Develop Bugs

[Q] Missing file issue !!

Hi Guys, for a reason or another my note 8 is stuck on Samsung logo and not starting up , its not rooted and I did a reset to default settings and still same issue.... they told me at the repair center that due to a virus , there are some files missing and they need to buy it or install it from the us server ......so , what is the best thing to do now ??

Try going into custom recovery and doing the factory reset.
If you have no custom recovery, booting into uploader mode and flash the proper from from sammobile or samungis. You will loose everything when you flash the OEM firmware.
Be sure to to use Odin 3.07.
At least you will be able to use your device again.

Thanks for the prompt reply ,i already reset it to factory sett from custom recovery and still the same , can you tell me how to boot it into uploader mode ?

alaasagaa said:
thanks for the prompt reply ,i already reset it to factory sett from custom recovery and still the same , can you tell me how to boot it into uploader mode ?
Click to expand...
Click to collapse
do you mean i should normally root my device ?

rom upgrade fail Lenovo s850

hello,need some expert advice her, i bougth a Lenovo s850 from china and i needed a multilang. rom on it wich i found on needrom but when i was finshing flashing it it went into a bootlop and now its completely dead. is it any thing to do her or have i got my self a 200$ piece of junk

graatenbil said:
hello,need some expert advice her, i bougth a Lenovo s850 from china and i needed a multilang. rom on it wich i found on needrom but when i was finshing flashing it it went into a bootlop and now its completely dead. is it any thing to do her or have i got my self a 200$ piece of junk
Click to expand...
Click to collapse
Try to explain better! Do you have installed custom recovery?

no i installed a modified multi language rom from "needroom" did every as told and everything looked fine during the upgrade and when i was finished i got the green circle that says it was ok but when started it up it went in to boot loop and said "TOOL DL image fail!" but after a while its totally dead.,when i try now it wont load in any software into the phone ,just starts up the purple pre preparation on the SP flash tool but when i connect the phone it stops .cant get it into recovery mode or anything,just completely dead. i would rely be thankful for some advice her

Maybe the package you've tried to install is corrupted.

most likely, but is there anything to do with it or is it over for it.

graatenbil said:
most likely, but is there anything to do with it or is it over for it.
Click to expand...
Click to collapse
Most likely your device is unusable. Without any recovery, I dont think you will be able to do anything. I am sorry.

OK a 200$ experience richer , thanks anyway

graatenbil said:
OK a 200$ experience richer , thanks anyway
Click to expand...
Click to collapse
Just a question....are you able to enter fastboot?

no cant enter anything its like its out of battery,completely dead and it wont take charge ether

graatenbil said:
no cant enter anything its like its out of battery,completely dead and it wont take charge ether
Click to expand...
Click to collapse
hello my friend. I got exactly the same thing that I just tried to install TWRP. I stuck in Boot loop. solution found by disconnecting the battery. and making again the same procedure. but once I checked her DA DL All. Now how puts the battery is another story .but if I want i tell you, you need some tools that may have in your home..

graatenbil said:
no cant enter anything its like its out of battery,completely dead and it wont take charge ether
Click to expand...
Click to collapse
Question: When you connect the phone with your pc (usb cable) does the pc makes any sound (connected device sound)?

setmov said:
Question: When you connect the phone with your pc (usb cable) does the pc makes any sound (connected device sound)?
Click to expand...
Click to collapse
Same problem here. Trying to install twrp and got stuck in => FASTBOOT mode ...
The computer makes a sound when i connect the USB cable but i don't have adb connection.
How can I solve this problem?
Do I leave it to finnish the baterry and than try to start?

RE
leo_alex82 said:
Same problem here. Trying to install twrp and got stuck in => FASTBOOT mode ...
The computer makes a sound when i connect the USB cable but i don't have adb connection.
How can I solve this problem?
Do I leave it to finnish the baterry and than try to start?
Click to expand...
Click to collapse
The phone started in normal mode after the battery dryed and the phone went off.

Hi, has anyone Lenovo S850 firmware upgrade solution? Now I have resolve "DL Tool Image Fail" problem but have another problem - every rom I download touch screen doesn't work. On "original" rom (not multilanguage) touch screen worked properly. Does anyone have "good" multilanguage rom with touch screen working?

method to install original rom android 4.4.2 in lenovo s850
i have found the perfact solution to install original 4.4.2 rom on lenovo s850...so for that you have to donload rom from the link in notepad file...i have uploaded notepad file and download link is in that it is about 1.1 gb...so it will take time to download and after that what you have to do is open flash tool and then check da dl check sum and then extract the file you have download of 4.4.2 android and then in flash tool click on scater loading and browse to the the extraction location and in extracted folder there will be a folder somethinf target bin in that folder select scatter loding file of lenovo s850 and then just simply click on upgrade firware and then switch off your phone and then wait to process complete untill green circle come...and if you dont have flash tool...google it and download...thanks i hope this helps someone...:good::good::good::good:

Dear devs, help me out on UNBRICKING LENOVO S850:
Initial Problem was: AFTER TURNING PHONE ON (NORMAL BOOT UP) IT GOT STUCK ON BOOT LOGO.
Very first tried solution: PRESSING BOTH VOL.+POWER PHONE WENT IN LENOVO RECOVERY MODE. THEN I TRIED TO FUSE FORMAT BUT IT FAILED TO FORMAT. PROBLEM REMAINED SAME.
Second Tried Solution: DOWNLOADED OFFICIAL STOCK ROM (A. Lenovo_S850_VIBEUI_V1.5_1419_2_ST_S850_4.4.2 B.Lenovo_S850_ROW_S211_140923 C. Lenovo_S850_ROW_S207_140814. D. Lenovo S850 official firmware flash file) + ALL AVAILABLE SP FLASH TOOLS + USB VCOM DRIVER FOR MEDIATEK AND INSTALLED DRIVERS.
USING ABOVE FILES I TRIED TO DOWNLOAD ALL ROMS WITH DIFFERENT SP FLASH TOOLS VERSIONS BUT ALL THE TIME RED BAR CAME TO 100% THEN BAR STUCK ON 0% FOLLOWED BY ERROR "SDMMC WRITE FAIL".
THEN I TRIED UPGRADING FIRMWARE, SAME AGAIN IT GAVE ERROR "FORMAT FAILED"
THEN I TRIED TO FORMAT USING FLAH TOOL (ALL VERSIONS) AGAIN IT GAVE SAME ERROR "FORMAT FAILED"

crazy
ur cable problem pp

Phone stuck in bootlop, can't enter droidboot

Hi guys ,
a bit of a novice here , i have the ZE550ML edition and have tried rooting my phone
the steps that lead to this problem are as follows
- tried to root the phone using one of the utilities on this forum - kept getting error messages saying not allowed to write on partition
- tried to unlock bootloader by using one of the utilities on this forum - failed and device was stuck in bootlop but could enter droidboot and recovery , was detectable as moorfield on the pc
- tried to flash the official rom image using asus flash utility and now stuck in bootloop but can't enter droidboot at all , my pc does not discover the phone anymore either
is there anything i can do further to fix my phone or am i screwed ?
sorry if this was already posted , i tried to find answeres on older posts but nothing help

magnus_fancy said:
Hi guys ,
a bit of a novice here , i have the ZE550ML edition and have tried rooting my phone
the steps that lead to this problem are as follows
- tried to root the phone using one of the utilities on this forum - kept getting error messages saying not allowed to write on partition
- tried to unlock bootloader by using one of the utilities on this forum - failed and device was stuck in bootlop but could enter droidboot and recovery , was detectable as moorfield on the pc
- tried to flash the official rom image using asus flash utility and now stuck in bootloop but can't enter droidboot at all , my pc does not discover the phone anymore either
is there anything i can do further to fix my phone or am i screwed ?
sorry if this was already posted , i tried to find answeres on older posts but nothing help
Click to expand...
Click to collapse
if you are not able to go to recovery of fastboot mode. following is the only way to get out of it. read carefully. do as suggested. go to other point after completing one properly. do not use asus flash tool after you enter fastboot mode. use commands to flash raw firmware. see section flash firmware without AFT. OFC after you get fastboot mode back.
https://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
if you have any other question please post in above thread only.

Bricked my phone... :(

Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone

Solution
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I've used MiFlash Tool, and the problem was fixed. Sahara Error occurs when you take to much time to flash after booting to EDL, you only have few seconds to flash util the port is closed for writing. QFIL takes around 20 to 25 seconds in caching the files so use MiFlash and It'll flash. Best way to do it is:
1. Install and setup MiFlash for flashing.
2. Open MiFlash and select your Firmware's folder.
3. As soon as you connect the phone refresh miflash and hit flash.
If everything goes well you'll flash will be successful else try again.

I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.

Chin_hebbar said:
I tried doing as fast as a could too on mi flash and it would come up as trying to connect to com4 port something in the status and would eventually come back to same error in the picture.
Click to expand...
Click to collapse
I need to flash Baseband for Oreo. Please guide me

windows 10 problem
Chin_hebbar said:
Hello there I had just unlocked the bootloader yesterday and flashed an Oreo ROM without updating base bands and now my device doesn't boot up it just shows the bootlogo and turns off again in less than a second it doesn't even charge, good thing is I am able to go to edl mode I guess but then when I tried qfil and mi flash to flash stock rom i m getting the sahara cannot detect com port handle error and the system cannot find the file specified error in mi flash please help its just been a week since I got this phone
Click to expand...
Click to collapse
I face this problem in windows 10.
first uninstall zuk drivers and qfill and disable driver signature enforcement (Google it how to do it) then install zuk drivers and qfill use original cable and your phone will get flashed

Balaji Sriram said:
I need to flash Baseband for Oreo. Please guide me
Click to expand...
Click to collapse
Follow the instruction from this post
https://forum.xda-developers.com/lenovo-zuk-z2/how-to/zuk-z2-baseband-flashing-guide-t3715121

Do not listen to anyone telling you to use miflash, only use qfil otherwise you WILL encounter other issues because qfil is the only way to reach the deeper partitions that mi is unable to... Other issues may range from no volte, calling or signal problems etc its just easier to do it right the first time.

Need Help, my mi6 hard brick, no fastboot mode.. set boot partition failed

hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...

You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.

-Zteam- said:
You can try to use XiaomiTool and flash your phone with instead.
https://www.xiaomitool.com/V2/
Also, have you tried fastboot boot recovery.img
To see if you can boot TWRP or something?
(fastboot boot might work better than flashing)
I don't have any experience with Miflash, so can't offer any advice on that.
Personally I would try fastboot boot first, since XiaomiTool is in alfa-version.
Click to expand...
Click to collapse
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:

zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
it seems your Mi6 is alive again how was the solution?

DJ Regino said:
it seems your Mi6 is alive again how was the solution?
Click to expand...
Click to collapse
no , still dead.. :crying:

look into https://stackoverflow.com/questions/39906951/android-edl-mode-commands

zilan said:
thanks for replying.. my phone is dead can't boot to fastboot. only detect in edl mode. i think its problem with my partition being messed up (look from mi flash logs)
anyway i have tried to install xiaomitool v2 but i think it's not compatible yet with unbrick device it show error like this:
Click to expand...
Click to collapse
Sorry for my late reply, I had forgotten to answer this earlier, did you try to perform a regular flash (not bricked option) from XiaomiTool. if that doesn't work either, maybe you should ask the developer of XiaomiTool2 for hints.

Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc

HTCDevil said:
Try mipcsuite chiese version, i saved my Mi6 when it showed penguin in the middle of screen, no fastboot nor recovery etc
Click to expand...
Click to collapse
do you have a link? and what rom to use?

zilan said:
do you have a link? and what rom to use?
Click to expand...
Click to collapse
Is there any update? Did your phone recovered from that situation?

I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.

zenhex said:
I am in the same situation with my Asus Rog 2. It has life sign only in edl mode and when I try to recover I ve got that error too "set boot partition failed" still dead.
Click to expand...
Click to collapse
u fix it?

zilan said:
hello, my mi6 suddenly dead, hard brick, can't enter to fastboot mode. Mi6 6/128 ceramic edition.
so i decided to open back covers and shortlink 2 pins it detect as qualcomm loader in mi flash, but when flashing fastboot rom it always show error " set boot partition 1 failed "
i tried many version of mi flash and use global stable, global dev, china stable, china dev fastboot rom but always ended in set boot partition failed..
i've searching lots of forum but can't found an answer for set boot partition failed error.
i also tried QPST for flashing with fastboot rom but also give error,
please help anyone have same problem with me? or any xiaomi engineer here? i just need how to solve flashing in mi flash with error set boot partition failed.
i hope no need to change/replace the hardware...
Click to expand...
Click to collapse
if you're still there, i resolve this issue.
you need to jump charge your battery using external charger ( external charger jumped wire direct on your battery). maybe for 30mins.
then try again to charge your phone, if it reapond and have display 0% battery, let it charge for atleast 50% then power ON.
If it stucks on logo.. do reflash.