Related
Hello All!
After much frustration with setting up ADB i finally got it working. Everyone said its simple and takes minimal knowledge but when things dont work, nothing really worked. Anyways after 2 hours of research trying to get ADB to work i finally got it all working and wanted to share my knowledge to anyone else that needed help.
This Guide is for windows only. If you are using Mac OS X please go here: ADB For Dummies
If you are using Linux please go here: [HOW-TO]Set up Android SDK/ADB/Fastboot on Ubuntu Linux
Like My Guide(s)? Donate
--------------------------------------------------------------------------
Things you need:
Android SDK - Download
Winrar - Download (32bit) Download (64bit)
Windows PC
USB Cable
A Rooted Android Device
--------------------------------------------------------------------------
Setting up the Android SDK
Download the file from above
Unzip to your desktop
Take the "android-sdk-windows" folder and move it to the root of your hard drive (C:\)
Right click on My Computer and click properties
Select the Advanced Tab or Advanced System Setting (Vista/Windows 7)
Select Environment Variables...
Press New
For Variable Name type: adb
For Variable Value type: C:\android-sdk-windows\tools
Now,
1. Run SDK Manager.exe located in the android-sdk-windows folder
2. If it gives you an error go to settings and click on "Force http//....."
3. Select all options and let it download and install
If you cant get the setup to work, Download the USB-DRIVERS folder - HERE (Windows XP/Vista/Windows 7)
--------------------------------------------------------------------------
Preparing your phone for ADB
Go to Settings on your phone
Select Applications
Select Development
Make sure 'USB Debugging' is checked
--------------------------------------------------------------------------
Installing Drivers
Plug in your phone through USB and DO NOT MOUNT IT!!!!!
Your computer should see a new device and try to install Android 1.0 driver (If it doesnt, scroll down to the "Im not getting a notification of Android ADB when i plug in my USB" section)
Let it load
Once it cant find them select "Install drivers from my pc"
The drivers you need are in the Android SDK 1.5r2 folder (C:\android-sdk-windows\usb_driver)
Depending on your OS pick x86 or amd64
You ADB Android Device should now be installed! Good Job
For Android SDK 1.5r7+
1. Run SDK Manager.exe
2. If it gives you an error go to settings and click on "Force http//....."
3. Select all options and let it download and install
If you cant get the setup to work, Download the USB-DRIVERS folder - HERE (Windows XP/Vista/Windows 7)
--------------------------------------------------------------------------
Check if your phone is detected by ADB
Open up Command Prompt (Go to run, type in cmd, press enter)
Type in
Code:
cd C:\android-sdk-windows\tools === Press Enter
adb devices === You should see your device listed
adb shell === you should see # in the next line
Now you are all set to run adb commands
Note: for a list of commands type in 'adb' in cmd
CONGRATS YOU NOW HAVE ADB FULLY RUNNING!
--------------------------------------------------------------------------
Droid Explorer by Camalot
Droid Explorer is a Windows software that will download, install, and setup the android SDK for you all in under a minute so you are ready to go. I use this on a daily basis. This amazing piece of software has tons of plugins and a built in file explorer for all your files on your phone! All you gotta do is download, install, and go!
Download Droid Explorer - Here
Install the program, and let it setup the SDK files for you
Connect your phone
Enjoy!
--------------------------------------------------------------------------
"Im not getting a notification of Android ADB when i plug in my USB"
Why: Your computer has detected your phone but as a protable device and as a storage device.
Fix: This took me a lot of research and time to figure out so this is what your are going to do.
First download USBDeview - Here
Unzip it
Run USBDeview.exe as Administrator
You will see all drivers being used on your computer
Highlight and Uninstall all drivers with the description have HTC Android (Should be 3 of them)
Right Click on the driver and press uninstall
Once done, Unplug your phone and plug it back in
You should now get the notification of the ADB device
Follow the steps above to install the drivers
Still not working?
Try this: Get ADB to recognize your myTouch 4G [Thanks importflip]
--------------------------------------------------------------------------
When Typing just adb in cmd you will get whats called a "usage doc" which gives you a lits of commands that you can use:
Code:
-d - directs command to the only connected USB devic
e
returns an error if more than one USB device is
present.
-e - directs command to the only running emulator.
returns an error if more than one emulator is r
unning.
-s <serial number> - directs command to the USB device or emulator w
ith
the given serial number
-p <product name or path> - simple product name like 'sooner', or
a relative/absolute path to a product
out directory like 'out/target/product/sooner'.
If -p is not specified, the ANDROID_PRODUCT_OUT
environment variable is used, which must
be an absolute path.
devices - list all connected devices
device commands:
adb push <local> <remote> - copy file/dir to device
adb pull <remote> <local> - copy file/dir from device
adb sync [ <directory> ] - copy host->device only if changed
(see 'adb help all')
adb shell - run remote shell interactively
adb shell <command> - run remote shell command
adb emu <command> - run emulator console command
adb logcat [ <filter-spec> ] - View device log
adb jdwp - list PIDs of processes hosting a JDWP transport
adb install [-l] [-r] <file> - push this package file to the device and instal
l it
('-l' means forward-lock the app)
('-r' means reinstall the app, keeping its data
)
adb uninstall [-k] <package> - remove this app package from the device
('-k' means keep the data and cache directories
)
adb bugreport - return all information from the device
that should be included in a bug report.
adb help - show this help message
adb version - show version num
scripting:
adb wait-for-device - block until device is online
adb start-server - ensure that there is a server running
adb kill-server - kill the server if it is running
adb get-state - prints: offline | bootloader | device
adb get-serialno - prints: <serial-number>
adb status-window - continuously print device status for a specifie
d device
adb remount - remounts the /system partition on the device re
ad-write
adb root - restarts adb with root permissions
networking:
adb ppp <tty> [parameters] - Run PPP over USB.
Note: you should not automatically start a PDP connection.
<tty> refers to the tty for PPP stream. Eg. dev:/dev/omap_csmi_tty1
[parameters] - Eg. defaultroute debug dump local notty usepeerdns
adb sync notes: adb sync [ <directory> ]
<localdir> can be interpreted in several ways:
- If <directory> is not specified, both /system and /data partitions will be u
pdated.
- If it is "system" or "data", only the corresponding partition
is updated.
--------------------------------------------------------------------------
Commands that you should know
adb push - Insert file to phone such as Stock.apk to /data/app_s
Code:
adb push <pathtofile.apk> <file system location> - Example: adb push c:\app.apk /data/app
adb pull - Remove file from phone such as Stock.apk from /data/app_s
Code:
adb pull <pathtofile.apk> - Example: adb pull /data/app_s/Stock.apk
adb install - Install app to phone
Code:
adb install <path to file> - Example: adb install c:/apps/apps2sd.apk
adb uninstall - Uninstall app from phone
Code:
adb uninstall <name of application> - Example: adb uninstall linda.apk
For more ADB Commands go - Here
--------------------------------------------------------------------------
Thats it for ADB! Congrats and if you have any questions please ask me or if anything is missing or not correct please tell me. I got all of this from research and personal experience.
Even after unstalling the HTC and myTouch 4G Drivers, when I plug my MT4G back in there's nothing to install. It automatically installs what it has to. I have no idea how to connect it with ADB.
I had to do this:
http://forums.t-mobile.com/t5/Operating-System-Software/HOW-TO-Get-ADB-to-recognize-your-myTouch-4G/m-p/540017
This is why after the temp root. I used root explorer to move the files to right folder . And then used the terminal app to do the rest. Really no need to use ADB..
Sent from my HTC Glacier using XDA App
Scoop24 said:
This is why after the temp root. I used root explorer to move the files to right folder . And then used the terminal app to do the rest. Really no need to use ADB..
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
I did that too but insmod said can not open wpx.ko every time. No idea why, worked perfect on my G2.
Sent from my HTC Vision using XDA App
Arcadia310 said:
Even after unstalling the HTC and myTouch 4G Drivers, when I plug my MT4G back in there's nothing to install. It automatically installs what it has to. I have no idea how to connect it with ADB.
Click to expand...
Click to collapse
You ran the HTCDriver exe that is on the SDCard? Did you go into Devices on your computer with your phone plugged in and see what it is showing up as?
setzer715 said:
You ran the HTCDriver exe that is on the SDCard? Did you go into Devices on your computer with your phone plugged in and see what it is showing up as?
Click to expand...
Click to collapse
It seemed to work for me when I copied the HTCDriver.exe from the storage card to my PC and install the drivers. My device showed up as some letters and numbers, which is ok I guess I have not named or done anything to the device.
Amazing write up. ABD has always gave me a hard time. I will be following this write up when I get time to root this. Thanks a lot!
Sent from my HTC Glacier using XDA App
Four things:
1. You don't need the generic drivers from the SDK package. I haven't even tried them. You need the HTC Drivers on the SD card.
2. I start adb by SHIFT-right clicking on the tools directory in the SDK folder and selecting 'start command prompt here' in the contextual menu. In order to see if things are working, just type 'adb devices' to see if the HTC device is connected.
3. I don't need to disable mounting of the device. I can adb and have the SD card mounted on the PC at the same time.
4. I don't see the need to add the environmental variable. Perhaps I've done something wrong, but theoretically, by adding this variable, you should just be able to type 'adb' in any command prompt window and have the system recognize adb. I can't seem to get that to work. So, instead I just do #2 above.
setzer715 said:
You ran the HTCDriver exe that is on the SDCard? Did you go into Devices on your computer with your phone plugged in and see what it is showing up as?
Click to expand...
Click to collapse
Yes I have, how exactly do I get into devices on my computer?
Sent from my HTC Glacier using XDA App
Arcadia310 said:
Yes I have, how exactly do I get into devices on my computer?
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
type
Code:
adb devices
in the command line
Arcadia310 said:
Yes I have, how exactly do I get into devices on my computer?
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
What does the output from typing "adb devices" give you?
grankin01 said:
What does the output from typing "adb devices" give you?
Click to expand...
Click to collapse
It says can not recognize ADB. I have had the SDK and ADB on my PC for months.
Arcadia310 said:
It says can not recognize ADB. I have had the SDK and ADB on my PC for months.
Click to expand...
Click to collapse
Sounds like you aren't in the directory that adb is in when you type it. try going into the tools directory in your sdk and run the command from there.
Arcadia310 said:
Yes I have, how exactly do I get into devices on my computer?
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
What version of windows are you running?
setzer715 said:
What version of windows are you running?
Click to expand...
Click to collapse
Windows XP. When i actually go to ADB and click on it it opens and closes within an instant.
Sent from my HTC Vision using XDA App
Arcadia310 said:
Windows XP. When i actually go to ADB and click on it it opens and closes within an instant.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
You don't click on it. It's a utility to use in command line. What it does is makes it easier to enter commands (along with some other useful stuff). Basically, anything you would type in terminal you can type in command line on your pc with "adb shell" pre-face. For example:
In terminal: cd /system/app
In command line: adb shell cd /system/app
Makes sense? You should really read up some guides out there
floepie said:
Four things:
1. You don't need the generic drivers from the SDK package. I haven't even tried them. You need the HTC Drivers on the SD card.
2. I start adb by SHIFT-right clicking on the tools directory in the SDK folder and selecting 'start command prompt here' in the contextual menu. In order to see if things are working, just type 'adb devices' to see if the HTC device is connected.
3. I don't need to disable mounting of the device. I can adb and have the SD card mounted on the PC at the same time.
4. I don't see the need to add the environmental variable. Perhaps I've done something wrong, but theoretically, by adding this variable, you should just be able to type 'adb' in any command prompt window and have the system recognize adb. I can't seem to get that to work. So, instead I just do #2 above.
Click to expand...
Click to collapse
Hey sorry about the driver problems... i wrote this guide based on the Nexus one and T-Mobile G1 and was asked to repost it here. If you let me know exactly what drivers you used i can change it in the OP.
The environmental variables set so that you can run adb and fastboot commands from anywhere in windows without have to be in the tools directory of the sdk. You can press SHIFT or w/e but this is a 1 time solution so u basically never have to be in that directory again...
As for the mounting, it is recommended that you dont mount your SD-Card and use adb for editing system files because that could corrupt your sd card.
Thank you, I got it working. Android is very different from winmo.
nephron said:
--------------------------------------------------------------------------
"Im not getting a notification of Android ADB when i plug in my USB"
Why: Your computer has detected your phone but as a protable device and as a storage device.
Fix: This took me a lot of research and time to figure out so this is what your are going to do.
First download USBDeview - Here
Unzip it
Run USBDeview.exe as Administrator
You will see all drivers being used on your computer
Highlight and Uninstall all drivers with the description have HTC Android (Should be 3 of them)
Right Click on the driver and press uninstall
Once done, Unplug your phone and plug it back in
You should now get the notification of the ADB device
Follow the steps above to install the drivers
Still not working?
Click to expand...
Click to collapse
This saved me... Constantly had it reverting back to USB storage device, this did the job. Thanks, a little something coming your way...
Bill
Hi, i install cannot turn on debbuging usb mode in my Defy 2.2 froyo movistar argentina.
Does anyone have any idea why? i turn on but when connecting to the PC no (!) icon shows.
Thanks!
btw, i belive is a device problem because before i install froyo work fine. And my drivers worked fine till i install froyo
Any idea? please help
Can you post the link/thread from where you downloaded the froyo ROM. Also ignore the ! icon, just check in ADB if debugging is working or not. Enable USB debugging in Settings and after plugging in the USB select "Charge Only" mode.
Open adb and type "adb devices"
if it shows one device, then you're all good.
PS: make sure you have Moto Driver v4.9 or above.
bikerabhinav said:
Can you post the link/thread from where you downloaded the froyo ROM. Also ignore the ! icon, just check in ADB if debugging is working or not. Enable USB debugging in Settings and after plugging in the USB select "Charge Only" mode.
Open adb and type "adb devices"
if it shows one device, then you're all good.
PS: make sure you have Moto Driver v4.9 or above.
Click to expand...
Click to collapse
Hi i'm using argentina movistar from http://and-developers.com/sbf:defy
I have tried what you 've told me and this is my cmd:
C:\Users\MaryPau\Documents\samsung\root>adb devices
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
015F13B80600D025 device
C:\Users\MaryPau\Documents\samsung\root>adb shell
$ adb push Superuser.apk /sdcard/Superuser.apk
adb push Superuser.apk /sdcard/Superuser.apk
adb: permission denied
There's nothing wrong with USB debugging or your cell. It's just that you're using the wrong command syntax.
once you type "adb shell" you DO NOT have to type adb before every next command because you're already inside adb prompt.
Just write "push Xyz.apk /sdcard/Xyz.apk"
or
write this command when inside windows prompt , i.e when not inside "adb shell"
C:\>adb push xyz.apk /sdcard/xyz.apk
(notice it's C prompt)
Skip writing 'adb' before each command once you are inside adb shell
also, are you trying to root your Defy?
bikerabhinav said:
There's nothing wrong with USB debugging or your cell. It's just that you're using the wrong command syntax.
once you type "adb shell" you DO NOT have to type adb before every next command because you're already inside adb prompt.
Just write "push Xyz.apk /sdcard/Xyz.apk"
or
write this command when inside windows prompt , i.e when not inside "adb shell"
C:\>adb push xyz.apk /sdcard/xyz.apk
(notice it's C prompt)
Skip writing 'adb' before each command once you are inside adb shell
also, are you trying to root your Defy?
Click to expand...
Click to collapse
it worked tks a lotttttttttttttttttt
RSD Lite recognize my phone, but after connecting no other options in Phone....No portal, No mass storage...Nothing.... Can anyone help..
1. Download and install Samsung_USB_Driver_for_Moblie_Phones_v1_4_6_0.exe
Link to download: http://www.multiupload.co.uk/YXE6FWLFAR
2. Download and install Android SDK (http://dl.google.com/android/android-sdk_r16-windows.zip)
3. With the phone turned OFF, hold VOLUME UP + VOLUME DOWN and power the phone on. This will put you in bootloader mode
4. Using windows/cmd go to the folder where Android SDK was installed (make sure that the folder android-sdk/platform-tools/ contains fastboot.exe and adb.exe etc....
5. using windows/cmd go to the folder /android-sdk/platform-tools
From this folder try the command "fastboot devices" (do not include ") which should list the device connected to your PC.
6. First we have to unlock bootloader,
use this command to unlock bootloader > fastboot oem unlock
(warning.. you will loose all data)
After the bootloader is unlocked the device will reboot normally.
7. Once normally booted from the command prompt issue the commands given below (after each command press enter button)
Note: you need su and superuse.apk (which can be downloaded from here: https://rapidshare.com/files/1319181583/su.zip)
unzip the downloaded file in the same folder where fastboot.exe exist i.e /android-sdk/platform-tools/
adb root
adb remount
adb push su /system/bin
adb push Superuser.apk /system/app
adb shell chmod 06755 /system/bin/su
adb shell chmod 06755 /system/app/Superuser.apk
adb reboot
Done!... your device is now rooted.
it would be good to note that many people have issues with the initial android driver installation.
if you install the drivers, but the phone doesn't show up after a period of time, open control panel -> system -> device manager and look for any devices that have a yellow triangle error (no driver). right click and open properties, and manually select the driver, not auto! the next screen will give you an option to 'select from a list', do this, and find SAMSUNG, then select the latest drivers.
after this, it can still take a minute or two the first time for drivers to install properly, you usually can see the status of this in the usb system tray icon.
if you rebooted to the bootloader (power vol(+) vol(-)), from the command line, if you type "fastboot devices" it should list a device and serial number. if not, you need to go check your drivers, something is missing. also, don't forget how magical a windows reboot can be at times : )
cancerouspete said:
it would be good to note that many people have issues with the initial android driver installation.
if you install the drivers, but the phone doesn't show up after a period of time, open control panel -> system -> device manager and look for any devices that have a yellow triangle error (no driver). right click and open properties, and manually select the driver, not auto! the next screen will give you an option to 'select from a list', do this, and find SAMSUNG, then select the latest drivers.
after this, it can still take a minute or two the first time for drivers to install properly, you usually can see the status of this in the usb system tray icon.
if you rebooted to the bootloader (power vol(+) vol(-)), from the command line, if you type "fastboot devices" it should list a device and serial number. if not, you need to go check your drivers, something is missing. also, don't forget how magical a windows reboot can be at times : )
Click to expand...
Click to collapse
Hi
Thanks for this note which would help many users.
Hi, noob here.
First of all, thanks for the guide.
I have already unlocked the bootloader about a month ago (up to step 6), but would like to root.
Will my phone lose all data again if I root the phone now? I'm not even sure what this actually does, but would like to learn and mess around with it.
You will not loose data. Rooting gets access your system folders by pushing su and superuser through adb.
Hope it helps.
Sent from my Galaxy Nexus using xda premium
smohanv said:
Note: you need su and superuse.apk (which can be downloaded from here: https://rapidshare.com/files/1319181583/su.zip)
unzip the downloaded file in the same folder where fastboot.exe exist i.e /android-sdk/platform-tools/
adb root
adb remount
adb push su /system/bin
adb push Superuser.apk /system/app
adb shell chmod 06755 /system/bin/su
adb shell chmod 06755 /system/app/Superuser.apk
adb reboot
Done!... your device is now rooted.
Click to expand...
Click to collapse
Did you actually test that with a stock rom?
Because adb root will not work with ITL41F at least.
Code:
./adb root
adbd cannot run as root in production builds
Furthermore the chmod for Superuser.apk is totally bogus. No need to mess with it's permissions.
i think a better way is get su and SuperUser.apk from the developers (ChainsDD) site and install it with a temporary boot CWM to install it.
(these instructions are also from memory And i rooted my one from source, but that's a bit involved)
this would mean instead of step 7 do.
7. Download CWM into the same directory as fastboot
http://download.clockworkmod.com/recoveries/recovery-clockwork-5.5.0.4-toro.img (Verizon)
or
http://download.clockworkmod.com/recoveries/recovery-clockwork-5.5.0.2-maguro.img (GSM)
Make sure to get the right version for your device.
8. download http://downloads.androidsu.com/superuser/Superuser-3.0.7-efghi-signed.zip
onto the internal storage of the phone( "sdcard" )
9. With the phone turned OFF, hold VOLUME UP + VOLUME DOWN and power the phone on. This will put you in bootloader mode
10. again using windows/cmd go to the folder /android-sdk/platform-tools
From this folder try the command "fastboot devices" (do not include ") which should list the device connected to your PC.
11. Start CWM (without installing it)
fastboot boot recovery-clockwork-XXX-XXX.img
(use the right filename from step 7)
12. choose install update and select the zip from step 8.
You need to use volume up/down to navigate and power to select.
I am not sure if this is the correct forum for this. Moderators, Please feel free to remove it or relocate it
First of all thanks to all amazing people on this forum ( thecubed,777jon,Dees_Troy, chainfire, supernoman, crashfocus, etc)
This is not my work . It is a compilation of what it worked for me from the work made by others. It is directly toward newbie users.
Instructions
1- Make sure you install LG G3 drivers in your computer( you can get them attached on this thread). Connect phone to the PC using USB cable. Make sure the phone is recognized when you plug it in with the usb cable
Also phone shall be connected as Media device (MTP), if it is in Charge Phone change it to MTP.
Scroll down this post. You will find the correct usb drivers attached. Install them in your pc.
2- Enable Developer options in your phone on Setting > General> About phone > Software information > and click seven times Build number until it enables it
3- Enable USB debugging on your LG G3 from your phones Settings > Developer options > tick ‘USB debugging’ check box. A window should pop up in your phone display to allow USB debugging. Select Allways Allow from This Computer and hit OK.
It will also be convenient to Enable installation of apps from Unknown Sources: Open phone’s Settings » select Security » Tick the “Unknown sources” check box (under Device administration section)
4- Download and unzip
- Pupledrake-Lite at http://downloads.codefi.re/thecubed/lg_g3/purpledrake/PurpleDrake-Lite_R03.tar.gz Thanks to Codefi.re
- Download and unzip the attached ADB LOCAL READY with TWRP recovery.img
Thanks to @Dees_Troy & TeamWin - for TWRP Touch recovery
ATTACHMENT IS HERE- JUST CLICK HERE
5- Download -Latest SuperSu at http://download.chainfire.eu/641/SuperSU/UPDATE-SuperSU-v2.40.zip Thanks to Chainfire
6- Transfer UPDATE-SuperSU-v2.40.zip to the internal sdcard
7- Open Purpledrake-Lite and Run purpledrake_windows.bat. It should detect your devices if it is not, you need to check if the drivers were installed properly and unplug-plug back your phone.
Hit Enter as instructed on the computer screen until it gains temporary root.
IMPORTANT : READ AND DO NOT CONTINUE TO PERMANENT ROOT INSTRUCTIONS DISPLAYED. FOLLOW INSTRUCTIONS TO CONTINUE WITH ADB INSTEAD.
Hit Ctrl+C to exit to use adb.
This process takes a few seconds and The phone start on download mode and it will stay on it.
8- Open ADB LOCAL READY folder you downloaded and hit Start Here.bat
Type "adb devices" to ensure that your phone is connected and it accept adb commands . On list of devices attached it should show LGD851........
Unplug it and plug it back if it is not .
NOTE: SOME PEEPS HAVE REPORTED PROBLEM WITH ADB NOT WORKING PROPERLY ON USB 3.0 PORTS. PLEASE USE USB 2.0 PORTS
9- Type "adb push recovery.img /temp"
You will see that it pushes the data. it should take a few seconds
Note: you may need to push it a few times if you do not find the recovery file on the /temp folder when you do step 12.
Some members stated that they need to push it ..5 times.
rubbamade tip
" This does work. If after you do the "adb push....", Hit the up key on your keyboard. What you just typed " adb push...." will appear again. Hit enter. It will "push" again. Hit up again. Hit enter. Do this at least 5 times. Now proceed with next step "adb shell"..... Should work now"
For some reason others user needed to push it more than 5 times, i assume that it is due to the file size of the image and your operating system and pc settings(i used win7). It is recommended to verify if it was pushed on step 12.
10- Type "adb shell" and it should go to shell command $
11- Then type "/temp/fakesu". This will put you in a superuser shell on your device. It should show su command line # .
12- Type "ls /temp" to make sure that recovery.img and fakesu are in /temp folder . If it is not, then you did not complete correctly the above instructions..repeat it
13- Type "dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery". it will take a few seconds to complete and install TWRP recovery.
14- Type type "reboot recovery" It should boot onto TWRP Touch recovery. it could take a few but it should
15- Once in TWRP, select install,go to the SD card directory, select UPDATE-SuperSU-v2.40.zip and install it. Reboot the phone once complete. Do not panic, it should take a while to cook and update applications, but it will, be patient.
16- Your device is rooted and with TWRP custom recovery. IF you do not see SuperSu in your application drawer, do not panic, just install it from the Play Store.
17- Now you are ready to install custom Roms, any application that requires root, or enjoy root features.
Quick References
How to Boot into TWRP(Recovery Mode)
1.Turn off your phone
2.Now, press and hold Power and Volume down buttons at the same time.
3.When the LG logo appears, release the keys.
4.Immediately press Power and Volume Down buttons again until the Hard Reset menu will be displayed.
5.Press volume down to Select "YES" on reset data. Do not panic, it will not . Select "yes" again . It will boot into TWRP recovery mode.
If you do not like hardware method you can use Quickboot or TWRP Manager applications from the Play store
How to Boot LG G3 Download Mode
-Disconnect your phone from PC.
-Power off your G3 and wait 4-5 seconds after lights go off.
-Hold the Volume Up button on phone, and while holding it, connect the phone to PC using a USB cable
If you get the "Windows cannot find '.\assets\windows\bin\mintty.exe'." error..on purpledrake temproot step 7.
Try just double-clicking on the .bat instead of running as admin.
Also make sure the script is extracted properly first before running
Disclaimer: It worked for me, but I am not responsible for any damages to your phone.
Your experience is very interesting vcurbel!
I was under the impression there was no way to root untouched stock 10R.
It would appear you have found a way! :good: Thanks for your contribution.
I am curious if anyone else has replicated this?
thank you so much had a little trouble but successfully rooted my device
Where was this guide yesterday?
Last week I just thought rooting build R was impossible as of yet, got fed up, and 5 minutes ago ran the LG Update tool to revert my phone back to stock/ Build C and root that way.
vcurbel said:
I am not sure if this is the correct forum for this. Moderators, Please feel free to remove it or relocate it
13- Type "dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery". it will take a few seconds to complete and install TWRP recovery.
Click to expand...
Click to collapse
dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
This command doesn't work for me. It shows, "cannot open for read: no such file or directory".
Can you help?
Edit: Nevermind, had to repush recovery. Didn't go through properly the first time. Thank you
Everything worked great. Thank you for the guide! Rooted on 10r!
NO GO
- Type "ls /temp" to make sure that recovery.img and fakesu are in /temp folder . If it is not, then you did not complete correctly the above instructions..repeat it
AT THIS POINT I AM GETTING "NOT FOUND". DID THE STEPS ABOVE SEVERAL TIMES.
I saw 8xxxkb data pushed after 'push'
==========================================================================================
C:\Users\nick\Downloads\ADB LOCAL READY>c:\windows\system32\cmd.exe
Microsoft Windows [Version 6.3.9600]
(c) 2013 Microsoft Corporation. All rights reserved.
C:\Users\nick\Downloads\ADB LOCAL READY>adb devices
adb server is out of date. killing...
* daemon started successfully *
List of devices attached
LGD851xxxxxxxx recovery
C:\Users\nick\Downloads\ADB LOCAL READY>adb push recovery.img /temp
9716 KB/s (11245568 bytes in 1.130s)
C:\Users\nick\Downloads\ADB LOCAL READY>adb shell
[email protected]:/ $ /temp/fakesu
/temp/fakesu
# Is /temp
Is /temp
/temp/fakesu: Is: not found
#
=========================================================================================
sharkoparko said:
- Type "ls /temp" to make sure that recovery.img and fakesu are in /temp folder . If it is not, then you did not complete correctly the above instructions..repeat it
/temp/fakesu: Is: not found
#
=========================================================================================
Click to expand...
Click to collapse
try to redo step number 7. But, you are getting into su command line which is #
after you do the ls/temp on su #, you should get the list of files in your temp folder.....check if recovery and fakesu are there
then continue to step 13
vcurbel said:
try to redo step number 7. But, you are getting into su command line which is #
after you do the ls/temp on su #, you should get the list of files in your temp folder.....check if recovery and fakesu are there
then continue to step 13
Click to expand...
Click to collapse
Thanks. I did it several times, I did number 7 also. Phone is found, it says creating permaroot....Once I click CTRL C screen disappears then I go to ADB file and follow procedures. IT STILL DOES NOT WORK
===================================================================================
Welcome to PurpleDrake!
Please ensure your phone is connected, powered on, and USB debugging is properly enabled.
Your phone should be showing your homescreen with no other apps open. This is to ensure a clean state.
When you're ready, press [enter]...
Press [enter] to continue...
Waiting for device... Found device!
Your phone is a [ LG-D851 ] on [ TMO ] running SW version [ V10r ] ...
Alright. We're ready to go. We're going to temproot your phone first. Press enter when you're ready!
Press [enter] to continue...
Rebooting phone...
Waiting for device... .... Found device!
Found device, checking if vulnerable...
Yep, performing temproot...
Waiting for system to settle...
Temproot worked, all done here. Moving on...
Alright, now that you're temprooted, you can press CTRL-C here and get
a temproot prompt through 'adb shell /temp/fakesu' if you're so inclined...
However, if you'd like to permaroot, let's continue.
Press [enter] to continue...
===============================================================================================
DO I NEED TO RE-ROOT?
sharkoparko said:
Thanks. I did it several times, I did number 7 also. Phone is found, it says creating permaroot....
DO I NEED TO RE-ROOT?
Click to expand...
Click to collapse
Here is the problem. You pressed to continue (enter) to create permanent root after temporary root was created
You need to press CTRL C instead , then it will exit......then continue to next step with ADB LOCAL READY.
Ill clarify this better on step 7.
Sent from my SAMSUNG-SM-N900A using XDA Free mobile app
vcurbel said:
Here is the problem. You pressed to continue (enter) to create permanent root after temporary root was created
You need to press CTRL C instead , then it will exit......then continue to next step with ADB LOCAL READY.
Ill clarify this better on step 7.
Sent from my SAMSUNG-SM-N900A using XDA Free mobile app
Click to expand...
Click to collapse
Once I click CTRL C screen disappears then I go to ADB file and follow procedures. IT STILL DOES NOT WORK
That's what I do. I clicked enter first time rooting following purple instructions. Then I realized it does not work with January update. I run purple drake again (after I found this "fix") and, as I said, I DO NOT PROCEED WITH ENTER. I use CTRL C. The window closes and I open ADB, then click start hereand follow the rest of the procedures. So YES I did click enter once initially (because purple drake post is not updated that it does not work with JAN 15 update).
sharkoparko said:
Once I click CTRL C screen disappears then I go to ADB file and follow procedures. IT STILL DOES NOT WORK
That's what I do. I clicked enter first time rooting following purple instructions. Then I realized it does not work with January update. I run purple drake again (after I found this "fix") and, as I said, I DO NOT PROCEED WITH ENTER. I use CTRL C. The window closes and I open ADB, then click start hereand follow the rest of the procedures. So YES I did click enter once initially (because purple drake post is not updated that it does not work with JAN 15 update).
Click to expand...
Click to collapse
Ok....lets do it one at a time
Once you open and run ADB LOCAL READY. When you type adb devices, is it show your device?
Let me know on which step you got stuck.
Ill try to help you
Sent from my LG-D851 using XDA Free mobile app
Just got home with a Craigslist buy.
rooted in 15min thanks vcurbel !
now to find CM12 for this baby
hi sorry for the newbiness but for some reason i donload everything i need, basically preperation is done to the T, but as soon as i click on purpledrake_windows.bat it goes into dos window and complety exits out in less then a second, so fast that i can barely read whats on that lil black screen, im pretty sure i can make out "command not found" at the end of it..any help would be greatly appreciated
tomez206 said:
hi sorry for the newbiness but for some reason i donload everything i need, basically preperation is done to the T, but as soon as i click on purpledrake_windows.bat it goes into dos window and complety exits out in less then a second, so fast that i can barely read whats on that lil black screen, im pretty sure i can make out "command not found" at the end of it..any help would be greatly appreciated
Click to expand...
Click to collapse
Did you run it as Administrator?
Did you install LG drivers and the device is being recognized as Media device?
Sent from my LG-D851 using XDA Free mobile app
all drivers are installed, the device is recognized, and nothing, when i do run it as administrater i get a whole different error msg
vcurbel said:
Did you run it as Administrator?
Did you install LG drivers and the device is being recognized as Media device?
Sent from my LG-D851 using XDA Free mobile app
Click to expand...
Click to collapse
---------- Post added at 08:43 AM ---------- Previous post was at 08:38 AM ----------
windows cannot find '.\assets\windows\bin\mintty.exe'. Make sure you type the name correctly and try again...thats the error i get when trying to run as administrator
tomez206 said:
all drivers are installed, the device is recognized, and nothing, when i do run it as administrater i get a whole different error msg
---------- Post added at 08:43 AM ---------- Previous post was at 08:38 AM ----------
windows cannot find '.\assets\windows\bin\mintty.exe'. Make sure you type the name correctly and try again...thats the error i get when trying to run as administrator
Click to expand...
Click to collapse
It seems your windows os is missing the default mintty.exe terminal...
Google it and you will find a solution to manually install it.
Or use other pc
Sent from my LG-D851 using XDA Free mobile app
tomez206 said:
hi sorry for the newbiness but for some reason i donload everything i need, basically preperation is done to the T, but as soon as i click on purpledrake_windows.bat it goes into dos window and complety exits out in less then a second, so fast that i can barely read whats on that lil black screen, im pretty sure i can make out "command not found" at the end of it..any help would be greatly appreciated
Click to expand...
Click to collapse
If I recall if the PD batch file/script is closing on you or giving you trouble, then you can run the script manually.
See link below to thecubed PD lite thread and read the 5th grey portion down of the OP, it is titled:
"But, what if I don't want to run your script to root?"
If you must use command line because the PD batch file/script is closing immediately just be sure to STOP after gaining temporary root!
From OP step 7:
IMPORTANT : READ AND DO NOT CONTINUE TO PERMANENT ROOT INSTRUCTIONS DISPLAYED. FOLLOW INSTRUCTIONS TO CONTINUE WITH ADB INSTEAD. [/FONT]
lagvoid said:
dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
This command doesn't work for me. It shows, "cannot open for read: no such file or directory".
Can you help?
Edit: Nevermind, had to repush recovery. Didn't go through properly the first time. Thank you
Everything worked great. Thank you for the guide! Rooted on 10r!
Click to expand...
Click to collapse
Hello,
I am also having the same issue. I tried the above steps a couple times and am not sure if I am doing something wrong (more than likely I am). What did you mean by repush recovery?
Try step 9 again
9- Type "adb push recovery.img /temp"
You will see that it pushes the data. it should take a few seconds
vcurbel said:
Ok....lets do it one at a time
Once you open and run ADB LOCAL READY. When you type adb devices, is it show your device?
Let me know on which step you got stuck.
Ill try to help you
Sent from my LG-D851 using XDA Free mobile app
Click to expand...
Click to collapse
-------------------------------------------------------------------------------------------------------------------------------------
C:\Users\nick\Downloads\ADB LOCAL READY>c:\windows\system32\cmd.exe
Microsoft Windows [Version 6.3.9600]
(c) 2013 Microsoft Corporation. All rights reserved.
C:\Users\nick\Downloads\ADB LOCAL READY>adb devices
adb server is out of date. killing...
* daemon started successfully *
List of devices attached
LGD851xxxxxxxx recovery
C:\Users\nick\Downloads\ADB LOCAL READY>adb push recovery.img /temp
9682 KB/s (11245568 bytes in 1.134s)
C:\Users\nick\Downloads\ADB LOCAL READY>adb shell
[email protected]:/ $ /temp/fakesu
/temp/fakesu
# Is /temp
Is /temp
/temp/fakesu: Is: not found
# dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
dd if=/temp/recovery.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
/temp/recovery.img: cannot open for read: No such file or directory
#
--------------------------------------------------------------------------------
Yes, The phone is recognized and the file as you see was pushed (see script above). I think there is some issue with this method, as other people are reporting problems following the procedure in post #1??!! I guess it work for some and it does not for others.
I'm running on the 10.5.10.IN11BA build.
Just get a command shell to your OnePlus 8 Pro through adb, no need for the device to be rooted or anything.
Once you get there, just type:
Code:
am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
It will launch the FactoryMode app and get you directly to the manual camera test view.
Just press the bottom right icon until you get to the color filter.
I have no doubt there is easier and quicker ways to get the same result, maybe through an apk.
Edit:
As far as I know, this workaround could work on any OnePlus 8 Pro model.
Also, as pointed out by ster88, you also can take videos with the filter, which was not possible with the camera app.
I tried not working. I used th terminal app from google playstore.
Can u specifically provide which app and where.
And anything to enable on developer mode.
sajjadhussaini said:
I tried not working. I used th terminal app from google playstore.
Can u specifically provide which app and where.
And anything to enable on developer mode.
Click to expand...
Click to collapse
Sure !
To enable developper mode, go to "Settings > About phone" and tap the "Build number" until they tell you have developper mode enabled.
Then go to "Settings > System > Developper options" and under "Debugging" enable "USB Debugging" and "Wireless ADB Debugging".
Once that is done, on your computer, download the platform-tools, containing adb here :
Code:
https://developer.android.com/studio/releases/platform-tools
Once it is downloaded, go inside it with your command line.
If you are doing this wirelessly, get your phone IP address and type:
Code:
adb connect <your-phone-ip-address>
Then if it worked, to know what the transport id of our device is, type :
Code:
adb devices -l
Once you have the transport id, type this to get a shell to your phone:
Code:
adb -t <transport-id> shell
You can get more details on how adb works here:
Code:
https://developer.android.com/studio/command-line/adb
Then when you have access to the shell, just type:
Code:
am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
If everything went fine, you should get access to the camera !
I could not use a terminal app to run the command, usually because the terminal app doesn't want to let the camera application to take over the view, or something like that, not sure.
The ideal would be to have a dedicated apk to run the command, at least for the time being.
Tried to launch using an app called Activity launcher and it didn't work.
play.google.com/store/apps/details?id=de.szalkowski.activitylauncher
imgur.com/a/BS9Wqzc
I'm not rooted, are you sure this works for non rooted devices? I'll try later with adb to see what happens.
Here is the error from Termux. Hope it can be loaded via apk, not sure if it suffers same restrictions:
$ am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
Starting: Intent { cmp=com.oneplus.factorymode/.camera.manualtest.CameraManualTest }
Warning: Activity not started because the current activity is being kept for the user.
From what I understood, you need to run the command from an adb shell. You cannot run it from within the phone as far as I know.
You can still run it from adb and "lock" the application so it stays in the background.
And I tried with multiple Terminal apps, the command works with none of them (Termux, Terminal Emulator, Material Terminal, etc...)
Apparently, you have some rights on the adb command shell that you don't get as a simple user on the phone.
You man are genius. I found easy way also to keep it running if needed. After getting the camera test to run, you can lock the app so phone will not close it and always return to it. Thanks, finally I can enjoy my camera
Launched it without a computer by using ADB from temux
--no root required
https://github.com/MasterDevX/Termux-ADB
*Enable wireless debugging (wireless doesn't actually need to be on)
Note wireless debugging --takes some time to take effect, sometimes up to 3-5 minutes for me.
*Run the installer above in termux,
*Type adb devices
*Type adb connect 127.0.0.1
*Accept the trusted key
*type adb shell
Troubleshooting:
*If you get an error about multiple devices type adb kill-server
*type adb devices
*type adb shell
*Accept the trusted key
*then paste in: am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
lllsondowlll said:
Here is the error from Termux. Hope it can be loaded via apk, not sure if it suffers same restrictions:
$ am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
Starting: Intent { cmp=com.oneplus.factorymode/.camera.manualtest.CameraManualTest }
Warning: Activity not started because the current activity is being kept for the user.
Click to expand...
Click to collapse
Did you get any solution for this ?
aishkumar said:
Did you get any solution for this ?
Click to expand...
Click to collapse
...
lllsondowlll said:
Launched it without a computer by using ADB from temux
--no root required
https://github.com/MasterDevX/Termux-ADB
*Enable wireless debugging (wireless doesn't actually need to be on)
Note wireless debugging --takes some time to take effect, sometimes up to 3-5 minutes for me.
*Run the installer above in termux,
*Type adb devices
*Type adb connect 127.0.0.1
*Accept the trusted key
*type adb shell
Troubleshooting:
*If you get an error about multiple devices type adb kill-server
*type adb devices
*type adb shell
*Accept the trusted key
*then paste in: am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
Click to expand...
Click to collapse
I've made a script that allows you to launch the Camera from your phone by just typing ./camera in Termux. No root needed. It can be found here: https://github.com/lllsondowlll/OP8_Camera/blob/master/README.md
can u make a video on this how u used termux and what to do whole process screen recording will be helpful coz i am new to this and i dnt wanna mess up with my phone if i lost some files or smthing please make a video i really want to play with IR camera
It works but not really required
It's working, but have few questions to myself.
1. Does it really needed?
Ans: No, you won't keep clicking pics of plastic material to see inside.
2. Is it handy?
Ans: yes, once opened you can pin/lock it in recent app and open whenever required.
It is just a IR camera and nothing wrong in it, I believe OP will enable it in future, because it really doesn't show through the clothes and even if you want to see for some black thin clothes, you need to go near.
So if you are thinking to click the nude people and go closure you will be slapped.
Few images I have taken.
babsvsphudi said:
can u make a video on this how u used termux and what to do whole process screen recording will be helpful coz i am new to this and i dnt wanna mess up with my phone if i lost some files or smthing please make a video i really want to play with IR camera
Click to expand...
Click to collapse
https://youtu.be/iVQYu-CeN24
You can't hurt anything. Just follow the instructions.
lllsondowlll said:
You can't hurt anything. Just follow the instructions.
Click to expand...
Click to collapse
thanks man you are awesome love n respect for u brother
Starting: Intent { cmp=com.oneplus.factorymode/.camera.manualtest.CameraManualTest }
Error type 3
Error: Activity class {com.oneplus.factorymode/com.oneplus.factorymode.camera.manualtest.CameraManualTest} does not exist.
connected to localhost:5555
error: more than one device/emulator
I ran it as the video shows. But I got an error like above.
Is there any way to solve this problem or is it not possible with IN2020? Please forgive me for using a translator.
pcningen said:
Starting: Intent { cmp=com.oneplus.factorymode/.camera.manualtest.CameraManualTest }
Error type 3
Error: Activity class {com.oneplus.factorymode/com.oneplus.factorymode.camera.manualtest.CameraManualTest} does not exist.
connected to localhost:5555
error: more than one device/emulator
I ran it as the video shows. But I got an error like above.
Is there any way to solve this problem or is it not possible with IN2020? Please forgive me for using a translator.
Click to expand...
Click to collapse
I was able to resolve this issue by reinstalling factory mode. I apologize to you for a fuss over. Many thanks to the developers of this method.
Since I can't get termux to work for now, another idea if you want to have it accessible all the time(*), is to run this (beautiful) command with an adb shell from a computer and then lock the app so you can't accidentally close it.
After that you can always go back to it whenever you want it!
*App won't remain locked after reboot, obviously.
lllsondowlll said:
Launched it without a computer by using ADB from temux
--no root required
https://github.com/MasterDevX/Termux-ADB
*Enable wireless debugging (wireless doesn't actually need to be on)
Note wireless debugging --takes some time to take effect, sometimes up to 3-5 minutes for me.
*Run the installer above in termux,
*Type adb devices
*Type adb connect 127.0.0.1
*Accept the trusted key
*type adb shell
Troubleshooting:
*If you get an error about multiple devices type adb kill-server
*type adb devices
*type adb shell
*Accept the trusted key
*then paste in: am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
Click to expand...
Click to collapse
I wanna piggyback on this some, since this is similar to the process I just did.
So while this works for nonroot users (I didn't actually test the nonroot version myself), if you are rooted, AND using magisk, I personally install ADB and fastboot binaries from the repo from zackptg5(?) And then just told termux to run an elevated shell (su) and then pasted in the command linked in OP:
Code:
am start -n com.oneplus.factorymode/.camera.manualtest.CameraManualTest
It then loaded the testmode camera app, and (xXx caused it to crash, I had to disable it but I don't know if it's a setting with my config) voila. It worked! Thank you.
Edit: I wanna say just running termux in root would solve the issue either way still, but, my point still is there.