i know what your thinking, not another bloody rsd lite wont recognise their defy. but hold on a second. i have literally tried everything. ive had to start using the macgyver hack cuz i drained the battery. im running rsd as an administrator, ive tried putting my phone in bootloader and as per the rsd user guide just with m logo showing. ive downloaded the driver software and reinstalled that. i have searched many threads and seen lots of people who's phone has been recovered but for some reason none of these seem to work for my phone. this all started with a basic slip of the finger. i had just installed miuiandroid on my phone and was going to make a backup, just in case. i know, ironic huh. i shut the phone down and went to reboot but held my finger on the vol up instead of down and got put thru to the bootloader. i pressed the power button to turn it off to start again but it just went blank. i pulled the battery and found myself stuck at the m logo. please can anyone help me save my defy.
Since your phone is not booting you have to reinstall the system using an SBF file. Hope you didn't flashed an 2.3 FULL SBF cause it's a bit harder to go back to Froyo (it's impossible to return via Froyo SBF flashing), but if you'll use the search function you'll find some threads with detailed steps to follow.
Now going back and assuming you didn't flashed a FULL Gingerbread SBF: from what you've wrote above I understand that the Defy is not recognized by RSD while your phone it's showing the M logo, which means you are not in bootloader mode. To enter into bootloader mode you have to turn off the phone and then hold down Vol Up + Power for few seconds then you can release them. Now on your screen you should see "Bootloader 09.xx – Battery OK – OK to Program – Connect USB data cable" which means you are in bootloader mode.
Before you connect the USB cable you must ensure you have installed the Motorola USB drivers on you computer. If you didn't did this part then do it now and after that you can plug the Defy and start RSD Lite (try to use a most recent version ... at least 4.9). If you previously installed the drivers you might wanna remove them, install CCleaner and do a cleanup then reboot your PC an reinstall the drivers to be sure this is not a driver issue.
In addition it's strongly recommended to do a full wipe from stock recovery (start phone using Vol Down + Power button) before flashing the SBF. If for various reasons you cannot access Custom Recovery then you can try to flash the Froyo SBF and after it will be fully flashed and your phone will reboot and will get stuck at the M logo you can try to enter the stock recovery and do a full wipe as it should work now. After this it should start, unless you've installed an 2.3 (leaked Gingerbread) FULL SBF and your phone won't start unless you'll flash the same SBF, because direct downgrade (by flashing a FULL SBF) it's not possible.
Soved
Works Perfectly. Thread must be marked as solved.
So, I've been seeing A LOT of threads regarding bricked devices (be it soft or hard bricks). So, I decided to create this thread, so everyone with bricked devices post here for help, instead of filling our forums and XDA servers with a load of topics with the same stuff.
If someone knows of a general unbricking thread, please PM me or tag me with a link so I can post on this post.
I will PM a mod to pin this thread to top.
To all brickers,
Before posting, try this thread:{RECOVER SOFT-brick}[2012 XPERIA's]Recover ALL 2012 XPERIAs from SOFT-brick
Remember to give the author thanks
Xperia S Return Back To Stock!
Pre-Requisites
For All The New Users..
If You Did Something Wrong
If nothing is working out
Not Able to Fix
Need to Return Back To Original Firmware?
Here is the Guide For You
Click to expand...
Click to collapse
Return Back To Stock
GUIDE for Better Understanding With Pictures And Images For New Users
Explained Step By Step
Click -- [HERE]
Just a tip: Try downloading Sony Update Service and following the instructions if you get a green LED blink on your phone, which is way simpler to recover without any problems.
Guys My ION LT28h got bricked during a recovery using CWM.
First It was a soft brick, i did something , random pressing of buttons made it worse. its on HARD BRICKED STATE now. Its been more than 5 weeks.
So after some research i found out that my Kernel is ****ed up. My phone is Boot loader Locked, so i cant flash the Kernel separately.
Now few of our fellow xda members told me to unplug the battery cable from the motherboard.
I have successfully disconnected the battery cable from motherboard, i kept it disconnected for one whole night.
Whats the next step ?
Will i be able to flash it with flash tool after connecting the battery to motherboard back ?
Will i be able flash the busted Kernel to a working stock kernel ?
Accidentally messed up and soft bricked Ion- LT28h.
xperia Ion LT28h
ROM: JB 4.1 Pure CyanogenMod Based on CM 10 FXP 218
kernel: GI Kernel v3 or v5
Recovery: TWRP and CWM
Rooted and Unlocked Bootloader
Hi guys, above mentioned were my previous settings. Had occassional reboots and sometimes it was kinda laggy that's why i decided to flash it to another ROM - supposedly to ParanoidAndroid. After following steps to install PA, my phone was on bootloops, was in a hurry then freaked out, i tried soft and hardreset, and tried booting on recovery both on twrp and cwm to flash properly as what was instructed however i may have flashed the wrong zips interchangeably with other roms and kernels resulting to a total messed up ion. i could have restored immediately to a saved CWM or TWRP backup right away however, i only stopped resetting when my phone suddenly stopped responding, no Sony logo, no Xperia logo, no boot, just backlight on, does not turn off, soft and hard reset no nothing. i guess until the battery went dead, then i charged it the whole night.
after reading most threads on recovering softbricked phone, mainly this {RECOVER SOFT-brick}[2012 XPERIA's]Recover ALL 2012 XPERIAs from SOFT-brick thread, and after a couple of days of red led, i constantly charged, i patiently waited(2days) still no green led, however i found out that i can access fastboot. (blue led).. i managed to get to this fastboot mode(blue led) ONLY after i soft reset or power+vol.up/1 vibrate the phone once the backlight lits up- on&off - for about less than a minute then it goes back to red led. (i'll be calling that stage as backlit-on&off-then-back-to-solid-red-led cycle) but then again if i go to fastboot, it will stay in fastboot mode during flashes and it stays there until the battery runs out and goes back to red led. then i charge my phone again, but
during fastboot mode, i have tried flashing the kernel, system and boot image. all via Fastboot command prompt.
and all were successful. there were combinations like, flashing only the kernel, tried flashing kernel and system, tried boot image only, tried all the same time, tried system only, tried different kernels, system and boot img, BUT STILL my phone wont even give me the sony logo screen.
then i thought i may need to wipe cache and userdata so i also erased cache and userdate a couple of times via fastboot mode command prompt. and yes fastboot does detects my phone. it can reboot to bootloader or just the normal fastboot reboot. so i have no issues regarding phone and pc via using fastboot command prompt. and Same thing - all flashes were successful,
i have flashed i think more or less than a total of 50 times, flashing different combinations. Still it goes back to brick mode.. backlit-on&off-then-back-to-solid-red-led cycle.
i'd like to add that i have also tried flashing via fastboot mode using Flashtool. (thunder icon+selecting 'fastboot mode'). i have flashed the kernel and system, tried kernel only, tried both same time, tried system with boot.img tried flashing kernel with boot.img too, tried different combinations. again, all were successful, but still same result.
it only goes back to backlit-on&off-then-back-to-solid-red-led cycle.
a couple of days after it went to green. flashmode finally! thinking everything will now be alright, i decided to flash it using flashtool via flashmode. I connected phone to pc, after the solid red led and after backlit-on&off-then-back-to-solid-red-led cycle. and the it goes back to red led then the backlit on&off cycle, after observing my phone for hours i then knew that after, i guess about a hundred cycle of backlit on&offs it really does go to green led by itself and if i'm connected to the pc and flashtool it stays on green led or flashmode, however if im connected only on a wallcharger it goes to green led but will only stay there for like 1-2 seconds then goes back to red led and then the backlit on&off cycle.
then i thought just maybe my battery really needs to die as mentioned, since upon plugging my phone on to a wall charger it goes immediately to red led and there's really no response on the phone except only if you gonna wait for the backlit on&off cycle the n press power + vol up then it will respond and go to fastboot mode or power+vol down which goes to flashmode. then i decided to reset the battery by carefully unplugging the ribbon cable and i did. well, initially it did (led was off for a moment then changed to blinking red then solid red) but i have to go to work that time and had to continue only after coming home from work, and that did not resolved it.
i may have flashed my ion a hundred times or so to this date, still no luck. i have finally decided to re-locked my bootloader- and yes it is successfully locked now. - thinking PCC/SEUS/SUS would get it back to life but i'm wrong - it just cant detect my phone. PC companion detects it as Phone/Tablet only then after selecting Ion on the phone list it always says my device is upto date and no available software. (sad)
I also noticed that flashtool does not detect my phone as LT28h. It only says that it is connected to flashmode. Is that an issue too. I have tried diff versions of flashtool from 9.6 to 9.11 all same. i have also installed fastboot and adb as well as flashtool drivers, it sayas all were successfully installed however if im connected via flashtool flashmode, none seems to be detected on device manager, tried reinstalling and manually installing the sony sa0103 adb interface driver however after installing i get an error unable to start device. even if my phone is connected still the device on devicemanager still has an excalamation point. i'm using windows 8. i have flashed successfully before when my phone was in good state, however now that im on brick mode it seems that all flashes i've done did not push thru. also those times that i have flashed my ion via flashtool it says something like:
phone should be connected with usb debugging on and enabled install on unknown sources. i have tried flashing it using win7 pc phone was not detected still, however flashtool stated and detected my device was connected on usb debugging mode, but have has errors during flashing though.
since my bootloader is now locked im unable to flash now via fastboot. before bootloader status says- rooted now bootloader status is- ROOTABLE.
i previously owned xperia neo and have managed to flash it successfully without any issues, also this is the 3rd time i had bricked my ion and managed to fix it before..
i also want to ask regarding flashing back to stock - does that mean any stock firmware can be selected? can be .233 / .68 /.20 or the latest ICS 6.1.E.3.7? coz i have basically tried to all of those mentioned. also is the reason that my flashes were not successful is it because i was currently on 4.1 JB ROM and im flashing 4.0 ICS stock? I also have TWRP and CWM backups on my PC and on internal SD card, is there a way for me to flash or restore those backups via flashtool?
I'm running out of options, i'm desperate and on the verge of giving up.
i dont want to believe that i have totally messed up and hard bricked my phone. I do believe that there is a solution to this, and my phone can be recovered without sending it over to repairshop.. Today is the 3rd week and still struggling to get my phone back to life (even just the sony logo) . any suggestions before i unlock again my bootloader? please help. Any help will be gladly appreciated, and many thanks to everyone for spending time on reading my messed up and soft/hardbrick ion experience.
If you brick your device while flashing kernel and device do not respond any way then follow this little difficult but 100% sure method.
- Dissemble your phone.
- Disconnect battery ribbon from motherboard.
- Reconnect battery ribbon.
- Fastly connect USB cable while holding vol +/-
- Flash Kernel or FTF FW.
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Droiiiiiiiiid said:
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Click to expand...
Click to collapse
Did you try SUS ? Official update service ?
Droiiiiiiiiid said:
Just looking for some direction on my Xperia Ion that recently got bricked while attempting to update to JB software.
Currently, it has no response except for plugging into charger giving a solid red light. I am unable to get it into flashmode and have already disassembled and disconnected/reconnected the battery to reset it.
Im gonna guess that the kernel is royally efed up at this point, Im unable to get it into a bootloop either.
What is the next step to solve this issue? Any help is greatly appreciated!
Click to expand...
Click to collapse
I think that you should charge it more to be able to go into flashmode. Maybe until the red light will go off or it'll turn into green. Then try to go into flashmode. Good luck
MozzieZ said:
Did you try SUS ? Official update service ?
Click to expand...
Click to collapse
I was going to but that requires my device be in Flashmode.
Droiiiiiiiiid said:
I was going to but that requires my device be in Flashmode.
Click to expand...
Click to collapse
Read this, maybe it will help you.
http://forum.xda-developers.com/showthread.php?t=2344896
This is my first time got hard brick on my phone. I'm flash wrong ROM (it made for S but I flash it on SL) now my phone totally dead. When I put on wall charger it show constant red led and off several minutes later, try disassemble phone and disconnect and connect ribbon doesn't help to get flashmode and fastboot mode. Any help would be very appreciated.
EDIT: After disconnect ribbon battery I got notification on flashtool "device connected with usb debugging off" but led remains on constant red. Should I try rubber band tricks?
ahlulnugraha said:
This is my first time got hard brick on my phone. I'm flash wrong ROM (it made for S but I flash it on SL) now my phone totally dead. When I put on wall charger it show constant red led and off several minutes later, try disassemble phone and disconnect and connect ribbon doesn't help to get flashmode and fastboot mode. Any help would be very appreciated.
EDIT: After disconnect ribbon battery I got notification on flashtool "device connected with usb debugging off" but led remains on constant red. Should I try rubber band tricks?
Click to expand...
Click to collapse
After disconnecting and connecting back the battery cable , you wont get access to flashboot/flashmode instantly. disconnecting the cable will reset the phone.
If you are getting red led means , its charging on low power. You should keep on wall charging for some hours , say 12 + hours.
After that try flashing the kernel alone , first . you will have to hold the flash mode button for sometime. say 5-10 minutes. then if u have enough charge in your phone it will flash the kernel alone. if u are successful in flashing the kernel, then charge again for some hours , 2-4 hours then try to flash the entire ROM.
Read the Thread Recovering Bricked Phones. This will help. I recovered my phone following the method shown in that thread.
Be patient bro, you can recover your phone, just that it will take some time
Captain Droid said:
After disconnecting and connecting back the battery cable , you wont get access to flashboot/flashmode instantly. disconnecting the cable will reset the phone.
If you are getting red led means , its charging on low power. You should keep on wall charging for some hours , say 12 + hours.
After that try flashing the kernel alone , first . you will have to hold the flash mode button for sometime. say 5-10 minutes. then if u have enough charge in your phone it will flash the kernel alone. if u are successful in flashing the kernel, then charge again for some hours , 2-4 hours then try to flash the entire ROM.
Read the Thread Recovering Bricked Phones. This will help. I recovered my phone following the method shown in that thread.
Be patient bro, you can recover your phone, just that it will take some time
Click to expand...
Click to collapse
Thanks for your fast reply, but I'm already put on wall charger 1 day, and the red led got turn off (no led at all). I think I'll try rubber band trick tonight and leave it till morning.
Hey guys I'm having a problem with my Acro S... It's bootloader is unlocked.
It was soft bricked due to a command I ran on Terminal Emulator (dd if=/dev/zero of=/dev/block/mmcblk0). After inputting that command I safely turned off the phone (Long press Power button, Choose Power off). After turning off, phone was completely dead, no response. It was on 80% battery for sure. It happened last week Saturday (July 20). I then charged my phone for 2days+. On the first day (July 21), no red LED appeared, on the 2nd day (July 22), constant red LED appeared, 3rd day (July 23), red LED disappeared. I then prepared my flashtool for flashing the JB firmware .211 KERNEL ONLY. So I plugged in my phone with volume down pressed, I pressed it for 15mins! My finger was f*cked, after 15mins... nothing happened, RED LED just disappeared and I just heard the Windows USB sound. Flash process didn't start, phone didn't give me a GREEN LED. I tried it again and again and miserably same thing happens, can't go to flash mode. Tried the same with volume up button for fastboot mode but still nothing happens, the RED LED just disappears!
Should I just leave my phone charging on the wall socket even if the RED LED disappeared? To get green LED?
SOMEBODY PLEASE HELP ME! I NEED MY PHONE SO BAD! :crying:
i was installing the prerooted/deodexed stock lt28h rom through cwm in the middle of instalation my phone rebooted and came into a sony bootloop i forced it shutdown by pressing power and volume up now its not starting not even charginig what to do please help :crying::crying:
Flash Tool
Be calm and sit back now put your phone to charger for whole night and then next day download flashtool and a firmware for you device and fladh it your device will breath again.......
tejasvi1 said:
i was installing the prerooted/deodexed stock lt28h rom through cwm in the middle of instalation my phone rebooted and came into a sony bootloop i forced it shutdown by pressing power and volume up now its not starting not even charginig what to do please help :crying::crying:
Click to expand...
Click to collapse
we have desame problem my phone is not charging no ligths/led and cant power on after pressing power and up because im stuck in boothllop after afgrading via OTA.
theprint said:
we have desame problem my phone is not charging no ligths/led and cant power on after pressing power and up because im stuck in boothllop after afgrading via OTA.
Click to expand...
Click to collapse
thks for sharing but i have alraedy solved my hard brick problem my phone is back and running normally
I was trying to root the Xperia ION phone.
I followed all the the steps mentioned(HERE) & flashed the kernel available HERE.
BootLoader is unLocked
Now after flashing the kernel, the device had gone in bootloop mode.
I could access the recovery, but thats it.
When i tried to boot to system from recovery, it once again started bootloop.
So, from recovery i wiped the whole system partition of my fone {wipe data}.
Now there is not bootloop, when the phone starts it just gets stuck at SONY logo & after that it doesnt go any further.
While starting it displays a pink LED, so i can go into recovery by pressing VOL-UP key & from recovery i can go into BootLoader FastBoot Mode.
But i cannot get the green led to get into flash mode.
I dont know which type of bricked device is this HARD or SOFT BRICK.
But please help.
What should i do further so that i can again use the phone.
Currently the phone's battery is completely dead.
dharmil007 said:
I was trying to root the Xperia ION phone.
I followed all the the steps mentioned(HERE) & flashed the kernel available HERE.
BootLoader is unLocked
Now after flashing the kernel, the device had gone in bootloop mode.
I could access the recovery, but thats it.
When i tried to boot to system from recovery, it once again started bootloop.
So, from recovery i wiped the whole system partition of my fone {wipe data}.
Now there is not bootloop, when the phone starts it just gets stuck at SONY logo & after that it doesnt go any further.
While starting it displays a pink LED, so i can go into recovery by pressing VOL-UP key & from recovery i can go into BootLoader FastBoot Mode.
But i cannot get the green led to get into flash mode.
I dont know which type of bricked device is this HARD or SOFT BRICK.
But please help.
What should i do further so that i can again use the phone.
Currently the phone's battery is completely dead.
Click to expand...
Click to collapse
What firmware version were You on? I think using old kernel with new firmware made Your device soft brick. Try using a kernel which is of same firmware version as Your's.
Did You install drivers for flashmode? Because You need to flash the Your official firmware ftf via flashmode.
Else if You are able to access Your device on pc while being in recovery, find a rom with kernel in it and try the command:
Code:
push /pat/to/ROM.zip /sdcard
and then flash the rom.
Thanks buddy.
But i already solved the issue.
By going into the flashMode nd flashing the stock firmWare
Hello, I just got my g3 and decided to root it. I used stump root to do that, then installed twrp. I flashed the latest cyanogenmod rom and everything was good. this morning i opened the phone and now get a loop of
unfortunatly the process phone has stopped
I looked it up and the fix seems to be flashing the boot img to my phone via fast boot.
this is where I am having isues. i have fast boot on my computer, but I am not able to get my phone into fastboot mode, I tryed holding vol up while plugging in the usb, but that just turned the phone on normally. I tryed a few other things that I really don't remember, but now I can get the phone to a screen that says Firmware Update. butfast boot wont recognize my phone is there when I type fastboot devices. please help, I'm not very good with this so any instructions need to be dumbed down and maybe a pic of what my phone screen should look like would help
tekkaman_01 said:
Hello, I just got my g3 and decided to root it. I used stump root to do that, then installed twrp. I flashed the latest cyanogenmod rom and everything was good. this morning i opened the phone and now get a loop of
unfortunatly the process phone has stopped
I looked it up and the fix seems to be flashing the boot img to my phone via fast boot.
this is where I am having isues. i have fast boot on my computer, but I am not able to get my phone into fastboot mode, I tryed holding vol up while plugging in the usb, but that just turned the phone on normally. I tryed a few other things that I really don't remember, but now I can get the phone to a screen that says Firmware Update. butfast boot wont recognize my phone is there when I type fastboot devices. please help, I'm not very good with this so any instructions need to be dumbed down and maybe a pic of what my phone screen should look like would help
Click to expand...
Click to collapse
download the drivers for your phone(google it)
Hi,
Recently my devices start to boot loop suddenly so, i decide to flash the custom rom back.after flashing the custom rom,the device still boot loop then i try to get into TWRP Recovery mode but it would not appear, then i proceed to flash the TWRP Image recovery (suspecting the recovery already missing during the flashing rom ) via FASTBOOT once the process done, i had disconnect the cable and suddenly the device screen wouldnt turn on even though i pressed the power button for a long time.
Please help.
Thanks.
asen[email protected] said:
Hi,
Recently my devices start to boot loop suddenly so, i decide to flash the custom rom back.after flashing the custom rom,the device still boot loop then i try to get into TWRP Recovery mode but it would not appear, then i proceed to flash the TWRP Image recovery (suspecting the recovery already missing during the flashing rom ) via FASTBOOT once the process done, i had disconnect the cable and suddenly the device screen wouldnt turn on even though i pressed the power button for a long time.
Please help.
Thanks.
Click to expand...
Click to collapse
Connect phone with PC and check if you Notification light turn on or not.
If it's still on, your phone got hard bricked (maybe because you mess with custom roms and TWRP). Next time follow Flash guide in each custom roms.
You can use unbrick hardbrick method (free) or get service (paid). I recommend try free method first but when use SP Flash tool, remember ONLY use "Download Only" (Some stupid local shop can use Format and you can lose IMEI too, so careful).
You can find that method easily on: Youtube, XDA, Github, Telegram,...
If you have any error, you can reply here or join Telegram group to get help.
hi i already using SP Flash tool but i stuck at this level..