How can I escape from 9008 mode? ( ZUK Z2 ) - Lenovo ZUK Z2 (Plus) Questions & Answers

The day before yesterday,
My phone became bricked caused by any reason.
I cound download ROM by using Mi-flash or QFIL but nothing happened after successing ROM download.
When I pushed Power key more than 5sec ~ 30sec, it did not blink led nor vibrate, keep black screen,
And PC lost connection and recover it as "9008" again.
PC could always
detect my phone as "Qualcomm HS-USB QDLoader 9008".
How can I recover my phone?
Please help me escape from nightmare.

Josephjin said:
The day before yesterday,
My phone became bricked caused by any reason.
I cound download ROM by using Mi-flash or QFIL but nothing happened after successing ROM download.
When I pushed Power key more than 5sec ~ 30sec, it did not blink led nor vibrate, keep black screen,
And PC lost connection and recover it as "9008" again.
PC could always
detect my phone as "Qualcomm HS-USB QDLoader 9008".
How can I recover my phone?
Please help me escape from nightmare.
Click to expand...
Click to collapse
Flash again with qfil.

Palash9088 said:
Flash again with qfil.
Click to expand...
Click to collapse
I did more than 10times but the result was same.
Thanks,

Josephjin said:
I did more than 10times but the result was same.
Thanks,
Click to expand...
Click to collapse
u need to do unbrick using the deep flashing cable..
These links should help you.
https://forum.xda-developers.com/lenovo-zuk-z2/help/hard-bricked-trying-to-restore-twrp-t3747602
https://zukfans.eu/community/thread...-from-hard-brick-state-9008-mode-easily.3504/

Related

lenovo P1 totally bricked

I was trying to use QFIL to update the phone and get rid of chinese characters,and now my phone is completely blank with no sounds or vibration.The computer still connects to the phone in QFIL but doesnt show as a device on the computer.
Any help in fairly simple language would be great.
alan53 said:
I was trying to use QFIL to update the phone and get rid of chinese characters,and now my phone is completely blank with no sounds or vibration.The computer still connects to the phone in QFIL but doesnt show as a device on the computer.
Any help in fairly simple language would be great.
Click to expand...
Click to collapse
Go to stock recovery if it is possible( both volume + power button) then power off and then press volume up anx cpnnect to pc. What happened now?
Thanks i tried stock recovery nothing happens ie no reaction from the phone,if i hold the power button for a minute and then press volume up and connect to pc the pc bleeps
Does Qualcomm port shows?
Can you use qfil program in this state?
yes qualcomm shows in device manager and qfil seems to work but ends in sahara fail
alan53 said:
yes qualcomm shows in device manager and qfil seems to work but ends in sahara fail
Click to expand...
Click to collapse
qualcomm 9008 or 9006?
Starchm said:
qualcomm 9008 or 9006?
Click to expand...
Click to collapse
qualcomm 9008
got it fixed somehow!

Phone bricked?

Hi, I was wondering if anyone has encountered this problem? The phone has been updated to the latest firmware as of the 8th of October 2017. I was using the facebook app and it was crashing repeatedly; after a few times of attempting to restart the app and crashing, the phone froze (black screen) and I tried to do a soft reset (30 secs on power button) but to no avail. I noticed that when the phone is put on the charger, the white LED flash for the front facing camera started blinking. I tried plugging it into the laptop and noticed that "Qualcomm HS-USB QDLoader 9008" driver is installed. Of course white LED flash was blinking too. A bit of digging seems to suggest that the bootloader has been corrupted. How is this possible and how can it be fixed (stopping short of contacting motorola)? Thank you for any advice in advance.
Flash stock firmware !?
Unfortunately I can't even get into the recovery mode (aka down + power button as per instructions here - https://motorola-global-en-aus.cust...ail/a_id/113698/p/30,6720,9837/kw/clear cache). Any other ideas?
Try this: https://forum.xda-developers.com/showpost.php?p=72813119&postcount=6
Oh no, black screen hard brick (to my face)
MP1_ said:
Try this: https://forum.xda-developers.com/showpost.php?p=72813119&postcount=6
Click to expand...
Click to collapse
I have the same issue. Z2 NASH is booting and showing the qualcomm usb qloader in windows however I have no response from the gui or screen whatsoever. This happened immediately after a factory reset so, not only can I not boot to TWRP, but I also cannot communicate thru ADB. Please help if you can. I am currently following your guide here for flashing from windows and installing / flashing stock firmwares. I will post back my results. Thanks for any help you can offer...
I have the same issue, have there been any fixes? My Moto z2 play randomly bricked one night, same "Qualcomm HS-USB QDLoader 9008" in my "other devices" tab, and i have no clue what to do. My phone wont do a single thing, it was flashing the led on the right side when it was charging, now it does nothing at all. Any help is appreciated

How could I fix specified recourses or device not available error on mi flash tool?

Whenever I put the battery on my redmi 1S MI logo keep restarting in every 2 seconds and and the fastboot mode also do this . After that I tried that test point method.and after that I discovered that my battery died and it is not charging then after some days I bought a new battery and while continuing the process I got the error "specified resources or device is not available" in 18 seconds of process in mi flash tool. when the qualcomm hs-usb loader 9008 port convert into Qualcomm hs usb 9006. Now my device is stuck in EDL mode no display black screen no response on and volume up down power button and when I connect the phone to PC it detects as the Qualcomm HS USB 9008 port.and when I connect the phone to the charger of PC without battery the red LED Notification light just blinks one time. Now please help me I got one and only the phone. And now I can't buy a new phone please suggest me away to get out of this problem. What do you think my phone hard bricked???.
:crying:
parag2001 said:
Whenever I put the battery on my redmi 1S MI logo keep restarting in every 2 seconds and and the fastboot mode also do this . After that I tried that test point method.and after that I discovered that my battery died and it is not charging then after some days I bought a new battery and while continuing the process I got the error "specified resources or device is not available" in 18 seconds of process in mi flash tool. when the qualcomm hs-usb loader 9008 port convert into Qualcomm hs usb 9006. Now my device is stuck in EDL mode no display black screen no response on and volume up down power button and when I
connect the phone to PC it detects as the Qualcomm HS USB 9008 port.and when I connect the phone to the charger of PC without battery the red LED Notification light just blinks one time. Now please help me I got one and only the phone. And now I can't buy a new phone please suggest me away to get out of this problem. What do you think my phone hard bricked???.
:crying:
Click to expand...
Click to collapse
Hi @parag2001
Follow the steps its a similar problem like yours
Link
https://forum.xda-developers.com/redmi-1s/help/redmi-1s-bricked-t3788482
Hope it helps
Alan Jose said:
Hi @parag2001
Follow the steps its a similar problem like yours
Link
https://forum.xda-developers.com/redmi-1s/help/redmi-1s-bricked-t3788482
Hope it helps
Click to expand...
Click to collapse
I tried each and every version of Mi Flash tool but not the first one. On each versions the Qualcomm HS USB qdloader 9008 changed to 9006 but after 4or 5 seconds the loader reverts back to 9008 and the error happens.
Will try the first version of mi flash tool. Thanks.....
parag2001 said:
I tried each and every version of Mi Flash tool but not the first one. On each versions the Qualcomm HS USB qdloader 9008 changed to 9006 but after 4or 5 seconds the loader reverts back to 9008 and the error happens.
Will try the first version of mi flash tool. Thanks.....
Click to expand...
Click to collapse
Did u fixed it??
Alan Jose said:
Did u fixed it??
Click to expand...
Click to collapse
Nope .. but I am trying.. iam think ing to follow this
https://www.google.co.in/amp/s/www....e-the-right-kind-of-rom-qhsusb_dload_edl/amp/
Can it fix my device???
Please suggest me a way..

Z2 plus dead completely

It was working fine till the failed OTA update.
After a failed OTA update the phone is dead completely.
Unable to boot, or to recovery or to bootloader etc
Attempted QFIL and even that is not working.
A tiny white light is on but nothing else.
Did anyone recover the phone from this problem?
Or is the phone gone forever?
try to disconnect the battery, then plug again and try qfil
Hi, Can you try pressing Power button for long till the phone vibrates
Keep the Power button pressed down for a good 30-40 seconds or until u feel a little vibration.
arielcasari said:
try to disconnect the battery, then plug again and try qfil
Click to expand...
Click to collapse
QFIL recognises the phone as Qualcom HS-USB Diagnostics 900E (Com3).
Is this correct?
I downloaded this Lenovo_ZUK_Z2_Plus_Indian_Firmware_V2.5.104_ST_by_Annabathina file?
In Qfil, i chose flat build and then only the above folder is shown and its shows two files with .elf extension as below.
prog_emmc_firehose_8996_ddr & prog_emmc_firehose_8996_lite
Which one should i use? Howlong the process goes? I tried both and i don't see any changes even after 15 minutes?
Is there a guide available?
Any links if possible?
Thanks
Plenty of guides if you Google it. Your phone is NOT dead and can be recovered but you'll lose your data after a qfil. Zuk z2 is pretty much impossible to brick
This is simple to solve, make a deepflash cable to enter in edl mode.

Please Help ME

i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
absigma said:
i did a big mistake..i flashed redmi 6 pro rom to my a2 lite ..now nothing is happening...edl mode/fastboot mode is not accessing.i also show my phone to a service center. thaaaay just **** me they breaak my fingerprint reader.......help me to boot my phone i have to brought a back-part with finger print reader.please help me
Click to expand...
Click to collapse
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
In few words search in Google : test point mi a2 lite and do it
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
i cant access fastboot but it is connecting to edl mode but not getting flash.when its connect a sounds on pc but when not properly not in edl the notification light blinking.please help me.
Os_Herdz said:
In few words search in Google : test point mi a2 lite and do it
Click to expand...
Click to collapse
tnx bro but i know testpoint and i used that when my phones bootloader locked
SubwayChamp said:
Flash a proper stock rom, if you have a Mi A2 Lite phone through EDL mode this will revert a normal brick.
EDL mode is ever accesed, it might happen that device doesn´t start any kind of transfering data process through EDL, this means that your device is hard bricked in a way that motherboard can´t receive data so it´s damaged at hardware level but to prove this you have to first install the proper Qualcomm HS-USB qdloader 9008 drivers and see how is detected through device manager, it could be detected as Diagnostics 9006 with a warning symbol and then you have to update drivers, restart pc and re-start the process.
If then of bypass properly all the failures that XiaoMi flash tool can produce doesn´t work then the damaged was more serious.
If you unlocked previously (I guess you did it) then you can enter to EDL from a power off by holding both volume buttons at same time that you connect with pc -you have to first start the app and load the image- if device enters to EDL mode but the tool is not recognicing it the led light will stay on BUT if you entered correctly to EDL mode and also the tool is properly recognicing it (so the drivers were well updated) then the led light will flash intermitently.
At time to connect to pc in the mentioned steps you have not to receive any vibration just a sound from your pc.
Click to expand...
Click to collapse
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
absigma said:
now showing in mi flash as COM6 but when try to flash is says ''cannot read from COM6" help me
Click to expand...
Click to collapse
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Edit: Now I read your previous post, Led light has to blink, this is correctly connected, see under device manager how it is detected.
SubwayChamp said:
How is detected under device manager? qualcomm-HS-USB qdloader 9008? Also what about behaviour of led light, it stays on all the time or it blinks?
Click to expand...
Click to collapse
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
Ok, Behaviour changes depending on what rom you actually are, it´s mean that now you have flashed some partitions from Miui rom (led light will stay off) at least it´s being detected.
Things that you can try:
- Move the rom to the same folder where XiaoMi flash is.
- Rename the folder as short as better like "xiaomi" without quotes.
- Put your Windows in "Test Mode", restart to changes take effects.
- Switch to other version of the tool, it worked for me latest from here https://xiaomifirmware.com/downloads/miflashpro/
- Try with other rom version.
absigma said:
connected as qualcomm-HS-USB qdloader 9008 in device manager & the notification light is off when not in edl mode that time notification light blinks
Click to expand...
Click to collapse
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
absigma said:
i mconnect the battery now qualcomm-HS-USB qdloader 9008 in device manager & notification is blinking
Click to expand...
Click to collapse
Don't worry about led behaviour, your device will turn a bit weird cause you flashed a wrong firmware, the important here is that it's recognised by pc. What about the steps, tried?

Categories

Resources