
I always forget to check, but when I did, I found several different colors on ebay for $19 shipped.
OtterBox
I've used the Commuter and the Defender both. IMO, the Defender is too bulky, but offers great protection. As for the Commuter, I really liked the syle and feel of the the case, but after 3 days took an Exacto knife and cut off the bottom silicone port cover (very poor design). After I did that, I was happy with it. I've dropped my phone several times on the tile in my house and the case provided great protection. The silicone does seem to stretch out after time, especially if you change out batteries often.
hi guys
i have been comparing these two products for a quite some time and i cannot give my final decision to which product should i buy. i am looking for a case that has a front face cover. and i found the ballistic maxx and otterbox defender. but what makes me think twice between these product is the comes with screen protector. these protector is quite think and most likely it will ruin the colors of my S3's screen. i have seen it in some product reviews posted by youtube users. the screen becomes glary. and the second thing that makes me think twice is, if i remove the screen protector, will my S3 shake around inside the case if i dont use the screen protector?
i tried contacting the customer support of otterbox they said they cannot answer my concern. and for ballistic they told me i can still use the case even if i dont use the screen protector, but i still do not understand what they really meant. and they did not gave me a straight answer to my question on what will really happen if i did not use their product's screen protector.
now i would like to ask your personal opinion about these two products, which is better? and if you guys did not use the comes with screen protector will your S3 shake around inside the case? and lastly i am just looking for a case that has a front cover. i dont really like the flip cover cases.
thanks
From what I read about the defender taking out the screen protector does not affect the snugg-ness of the phone and case.
I have the trident kraken that came with a removable screen protector, that I decided but to use.
Sent from Pluto.
I know how you feel, i looked at both those cases and went with the Trident Kraken. Provides the same level of protection and the kickstand is a bonus. Second choice would be the otterbox.
Sent from my SPH-L710 using Tapatalk 2
I personally hated the otter box, sold it as soon as I got the chance. I kept the maxx and it's the case I go for when I need a holster.
I took the screen protector off of my defender with no fit issues. I stopped using it because it squeeks so much. When you hold the phone. This may be due to extra flexing from the removed screen protector as it is rigid and glued in.
The otterbox is an awesome case, the only thing I hate is that the outer silicone layer always stretches out. The defender for my GS3 streched out after 2 months...
Sent from my SCH-I535
ricktat said:
I took the screen protector off of my defender with no fit issues. I stopped using it because it squeeks so much. When you hold the phone. This may be due to extra flexing from the removed screen protector as it is rigid and glued in.
Click to expand...
Click to collapse
I think it's just the case in general. My screen protector is still in tact and it squeaks like no other.
I'm tempted to get a new case, but can't decide. I've narrowed it down to the SG MAXX, Commuter, Kraken, PX260, and the Dualtek.
owlchemist said:
I think it's just the case in general. My screen protector is still in tact and it squeaks like no other.
I'm tempted to get a new case, but can't decide. I've narrowed it down to the SG MAXX, Commuter, Kraken, PX260, and the Dualtek.
Click to expand...
Click to collapse
I got the dualtek case yesterday, it's a really nice case. I just wish there was a compatible holster for it.
Sent from my SCH-I535
I have both cases mentioned in OP. The included screen covers are garbage. Make the screen look like crap plus particles such as sand, dirt (I am in construction field) and so on can get behind protector and scratch screen.
Standard zagg and otterbox working well for me. Zagg HD seemed to thin and marked up easy om my pocket. Otter box laps over the edge of the zagg, which so far has kept the edge from peeling on me which is a common problem for me and my use.
Ballastic has great rubber corners for drop protection but the otter box is easier to slip in and out of pocket and my preferred case.
Sent from my SPH-L710 using xda premium
naturecannon said:
I have both cases mentioned in OP. The included screen covers are garbage. Make the screen look like crap plus particles such as sand, dirt (I am in construction field) and so on can get behind protector and scratch screen.
Standard zagg and otterbox working well for me. Zagg HD seemed to thin and marked up easy om my pocket. Otter box laps over the edge of the zagg, which so far has kept the edge from peeling on me which is a common problem for me and my use.
Ballastic has great rubber corners for drop protection but the otter box is easier to slip in and out of pocket and my preferred case.
Sent from my SPH-L710 using xda premium
Click to expand...
Click to collapse
I also have both cases described in OP and have to agree to a point, the screen protectors make the screen look terrible. I went with the Ballistic for a couple reasons. 1. The Ballistic seems to slide in and out of my pocket easier (probably because it has more smooth surface than the Defender). 2. The belt clip seems more comfortable to me. The Defender belt clip seemed to sit higher on me which would gouge my hip. Not cool. 3. I got the Defender used when I bought my phone and the rubber on it seems a little loose. I don't think this will happen with the Ballistic mainly because my wife has one on her Note and it's help up extremly well. 3. I got my Ballistic Maxx on ebay for $30 in the color I wanted and I thought that was a good price. Now I need to ditch this screen protector and get a nice one.
I too have both cases. I did/don't use any of the screen protectors that came with it. As for OP, it really depends what you're trying to get out of it. What's your average day like? do you work in an office? go to school? work in construction? I am a process engineer and i'm in and out of food plants and i pull my phone out to snap pictures at least 4 times a day on a daily basis for an hour or so. With that being said I NEED the protection because I have dropped it a few times. I'm currently using the Ballastic without the clip, i just hold it in my pocket. The otterbox is a bit bulkier for me and it slips easy (from hand and in and out of pocket). The ballistic on the other hand, doesn't. It gives you good grip, and isn't a pain for me to pull out of my pockets (i wear dickies for work and rvca romero ii jeans when i'm out and about or jordan basketball shorts when i feel like bumming it). I like the grip because it doesn't slip out of my pockets easily when i wear basketball shorts as the ottorbox did. HOWEVER, be warned that it does pull lint easily. It's not alot where you'll get a hairball when you pull it out of your pockets but it is there. Overall, I'm sticking with the ballastic because it offers great drop protection (as does the OB), but with the corners I personally feel it's more secure and it's not as bulky as people say it is. I'll post up pictures when i get the chance.
Hi guys, I need a new case but have a couple questions about the causes I've narrowed it down to. I'm a student so I want to eliminate the need for having to buy another case if I dislike my purchase.
I have 2 tpu cases currently that were cheap at local cell shops.
The first one flexes too much where the volume rocker is so it causes my screen protector to bubble every time I press it. SUPER annoying.
The second seems to be somehow scratching the edges of glass that arent protected by my screen pro.
I'm guessing this case is a bit looser and has minimal movement and allows small particles to find their way in between the glass and the case.
I'm torn between two cases and I need some info on them that I havent been able to find reading the forums or from watching youtube reviews.
1) Incipio frequency: My main concern with this case is the sides flexing and causing my screen protector to bubble. Is there anyone that owns this case and can comment on this?
2) Seidio Surface: I've always wondered about just how snug these 2 piece cases are. Does the phone have enough space in the case that it is allowed to rattle at all? or is it just snug enough to keep the phone stable without scratching it?
COLES NOTES
-Need new case
-Incipio frequency or Seidio surface
-Will incipio case cause screen pro to bubble when volume rocker pressed
-Will seidio surface slowly scratch away at the aluminum finish/curved glass edges
All input is appreciated:cyclops:
So I'm writing this because of the "All input is appreciated"
Will you consider a third case? If so, take a look at the Trident Aegis case. You can find it brand new on eBay for $20 with shipping. I've used their cases before and they look extremely nice and on top of that, they do a good job with protecting the phones. I bought one brand new from eBay and I just got it today. It looks really top-notch. I'm waiting for my phone to come in. Hopefully I'll have it tomorrow so I can play around with it and give you some more feedback on Friday.
I've had the Seidio surface for over a month and so far no scratches on the glass or aluminum body. The inside of the case is soft with a carbon fiber sticker covering the inside. The phone fits snuggly but I can see a problem if you use a thick screen protector because of the tight fit.
All the cutouts are perfect with a nice beveled edge for the camera.
The case doesn't add a lot of extra bulk, which is the reason I got, I hate giant bulky cases.
Thanks for the replies guys!
I checked out the Triden Aegis but there's something about it I just didn't like.
I ended up ordering an incipio dual pro. I like the fact that the silicon insert seems to be more rigid than normal silicon inserts
I have a surface and uag. Had the surface first and like the feel but it doesn't really offer much protection. I saw the write-up on the uag and gave it a try. My surface stays on the ready but I haven't used it since receiving the uag.
Sent from my M7 using Tapatalk 4 Beta
Testingchip said:
I have a surface and uag. Had the surface first and like the feel but it doesn't really offer much protection. I saw the write-up on the uag and gave it a try. My surface stays on the ready but I haven't used it since receiving the uag.
Sent from my M7 using Tapatalk 4 Beta
Click to expand...
Click to collapse
Thanks for all the suggestions guys!
My incipio dualpro finally came in and I have to say I'm pleasantly surprised. I had my doubts after ordering that it would be too bulky or the silicon insert would be too flimsy.
I'm pleased to say that this case exceeded my expectations. There is some bulk added, however it isnt bad. It gives the phone some heft and just feels a little more solid. Fitment is perfect.
The only negative so far is that the volume rocker is a little harder to press
Yesterday I recieved the SPECK Presidio Grip for my new Google Pixel 2 XL. I thought that you might enjoy some photos and a short review. This review is neither sponsored, nor did I recieve any discount in order to write this review.
Pricing
SPECK lists this product for 44.95 USD. I paid ~10 USDs at an German online retailer who lists the case for ~25 USD and applying an available-to-all discount for new customers. The list price is pretty hefty, the reduced one is a steal.
Retail box
This case comes in the standard SPECK retail box which allows to take a sneak peak at the case without unboxing.
Build quality / Durability / Looks
Unlike the classic glossy CandyShell cases, the Presidio Grip is made of matted plastic with rubber stripes on. This looks nice and makes the phone much more easy to hold. The rubber removes the slippery quality of the phone's material.
This case has a two-layered construction: The outer layer is sturdy plastic while the inner one is soft rubber. The edges and corners have some air-cushion. SPECK promises that the case would resist scratches easily. Since it is only a day old, I cannot tell. But judged by the feel of the product, I tend to believe the promise.
The lid above the USB port is rubber only (without a plastic housing). I believe this to be a weakness as I experienced deformed/broken rubber at the exact same place earlier on other cases. Time will tell.
The lid in combination with the curved glass panel leads to deep ridges which are predestinated to collect lint. It might be necessairy to remove this cases from times to times in order to clean it.
Be aware that this case adds some bulk definitely more than rubber cases. And as the edges are air-cushioned, the device grows in dimensions to a point where a person with smaller hands might have trouble to hold it in a comfortable manner.
Protection
I am quite confident with the protection level: The sturdy outer shell combined with the air cushioned edges and the inner rubber layer might protect the phone from serious drips. The frontside lip is thick enough to protect the screen while dropping on almost flat surfaces and avoids scratches when putting the phone face to the table.
Fitting / Cutouts / Buttons
This case fits like a glove.. All needed cutouts are there. They are located perfectly and are surrounded by rubber to keep lint out of the case.
The buttons are rubber-made and are easy to press. The covered buttons still provide great tactile feedback.
Active Edge
Active Edge is still working with this case put on and not much pressure is needed to activate it.
Verdict
I highly recommend this case: It looks and feels great, provides great protection without adding too much bulk.
Please rate
Enjoyed this review? Do not forget to push the "thx" button!
Have it. Great case must own for my devices.
ademmer said:
Yesterday I recieved the SPECK Presidio Grip for my new Google Pixel 2 XL. I thought that you might enjoy some photos and a short review. This review is neither sponsored, nor did I recieve any discount in order to write this review.
Pricing
SPECK lists this product for 44.95 USD. I paid ~10 USDs at an German online retailer who lists the case for ~25 USD and applying an available-to-all discount for new customers. The list price is pretty hefty, the reduced one is a steal.
Retail box
This case comes in the standard SPECK retail box which allows to take a sneak peak at the case without unboxing.
Build quality / Durability / Looks
Unlike the classic glossy CandyShell cases, the Presidio Grip is made of matted plastic with rubber stripes on. This looks nice and makes the phone much more easy to hold. The rubber removes the slippery quality of the phone's material.
This case has a two-layered construction: The outer layer is sturdy plastic while the inner one is soft rubber. The edges and corners have some air-cushion. SPECK promises that the case would resist scratches easily. Since it is only a day old, I cannot tell. But judged by the feel of the product, I tend to believe the promise.
The lid above the USB port is rubber only (without a plastic housing). I believe this to be a weakness as I experienced deformed/broken rubber at the exact same place earlier on other cases. Time will tell.
The lid in combination with the curved glass panel leads to deep ridges which are predestinated to collect lint. It might be necessairy to remove this cases from times to times in order to clean it.
Be aware that this case adds some bulk definitely more than rubber cases. And as the edges are air-cushioned, the device grows in dimensions to a point where a person with smaller hands might have trouble to hold it in a comfortable manner.
Protection
I am quite confident with the protection level: The sturdy outer shell combined with the air cushioned edges and the inner rubber layer might protect the phone from serious drips. The frontside lip is thick enough to protect the screen while dropping on almost flat surfaces and avoids scratches when putting the phone face to the table.
Fitting / Cutouts / Buttons
This case fits like a glove.. All needed cutouts are there. They are located perfectly and are surrounded by rubber to keep lint out of the case.
The buttons are rubber-made and are easy to press. The covered buttons still provide great tactile feedback.
Active Edge
Active Edge is still working with this case put on and not much pressure is needed to activate it.
Verdict
I highly recommend this case: It looks and feels great, provides great protection without adding too much bulk.
Please rate
Enjoyed this review? Do not forget to push the "thx" button!
Click to expand...
Click to collapse
Thanks for the review. I had this case for the original Pixel XL and noticed the fit became more loose in a pretty short amount of time (like 4 days). I ended up going through 3 of these before I ended up with a Tech21 case instead which has retained its tight, glove like fit for at least 6 months now. Have you noticed this case becomes noticeably more loose over time?
Today was my 5th day of use. I removed and put the case back on several over the last few days. Until now, I haven't noticed any signs of a loosening fit.
Does it play well with tempered screen protectors?
Sent from my Pixel 2 XL using XDA-Developers Legacy app
Don_Perrignon said:
Does it play well with tempered screen protectors?
Click to expand...
Click to collapse
I don't have one but according from the look of it and the available space I'd say yes.
I have the Speck Presidio Show - which is the same case but with a clear back and without the grippy texture there. I love this case. It has a nice beefy front lip more so than the other three cases I have. Definitely not a slim case, but it's not overly thick either. Provides more serious drop protection than most cases as well, without being big like an Otterbox Defender.
pixelsquish said:
I have the Speck Presidio Show - which is the same case but with a clear back and without the grippy texture there. I love this case. It has a nice beefy front lip more so than the other three cases I have. Definitely not a slim case, but it's not overly thick either. Provides more serious drop protection than most cases as well, without being big like an Otterbox Defender.
Click to expand...
Click to collapse
Also have the Speck Presidio on my XL2. Love the case. I'm bad with dropping and this was by far the least slick case. No drops yet. I'm wanting to get a tempured glass to go with but can't decide after tons of readings seems like they are mostly all bad minus maybe the Dome whitestone. Which I'm not sure if it fits with this case and I'll be highly annoyed if I spend 45 and it doesn't. Although from looking at the edges I'd guess it would fit.
Don_Perrignon said:
Does it play well with tempered screen protectors?
Sent from my Pixel 2 XL using XDA-Developers Legacy app
Click to expand...
Click to collapse
I've had the Presidio Grip on my Pixel 2 XL since I got it in November (week of Black Friday). I agree with the reviewer -- fits very well, excellent grip and it certainly appears to offer excellent shock protection -- but it DOES make the phone significantly bulkier.
Re: the question about screen protectors: I have an InvisShield from SG Fresh Idea on the phone, and the Presidio Grip is perfect with that. There's only a tiny bit of clearance between the InvisShield and the Presidio grip, but it's enough so that the case never touches the protector, and therefore doesn't lift the protector at all -- even when I squeeze the side to trigger Google Assistant.
Since it fits the InvisShield perfectly, you can also be confident that it would be fine with the Whitestone Dome Glass, since that's a bit smaller than the InvisShield.
What's the name of the retailer?
ademmer said:
Yesterday I recieved the SPECK Presidio Grip for my new Google Pixel 2 XL. I thought that you might enjoy some photos and a short review. This review is neither sponsored, nor did I recieve any discount in order to write this review.
Pricing
SPECK lists this product for 44.95 USD. I paid ~10 USDs at an German online retailer who lists the case for ~25 USD and applying an available-to-all discount for new customers. The list price is pretty hefty, the reduced one is a steal.
Retail box
This case comes in the standard SPECK retail box which allows to take a sneak peak at the case without unboxing.
Build quality / Durability / Looks
Unlike the classic glossy CandyShell cases, the Presidio Grip is made of matted plastic with rubber stripes on. This looks nice and makes the phone much more easy to hold. The rubber removes the slippery quality of the phone's material.
This case has a two-layered construction: The outer layer is sturdy plastic while the inner one is soft rubber. The edges and corners have some air-cushion. SPECK promises that the case would resist scratches easily. Since it is only a day old, I cannot tell. But judged by the feel of the product, I tend to believe the promise.
The lid above the USB port is rubber only (without a plastic housing). I believe this to be a weakness as I experienced deformed/broken rubber at the exact same place earlier on other cases. Time will tell.
The lid in combination with the curved glass panel leads to deep ridges which are predestinated to collect lint. It might be necessairy to remove this cases from times to times in order to clean it.
Be aware that this case adds some bulk definitely more than rubber cases. And as the edges are air-cushioned, the device grows in dimensions to a point where a person with smaller hands might have trouble to hold it in a comfortable manner.
Protection
I am quite confident with the protection level: The sturdy outer shell combined with the air cushioned edges and the inner rubber layer might protect the phone from serious drips. The frontside lip is thick enough to protect the screen while dropping on almost flat surfaces and avoids scratches when putting the phone face to the table.
Fitting / Cutouts / Buttons
This case fits like a glove.. All needed cutouts are there. They are located perfectly and are surrounded by rubber to keep lint out of the case.
The buttons are rubber-made and are easy to press. The covered buttons still provide great tactile feedback.
Active Edge
Active Edge is still working with this case put on and not much pressure is needed to activate it.
Verdict
I highly recommend this case: It looks and feels great, provides great protection without adding too much bulk.
Please rate
Enjoyed this review? Do not forget to push the "thx" button!
Click to expand...
Click to collapse
what's the name of the German retailer? I'm in the UK so no customs fees...thanks
I had this case as well. I returned it, though, because the grip texture started to peel after a few weeks.
edgeicator said:
I had this case as well. I returned it, though, because the grip texture started to peel after a few weeks.
Click to expand...
Click to collapse
Wow...that's unusual for a Speck case. The Candy Grip has been around for several years, and the Presidio Grip is a similar concept, and they've been incredibly popular case for iPhones and many Android phones for years. I've had a Presidio Grip on my Pixel 2 XL since Thanksgiving -- just about 3 months now -- and use my phone a LOT, so the case is getting handled many times a day, sits in my pocket when not in use (except when on my nightstand charging at night), gets pulled in and out of my pocket dozens of times a day, etc., and -- it's indistinguishable from new.
Most people I know who have had Speck cases over the past 5 years or so have never had issues. I've read a tiny handful of reports online of folks who talk about peeling -- in most of these, it seems they bought online from a reseller, and it's been suggested that these were likely counterfeit Speck cases (apparently pretty common), sold as the real thing. Of course it's possible you have the real thing and it's peeling -- just a pretty rare occurrence -- I'm not challenging your experience -- just wondering if it's possible you had a counterfeit, or if Speck's quality control let a bad batch through. Where did you buy yours?
Same here, no issues with Speck cases! Best protection and grips!!
jonstrong said:
Wow...that's unusual for a Speck case. The Candy Grip has been around for several years, and the Presidio Grip is a similar concept, and they've been incredibly popular case for iPhones and many Android phones for years. I've had a Presidio Grip on my Pixel 2 XL since Thanksgiving -- just about 3 months now -- and use my phone a LOT, so the case is getting handled many times a day, sits in my pocket when not in use (except when on my nightstand charging at night), gets pulled in and out of my pocket dozens of times a day, etc., and -- it's indistinguishable from new.
Most people I know who have had Speck cases over the past 5 years or so have never had issues. I've read a tiny handful of reports online of folks who talk about peeling -- in most of these, it seems they bought online from a reseller, and it's been suggested that these were likely counterfeit Speck cases (apparently pretty common), sold as the real thing. Of course it's possible you have the real thing and it's peeling -- just a pretty rare occurrence -- I'm not challenging your experience -- just wondering if it's possible you had a counterfeit, or if Speck's quality control let a bad batch through. Where did you buy yours?
Click to expand...
Click to collapse
I bought mine from target.com when it was on sale during the holidays. 3 of the smaller, outer strips at the midline of the phone horizontally were peeling for me.
paulbadassbriant said:
what's the name of the German retailer? I'm in the UK so no customs fees...thanks
Click to expand...
Click to collapse
https://www.otto.de/p/speck-hardcas.../?variationId=649310242#variationId=649310242
17 EUR voucher + free delivery for new customers: https://www.otto.de/user/register?entryPoint=loginPage
Makes this case a steak!
edgeicator said:
I had this case as well. I returned it, though, because the grip texture started to peel after a few weeks.
Click to expand...
Click to collapse
Mine's still good as new.