Hi everyone, i broke the screen of my phone (mi A2 lite)
The only video that i could find to replace my screen was this one : https://www.youtube.com/watch?v=qRE6Dc93zvY
(Redmi 6 Pro is another name for the a2 lite)
The screen seems to be just below the motherboard and it seems extremely difficult to replace it !
Am i missing something ?
Any help will be very useful, i really like this phone !
Thanks a lot in advance,
Samt434
That video is your best guide currently. Yes you will have to remove the motherboard and battery to replace the screen.
Make shure you get the full display assembly including the frame like here. Then you only have to follow the instructions from the video. Hope youre successfull!
Hello I have changed my display according to video and almost erverything works like it should be...
Everytime I recive or make a phone call display goes down, and It doesn't light on.
Have I done something wrong? I've moved all components to new display ( according to video ).
Tanks
JoaoRib
Used the video to replace my screen, thank you !
I don't have the same problem as you, light going down during phone call.
JoaoRib said:
Hello I have changed my display according to video and almost erverything works like it should be...
Everytime I recive or make a phone call display goes down, and It doesn't light on.
Have I done something wrong? I've moved all components to new display ( according to video ).
Tanks
JoaoRib
Click to expand...
Click to collapse
Sounds like a proximity sensor issue to me... Check if you plugged correctly all the flat cables.
I had a Mi A2 Lite for screen replacement yesterday. Check if you placed the rubber part which goes around the sensor correctly. There s a very small part which you need to align correctly or your sensors get covered.
Numb digtizer
Hey Guys,
Also tried to fix my a2 lite. Now some time after the repair I noticed, that my digitizer is unresponsive in a 1cm wide row in the middle of the screen. Everything else works perfectly fine.
Do you have any ideas of the course of this? My suggestions are:
The Tape i used to glue he battery back in was to thick and now is pressuring the screen.
I did not connect to the cable correctly
The screen was broken before
Do you have an other idea? the
Is the A23 Lite supposed to have gorilla glass or something similar? Bought oen second hand where the seller said he had it replaced professionally, but I recently slightly bumped it, and it already cracked. Making me think its one of those cheap fakes from China.
-MB- said:
Is the A23 Lite supposed to have gorilla glass or something similar? Bought oen second hand where the seller said he had it replaced professionally, but I recently slightly bumped it, and it already cracked. Making me think its one of those cheap fakes from China.
Click to expand...
Click to collapse
Gorilla glass is scratch resistant, not hit and bump resistant...
TheoXSD said:
Gorilla glass is scratch resistant, not hit and bump resistant...
Click to expand...
Click to collapse
Not true whatsoever, I had many phones with it and they survived many hits and bumps, this one cracked at the slightest tap already, in fact, I actually accidentally did it again and it cracked again at a different spot, and it was barely hit even. It's definitely cheap glass.
JoaoRib said:
Hello I have changed my display according to video and almost erverything works like it should be...
Everytime I recive or make a phone call display goes down, and It doesn't light on.
Have I done something wrong? I've moved all components to new display ( according to video ).
Tanks
JoaoRib
Click to expand...
Click to collapse
I know this is old but did you ever get it sorted out? I ran into the same issue when I replaced my screen. However I followed this guide and the sensor works as it should.
I was able to buy a new A2 Lite screen & frame for $20. I just swapped everything into the new frame by following the video in the first post (as well as Googling for other tear downs). Process was fairly easy...just made sure I watched and understood which part was which. Actually, the hardest part was getting the battery out. When I was pulling the tape out it broke and kept the battery secured very, very well. Anyway, took about an hour but now I have a perfectly good phone again!
Thanks for sharing the link in the first post to get me started.
Related
I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB
Hi everybody,
I have problem with my HTC Touch Pro 2.
It was fully working until I damaged my LCD screen and digitizer.
So I ordered a new one LCD and digitizer from ebay. I changed old lcd and digitizer, booted up my HTC and everything looked allright. But problem came soon. Touch screen can't recognize my touch exactly. For example, if I click on something, digitizer solve it allways about 2-3mm higher. So I can't click on start, battery and every other click is moved about 2-3mm higher.
I made a calibration, but without any effect. I made a hard reset and than a calibration, problem still same.
And if try to make a new calibration (after first calibration after HR), I click on first cross (in the middle of screen), then up-left corner, down-left corner, down-right corner, up-right corner and nothing happens, I have to click on first cross again... and whole procedure again... So I have to make a HR and try to make a new calibration... still same problem.
Could anybody help me please? I'm going crazy, because I like my HTC and I can't use it anymore.
Is there any other way to make a calibration or how can I repair it?
ROM:
Energy.RHODIUM.29022.Sense2.5.Cookie.2.0.Jul.04.7z
(I have this ROM before I damaged LCD screen, any it worked fine)
It almost sounds like the screen/digitizer aren't lined up correctly... Just my .02.
arrrghhh said:
It almost sounds like the screen/digitizer aren't lined up correctly... Just my .02.
Click to expand...
Click to collapse
Thanks for reply.
Ok, then It seems to be a HW problem between screen and digitizer?
So what can I do now? Try to repair it again?
How can I check, if digitizer is OK? or could be digitizer bad at all?
washa_rednecks said:
Thanks for reply.
Ok, then It seems to be a HW problem between screen and digitizer?
So what can I do now? Try to repair it again?
How can I check, if digitizer is OK? or could be digitizer bad at all?
Click to expand...
Click to collapse
I'm just guessing from your description. I've never actually replaced the screen... If the two have to line up perfectly, I would ensure they are lined up correctly. Perhaps try slightly moving the digitizer down...
arrrghhh said:
I'm just guessing from your description. I've never actually replaced the screen... If the two have to line up perfectly, I would ensure they are lined up correctly. Perhaps try slightly moving the digitizer down...
Click to expand...
Click to collapse
Ok, thanks. But I can't move with a digitizer, because it is in fixed position. Maybe I can move with a screen under a digitizer, but then I will not be able to see whole screen (digitizer has a black edge/margin/border).
Any other suggestion?
washa_rednecks said:
Ok, thanks. But I can't move with a digitizer, because it is in fixed position. Maybe I can move with a screen under a digitizer, but then I will not be able to see whole screen (digitizer has a black edge/margin/border).
Any other suggestion?
Click to expand...
Click to collapse
Nope, all I got. Calibration always works perfectly for me - if calibration doesn't work, there certainly must be some hardware problem. You replaced the screen, unfortunately you must establish where the hardware issue lies.
I don't have any help for you, sorry, just jumping on the wagon. My touch screen worked fine for a year but is now way off (1.5-2 inches sometimes) without having damaged the screen to my knowledge. I've switched roms (from MR.X to Mighty) and hard reset. If I try to calibrate it just keeps running through the process. Should I try to replace the digitizer? I plan on getting an iPhone if possible on Sprint in the coming month but would like to sell this for at least a little bit.
To both of you guys - have you ensured there's nothing between the screen or digitizer? Nothing that is wedged on the edge of the screen...?
I know some had reported complete screen failures just from some gunk that got wedged on the side of the screen.
arrrghhh said:
To both of you guys - have you ensured there's nothing between the screen or digitizer? Nothing that is wedged on the edge of the screen...?
I know some had reported complete screen failures just from some gunk that got wedged on the side of the screen.
Click to expand...
Click to collapse
Thought about that, but dismissed the tiny little amounts of gunk on the edge..currently searching for a toothpick or something small to clean out the edge. Thanks for the idea! Will report back.
Thanks so much arrrghhh! Found a small pin and got out most of the dust/gunk that was between one side of my phone. Apparently that bezel side is just a little bit looser. You saved me lots of time and money! Thanks. Always helpful on here and PPCGeeks.
Edit #2: Must still be more junk because the 100% functionality just went away. Time to clean it again
Hi,
I've just replaced screen digitizer on my gf's Galaxy Ace II, which was run over by a car, but I have issues with it.
The problem is that the upper half of the display doesn't react to touches at all. Well, except for the very upper left corner,
so the status bar can be dragged down, although not 10 out of 10 times. The lower half of the display works without problems.
I was very careful during the replacement procedure and I alligned the digitizer's connector with the line on the motherboard.
I didn't use force at all (except for the disassembly), used no sharp tools and I didn't bend anything at all, so I believe I haven't physically
damaged the screen.
I suspect the unit I received may be faulty, although I highly doubt a cheap non-original screen sent from china could be faulty :laugh:
But before I am marked a fool for trusting eBay, is there anybody with the same issue and possible solution? Is there a possibility it just
needs recalibration, or hard reset?
Any help would be appreciated. I said to my gf I can handle that and don't want to disappoint her
Thanks in advance
Omg! How did your phone manage to run over by a car,!! Give it to Samsung! Don't try doing anything by yourself!
info
hy, maibe this link will hep you
http://www.sweet-apps.net/2012/10/1...el-on-a-samsung-galaxy-ace-2-nfc-model-i8160/
b0g said:
hy, maibe this link will hep you
http://www.sweet-apps.net/2012/10/1...el-on-a-samsung-galaxy-ace-2-nfc-model-i8160/
Click to expand...
Click to collapse
I couldn't find a guide myself, so I had to improvise, however I managed to do it the same way as it was described in the tutorial, except for
chipping the glass parts of the screen off. The problem is most probably in the screen digitizer. I already contacted the seller and he offered
to send me a new screen, however I can't be sure it will be working properly.
But thanks for the link, at least I can be calm that I haven't screwed anything during the process
Hello!
Today dropped my phone and screen got covered in spider web. The display itself looks fine, but its covered it spiderweb. The touchscreen doesnt respond at all.
What do i need to do now? I looked at local repair shops, they ask atleast 100 euros. But on ebay i can find lcd display+screen digitizer for 55 euros shipped, or screen digitizer starting from 10 dollars!
Can i buy only screen digitizer (as i understand that top layer of glass thats cracked is screen digitizer?) and replace it? Or changing LCD display along with screen digitizer is a must?
http://www.ebay.com/itm/NOIR-VITRE-...Pièces_de_rechange_outils&hash=item27f98e5d31
So this should fit..right? And are all 3 models LS970, E975 and e973 really same size? Cuz i`ve read people have got smaller screens than original from some sellers on amazon.
Replacing a digitizer is pretty hard and time consuming, that's why people usually replace the whole lcd+digitizer+glass assembly. You will also need adhesive and a heater/appropriate tools. It can be a great learning experience if you don't mind potentially busting your phone. There are no shortage of instructionnal videos on youtube on the subject.
Also, a new G2 is only 190$US .... Just saying ...
noxlord said:
Replacing a digitizer is pretty hard and time consuming, that's why people usually replace the whole lcd+digitizer+glass assembly. You will also need adhesive and a heater/appropriate tools. It can be a great learning experience if you don't mind potentially busting your phone. There are no shortage of instructionnal videos on youtube on the subject.
Also, a new G2 is only 190$US .... Just saying ...
Click to expand...
Click to collapse
As i have two other phones. The g2 mini with Tegra and a razrHD. I'll give a try, thanks for the tip.
Well, i ended up ordering that LCD+Digitzer from ebay. Everything was fine for 2 months, now i have quite large spot that doesnt respond to touches. (See attachment) i already tried disconecting the lcd and digitizer..still same. Is it worth trying to flash another rom? I already flashed stock kdz (had stock before too..)
This happened just today, right after ghost touches went crazy and rondomly oppening everything.
EDIT: That spot is changing sizes..form remains, but it got a bit smaller now. Its truly weird. I put the phone outside for few minutes (its +9C outside) and touchscreen works fine now! What is going on?
EDIT 2: After few minutes of usage, the spot is coming back
WreckLv said:
EDIT: That spot is changing sizes..form remains, but it got a bit smaller now. Its truly weird. I put the phone outside for few minutes (its +9C outside) and touchscreen works fine now! What is going on?
EDIT 2: After few minutes of usage, the spot is coming back
Click to expand...
Click to collapse
I had dropped my LG (more than a couple of times) on its face and it seemed to suffer stroke-like symptoms: one side of the screen was completely dead to touch, and the rest of the screen would occasionally act as though I was touching everywhere which opened programs and messed with the keyboard. I was stubborn and just lived with it and over time, it stopped trying open programs and whatnot. Recently, dropped it again, this time it was a bit more serious. Still no visible damage to the screen, but the "dead spot" moved to the centre of the screen, and again, occasionally tries to open programs and add words to my messages.
At first I thought it all could be related to a software issue. Unfortunately, after installing new ROMS, it never fixed the problem. I bought a digitaliser screen from Ebay as well. I'm waiting on the adhesive tape still so I can't say if this will fix anything. I kind of have a suspicion that its a loose connector (the top middle part of the screen gets super hot only after a couple of minutes of being left on).
I'm just wondering if you have tried taking it apart again to recheck the wiring? I think we may have similar problems (your situation is the first I've come by on the internet that is anywhere close to what's happening to my screen). Thanks so much!
Well, after a couple of weeks with my shiny new ZE551ML (RAM 2GB) purchased overseas in a trip, today the big bastard fell and cracked the glass .
So a new screen (complete screen, even if touch and LCD still works but don't want to mess with heat gun) is on the way via Aliexpress, I've done some similar procedures on more complicated phones but can't find any official procedure or documentation for this one, maybe too new?
So anyone has a PDF or webpage with the procedure?
Best I could find is this, but many pictures are missing
http://www.ewisetech.com/Pages/Product/teardown.aspx?s=1961&dt=6820&img=65699
EDIT: See post #6
http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
Bout the best one available at the moment. Looks fairly simple to do, especially if you are replacing the entire screen assembly, not just the glass.
Sammaul said:
http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
Bout the best one available at the moment. Looks fairly simple to do, especially if you are replacing the entire screen assembly, not just the glass.
Click to expand...
Click to collapse
Thanks, at least it's better than the one I found. But no specifics instructions on replacing the screen (separating the last housing from the old panel. Glue? Heat Gun? Double tape?)
gipikay said:
Thanks, at least it's better than the one I found. But no specifics instructions on replacing the screen (separating the last housing from the old panel. Glue? Heat Gun? Double tape?)
Click to expand...
Click to collapse
I do not know unfortunately. I would think it is tape, as most tend to be tape, but I couldn't say for certainty.
If you would like to set up an Out-of-Warranty RMA for ASUS to repair please send me a private message at [email protected].
Or you may apply for an RMA online at http://www.asus.com/us/support/
Please ensure to mention the damage otherwise it will be rejected if received with no reported damage.
Sincerely,
Frank
ASUS_USA
Here's an album I've used to replace my screen, (pictures are from the first link I've posted before) there are a couple of things to consider that aren't one these pictures nor any on the internet and don't make the sames mistakes I did. If you have pictures, and working screens from a different seller, please post it and I'll add it to the thread .
http://imgur.com/a/Rmy02
The tools I've used are screwdriver, a metal spudger, double-tape for cellphone repair, and a heat gun. And of course, your replacement screen. In my case I've purchased for 30 dol. on Aliexpress, but did not come with adhesive or tape so you have to have your own.
To remove the first section (4th picture), not only do you need to remove the cover and black and silver screws, but be careful because the center "rails" (the plastic parts to the sides of where the double sim and sd-card are) of the section are fixed to the battery section with "light" double tape, nothing too strong and can be lifted with care.
In the 5th picture, lift the white part of the connector and very carfeully to remove the ribbon. I've made the mistake to be too forceful and cracked the black part a litlle bit.
WARNING! THIS STEP IS THE MOST DIFFICULT, MANY PEOPLE BREAK THEIR BATTERY WHEN REMOVING, SO BE CAREFUL. AGAIN, YOU'VE BEEN WARNED
Now, one of the most difficult parts of the teardown is between 5th and 6th picture. After removing the uppers ribbon you have to take the battery compartment, and let me tell you that the white double-tape that glues the battery to the frame is one of the strongest i've ever encountered. A metal spudger can be helpful and you can start with pressing the left side, but don't separate too much or go too deep cause you might damage the envelope of the battery (I scrapped and exposed a litlle bit of the cells, but for the moment the phone works and don't heat. Just in case, I already ordered a new battery) . So be extra careful on this step.
In the 7th picture, things looks a little different of what I've found, the upper board has a metal protection that's soldered so DON'T TAKE IT OUT! Remove the upper left small ribbon very carefully. The cables on the down board that connects to the vibration motor are very fragile so be careful.
At this point, you can remove the speaker (I didn't) and you have the upper section, so the real hard work starts to be able to replace your screen. I'm sorry but i didn't take many pictures of this procedure, but again a metal spudger was helpful to be able to separate the cracked screen from the frame.
Remove all pieces of glue, glass or residue that's still on the frame and put the first part of the double-tape on the frame but don't take the upper part just yet. Take the replacement part and check it fits on the frame, paying atention to the two ribbons, one in the middle and other in the upper side. In my case, when I did put the screen I started with the upper ribbon and then guided the middle ribbon to it's hole and then fit the screen to the frame.
Make all the steps in backward order to be able to re-assemble the phone. The final optional step I did, is to seal the double-tape in the screen with the heat gun and some weight (I used a 2.5 drive and a couple of 3.5)
So in the end, I managed to replace the screen with only a couple of small mistakes. When my new battery arrives, the steps will be similar (I removed the white strong double tape with a light adhesive one, so it will be more easy to remove and replace the battery).
All in all, it went pretty well
LIST OF SELLERS WITH WORKING PARTS, according to users
AliExpress - Shenzhen OMG Trade co.,LTD - Screen For ZE551ML - USD 22.39 - gipikay (OP)
Nice to see someone succeeded, I laughted at the big hard drive lol Those 3.5'' HDs are huge. 30$ for the 5.5'' 1080p screen is pretty good, there are for 20$ too.
I tried once replacing an iphone 4 lcd but the problem ended up to be the motherboard.
btw Does anyone know where is the Intel GSM modem located on the motherboard? I see nothing from those pictures about the modem. I could not find a reliable way of disabling it, tried scripts, deleting dial etc apks and /lib/ril files, cellphone still searches for signal with no sim inserted and airplane mode on.
Back when I ordered, this one was the cheapest and the only one for ZE551ML (now the same vendor lists the screen as USD 25).
If I could guess, the modem should be in the upper board, under the metal shielding (the stock pictures indicates two visibles intel chips under the enclosure, maybe a third in the right, and one down in the board)
Thanks, so will it need to be unsoldered for removal? I only use voip and cannot use gsm anyway.
Experienced basically the exact the same when i changed my display essambly. I broke the foil around the battery too, only problem is I can not find any vendor selling a replacement battery. Can you give me a hint where to buy it?
Thanks in advance!
Gesendet von meinem ASUS_Z00AD mit Tapatalk
gipikay said:
Back when I ordered, this one was the cheapest and the only one for ZE551ML (now the same vendor lists the screen as USD 25).
If I could guess, the modem should be in the upper board, under the metal shielding (the stock pictures indicates two visibles intel chips under the enclosure, maybe a third in the right, and one down in the board)
Click to expand...
Click to collapse
Did you replace the glass only, or the entire screen assembly?
gettohhole said:
Experienced basically the exact the same when i changed my display essambly. I broke the foil around the battery too, only problem is I can not find any vendor selling a replacement battery. Can you give me a hint where to buy it?
Thanks in advance!
Gesendet von meinem ASUS_Z00AD mit Tapatalk
Click to expand...
Click to collapse
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
EDIT: I leave the link, but this seller sent me the wrong battery, see post #21. Now I'm waiting for AsusParts to ship me a new replacement
http://www.aliexpress.com/item/Free...ENT-BATTERY-C11P1424-3000MAH/32396187338.html
Sammaul said:
Did you replace the glass only, or the entire screen assembly?
Click to expand...
Click to collapse
Entire screen replaced, to separate the glass is really difficult
gipikay said:
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
http://www.aliexpress.com/item/Free...ENT-BATTERY-C11P1424-3000MAH/32396187338.html
Entire screen replaced, to separate the glass is really difficult
Click to expand...
Click to collapse
If you install 550 screen on 551 phone, it's possible you must install rom for 550 on 551, the big difference is the dpi.
I was just commenting on batteries. My phone is 551 and used a 551 replacement LCD, no differences there
Ok sorry just my bad english
gipikay said:
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
Entire screen replaced, to separate the glass is really difficult
Click to expand...
Click to collapse
gipikay said:
I was just commenting on batteries. My phone is 551 and used a 551 replacement LCD, no differences there
Click to expand...
Click to collapse
Did you test it already? Does work?
Sent from my ZE551ML
gettohhole said:
Did you test it already? Does work?
Sent from my ZE551ML
Click to expand...
Click to collapse
The new battery has not arrived yet
But a couple of scares aside ( if I completely drain the battery, it takes a litlle longer to reach minimal charge to power on ), the old battery seem to hold for the moment.
EDIT: See post #21, the sellers sent me the wrong battery, I think it's for Zenfone 5. Now I'm waiting for AsusParts to ship me a new replacement
Be careful
If anyone tries this, use extreme caution. I exposed some cells on the battery and a little smoke came out. I don't really know what to do from here because I'm afraid to continue this further. I guess I'm out of a 300 dollar phone and 30 dollar screen
Hi all
I ordered ZE551ML for my ZE550ML .... and the person already shipped so couldn't change the order
is it ok or i have to ship it back?
is it only PPI and resolution ?
Hi guys
Failed ... Got the 551ML and mounted on 550ML
Screen turns on but no Asus initial logo etc... Is not working
Mounted all out of the box... Not removing completely the broken screen.
Main board and battery connectors only.
You guys think anything can help ?