Hey guys,
I broke my screen and cant use my Oneplus One anymore and I know there are many screen out there for Cheap and and are bad qualty. I have no good
experience with that.
Does someone know and used Screen with display or know where to get an good display for my oneplus one?
Greeting
PrinceOfDarkness said:
Hey guys,
I broke my screen and cant use my Oneplus One anymore and I know there are many screen out there for Cheap and and are bad qualty. I have no good
experience with that.
Does someone know and used Screen with display or know where to get an good display for my oneplus one?
Greeting
Click to expand...
Click to collapse
Hi, I bought 3 different OPO screen replacements at Aliexpress. As you said, the quality is so different. The first one was simply very pale and dark, the second one is the screen itself is OK, but touch screen and cable was so fragile. Te last one is completely fine. This is not the original, but if you just use it, you don't see the difference.
https://www.aliexpress.com/item/One...l-With-Frame-Replacement-For/32449686228.html
They offer the screen with and without the frame. ( Some said with the frame is easier for the beginner) I myself bought a screen without the frame. then you may need a double side tape (2mm) like below.
https://www.aliexpress.com/item/One...l-With-Frame-Replacement-For/32449686228.html
There are many instructions at youtube. But I used the below.
https://www.youtube.com/watch?v=uCka8Eg_Vqo
https://www.youtube.com/watch?v=vRQW666skQQ
Good Luck
PrinceOfDarkness said:
Hey guys,
I broke my screen and cant use my Oneplus One anymore and I know there are many screen out there for Cheap and and are bad qualty. I have no good
experience with that.
Does someone know and used Screen with display or know where to get an good display for my oneplus one?
Greeting
Click to expand...
Click to collapse
You may have already replaced yours, but as other poster said, quality is a crap shot sometimes.
First one I bought from Amazon. Great packaging and looked great, but frame was 1mm to wide, so volume buttons were permanently depressed (so each reboot went to recovery). Returned that one.
Bought another from eBay here, frame is PERFECT size. Screen has a slightly blue hue, but not noticeable really. No tools come with this one, so you need a pry tool and screw drivers.
Word of caution, the internal antenna can break very easily if you are not VERY careful when disassembling. Additional antennas are here. I recommend getting a couple.
Hi! I need a replacement screen as well, because a stripe in the middle of mine stopped working.
After tons of research on Aliexpress i don't know which one to decide between these 2:
1) https://it.aliexpress.com/item/Orig...ml?spm=a2g0o.cart.99999999.259.30453c00U4QgqW
This one costs almost twice the others, but i contacted the seller and he said it's an original one (don't know how much i can trust him).
2) https://it.aliexpress.com/item/Tras...ml?spm=a2g0o.cart.99999999.259.30453c008Kl1tr
This one has same price as most of the other screens and has lots of good reviews, but i know it must be a clone.
Hi, I bought 3 different OPO screen replacements at Aliexpress. As you said, the quality is so different. The first one was simply very pale and dark, the second one is the screen itself is OK, but touch screen and cable was so fragile. Te last one is completely fine. This is not the original, but if you just use it, you don't see the difference.
https://www.aliexpress.com/item/Onep...449686228.html
Click to expand...
Click to collapse
I also looked into this one but i saw several reviews about dead pixels so i discarded it.
Anyone who bought any screen, share your experience please!!!
restartoshi said:
Hi, I bought 3 different OPO screen replacements at Aliexpress. As you said, the quality is so different. The first one was simply very pale and dark, the second one is the screen itself is OK, but touch screen and cable was so fragile. Te last one is completely fine. This is not the original, but if you just use it, you don't see the difference.
https://www.aliexpress.com/item/One...l-With-Frame-Replacement-For/32449686228.html
They offer the screen with and without the frame. ( Some said with the frame is easier for the beginner) I myself bought a screen without the frame. then you may need a double side tape (2mm) like below.
https://www.aliexpress.com/item/One...l-With-Frame-Replacement-For/32449686228.html
There are many instructions at youtube. But I used the below.
https://www.youtube.com/watch?v=uCka8Eg_Vqo
https://www.youtube.com/watch?v=vRQW666skQQ
Good Luck
Click to expand...
Click to collapse
I have attached screen samples. OPO original, low quality and good quality replacement from Aliexpress. I don't think that you will get the origianl OEM screen replacement from Aliexpress.
It seems that Replacebase (UK supplier) sells the OEM (original) screen replacement for OPO. I haven't tested this screen, but their OPO red battery is really great. (See XDA forum discussion)
https://www.replacebase.co.uk/oneplus-one-replacement-lcd-touch-screen-assembly-black-original/
Related
Hello everyone.
The LCD of my S3 was broken so I ordered a replacement screen on eBay.
It arrived and I replaced it without incident. (It was an LCD + Frame + digitizer assembly)
But after a couple hours I noticed that the LCD is a couple of millimeters smaller on each side.
It is really not noticeable on first sight. The first days I dismissed it because it was something that didn't bug me too much.
But I noticed that I keep mistyping when I'm using the keyboard. Also I keep missing other onscreen buttons and it drives me insane!
I think this is because the digitizer is made for a larger LCD.
First I thought that it was a software problem, but you can see the borders even when the display is off.
I tried taking a picture and you can definitely see it on the left and the bottom border.
http://i.imgur.com/qvkZFFM.jpg
http://i.imgur.com/PgR6gDd.jpg (I turned the brightness to the max here so you could see the borders.)
Should I ask for an RMA? Or am I seeing ghosts here??
Love to hear your thoughts.
That s not an SAMSUNG OEM LCD Display.. Look at capacitive buttons color...
Sent from my GT-I9300 using XDA Free mobile app
If you look at the spacing the Samsung logo at both the top and bottom, there is an extra bit of space and as you rightly said, the bezels on the sides are a bit thicker. If it gives you peace of mind, then go for the RMA, but chances are you might end up getting the same thing. Maybe you could try a different seller? Where did you purchase it from?
RazOne said:
That s not an SAMSUNG OEM LCD Display.. Look at capacitive buttons color...
Click to expand...
Click to collapse
Yeah probably not
The capacitive buttons are the normal white color. In the picture they are not on.
Xander_25 said:
If you look at the spacing the Samsung logo at both the top and bottom, there is an extra bit of space and as you rightly said, the bezels on the sides are a bit thicker. If it gives you peace of mind, then go for the RMA, but chances are you might end up getting the same thing. Maybe you could try a different seller? Where did you purchase it from?
Click to expand...
Click to collapse
This is the one I bought:
http://www.benl.ebay.be/itm/251511330397?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
Is there a seller you recommend?
I guess I'm just going to keep using it and wait for the next gen smartphones.
Thanks for the info!
Touch function Not working
Hi,
I am using Galaxy S3 Korean Version (SHV-E210L).
I have tried TraingleAway V2.35 to reset flash counter. But it did not reset flash counter, but damaged touch function. Now my phone display is working, but touch function is not working. I am using OTG cable with Mouse for urgent works.
I have two things which i need answer. Can some one help me.. ::crying:
1. Before i fix this, i need to reset flash counter anyway. But latest versions of TraingleAway are not working for this model and Previous versions from V2.35 is also give massge stating "Are you not using ICS". Phone has Android 4.3. So can some one give me a solution?
2. I want to fix touch problem and i search for digitizer in Ebay. But there are digitizers for GT-I9300, but not for SHV-E210L? Is digitizer for 9300is compatible for SHV-E210L? Further waht is screen lens means? Is it digitizer?
Thanks a lot
conspiracyBE said:
Hello everyone.
The LCD of my S3 was broken so I ordered a replacement screen on eBay.
........
Should I ask for an RMA? Or am I seeing ghosts here??
Love to hear your thoughts.
Click to expand...
Click to collapse
Hi, that's about the price I paid for supposedly genuine (but not) screens on ebay for my S3, my buttons are also not white as mentioned above.
The first screen I fitted went faulty after about an hour, took a while to get a refund, I had to pay postage back.
Second screen cracked after a very small drop, digitiser was OK, bought replacement screen but when changing it (with heat, etc) the digitiser separated from its backing rather than the screen.... maybe me being ham fisted but I think it was a different bonding used
Third screen/digitiser assembly now has a crack running right across it, and I've not ever dropped it! It still works so I'm leaving it alone and buying a new phone this time.
Also I find the paint comes off the frame very easily by taking it out of a hard case or screen mount and mine looks a mess after a couple of months, and the frame joint is obvious and creaks when pressed.
So these screen aren't very good - but I couldn't find a definitely genuine screen for a price that was worth bothering to fix the phone.... I would definitely get a tempered glass protector if I did fit another of these.....
So I accidently broke my screen and the touch stopped working. Thought I buy a new one off ebay but there are so many of them and half is probably copies. Does anyone know of a legit seller?
I wish I had the answer for you. I'm in the same boat so I hope someone knows of a good supplier that can provide a screen with good quality. I've looked at many that are available on Amazon and eBay and it appears none are GorillaGlass and tend to break easily.
Has anyone had good luck with a particular part?
xam247 said:
I wish I had the answer for you. I'm in the same boat so I hope someone knows of a good supplier that can provide a screen with good quality. I've looked at many that are available on Amazon and eBay and it appears none are GorillaGlass and tend to break easily.
Has anyone had good luck with a particular part?
Click to expand...
Click to collapse
I ordered this one (link below) a couple of weeks ago. I looked at a few and this was by far the best quality I found. It has Corning Gorilla Glass 3 and is oem compliant.
http://m.repairsuniverse.com/oneplus-one-lcd-touch-screen-assembly-with-frame-replacement.html
It's like $45 don't waste money on the FedEx for UPS shipping. With all the bad weather they take longer than the post office.
Another thing luckily they sent me but its like a dollar to get another one is the black double-sided adhesive because you're going to have to take this thing apart more than you expect.
Ifixit has a pretty good tutorial just make sure to read it completely so you don't break a cable end.
https://www.ifixit.com/Teardown/OnePlus+One+Teardown/26484
To the top left of the rear facing camera /top right of the ear speaker after you get the logic board out, pull out the little gray rubber square.
If you can, use a heat gun liberally. Don't try to half ass it and pry out the power button and volume button flex cables, you WILL break them! Learned that the hard way with the power button. In the event that you do, this was the store page for the power button flex I used: https://www.aliexpress.com/item/Hig...utton-Wire-Flex-Cable-Repair/32548508603.html
For installation, you won't find it online, but just use a soldering iron to melt solder off the broken flex cable, remove, and solder new flex cable.
Does this screen get close to the original brightness and color saturation?
I ordered one from ebay about 6 months ago and the screen brightness is about half, compared to my wife's undamaged oneplus one, and the colors seem pale.
hectorbls said:
Does this screen get close to the original brightness and color saturation?
I ordered one from ebay about 6 months ago and the screen brightness is about half, compared to my wife's undamaged oneplus one, and the colors seem pale.
Click to expand...
Click to collapse
I have two these phones so side by side with the stock display is it close to similar as you're going to get.
If you drop phones as much as I do, go for the tudia case. It's big bulky and feels like cheap plastic but it is probably saved my screen a dozen times this month, and their description is BS do put the thin tempered glass protector on it so it fits snug for touch
My P9 EVA-L19 Glass LCD Broken
Hi
Unfortunately, my P9 EVA-L19 fall down and its glass LCD broken .
I purchased a replacement and I hope it works as original one.
http://www.witrigs.com/oem-lcd-with-digitizer-for-huawei-p9-gold
Good to know...
Cool story.
I have received the LCD replacement and I also installed it by my self.
So far so good
but I compare the new LCD with my friend P9 and I found there is slight difference in color.
but it is good for me.
Good congratulations
I bought an replacement lcd assy from germany.. after cursing with the replacement (mostly with the battery) i powered up the phone and noticed that swiping home screens worked only 1 time in 10..
Checked with the debug tools that touch location works perfectly.. but touch point size shows always zero, and the actual touch point size is displayed in the pressure
Can anything be done with the means of software, or is this gonna be a bad ebay review?
Sigh. What is wrong with these people. TEST BEFORE INSTALL. So you can send it back to warranty without issues and not leave a bad eBay review for a defective screen.
..
yes you have to TEST BEFORE INSTALL
I recommend this replacent so far
I had my screen broken last night, how's the A+++ screen replacements quality compared to factory one (JDI)?, in terms of responsiveness, quality, deep blacks, brightness. color calibration, etc, I'm very upset and worried about this and the fact that I may end up with something not on par in terms of quality...
Bleak3993 said:
I had my screen broken last night, how's the A+++ screen replacements quality compared to factory one (JDI)?, in terms of responsiveness, quality, deep blacks, brightness. color calibration, etc, I'm very upset and worried about this and the fact that I may end up with something not on par in terms of quality...
Click to expand...
Click to collapse
I recommend the lcd screen I purchased see my post:good:
OEM LCD with Digitizer for Huawei P9 Gold
SKU: 112326
Be the first to review this product
Availability: In stock
US$25.00
Price Drop Alert
https://www.witrigs.com/oem-lcd-with-digitizer-for-huawei-p9-gold#customer-reviews
akeshma said:
OEM LCD with Digitizer for Huawei P9 Gold
SKU: 112326
Be the first to review this product
Availability: In stock
US$25.00
Price Drop Alert
https://www.witrigs.com/oem-lcd-with-digitizer-for-huawei-p9-gold#customer-reviews
Click to expand...
Click to collapse
I bought the LCD the OEM here, work and looks great. Don't know how to tell if it's OEM but everything seems as good as original. I also compared with other P9 and couldn't tell that mine was replaced.
I also bought a OEM battery to fix the suddenly shutting down problem at less than 50% charge, mainly when using camera. Seems fixed.
Buran79 said:
I bought the LCD the OEM here, work and looks great. Don't know how to tell if it's OEM but everything seems as good as original. I also compared with other P9 and couldn't tell that mine was replaced.
I also bought a OEM battery to fix the suddenly shutting down problem at less than 50% charge, mainly when using camera. Seems fixed.
Click to expand...
Click to collapse
from where you bought the battery ?
akeshma said:
from where you bought the battery ?
Click to expand...
Click to collapse
Battery
https://www.aliexpress.com/item/Ori...i-Ascend-P9-Lite-G9-VNS-DL00/32815982023.html
Hopefully one of you can help me
I currently have two huawei p9, wife's and sister in-laws, my wife is on her second screen already and needs to be replaced again.
The screens I found, cheap ones on eBay (lltrader I think) they don't look too bad at all.
First screen I replaced on my wife's was awful and the glue melted and the glass seperate and cracked within a week.
The second was from the seller I mentioned above, but she is a clumbsy woman.
So for this third one I am looking for for a glass screen protector, the problem is the replacement screens don't have the curved edges. So all the screen protectors for the position are too small or are designed to fit the curved edges...
Do any of you know a phone with very similar dimensions that I could try a screen protector from. I am sick of replacing screens now...
My phone whyred has always been in a case/screen protector since new
A couple of days ago my 4 yr old threw my phone violently and has smashed the screen :crying:
I can see on Aliexpress there are replacement screens for sale: https://www.aliexpress.com/item/For...09-47d6-b983-9f29fe68067d&transAbTest=ae803_4
I am based in the UK and this phone is not as popular as in India etc and there are not many places to get screen replaced
I have watched a few videos online, can this be done without all of the fancy machines?
For example do you really need a press? could you not just stick a heavyish book on the phone or is it just not possible
Clutching at straws I know
No, it doesn't work like that... if u want to replace just the glass.. you must have a UV lank to dry the glue..
I think he has to change the complete screen .
Did you look to the tuto on youtube ?
Just buy a new display and replace it. It is much easier but it costs a bit more. Make sure it comes with the frame as well.
The Restless Soul said:
Just buy a new display and replace it. It is much easier but it costs a bit more. Make sure it comes with the frame as well.
Click to expand...
Click to collapse
I can see the complete display on Aliexpress
I replaced the display on my Redmi Note 3 pro and it was never the same again
The replacement displays are not a patch on the original
I may have to go down that road, is there no one who has attempted to replace the glass themselves?
gap30 said:
I can see the complete display on Aliexpress
I replaced the display on my Redmi Note 3 pro and it was never the same again
The replacement displays are not a patch on the original
I may have to go down that road, is there no one who has attempted to replace the glass themselves?
Click to expand...
Click to collapse
It is very hard to do a glass-only repair. You have a 60-70% chance to break the display during the process
Broke my display, digitalizer and screen still intact only glass shattered.
As I live in Brasil, there is no trustworthy shop to replace screen.
Searching at aliexpress I saw lots of people complaining that screens are subpar to original.
Can someone recomment a place where I can buy an original replacement, or at least a good one?
My phone screen is "tianma td4310".
Hi all. I've had un unfortunate phone drop last night, resulting in the glass of the screen broken in the lower left corner. The screen is displaying perfect and so the digitizer. I've seen some sellers on amazon selling the glass only with no digitizer nor display. Can anyone let me know if this can be changed (glass of the screen only), and if so, any tutorials or videos to do so?
I really dont want to spend more than $100 on a new screen...
I hope someone helps! Thanks!!! Cheers.
FedericoUY said:
Hi all. I've had un unfortunate phone drop last night, resulting in the glass of the screen broken in the lower left corner. The screen is displaying perfect and so the digitizer. I've seen some sellers on amazon selling the glass only with no digitizer nor display. Can anyone let me know if this can be changed (glass of the screen only), and if so, any tutorials or videos to do so?
I really dont want to spend more than $100 on a new screen...
I hope someone helps! Thanks!!! Cheers.
Click to expand...
Click to collapse
I dropped my Pixel 2 XL in November, also only the glass was broken.
But I paid €180 for the glass plus screen, because the screen is razor-thin and glued to the glass. As far as I know, the glass isn't sold separately, at least not as original from Google.
And believe me, the glass is very thin, but the screen is even thinner. So before buying a third-party-glass, I would check how to get the screen off the glass and back again.
I've been looking for some videos about this, and it looks really complicated to separate the glass from the screen, but possible. Some guys apply extreme cold or heat to unglue the screen, then they clean up ALL the screen, and then they reapply something to stick it to the new glass (I don't know what they use). So balancing the hard work to do this, I'm starting to think it will be a better option to change the whole screen. Do anyone knows if new purchased genuine screens comes with the blue problem solved? Any good place to purchase a genuine one within USA?
Thanks for the answers and help...
FedericoUY said:
Do anyone knows if new purchased genuine screens comes with the blue problem solved? Any good place to purchase a genuine one within USA?
Click to expand...
Click to collapse
Anyone?
Please any suggestions on where to buy a good screen for this phone?
FedericoUY said:
Please any suggestions on where to buy a good screen for this phone?
Click to expand...
Click to collapse
https://www.ifixit.com/Store/Android/Google-Pixel-2-XL-Screen-and-Digitizer/IF356-025?o=1
https://www.repairpartsplus.com/Goo...-QU6eVr7pcz-dSfc7zGXfxrjMZ_L0QHQaAsMHEALw_wcB
HueyT said:
https://www.ifixit.com/Store/Android/Google-Pixel-2-XL-Screen-and-Digitizer/IF356-025?o=1
https://www.repairpartsplus.com/Goo...-QU6eVr7pcz-dSfc7zGXfxrjMZ_L0QHQaAsMHEALw_wcB
Click to expand...
Click to collapse
Thank you no stock on the first one, but looks like the second has to sell...